User Manual
Table Of Contents
- Hinweise zur Verwendung dieses Referenzhandbuchs
- Inhaltsverzeichnis
- Funktionsschema
- SELECTED-CHANNEL-Bereich
- Centralogic-Bereich
- Routing der Ein- und Ausgänge
- Eingangskanäle
- Signalfluss für Eingangskanäle
- Kanalname und -symbol festlegen
- HA-Einstellungen (Eingangsverstärker)
- Senden eines Signals von einem Eingangskanal zum STEREO/MONO-Bus
- Hinzugefügte Pan-Funktion (nur für monaurale Eingangskanäle)
- Senden eines Signals von einem Eingangskanal an einen MIX-/MATRIX-Bus
- Kanalnamenanzeige
- Korrigieren der Eingangsverzögerung zwischen Kanälen (Input Delay)
- Surround-Ausgang für Eingangskanäle
- Bedienungsvorgänge für die Kanal-Library
- OUTPUT-Kanäle
- EQ und Dynamik
- Channel Job
- Szenenspeicher
- Speichern und Aufrufen von Szenen
- Szenenspeicher bearbeiten
- Einsatz der Funktion „Global Paste“ (Globales Einfügen)
- Verwenden der Focus Recall-Funktion
- Verwenden der Fade-Funktion
- Ausgabe eines Steuersignals an ein externes Gerät in Kombination mit einem Szenen-Abruf (GPI OUT)
- Wiedergeben einer mit einem Szenenabruf verknüpften Audiodatei
- Verwenden des Preview-Modus (Vorschau)
- Monitor- und Cue-Funktionen
- Talkback und Oszillator
- Pegelanzeigen
- Grafischer EQ, Parametrischer EQ, Effekte und PREMIUM RACK
- I/O-Geräte und externe Eingangsverstärker
- MIDI
- Recorder
- Informationen zum USB-Recorder
- Zuweisen von Kanälen zu den Ein-/Ausgängen des Recorders
- Audio-Aufnahme auf einem USB-Stick
- Wiedergabe von Audiodateien von einem USB- Flash-Laufwerk
- Bearbeiten der Titelliste
- Aufnahme und Wiedergabe mit Hilfe von DAWSoftware auf dem Computer
- Verwenden des CL-Pults mit Nuendo Live
- Setup (Einrichtung)
- Der SETUP-Bildschirm
- Benutzereinstellungen
- Einstellungen
- USER-DEFINED-Tasten
- Funktionen, die USER-DEFINED-Tasten zugewiesen werden können
- USER-DEFINED-Drehregler
- Funktionen, die USER-DEFINED-Drehreglern zugewiesen werden können
- Zuweisbare Encoder
- Funktionen, die zuweisbaren Encodern zugewiesen werden können
- Funktionen für die GAIN/PAN/ASSIGN-Drehregler (zuweisbare Encoder)
- Custom-Fader-Bank
- Master-Fader
- Funktionen für die Custom-Fader-Bank
- Pultsperre
- Speichern und Laden von Setup-Daten auf und von einem USB-Flash-Laufwerk
- Formatieren eines USB-Flash-Laufwerks
- Hinzugefügte Funktion zum erneuten Mounten von USB-Flash-Laufwerken
- Wordclock- und Slot-Einstellungen
- Verwenden von Kaskadenverbindungen
- Grundlegende Einstellungen für MIX-Busse und MATRIX-Busse
- Ein-/Ausschalten der gesamten Phantomspannungsversorgung
- Einstellen der Helligkeit des Touchscreens, der LEDs, der Kanalnamen-Displays und der Pultbeleuchtung
- Datum und Uhrzeit der eingebauten Uhr einstellen
- Einstellen der Netzwerkadresse
- Dante-Audionetzwerk-Einstellungen
- Verwenden des GPI (General Purpose Interface)
- Hilfefunktion
- Sonstige Funktionen
- Initialisieren des Geräts auf die Werksvoreinstellungen
- Einstellen des Ablesepunkts des Touchscreens (Kalibrierungsfunktion)
- Einstellen der Fader (Kalibrierungsfunktion)
- Feineinstellen der Ein-/Ausgangsverstärkung (Kalibrierungsfunktion)
- Einstellen der Kanalfarbe (Kalibrierungsfunktion)
- Einstellen der Helligkeit des Kanalnamen-Displays
- Einstellen des Kontrasts des Kanalnamen-Displays
- Initialisieren der Pulteinstellungen und des Dante- Audionetzwerks
- Geänderte Vorgehensweise beim Aktualisieren von NAME-SUB-CPU-Firmware
- Hinzugefügte Aktualisierungsfunktion für Dante- Firmware
- Warn- und Fehlermeldungen
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/output characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Data List
20
M.BAND COMP
Two input, two output 3-band compressor, with individual solo and gain reduction metering for
each band.
Premium Rack Processor Parameters
Portico5033
This models an analog 5-band EQ made by the RND company.
