AB Compact Disc Player OWNER’S MANUAL © 2014 Yamaha Corporation Printed in Malaysia ZK27080
A Living Tradition in Sound A piano comes into this world through the perfect synergy of advanced technical skill and artistry. Such a piano can create sound that truly reflects the player’s feelings. The final stage in piano production is called “voicing”. It is here that the instrument is given its soul.
Excellence in Audio Achievement First HiFi System introduced in 1920 We introduced numerous HiFi components (turntables, FM/AM tuners, integrated amplifiers, preamplifiers, power amplifiers and speakers) in 1955 - 1965. CA-1000 NS-20 Natural Sound Speaker Series introduced in 1967 NS-20 Monitor Speaker CA-1000 Integrated Amplifier Featuring A-Class operation, the CA-1000 set the standard for integrated amplifiers.
◆ Full-stage balanced signal transmission beginning with the DAC achieves the ultimate in CD reproduction ◆ Independent power supplies with digital and analog completely separated ◆ Exclusive Yamaha loading mechanism and high precision CD drive ◆ Left-right symmetrical design with rigid, stable construction ◆ Pure Direct ◆ Super sound from Super Audio CDs ◆ Heavy feet with newly-developed antivibration spikes ◆ DSD playback via 192 kHz, 24-bit USB DAC ■ Supplied accessories Please check that you have recei
CONTROLS AND FUNCTIONS Controls and functions In this chapter, you will learn the controls and functions of CD-S2100.
Controls and functions ■ Front panel (pages 6 to 9) SA-CD HYBRID TRACK TOTAL REMAIN PROG SHUFFLE REPOFFSALL PURE DIRECT STANDBY/ON SOURCE LAYER SOURCE LAYER SA-CD CD DISC USB OPTICAL COAXIAL OFF 1 2 34 5 6 1 STANDBY/ON, OFF switch Turns on or off this unit. STANDBY/ON (upper position): In this position, you can select STANDBY or ON, using the p CD key on the remote control. 7 8 2 STANDBY/ON indicator Lit brightly: Shows that the power of the unit is ON.
5 SOURCE key Selects the audio source to be played back. Each time you press this key, the audio source is switched. (coaxial digital input) (optical digital input) y The audio source setting is retained even if you turn off this unit. 6 LAYER key Switches the playback layer of a hybrid Super Audio CD between SA-CD and CD while playback is stopped (page 27). y This setting is retained even if you turn off this unit.
Controls and functions ■ Front panel (pages 6 to 9) 9 0 A C B D E SA-CD HYBRID TRACK TOTAL REMAIN PROG SHUFFLE REPOFFSALL STANDBY/ON PURE DIRECT SOURCE LAYER SOURCE LAYER SA-CD CD DISC USB OPTICAL COAXIAL OFF F 9 Remote control sensor Receives signals from the remote control. 0 Display The brightness can be adjusted with the DIMMER key on the remote control (page 12). A (playback) / (pause) indicator Lights in the playback/pause mode.
H I J K F Disc tray Loads a disc. I (Play) key Starts playback. G J (Pause) key Pauses playback. Press the playback. (Open/Close) key Opens or closes the disc tray. y The disc tray also closes automatically when you press: • the (Play) key on the front panel or on the remote control. • the front edge of the disc tray gently. • a numeric button on the remote control. H K or key to resume (Stop) key Stops playback.
Controls and functions ■ Rear panel 1 2 3 USB BALANCED OUT ANALOG OUT BALANCED OUT SYSTEM CONNECTOR GND 1 2 5 OPTICAL COAXIAL DIGITAL IN REMOTE IN +HOT 4 OUT 3 - COLD 8 9 See page 18 for connection information.
6 7 OPTICAL COAXIAL DIGITAL OUT AC IN 0 A 0 AC IN inlet Use this inlet to plug in the supplied power cable. See page 20 for connection information. A Foot The feet of this unit include built-in spikes. Using the spikes can reduce the effect of vibrations on the set. When using the spikes, remove the transport tape, then remove the magnet foot by pulling it. Caution • Take care that the magnet foot is not accidentally swallowed by small children.
Controls and functions ■ Remote control 3 1 4 p AMP key Turns the Yamaha amplifier ON or switches it to STANDBY mode. 2 3 OPEN/CLOSE key Opens or closes the disc tray. AMP OPEN/CLOSE CD 4 DIMMER PURE DIRECT DISPLAY @ A 5 1 2 3 4 5 6 7 8 9 ENTER CLEAR Some Yamaha amplifiers cannot be controlled with the p AMP key of this remote control. 5 DIMMER key Selects the brightness level for the front panel display.
A DISPLAY key Switches the time display. Each time you press the DISPLAY key during playback, the time display changes as follows: SHUFFLE key Performs shuffle playback. Notes • This operation is ineffective for MP3 or WMA discs. • The shuffle playback mode is cancelled when playback is stopped or the disc is ejected. 8 or B ENTER key Confirms a track number entered when you are programming tracks. key to (Play) key Starts playback.
Controls and functions ■ Program playback In the program playback mode, you can play back tracks in a programmed sequence. 1 Press PROGRAM while playback is stopped. This unit is set to the program editing mode. 2 Select a track by using the numeric buttons and press ENTER. 3 Repeat step 2 to program the next track. You can program up to 24 tracks. 4 Press the p (Play) key. Playback starts from the beginning of the programmed sequence.
■ Setting the DPLL (Digital Phased Lock Loop) bandwidth The audio DAC (ES9016) of this unit employs DPLL to generate accurate clock signals synchronized with the clock of the input digital audio signal. The 7-step DPLL bandwidth setting gives the unit tolerance for fluctuation of the clock of the input digital signal and adjustment of the accuracy of the operating clock in the DAC. 1 Press SOURCE to select the audio source to be played back.
