User Manual
Table Of Contents
- How to Use This Reference Manual
- Table of contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Warning/Error Messages
- Index
- Data List
- Table of Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/output characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Setup
Reference Manual
202
SENDS ON
FADER
MIX1-MIX24
NORMAL/WITH CUE
This function switches between the normal
function on/off (NORMAL), and the function
with cue on/off (WITH CUE). With the WITH
CUE option, cue will be enabled if SENDS ON
FADER mode is engaged or if you switch mode
during SENDS ON FADER mode. Also, with the
WITH CUE option, cue for all output channels
will be canceled if SENDS ON FADER mode is
disengaged.
MTRX 1-MTRX 8
MIX ON FADER
MATRIX ON FADER
SENDS ON FADER
SET BY SEL
+48V
-
Hold down this key and press SEL to switch it
on/off.
During this time, the [SEL] LED will be lit if on or
dark if off.
If SET [PRE SEND] is selected, “SEND ON
FADER” mode is engaged while you are holding
down the [SEL] key.
It goes OFF when the bank is switched.
Ø
INSERT ON
DIRECT OUT ON
PRE SEND
TO STEREO
TO MONO
TO LCR
GAIN COMPENSATION
SET DEFAULT
VALUE
--
Press and hold this key, and then press any of
the following knobs on the panel to reset that
knob to its default value: a knob in the
SELECTED CHANNEL section, a knob in the
SELECTED CHANNEL VIEW screen, or a knob in
the Centralogic section.
It goes OFF when the bank is switched.
SET NOMI-
NAL VALUE
--
While holding down this key, press a [SEL] key
to set the fader of that channel to nominal level.
You can also push a knob in the SEND field of
the SELECTED CHANNEL VIEW screen to set the
send level to nominal level.
It goes OFF when the bank is switched.
SURROUND
PAN
L ON
*5)
In Surround mode, this is used to switch the bus
assign on and off for the channel selected in list
5).
R ON
C ON
LFE ON
Ls ON
Rs ON
SURROUND
PAN
PANNING L
*5)
In Surround mode, this is used to set hard
panning for the channel selected in list 5).
PANNING R
PANNING Front Center
PANNING Ls
PANNING Rs
PANNING Back
PANNING Side L
*5)
In Surround mode, this is used to set hard
panning for the channel selected in list 5).
PANNING Side R
PANNING Center
FUNCTION
PARAMETER 1 PARAMETER 2 Description
SURROUND
PAN
PANNING TOGGLE *5)
In Surround mode, this is used to toggle the
settings for hard panning for the channel
selected in list 5).
With each press, the setting is toggled in the
following order: Center L Front Center R
Side R Rs Back, Ls Side L (Center).
TALKBACK
TALKBACK ON
LATCH Switch TALKBACK on/off.
UNLATCH
Turn TALKBACK on while pressed.
It goes OFF when the bank is switched.
SELECTED CH ASSIGN -
While holding down this key, press a SEL key of
an OUTPUT channel to switch the assignment
on/off. During this time, the [SEL] LED will be lit
if assign is ON, or dark if OFF.
The assignment setting made while holding
down this key will be stored. Pressing the key
again will recall the stored setting. Settings can
be stored in multiple keys to facilitate rapid
assignment switching.
It goes OFF when the bank is switched.
DIRECT ASSIGN *3)
The operations performed when this key is
pressed are as follows.
- Toggle assignment of channel selected in list
3) ON and OFF.
At this time, the LED display is as shown below.
- If the channel is assigned, the LED will be on.
Otherwise, the LED will be off.
TALKBACK
DIRECT ASSIGN WITH
ON
*3)
The operations performed when this key is
pressed are as follows.
- Assignments other than for the channel
selected in list 3) are removed.
- If a channel is assigned and TALKBACK is ON
at the same time, TALKBACK is turned OFF
and the channel assignment is removed.
- Otherwise, TALKBACK will be ON and the
channel assignment will be ON.
At this time, the LED display is as shown below.
- If the channel is assigned and TALKBACK is ON
at the same time, the LED will be on.
- Otherwise, the LED will be off.
TAP TEMPO
CURRENT PAGE -
Use the tap tempo function in the displayed
screen.
EFFECT RACK1-8
WITH POPUP
Use the tap tempo function for the specified
effect. If WITH POPUP is selected, the Tap
Tempo screen is displayed. If WITHOUT POPUP
is selected, the Tap Tempo screen is not
displayed.
WITHOUT POPUP
FUNCTION
PARAMETER 1 PARAMETER 2 Description