UCA Compact Disc Changer Changeur Compact Disc OWNER’S MANUAL MODE D’EMPLOI
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
IMPORTANT SAFETY INSTRUCTIONS FCC INFORMATION (for US customers) 1 IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2 IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 Install this sound system in a well ventilated, cool, dry, clean place – away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. For proper ventilation, allow the following minimum clearances. Top : 2.5 cm (1 inch) Rear: 2.5 cm (1 inch) Sides: 2.
CONTENTS INTRODUCTION INTRODUCTION CONTROLS AND FUNCTIONS ......................... 2 Front panel ................................................................. 2 Rear panel connections .............................................. 4 Remote control........................................................... 5 OPERATION OPERATION LOADING AND PLAYING DISCS ..................... 8 Program playback Audio CD .................................. 8 PLAYXCHANGE ..................................................
INTRODUCTION CONTROLS AND FUNCTIONS Front panel 1 Disc tray Loads a disc. 7 Remote control sensor Receives signals from the remote control. 2 (Open/Close) Opens or closes the disc tray. For loading and unloading discs, see page 8. 8 iPod/USB port Connect your iPod or USB device. See page 9 for details. 3 (Power) Press inward to the ON position to turn on the power. y • The power indicator above lights up when this unit is turned on.
CONTROLS AND FUNCTIONS I Time and playback mode indicator Indicates the current playback mode and the status of the time display (see pages 5 and 8 for playback modes, and page 6 for time display). Note J Advanced setup indicator Indicates the enabled special modes. See “USING THE ADVANCED SETUP” (page 13) for details. The number corresponding to an empty tray may light up before the tray is selected.
CONTROLS AND FUNCTIONS Rear panel connections CAUTION Before making any connection, switch OFF the power to the unit, the amplifier and any other component. Optical digital cable Audio cable (supplied) RS-232C terminal Amplifier AC IN inlet REMOTE CONTROL IN/OUT terminals The audio signals are only output from the ANALOG OUT jacks when the PURE DIRECT mode is on.
CONTROLS AND FUNCTIONS Remote control INTRODUCTION 4 PROGRAM Turns on or off the program playback mode. See “Program playback” on page 8. 5 DIMMER Each time you press DIMMER, the brightness level changes by 4 levels. y This setting is retained even if you turn off this unit. 6 Numeric buttons Use to select directly a track on the disc or a file in the current folder. 7 (Search backward), (Search forward) Searches tracks backward/forward while the button is pressed.
CONTROLS AND FUNCTIONS E REPEAT Repeats playback of a single track or all tracks. Each time you press REPEAT during playback, the repeat playback mode changes as follows: • REP TRACK (single repeat playback): A single track is played back repeatedly. • REP ALL (all repeat playback): All tracks (the entire disc) are played back repeatedly. Data Disc H CLEAR Erases the programmed track. I ENTER Confirms a track number entered when you are programming tracks. J (Pause) Pauses playback.
CONTROLS AND FUNCTIONS ■ Installing batteries in the remote control Press the part and slide the battery compartment cover off. 2 Insert the two supplied batteries (AA, R6, UM-3) according to the polarity markings (+ and –) on the inside of the battery compartment. 3 Slide the cover back until it snaps into place. ■ Using the remote control The remote control transmits a directional infrared beam.
OPERATION LOADING AND PLAYING DISCS You can load or replace five discs at a time. 1 Press OPEN/CLOSE to open the disc tray and load discs. Use the disc guides to align the discs correctly in the tray. Label side upward 1 Press PROGRAM while playback is stopped. This unit is set to the program editing mode. 2 Select a disc with one of the DISC (1-5) buttons on the front panel or DISC SKIP / on the remote control. 3 Select a track by using the numeric buttons and ENTER.
PLAYING BACK iPod/USB DEVICE Connecting iPod/USB devices Notes iPod • Use the USB cable supplied with your iPod. If no USB cable is supplied, purchase one from Apple Inc. • Turn off your iPod. • Do not use a USB hub. OPERATION 1 4 Connect your USB device or iPod via USB cable Playing back iPod 1 2 Press CD/USB to select the iPod/USB mode. The iPod/USB indicator on the front panel lights up in orange, then changes to green when playback is ready.
PLAYING BACK iPod/USB DEVICE Disconnecting iPod/USB devices Stop playback, and then disconnect your iPod or USB device. It is recommended that you press CD/USB to switch to the CD mode, confirm that the CD/USB indicator goes off, and then disconnect your iPod/USB device. CAUTION Do not disconnect your iPod or USB device while playing back from the connected device, or while “USB READING” appears in the front panel display.
ADDITIONAL INFORMATION PLAYABLE DISC AND FILE FORMAT ■ Playable MP3 and WMA files (USB device and Data Disc) ■ Playable discs Use compact discs bearing the marks below. MP3 Bitrate (kbps) Sampling frequency (kHz) MPEG 1 Audio Layer-3 32-320 * 32/44.1/48 MPEG 2 Audio Layer-3, 2 8-160 * 16/22.05/24 MPEG-2.5 Audio Layer-2 8-160 * 8/11.025/12 Format .... Compact discs (digital audio) .... CD-R, CD-RW digital audio discs • CD-R or CD-RW discs bearing one of the following phrases.
PLAYABLE DISC AND FILE FORMAT ■ Handling compact discs • Always handle with care so that the playing surface is not scratched. Do not warp discs. • To keep clean the playing surface, wipe with a clean, dry cloth. Do not use any type of disc cleaner, spray, or any other chemical-based liquid. • Do not wipe with a circular motion; wipe straight outward from the center. • Use a soft-tipped pen when writing on the label side of the disc.
USING THE ADVANCED SETUP This unit is equipped with the following four special modes, which may be useful for special purposes at stores or offices. To activate and configure Advanced setup, follow the steps below. Use the buttons on the front panel. Note Activate Advanced setup POWER OFF The special mode functions are incompatible with iPod.
TROUBLESHOOTING If the unit fails to operate normally, check the following points to determine whether the problem can be corrected by the simple measures suggested. If it cannot be corrected, or if the problem is not listed in the Problems column, disconnect the power cable and contact your authorized Yamaha dealer or service center for help. Possible Causes This unit fails to turn on. The power cable is not connected to the AC IN inlet on the rear panel or not plugged in the wall outlet.
TROUBLESHOOTING Problems Possible Causes Solutions Refer to page This unit is being subjected to vibrations or impacts. Relocate this unit. The disc is dirty. Clean the disc. 11 Sound “hums”. Improper cable connections. Securely connect the audio cables. If the problem persists, the cables may be defective. 4 Noise from a nearby tuner. The tuner is too close to this unit. Move the tuner and this unit farther apart or turn off this unit. — Noise from inside of the disc tray.
© 2009 Yamaha Corporation All rights reserved.
