English Français Compact Disc Player Lecteur Compact Disc CD-S303 EN FR Owner’s Manual Mode d’emploi
PRECAUTIONS Please read these precautions carefully before proceeding. Be sure to follow the instructions Please carefully read and observe the following precautions to avoid harm to people or damage to your personal property. After reading this document thoroughly, please retain it in a location that anyone using the product can access at any time. • Contact the following customer center for inspection or repair.
power switch is turned off, as long as the power cord is not unplugged from the wall AC outlet, the product is not disconnected from the power source completely. • If you plan not to use the product for a long period of time, remove the power cord plug from the AC outlets. Otherwise, fire or damage to the product may be caused. Do not disassemble • Do not modify or disassemble this product. Otherwise, fire, electrical shock, injury or damage to the product may be caused.
CAUTION These precautions alert you to the possibility of physical injury to yourself or others. Power supply • If the power cord plug inserted into the AC outlet is wiggly or loose, do not use that outlet. Otherwise, fire, electrical shock or burns may be caused. • When removing the power cord plug from the product or an outlet, always hold the plug itself and not the cord. Otherwise, the power cord may be damaged, resulting in fire or electrical shock.
Precautions for use NOTICE Follow the precautions below to avoid malfunction and damage to this product and to prevent the loss of data. Power supply • If you plan not to use this product for a long period of time, remove the power cord plug from the AC outlet. Even when [A] (Power) on the front panel is turned off, a small amount of current still flows through this product. Handling • Do not place any vinyl, plastic or rubber products on this product.
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
CONTENTS BEFORE USING THE UNIT 8 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 About this manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 APPENDIX 16 Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BEFORE USING THE UNIT Features About this manual • Optical digital output • This manual explains operations performed primarily on the supplied remote control. • Coaxial digital output • All illustrations in this manual are provided for the purpose of operational instruction. • Supports playback of CD-R and CD-RW discs • In this manual, a music CD is referred to as an audio CD, and a CD that contains MP3/WMA/AAC/WAV/FLAC data is referred to as a data CD.
Accessories • Remote control • Power cord • RCA stereo cable • Batteries (AA, R6, UM-3) (x2) • Owner’s Manual (this manual) Inserting batteries into the remote control Insert the batteries in the proper orientation. Batteries (AA, R6, UM-3) Remote control operating range Point the remote control toward the remote control sensor on the unit from within the range shown in the figure on the right.
PREPARATION Connecting to an amplifier Connecting the power cord After all the connections are complete, connect the supplied power cord to the AC IN connector on this unit, and then plug the other end into an AC outlet. CAUTION • Do not plug the power cord of this unit and other connected devices into AC outlets until all nonpower connections are complete.
Turning on the power To turn on the power to the unit, press A (Power) on the front panel. Power indicator A (Power) Note • If you press A (Power) on the remote control while the power to the unit is on, the unit will enter Standby mode. • The power indicator on the unit operates as follows: Brightly lit: Power is on Dimly lit: Standby mode Off: Power is off • This unit features an Auto Power Standby function that saves power consumption (page 19).
PLAYING AUDIO OPEN/CLOSE Playing an audio CD This unit enables you to play data CDs as well as audio CDs. For information on the type of CDs that can be played on this unit, please refer to “Supported file formats/discs/USB flash drives” (page 20). Numeric keys Use the following remote control keys to navigate the operation. Available keys 1 If the USB indicator on the front panel is lit, press CD/USB to switch to Disc mode. (Play) 2 Place a CD on the disc tray.
Playing music files stored on your USB flash drive You can play music files (stored on your USB flash drive) on this unit. For information on the supported USB flash drives, please refer to “Supported file formats/discs/USB flash drives” (page 20). 1 If the USB indicator on the front panel is off, press CD/USB to switch to USB mode. The USB indicator on the front panel lights up orange.