Portico5043
This models an analog compressor/limiter made by the RND company.
LIM.ATK 0-120 ms Attack time of the limiter
LIM.REL
*1
Release time of the limiter
LIM.KNEE 0-5 Knee of the limiter
LIM.BYP OFF/ON Bypasses the limiter
PRESENCE -10 to +10
Positive (+) values lower the threshold of the high band and raise the
threshold of the low band. Negative (-) values do the opposite. If this is
set to 0, the high, mid, and low bands will be affected in the same way.
LOOKUP 0.0-100.0 ms Lookup delay
MAKE UP OFF/ON Automatically adjusts the output level
*1. 6.0 ms-46.0 s (fs=44.1 kHz), 5.0 ms-42.3 s (fs=48 kHz)
Parameter Range Description
L-M XOVER 21.2 Hz-8.00 kHz Crossover frequency between the low and mid bands
M-H XOVER 21.2 Hz-8.00 kHz Crossover frequency between the mid and high bands
SLOPE -6 dB, -12 dB Filter slope
LOW GAIN -12.0 dB to +12.0 dB Low band gain
MID GAIN -12.0 dB to +12.0 dB Mid band gain
HI. GAIN -12.0 dB to +12.0 dB High band gain
TOTAL -72.0 dB to +12.0 dB Overall gain
CEILING -6.0 dB to 0.0 dB, OFF Restricts the output so that it will not exceed the specified level
LOW THRE -54.0 dB to 0.0 dB Threshold of the low band compressor
LOW RAT 1:1 to 20:1 Ratio of the low band compressor
LOW ATK 0-120 ms Attack time of the low band compressor
LOW REL
*1
*1. 6.0 ms-46.0 s (fs=44.1 kHz), 5.0 ms-42.3 s (fs=48 kHz)
Release time of the low band compressor
LOW KNEE 0-5 Knee of the low band compressor
LOW BYP OFF/ON Bypasses the low band compressor
MID THRE -54.0 dB to 0.0 dB Threshold of the mid band compressor
MID RAT 1:1 to 20:1 Ratio of the mid band compressor
MID ATK 0-120 ms Attack time of the mid band compressor
MID REL
*1
Release time of the mid band compressor
MID KNEE 0-5 Knee of the mid band compressor
MID BYP OFF/ON Bypasses the mid band compressor
HI. THRE -54.0 dB to 0.0 dB Threshold of the high band compressor
HI. RAT 1:1 to 20:1 Ratio of the high band compressor
HI. ATK 0-120 ms Attack time of the high band compressor
HI. RAT
*1
Release time of the high band compressor
HI. KNEE 0-5 Knee of the high band compressor
HI. BYP OFF/ON Bypasses the high band compressor
LOOKUP 0.0-100.0 ms Lookup delay
MAKE UP OFF/ON Automatically adjusts the output level
Parameter Range Description
Parameter Range Description
ALL BYPASS OFF, ON
Turns bypass on/off for the EQ. Even in the bypassed state, the signal will
pass through the input/output transformers and the amp circuit.
TRIM -12.0 to 12.0 dB Input gain
LF FREQ 30.00 to 300.0 Hz Center frequency of the LF band
LF GAIN -12.0 to 12.0 dB Gain of the LF band
LMF IN OFF, ON Switches the LMF band on/off
LMF Q 0.70 to 5.00 Q of the LMF band
LMF FREQ 50.00 to 400.0 Hz Center frequency of the LMF band
LMF GAIN -12.0 to 12.0 dB Gain of the LMF band
MF IN OFF, ON Switches the MF band on/off
MF Q 0.70 to 5.00 Q of the MF band
MF FREQ 330.0 to 2500 Hz Center frequency of the MF band
MF GAIN -12.0 to 12.0 dB Gain of the MF band
HMF IN OFF, ON Switches the HMF band on/off
HMF Q 0.70 to 5.00 Q of the HMF band
HMF FREQ 1.80k to 16.0k Hz Center frequency of the HMF band
HMF GAIN -12.0 to 12.0 dB Gain of the HMF band
LF/HF IN OFF, ON Switches the LF/HF bands on/off
HF FREQ 2.50k to 25.0k Hz Center frequency of the HF band
HF GAIN -12.0 to 12.0 dB Gain of the HF band
Parameter Range Description
IN OFF, ON
Turns bypass on/off for the compressor. When bypassed, the button will
be unlit. However even in the bypassed state, the signal will pass through
the input/output transformers and the amp circuit.
FB OFF, ON Switches between feed-forward type and feed-back type
THRESHOLD -50.0 to 0.0 dB Threshold level
RATIO 1.10 : 1 to 28.9 : 1, LIMIT Compression ratio
ATTACK 20 to 75 ms Attack time
RELEASE 100 ms to 2.50 sec Release time
GAIN -6.0 to 20.0 dB Output level