User Manual

131
General Specifications
0 dBu is referenced to 0.775 Vrms.
*1 Power rating (120 V, 25°C). This is total value of individual output power.
This value is measured by releasing the software protection.
Dynamic: Total peak power of individual outputs. Measured at minimum load impedance, with protection released.
Continuous: Measured at nominal impedance, with protection activated.
General DHR15 DHR12M DHR10
System Type 2-way, Bi-amp Powered Speaker, Bass-reflex Type
Frequency Range (-10 dB) 44 Hz–20 kHz 55 Hz–20 kHz 52 Hz–20 kHz
Coverage Angle H90° × V60° H90° × V90° H90° × V60° (Rotatable)
Crossover Type FIR-X tuning (Linear Phase FIR Filter)
Crossover Frequency 1.8 kHz 1.8 kHz 1.9 kHz
Measured Maximum SPL (Peak)
IEC noise@1m
131 dB SPL 129 dB SPL 128 dB SPL
Transducer DHR15 DHR12M DHR10
LF Diameter 15" Cone 12" Cone 10" Cone
Voice coil 2.5" 2.5" 2"
Magnet Ferrite
HF Diaphragm 1.4" 1.75" 1.4"
Type
1" Throat Compression Driver
1" Throat Compression Driver
Coaxial
1" Throat Compression Driver
Magnet Ferrite
Enclosure DHR15 DHR12M DHR10
Material, Color Plywood, Black, Polyurea coating
Floor Monitor Angle — 57° —
Dimensions (W×H×D, with rubber feet) 432 × 692 × 405 mm 500 × 343 × 454 mm 305 × 494 × 300 mm
Net Weight 24.0 kg 16.5 kg 15.0 kg
Handles Side × 2 Side × 1 Top × 1
Pole Socket 35 mm × 2 (0 and 7 degree) 35 mm 35 mm
Rigging Points Top × 2, Rear × 1
(Fit for M10 Eyebolts)
—
Top × 2, Rear × 1
(Fit for M10 Eyebolts)
Optional Speaker Bracket — — UB-DXRDHR10
Amplifier DHR15 DHR12M DHR10
Amplifier Type Class-D
Power Rating
*1
Dynamic 1000 W (LF: 800 W, HF: 200 W) 700 W (LF: 500 W, HF: 200 W)
Continuous 465 W (LF: 400 W, HF: 65 W) 325 W (LF: 260 W, HF: 65 W)
Cooling Fan Cooling, 4 Speeds.
AD/DA 24 bit 48 kHz Sampling
HPF OFF, 100 Hz, 120 Hz, 24 dB/Oct.
DSP Preset D-CONTOUR: FOH/MAIN, MONITOR, OFF
Protection Speaker Clip Limiting, Integral Power Protection, DC-fault
Amplifier Thermal, Output Over Current
Power Supply Thermal, Output Over Voltage, Output Over Current
Connectors Input Input1: Combo × 1, Input2: Combo × 1, RCA PIN × 2 (Unbalanced)
Output Output: XLR3-32 × 1 (CH1 Parallel Through or CH1+CH2 Mix)
Input Impedance INPUT1: LINE: 10 kΩ, MIC: 3 kΩ, INPUT2: 10 kΩ
Input Sensitivity (LEVEL: Maximum) INPUT1: LINE: 0 dBu, MIC: -32 dBu, INPUT2: 0 dBu
Input Sensitivity (LEVEL: Center) INPUT1: LINE: +10 dBu, MIC: -22 dBu, INPUT2: +10 dBu
Maximum Input Level INPUT1: LINE: +24 dBu, MIC: -8 dBu, INPUT2: +24 dBu
Controls LEVEL × 2, LINE/MIC, HPF, D-CONTOUR, THRU/MIX, POWER
Idle Power Consumption 18 W 18 W
1/8 Power Consumption 74 W 60 W
Power Requirements 100 V, 110–120 V, 220–240 V, 110 V/127 V/220 V (Brazil), 50/60 Hz
General Specifications (English only)