Advanced functions PROGRAM You can configure playback mode and display settings using advanced functions. RANDOM REPEAT Numeric keys Random-sequence playback Press RANDOM to play tracks in random order. Pressing RANDOM repeatedly will change the Random-sequence playback setting as follows: Indicator CLEAR ENTER Playing tracks in the specified order (Program playback) You can play audio CD tracks in the specified order. 1 Press PROGRAM while playback is stopped.
Playing a specified part repeatedly (A-B Repeat playback) A/B DISPLAY DIMMER You can specify the start and end points of a track during audio CD playback to play the specified part repeatedly. 1 2 • When the PURE DIRECT function is turned on: – The PURE DIRECT indicator lights up. Play an audio CD. Press A/B at the point you want to start Repeat playback.
APPENDIX Part names Front panel 8 1 2 3 0 A B C D E 0 Remote control sensor (page 9) 2 Power indicator (page 11) A (Skip backward/Search backward) (pages 12, 13) 3 USB jack (page 13) B (Skip forward/Search forward) (pages 12, 13) 4 USB indicator (page 13) C (Play) (pages 12, 13, 14) 5 CD/USB (pages 12, 13) D (Pause) (pages 12, 13) 6 PURE DIRECT (page 15) E (Stop) (pages 12, 13, 14, 15) 8 Disc tray (page 12) 9 En 6 7 1 A (Power) (page 11) 7 PURE DIRECT indicator (page 15) 16 4
Display 1 2 3 4 5 6 CD TEXT AAC WAV FLAC RESUM RDY TRACK TOTAL REMAIN PROG RNDM REP FOLDER ALL A - B 1 / (Play/Pause) indicator (pages 12, 13) 4 Time indicator (page 15) 2 Playback media indicator (pages 12, 13) 5 Playback mode indicator (pages 14, 15) 3 Advanced setting indicator (page 19) 6 Information display (pages 14, 15, 19) Rear panel 1 2 1 ANALOG OUT jacks (page 10) 3 4 4 AC IN connector (page 10) 2 DIGITAL OUT jack (COAXIAL) (page 10) 3 DIGITAL OUT jack (OPTICAL) (page 10) En
Remote control 2 1 1 A (Power) (page 11) 2 Remote control signal transmitter (page 9) 3 4 5 6 3 OPEN/CLOSE (page 12) 7 8 9 4 PROGRAM (page 14) 5 REPEAT (page 14) 6 DIMMER (page 15) 7 RANDOM (page 14) 0 8 A/B (page 15) 9 DISPLAY (page 15) 0 Numeric keys (pages 12, 14) A B A CLEAR (page 14) B ENTER (page 14) C C (Search backward), (Search forward) (pages 12, 13) (Pause) (pages 12, 13) (Skip backward) (pages 12, 13) (Skip forward) (pages 12, 13) (Play) (pages 12, 13, 14) D E (Stop) (pages 12, 1
Advanced settings This section explains how to configure various advanced functions. You can configure most of these settings from the front panel. (Some settings require remote control operation.) Playback Mode Memory (PLAY MEM) With this function enabled, the unit retains the Repeat playback and Random-sequence playback settings even after the power to the unit is turned off. When the Playback Mode Memory function is turned on, the Advanced setting indicator (RESUM) on the display lights up.
Supported file formats/discs/USB flash drives ❑ Supported file formats File ❑ Supported discs Sampling frequency (kHz) Bit depth (bit) Bitrate (kbps) Number of channels MP3 32/44.1/48 — 32-320 2 WMA 32/44.1/48 — 48-192 2 AAC 32/44.1/48 — 8-320 2 WAV * 32/44.1/48/64/88.2/96 16/24 — 2 FLAC 32/44.1/48/64/88.2/96 16/24 — 2 Please use discs with the following logos.
❑ Handling a disc • Handle a disc carefully so as not to scratch the recorded surface. Do not bend a disc. Specifications The specifications of this unit are as follows. Output jacks • If there are any fingerprints or dust on the recorded surface, use a soft cloth to wipe the surface straight from the center toward the perimeter. • Analog audio x 1 (RCA Unbalanced) Other jacks • USB × 1 (USB2.0) • Digital audio COAXIAL x 1, OPTICAL x 1 Audio section • Output Level (1 kHz, 0 dB, Fs 44.1 kHz) ..........
