Owner`s manual

389
Appendix
Appendix
• Is the input signal routed appropriately to the
recorder? *
* If the signal is being input appropriately to the
recorder, pressing the [REC TRACK SELECT] key will
cause the meter to react.
* If the signal is being input appropriately to the
recorder, pressing the [REC TRACK SELECT] key will
cause the meter in the METER screen to react.
• When a file input/output page such as the SONG
screen Song List page is displayed, recording and
playback are not possible.
• CD/DAT DIGITAL REC in the UTILITY screen Pre-
fer.2 page may be set to DISABLE.
• Please read and understand the copyright warning
(→P.174) before using digital input signals.
■ Can’t record on the STEREO track
• It is not possible to record on the STEREO track
while recording on other tracks.
■ Can’t play back the STEREO track
• Muting may be selected in the TRACK screen Stereo
page.
• Are monitor channels 1 and 2 raised? *
* For STEREO track playback mode, the signal is out-
put from monitor channels 1 and 2.
■ Not all tracks will play back
• There are limitations on the number of tracks that
can be simultaneously recorded or played. Refer to
Operation section “Audio tracks”.
■ The volume of a particular channel increases or
decreases
• Are the dynamics processor settings appropriate?
• Automix may have been recorded.
■ Faders move to the lowest position on their own
• Automix may have been recorded.
■ Meters move even though the faders are lowered
• The direct out setting may be PRE EQ or PRE
FADER.
• The meter display may be set to PRE FADER.
■ Can’t store a scene
• Is the scene memory protected?
• A scene cannot be stored in scene number 00.
■ Can’t reproduce a scene
• One or more channels may be set to Recall Safe.
■ Can’t recall a scene during recording
• The AW2816 may be set to record the digital input
signal.
• Make sure that CD/DAT DIGITAL REC is set to
ENABLE.
■ Can’t change input patches during recording
• The AW2816 may be set to record the digital input
signal.
• Make sure that CD/DAT DIGITAL REC in the UTIL-
ITY screen Prefer.2 page is set to ENABLE.
■ Can’t save to a library
• It is not possible to save to the factory-preset librar-
ies.
■ Can’t recall a channel library to the stereo output
channel
• Channel libraries saved from other channels cannot
be recalled to the stereo output channel.
■ Can’t exchange MIDI data
• Are the MIDI cables connected correctly?
• A MIDI cable may be broken.
• Is the power turned on for the transmitting and
receiving devices?
• Do the channel settings match for the transmitted
and receiving devices?
• Are the MIDI screen/MIDI Setup page settings set
appropriately?
• Is a scene assigned to the program change number
being transmitted?
■ MIDI messages are looped
• In the MIDI screen MIDI Setup page, ECHO may be
turned ON.
• Also check the settings of the connected external
MIDI devices.
■ MTC messages are not transmitted
• Is the MIDI cable correctly connected to the MTC
OUT connector?
• If the cable is connected to the MIDI OUT connec-
tor, is the MTC ON/OFF setting turned ON?
• Is SYNC OUT set correctly?
• Is MTC SYNC set to MASTER?
■ The AW2816 does not synchronize to incoming
MTC messages
• Is the MIDI cable connected to the MIDI IN con-
nector?
• In the MIDI screen MIDI Sync page, is MTC Sync
set to SLAVE?
■ MTC messages are received, but synchronization
drifts
• Is a large amount of MIDI data (notes etc.) being
received together with the MTC messages?
■ MTC synchronization drifts
• Does the frame rate match between the AW2816
and the external device?
• SYNC OFFSET may have been set.
• If jumps occur in the synchronized time, change the
SYNC AVE. setting in the MIDI screen MIDI Sync
page, and try again.
■ Something happens to the sound when the [DATA/
JOG] dial, [SHUTTLE] dial, [FF] key, or [REW] key
are operated
• Differences in the number of simultaneously played
tracks will affect the way in which the sound is
heard when these controls are operated.