U English Front Surround System EN Quick Start Guide
Contents Before using the unit ............................................................ 3 Features ....................................................................................................................3 PREPARATION Supplied items ...................................................................... 4 Part names and functions .................................................... 6 Installation ............................................................................ 9 Connections ......
Before using the unit Features Introduction This front surround system allows for the enjoyment of dynamic sound with video played on a TV. AirPlay TV Internet radio Streaming service Playback device (BD/DVD player) Computer (NAS) Wireless router The unit • Play audio from a TV or BD/DVD player in surround sound. • Play audio from a Bluetooth device with excellent quality. • Play audio over a network with superior sound quality.
PREPARATION Supplied items Make sure you have received all of the following items. Center unit (ATS-CU4080) Wireless subwoofer (NS-WSW43) In this manual, the wireless subwoofer is referred to as “subwoofer”. Remote control Power cord × 2 Optical digital audio cable A CR2025 Lithium battery has already been inserted into the remote control.
Preparing the remote control Replacing the battery in the remote control Remove the battery’s insulating strip before attempting to use the remote control. Press and hold the release tab firmly in the direction indicated by [A], and slide the battery holder out in the direction indicated by [B]. Battery holder Battery’s insulating strip Release tab Operating range of the remote control Operate the remote control within the range as shown below.
Part names and functions Center unit (front panel/top panel) a b c d e f g f a Indicators e z (power)/CONNECT The indicators on the top panel flash or glow, to show the operation and setting status. In this manual, indicators status, such as off, glowing, and flashing, are shown as the illustrations below. : Off : Glows : Flashes • The brightness of the indicators can be changed using DIMMER on the remote control (p. 17). b y (input) Select an input source to be played back (p. 14).
Center unit (rear panel) The illustrations in this manual include labels next to the jacks on the bottom of the unit for easy identification. b c e d f g a a AC IN jack Connect the power cord of the center unit (p. 11). b NETWORK jack For connecting to a network with a network cable (p. 18). c HDMI OUT (ARC) jack For connecting to an HDMI-compatible TV and outputting video/audio signals (p. 10).
Subwoofer b a c a Bass reflex port d STANDBY indicator Shows subwoofer’s status (p. 13). b AC IN jack Connect the power cord of the subwoofer (p. 11). Use to pair the center unit with the subwoofer manually. En PREPARATION e * indicator Glows when the center unit and subwoofer are connected wirelessly (p. 12).
Installation The center unit can be installed on a TV stand, etc. Position the subwoofer to the left or right of the center unit. Angle the subwoofer slightly toward the center of the room to prevent sound from reflecting off of walls. Installing the center unit on a TV stand Position the center unit with the touch panel facing up. NOTICE • Do not stack the center unit and a BD player or other device directly on each other. Doing so may cause a malfunction due to vibrations.
Connections a Connecting a TV and set-top box For the cable connection, follow the procedure below. 1 HDMI INPUT 2 OPTICAL OUTPUT 3 : Video signals : Audio signals 1 HDMI cable (sold separately) The digital audio/video signals from the set-top box or BD/DVD player are input to this unit. 2 HDMI cable (sold separately) Digital video from the set-top box or BD/DVD player is displayed on the TV.
b Connecting a game console via the analog jack c Connecting the power cord Connect an external device, such as a game console or TV that does not have an optical digital audio output, to the ANALOG input jack of the center unit. Once all connections have been made, connect the supplied power cords to the AC IN jacks on the center unit and subwoofer respectively, and plug the power cords into AC wall outlets. Center unit 3.
d Turning on the unit Press z (power) on the remote control or touch z/CONNECT on the center unit. The unit turns on and the center unit and subwoofer are automatically connected via wireless connection. Once the connection has been successfully established, the * indicator on the subwoofer’s rear panel glows, and the unit is ready for playback. Glows Turn on the unit or NOTE • If the * indicator on the subwoofer does not glow properly, see “No sound is coming from the subwoofer” in the Owner’s Manual.
PLAYBACK Operations Remote control signal transmitter Transmits infrared signals. 1 z (power) button NOTE • When the unit is turned on for the first time after purchase, the * indicator on the center unit flashes slowly. Turns on or off the unit. 1 Center unit Turned on The indicator for the last input source selected glows. Indicates the surround setting, and network or Bluetooth connection status. While the * indicator is flashing, network settings from your iOS device (an iPhone, etc.