Controls and functions ■ Installing batteries in the remote control 1 Remove the battery compartment cover. 2 Insert the two batteries (AAA, R03, UM-4) according to the polarity markings (+ and -) on the inside of the battery compartment. ■ Operating range of the remote control Approximately 6 m (20 ft) 30 30 1 2 y The remote control transmits a directional infrared beam. Be sure to aim the remote control directly at the remote control sensor on the front panel of this unit during operation.
Connections In this section, you will make connections between CD-S2100 and your amplifier.
CONNECTIONS Connections BALANCED OUT ANALOG OUT BALANCED OUT SYSTEM CONNECTOR GND REMOTE IN +HOT - COLD XLR balanced cable Stereo pin cable Amplifier If your amplifier is equipped with XLR balanced input jacks, we recommend balanced connection for optimum audio performance. When the SA-CD layer is played, the audio signals are output only from the BALANCED OUT and ANALOG OUT jacks.
CONNECTIONS USB OPTICAL COAXIAL OPTICAL DIGITAL IN COAXIAL DIGITAL OUT AC IN Optical digital cable Optical digital cable USB cable (Type B) PC Coaxial digital cable Component equipped with a digital output (PCM) jack Coaxial digital cable AV receiver equipped with a digital input jack Note Only PCM signals can be input to the DIGITAL IN (OPTICAL/COAXIAL) jacks of this unit. For details on the supported PCM signals, see page 26.
CONNECTIONS Connections ■ Connecting to the BALANCED OUT jacks Connect your amplifier with the XLR balanced input jacks. The pin assignments for these jacks are shown below. Refer to the owner’s manual supplied with your amplifier and verify that its XLR balanced input jacks are compatible with the pin assignments. 1: ground ■ Connecting the power cable Plug the power cable into the AC IN inlet when all connections are complete, and then plug in the power cable to the AC outlet.
CONNECTIONS ■ Operating this unit from another room If you connect an infrared receiver and transmitter to the REMOTE IN/OUT jacks of this unit, you can operate the unit and/or external component using the supplied remote control located in another room. Rear panel of CD-S2100 SYSTEM CONNECTOR When you have another Yamaha component supporting remote connection, as this unit does, an infrared transmitter is not necessary.
CONNECTIONS Playback of music files stored on a PC When a PC is connected to the USB jack of this unit, the unit functions as a USB DAC, enabling music files stored on the PC to be played via an amplifier connected to the unit. ■ Installing the dedicated driver Before connecting a PC to this unit, install the dedicated driver on the PC. 1 Rear panel of CD-S2100 Access the following URL, download the dedicated “Yamaha Steinberg USB Driver,” then extract and execute the file.
CONNECTIONS ■ Playing back music files stored on the PC 1 Connect the PC to this unit, using a USB cable. 2 Turn on the PC. 3 Turn this unit on by pressing the STANDBY/ ON, OFF switch on the front panel. 4 Select “USB,” using the SOURCE key. 5 Set the audio output destination of the PC to “Yamaha CD Player.
CONNECTIONS 24 En
Specifications In this section, you will find technical specifications for CD-S2100.
SPECIFICATIONS Specifications AUDIO SECTION GENERAL • Frequency Response (1 kHz, 0 dB) SA-CD ..................................................... 2 Hz to 50 kHz (–3 dB) CD ......................................................................... 2 Hz to 20 kHz • Power Supply [China, Korea, Asia, Australia, U.K. and Europe models] .......................................................... AC 220 – 240 V, 50/60 Hz [U.S.A, Canada and Taiwan models] .........................................................
SPECIFICATIONS Playable disc format ■ Supported disc types CD-R, CD-RW digital audio discs Super Audio CD Music CDs made by copying onto a CD-R or CD-RW (including MP3 or WMA format files). This unit is designed to play back compact discs bearing the marks shown below. Never attempt to load any other types of discs into this unit. This unit can also play back 8cm (3-inch) compact discs.
SPECIFICATIONS Playable disc format ■ About MP3 and WMA discs You can play back MP3 and WMA files recorded on a CD-R or CD-RW with similar uses as a music CD. MP3 MP3 (MPEG-1 Audio Layer-3) is a standard technology and format for compressing an audio sequence into a small-sized file. However, the original level of sound quality is preserved during playback. Notes • This unit plays back MP3 files in alphanumeric order.
SPECIFICATIONS Troubleshooting Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or if the instructions below do not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. Problem Cause Remedy See page This unit fails to turn on. The power cable is not connected nor completely connected. Securely connect the power cable.
SPECIFICATIONS Troubleshooting Problem Cause Remedy See page Noise from a nearby tuner. The tuner is too close to this unit. Move the tuner and this unit farther apart. Noise from inside of the disc tray. The disc may be warped. Replace the disc. No sound from the component connected to the DIGITAL IN (OPTICAL or COAXIAL) jack. The output audio source setting on the connected component is not “PCM.” Only PCM audio sources can be played via the DIGITAL IN (OPTICAL/COAXIAL) jacks of this unit.
SPECIFICATIONS ■ Messages on the information display Message Status NO DISC No disc is set on the disc tray. Check Cable The dedicated “Yamaha Steinberg USB Driver” has not been installed correctly. Or, the audio output of the computer has not been set to “Yamaha CD Player.” Check PC The audio signal from the computer cannot be recognized. Fs: ----kHz No audio signal is recognized.
AB Compact Disc Player OWNER’S MANUAL © 2014 Yamaha Corporation Printed in Malaysia ZK27080