Troubleshooting Refer to the table below if the unit fails to function properly. If your problem is not listed below, or if the symptoms persist after you follow the instructions below, turn off the power to the unit by pressing A (Power) on the front panel, disconnect the power cord, and contact your nearest authorized Yamaha dealer or service center. Problem Cause Solution Page Pressing the power switch does not turn the power on. The power cord may not be properly plugged in.
Problem Cause Solution Page Buzzing or hum noise is heard. The RCA stereo cable is not connected firmly. Connect the RCA stereo cable firmly. If the symptom does not improve, check to see whether the cable itself is defective. 10 Noise in the tuner The unit is located close to the tuner. Relocate the unit farther away from the tuner, or turn off the power to the unit. — The disc tray is making noise. The disc is deformed. Use a non-deformed disc.
PRÉCAUTIONS D’USAGE Lisez attentivement ces consignes avant l’utilisation du produit. Assurez-vous de suivre les instructions Lisez attentivement et observez les précautions suivantes pour éviter les blessures corporelles et les dommages de biens personnels. Après avoir lu ce document dans son intégralité, rangez-le dans un lieu accessible en permanence à tout utilisateur du produit. • Pour tout travail d’inspection ou de réparation, adressez-vous à un des centres de service clientèle suivants.
• Vérifiez régulièrement l’état de la fiche du cordon d’alimentation et dépoussiérez-la en prenant soin de retirer toutes les impuretés qui pourraient s’y accumuler. Sinon, vous risquez un incendie ou un choc électrique. • Veillez à insérer à fond la fiche du cordon d’alimentation dans la prise secteur. Sinon, cela pourrait causer un court-circuit provoquant un choc électrique, un incendie ou un endommagement du produit.
Sinon, les piles pourraient exploser ou du liquide pourrait en fuir, causant un incendie, des brûlures, une perte de la vue ou un endommagement du produit. Si vous touchez du liquide fuyant d’une pile, rincez-le immédiatement à l’eau et consultez un médecin. • Ne transportez pas les piles dans une poche ni un sac et ne les rangez pas avec tout objet métallique.
Sinon, cela pourrait causer une perte auditive, un choc électrique ou un endommagement du produit. • Quand vous mettez votre système audio sous tension, veillez à toujours mettre l’amplificateur de puissance sous tension EN DERNIER. Quand vous mettez votre système audio hors tension, veillez à toujours mettre l’amplificateur de puissance hors tension EN PREMIER. Sinon, cela pourrait causer une perte auditive ou un endommagement du produit.
Informations importantes NOTE Cette section décrit des précautions à observer durant l’utilisation, des restrictions de fonctionnalité et des informations complémentaires utiles. Mise au rebut ou transfert • Avant de transférer la propriété de ce produit, veillez à inclure ce document et les accessoires fournis avec le produit. • Suivez les règlements en vigueur dans votre région pour mettre au rebut ce produit et ses accessoires.
Sommaire AVANT D’UTILISER L’APPAREIL 30 Fonctionnalités . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 À propos de ce manuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Accessoires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 ANNEXE 38 Noms des éléments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AVANT D’UTILISER L’APPAREIL Fonctionnalités • Sortie numérique optique • Sortie numérique coaxiale • Lecture de disques CD-R et CD-RW prise en charge • Lecture de fichiers sauvegardés sur clé USB ou CD de données (MP3/WMA/AAC/ WAV/FLAC) • Lecture en ordre aléatoire (page 36) • Lecture répétée (page 36) À propos de ce manuel • Ce manuel décrit les opérations exécutées principalement avec la télécommande fournie.