2 3 Input buttons 3D SURROUND, SURROUND and STEREO buttons Select an input source to be played back. TV ....................TV audio or sound from a device connected to the unit’s TV input jack HDMI................Sound from a device connected to the HDMI input jack ANALOG .........Sound from a device connected to the ANALOG input jacks BLUETOOTH ..Sound from a Bluetooth connected device NET..................
4 5 SUBWOOFER (+/-) buttons CLEAR VOICE button Adjust the volume of the subwoofer. Enable/disable the clear voice function. When this function is enabled, human voices such as lines in movies and TV shows, or news and sport commentary, are played clearly. Volume down (–) Volume up (+) VOLUME (+/-) buttons Enabled: Flash three times and turn off Disabled: Flash once and turn off Adjust the volume of the unit.
6 INFO button Press INFO to confirm the type of audio signal being played, as well as settings for functions such as the bass extension function. The indicators on the unit will show the following audio information for three seconds immediately after INFO is pressed. a b a Show the type of audio signal. HDMI glows (white): Dolby Digital HDMI glows (red): DTS TV glows (white): AAC HDMI and TV off: PCM/analog input/no input b Show whether Dolby Pro Logic II is enabled or disabled.
7 7 8 FAVORITE (1–3) buttons DIMMER button Use the FAVORITE button to register input sources played over a network (Internet radio stations, music files stored on a media server, etc.) as favorites. Register favorites with the FAVORITE buttons 1 Play the input source to be registered. 2 Press and hold FAVORITE 1, 2, or 3 at least three seconds. Change the brightness of the indicators. Each time DIMMER is pressed, the brightness of the indicators changes as follows.
NETWORKS Connecting to a network Network functions and the MusicCast CONTROLLER app A network connection allows you to listen to Internet radio stations or music streaming services, and to use AirPlay to play music files, or to play music files stored on your computer (media server) via this unit. Most playback requires the “MusicCast CONTROLLER” app for mobile devices. Install and use the MusicCast CONTROLLER app on your mobile device to play music files.
Wireless network connections Connect the unit to a wireless router (access point) to use a network. Connecting with the MusicCast CONTROLLER app (registering the unit as a MusicCast-enabled device) Install the MusicCast CONTROLLER app on your mobile device to connect the unit to a network and register it as a MusicCast-enabled device. Internet NOTE Wireless router (access point) Modem • Confirm that your mobile device is connected to your home router before beginning.
3 5 Turn on the unit, and then tap “Next”. Follow the on-screen instructions to configure network settings. NOTE • When a screen like that below is displayed, follow the on-screen instructions to configure network settings. 1. Use the Home button on your mobile device to return to the Home screen. 2. Select “Wi-Fi” from “Settings”. 3. Select “MusicCastSetup” from “CHOOSE A NETWORK...”.
6 To register the unit as a MusicCast-enabled device, configure the following items. • Location name (“home”, “John’s house”, etc.) • Name and photo of the room where the unit is installed The location name, and the name and photo of the room where the unit is installed can be changed later. NOTE • If a different MusicCast-enabled device is already registered with the MusicCast CONTROLLER app, tap ~ (Settings) in the room selection screen, and then select “Add New Device” to add the unit to the app.
Specifications Bluetooth Specifications (ATS-CU4080) Amplifier section Maximum rated output power Front L/R 50 W × 2ch Type Acoustic suspension type (non-magnetic shielding) Driver 4.6 cm (1-3/4”) cone × 4 Frequency response 160 Hz to 9 kHz Impedance 4 Ω (8 Ω × 2) Driver 2.5 cm (1") dome × 2 Frequency response 9 kHz to 23 kHz Impedance 4Ω Speaker section Front L/R Tweeter Bluetooth version Ver 4.
Specifications (NS-WSW43) General Power supply Power consumption Standby power consumption U.S.A. and Canada models AC 120 V, 60 Hz Australia model AC 240 V, 50 Hz Europe, Asia, and Russia models AC 110 to 240 V, 50/60 Hz U.K.
Yamaha Global Site https://www.yamaha.com/ Yamaha Downloads https://download.yamaha.