User Manual
Table Of Contents
- PRECAUTIONS
- NOTICE
- Information
- Introduction
- Included Accessories
- About this Manual
- Contents
- Component Names
- Setting Up
- Screen Configuration and Basic Operation
- Producing Reference Tones for Playing Harmony (Voice, Temperament, Hold, Octave, Transpose)
- Demonstrating Tempo and Rhythm (Metronome, Rhythm Style)
- Sharing Performances (Recording/Playback)
- Enhancing Basic Practice (Sound Back, Training)
- Restoring Factory Settings
- Advanced Settings (Settings)
- Connecting External Devices
- Connecting Amplifiers or Other Equipment (OUTPUT [L/MONO], [R] jacks)
- Connecting a Microphone (MIC [INPUT] jack, MIC [GAIN] knob)
- Using a Pedal ([FOOT PEDAL] jack)
- Connecting a USB Flash Drive (USB [TO DEVICE] terminal)
- Connecting to a Computer (USB [TO HOST] terminal)
- Using the “HD-300 Assistant” iPhone/iPad App (Bluetooth)
- Listening on the HD-300 to Audio Playback from an iPhone/ iPad (Bluetooth)
- Appendix
HD-300 Owner’s Manual
31
You can change advanced settings on the Settings screen.
Press the [SETTING] button to call up the Settings screen. Press
the [EXIT] button to exit from the screen.
Select an item using the CURSOR [L][R] buttons, and then use
the [-]/[+] buttons, or the dial to change values.
To return the selected item to its default value, press both [-]/[+]
buttons simultaneously.
Items in the Settings screen are as follows.
(*) Items with this mark are for display only and cannot be changed.
Advanced Settings (Settings)
Name Description Settings
Standard Pitch
Sets the standard pitch. 430.0 – 450.0 Hz
Metronome Sound
Sets the metronome sound. Peck: This is the same tone used by the HD-200.
Click: This is a mechanical metronome tone.
Beep: This is an electronic metronome tone.
Metronome Pattern
Sets the metronome pattern (page 23). All: The metronome plays back all beats.
Alternate: The metronome plays back beats so that
multiple click sounds are not doubled at the same timing.
Sound Back Time
Specifies the duration until the sound
produced by the HD-300 turns off after
there are no more input sounds when the
Sound Back feature is turned on.
Short: approx. 2 sec.
Long: approx. 4 sec.
Pre Time Shift Rec
Specifies the number of seconds recorded
before the [REC] button is pressed while in
Time Shift Recording mode.
3 – 10 sec.
Post Time Shift Rec
Specifies the number of seconds until a
recording automatically stops after starting
or extending a recording in Time Shift
Recording mode.
5 – 20 sec.
Bluetooth
Sets the Bluetooth communication mode. Off: Use this to disable Bluetooth communication.
On: Use this to connect to a paired device.
Pairing: Use this to switch to pairing mode.
BD Address (*)
Displays the MAC address for the HD-300
as a Bluetooth device.
—
LCD Contrast
Adjusts the contrast of the LCD. 0 – 20
Foot Pedal
Sets functions of the pedal connected to the
[FOOT PEDAL] jack.
Volume: This adjusts the main volume.
Hold: This produces the same effect as the [HOLD]
button.
Start/Stop: This produces the same effect as the [START/
STOP] button.
Rec: This produces the same effect as the [REC] button.
Auto Power Off
Enables/disables the Auto Power Off
function.
Disable: This disables the Auto Power Off function.
Enable: This enables the Auto Power Off function.
NOTE
The amount of time that elapses before the power is
automatically turned off depends on the type of power
being used. This is set to 30 minutes for battery power, and
two hours when using an AC adaptor.
Language
Sets the language of alert messages and
file names that appear in training mode.
English, Japanese
Firmware Version (*)
Displays the firmware version. —