Accessoires • Télécommande • Cordon d’alimentation • Câble stéréo RCA/Cinch • Piles (AA, R6, UM-3) (x2) • Mode d’emploi (ce manuel) Mise en place des piles dans la télécommande Insérez les piles dans le sens correct. Piles (AA, R6, UM-3) Portée de la télécommande Pointez la télécommande vers le capteur de télécommande de l’appareil, en l’utilisant dans sa zone de portée décrite sur l’illustration de droite.
PRÉPARATION Connexion à un amplificateur Raccordement du cordon d’alimentation Quand toutes les connexions sont effectuées, branchez le cordon d’alimentation fourni à la prise AC IN de l’appareil et l’autre extrémité du cordon à une prise de courant de tension appropriée. ATTENTION • Ne branchez le cordon d’alimentation ni de cet appareil ni d’aucun autre dispositif au secteur avant que toutes les connexions audio ne soient terminées.
Mise sous tension Pour mettre l’appareil sous tension, appuyez sur le bouton A (alimentation) du panneau avant. Témoin d’alimentation A (alimentation) Note • Si vous appuyez sur la touche A (alimentation) de la télécommande quand l’appareil est sous tension, il passe en veille.
LECTURE AUDIO OPEN/CLOSE Lecture de CD audio Cet appareil permet de lire des CD de données et des CD audio. Pour des informations sur les types de CD pouvant être lus avec cet appareil, voyez la section «Formats de fichiers/disques/clés USB compatibles» (page 42). Touches numériques 1 2 (lecture) Insérez un CD dans le tiroir de disque. (pause) Le témoin de pause ( ) s’allume sur l’écran et la lecture s’interrompt. Appuyez sur (ou à nouveau sur ) pour relancer la lecture.
Lecture de fichiers musicaux stockés sur une clé USB Cet appareil permet de lire des fichiers musicaux (stockés sur une clé USB). Pour des informations sur les clés USB prises en charge, voyez la section «Formats de fichiers/disques/clés USB compatibles» (page 42). 1 Si le témoin USB du panneau avant est éteint, appuyez sur la touche CD/USB pour activer le mode USB. Le témoin USB en face avant s’allume en orange.
Fonctions avancées PROGRAM Vous pouvez configurer le mode de lecture et les paramètres d’affichage à l’aide des fonctions avancées. RANDOM REPEAT Touches numériques CLEAR ENTER Lecture en ordre aléatoire Lecture des plages selon un ordre défini (lecture programmée) Vous pouvez lire les plages d’un CD selon un ordre défini. Appuyez sur la touche RANDOM pour lire les plages dans un ordre aléatoire.
Lecture répétée d’un passage spécifique (lecture répétée A-B) A/B DISPLAY DIMMER Vous pouvez définir le point de départ et de fin d’un passage sur une plage de CD audio de sorte à lire ce passage de manière répétée. 1 2 • Quand la fonction PURE DIRECT est active : – Le témoin PURE DIRECT s’allume. – L’écran est éteint pendant la lecture de contenu. Lisez un CD audio. – Il affiche un nombre minimum de témoins et messages durant l’utilisation de l’appareil.
