User Manual
Table Of Contents
- How to Use This Reference Manual
- Table of contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Warning/Error Messages
- Index
- Data List
- Table of Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/output characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Setup
Reference Manual
196
• STORE CONFIRMATION
• RECALL CONFIRMATION
If these ON buttons are lit, a confirmation message will appear when you perform a
Store or Recall operation respectively.
2 PATCH field
Enables you to turn on or off options related to patch operations.
• PATCH CONFIRMATION
If this ON button is lit, a confirmation message will appear when you edit an input patch
or output patch.
• STEAL PATCH CONFIRMATION
If this ON button is lit, a confirmation message will appear when you edit an input or
output patch item that is already patched to a port.
3 LOCALE SETUP field
Enables you to select the language used in Help files. Select “EN” to display Help files in
English.
4 ERROR MESSAGE field
Enables you to specify whether certain error messages should be displayed.
• DIGITAL I/O ERROR
If this is on, an error message will appear when a digital audio I/O error occurs.
• MIDI I/O ERROR
If this is on, an error message will appear when a MIDI I/O error occurs.
5 PANEL OPERATION field
Enables you to make settings for options related to panel operation.
• AUTO CHANNEL SELECT
Specifies whether the corresponding channel will be selected when you operate the
[ON] key or fader for the channel. You can set this parameter separately for INPUT (input
channels) and OUTPUT (output channels).
•[CUE][SEL] LINK
Specifies whether channel selection will be linked with cue operations. If the LINK
button is on, channels for which cue operations were performed will be selected.
•[FADER BANK][SEL] LINK
Specifies whether channel selection will be linked with fader bank selection. You can set
this parameter separately for INPUT (input channels), OUTPUT (output channels), and
CUSTOM (Custom fader bank).
If the LINK button is on, and you select the corresponding fader bank, the channel in
that bank that was selected most recently will be selected, and its [SEL] key will light.
• IDENTIFY I/O RACK PORT BY [SEL]
Specifies whether to enable a function that allows you to identify the I/O device port
connected to a channel by pressing the [SEL] key for that channel.
If this ON button is lit, pressing a [SEL] key on the panel will cause the signal indicator
to flash for the port of the I/O device that is assigned to the corresponding channel by
the INPUT PATCH/OUTPUT PATCH settings.
• POPUP APPEARS WHEN KNOB(S) PRESSED
Specifies whether pressing a knob in the SELECTED CHANNEL section of the panel while
the SELECTED CHANNEL VIEW screen is displayed will cause a window (1ch) to appear.
If the ON button is lit, a window (1ch) will open (or close) whenever you press a knob.
NOTE
If you press the SEND or PAN knob, a window (8ch) will open.
• GAIN KNOB FUNCTION
Specifies what will happen when you operate the GAIN knob in the SELECTED
CHANNEL section on the panel. When ANALOG GAIN button is lit, you can adjust
analog gain on the head amp. When DIGITAL GAIN button is lit, you can adjust digital
gain on the console.
•SCENE UP/DOWN
Specifies what the SCENE MEMORY [INC]/[DEC] keys will do when pressed in the
SCENE windows.
When the SCENE +1/-1 button is lit, pressing the [INC] or [DEC] key will increment or
decrement the scene number.
When the LIST UP/DOWN button is lit, pressing the [INC] or [DEC] key will scroll the list
upward or downward.
• LIST ORDER
Specifies the order in which scene memories and library items will appear on the list.
When the NORMAL button is lit, the list appears in ascending numerical order. When
the REVERSE button is lit, the list appears in descending numerical order.
•NAME DISPLAY
Specifies the content of the name display in the Channel Strip section.
When the NAME ONLY button is lit, the channel name and the channel number appear.
Select GR METER to display the GR meter and fader level value.
Select ENCODER INFO to display the information of a function that has been assigned
to the GAIN/PAN/ASSIGN knob on the channel fader strip. This option is the same as
the FULL FUNCTION option in CL version 1.7 or earlier.
NOTE
• You can now view the gain reduction meter for DYNAMICS 1 and 2, as well as other information,
on the channel name display.
• In addition, if a channel is off during SENDS ON FADER mode, the channel name display will be
highlighted.
• The GR meters function enables you to easily view the movement of the gain reduction.