ANNEXE Noms des éléments Panneau avant 8 1 2 3 0 A B 0 Capteur de télécommande (page 31) 2 Témoin d’alimentation (page 33) A 3 Prise USB (page 35) B 4 Témoin USB (page 35) C (lecture) (pages 34, 35, 36) 5 CD/USB (pages 34, 35) D (pause) (pages 34, 35) 6 PURE DIRECT (page 37) E (arrêt) (pages 34, 35, 36, 37) 8 Tiroir de disque (page 34) 9 Fr 6 7 1 A (alimentation) (page 33) 7 Témoin PURE DIRECT (page 37) 38 4 5 9 (ouverture/fermeture) (page 34) C D E (saut arrière/recherche ar
Écran 1 2 3 4 5 6 CD TEXT AAC WAV FLAC RESUM RDY TRACK TOTAL REMAIN PROG RNDM REP FOLDER ALL A - B 1 Témoin / (lecture/pause) (pages 34, 35) 4 Affichage de durée (Page 37) 2 Témoin de support de lecture (pages 34, 35) 5 Témoin du mode de lecture (pages 36, 37) 3 Témoin des réglages avancés (page 41) 6 Affichage d’informations (pages 36, 37, 41) Panneau arrière 1 2 1 Prises ANALOG OUT (page 32) 3 4 4 Prise AC IN (page 32) 2 Prise DIGITAL OUT (COAXIAL) (page 32) 3 Prise DIGITAL OUT (OPTIC
Télécommande 2 1 1 A (alimentation) (page 33) 2 Émetteur de signal de télécommande (page 31) 3 4 5 6 3 OPEN/CLOSE (page 34) 7 8 9 4 PROGRAM (page 36) 5 REPEAT (page 36) 6 DIMMER (page 37) 7 RANDOM (page 36) 0 8 A/B (page 37) 9 DISPLAY (page 37) 0 Touches numériques (pages 34, 36) A B A CLEAR (page 36) B ENTER (page 36) C C (recherche arrière), (recherche avant) (pages 34, 35) (pause) (pages 34, 35) (saut arrière) (pages 34, 35) (saut avant) (pages 34, 35) (lecture) (pages 34, 35, 36) D E (ar
Réglages avancés Cette section décrit la configuration des diverses fonctions avancées. Vous pouvez changer la majorité de ces paramètres depuis la face avant. (Certains paramètres ne sont accessibles que via la télécommande.) Mémorisation du mode de lecture (PLAY MEM) Quand cette fonction est active, l’appareil mémorise et conserve les réglages de lecture répétée et de lecture aléatoire après sa mise hors tension.
Formats de fichiers/disques/clés USB compatibles ❑ Formats de fichiers compatibles Fichier ❑ Disques pris en charge Fréquence d’échantillonnage (kHz) Résolution de bit (bit) Débit binaire (kbps) Nombre de canaux MP3 32/44.1/48 — 32-320 2 WMA 32/44.1/48 — 48-192 2 AAC 32/44.1/48 — 8-320 2 WAV * 32/44.1/48/64/88.2/96 16/24 — 2 FLAC 32/44.1/48/64/88.2/96 16/24 — 2 Utilisez des disques affichant un des logos suivants.
❑ Manipulation des disques • Manipulez les disques avec soin, de sorte à ne pas rayer leur surface enregistrée. Ne pliez jamais les disques. Caractéristiques techniques Voici les caractéristiques techniques de cet appareil. Prises de sortie • En présence de traces de doigts ou de poussière sur la surface enregistrée, frottez le disque depuis son centre vers son bord extérieur avec un chiffon doux. • Audio analogique x 1 (RCA/Cinch asymétrique) Autres prises • USB × 1 (USB2.
Résolution des problèmes Reportez-vous au tableau suivant si l’appareil ne fonctionne pas correctement. Si l’anomalie constatée ne figure pas ci-dessous, ou si la correction suggérée reste sans effet, mettez l’appareil hors tension en appuyant sur A (alimentation) en face avant, débranchez le cordon d’alimentation et prenez contact avec un revendeur ou un centre SAV Yamaha agréé. Anomalies Page Le cordon d’alimentation est peut-être mal raccordé.
Anomalies Causes possibles Solution Page Des vibrations ou des coups affectent la lecture. Changez l’emplacement de l’appareil. — Le disque est sale ou rayé. Éliminez la saleté de la surface du disque ou choisissez un disque intact. 43 L’appareil produit un ronflement ou un bourdonnement. Le câble RCA/Cinch stéréo est mal raccordé. Raccordez fermement le câble RCA/Cinch stéréo. Si cela ne résout pas le problème, assurez-vous que le câble n’est pas lui-même endommagé.
Software licenses This product uses the following software. Licences de logiciel Ce produit utilise le logiciel suivant. FLAC Copyright © 2000–2009 Josh Coalson Copyright © 2011–2021 Xiph.Org Foundation Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: - Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
Yamaha Global Site https://www.yamaha.com/ Yamaha Downloads https://download.yamaha.