User Manual
Table Of Contents
- How to Use This Reference Manual
- Table of contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Warning/Error Messages
- Index
- Data List
- Table of Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/output characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Setup
Reference Manual
204
NOTE
• If you are logged-in as the Administrator, you can also turn on the FOR GUEST button to access
the USER DEFINED KNOBS and ASSIGNABLE ENCODER for Guest page and make USER
DEFINED knob settings for the Guest account.
• The 4 knobs in the USER DEFINED KNOBS and ASSIGNABLE ENCODER page correspond to
USER DEFINED knobs [1]-[4] on the top panel. The name of the function or parameter assigned
to each knob appears to the right of the corresponding button. If nothing is assigned to the button,
an indication of “---” is shown.
• The list shown in the USER DEFINED KNOB SETUP window is the same for all models of the CL
series.
For the CL3/CL1, the display will indicate “Cannot Assign!” you specify a parameter that does not
exist on that model.
• If there are no parameters for the registered USER DEFINED knob, nothing will occur when the
knob is operated.
About TOUCH AND TURN
The TOUCH AND TURN function is assigned to the USER DEFINED [4]
knob by default. If this function is assigned to one of the USER DEFINED
knobs, you can press a desired knob in the touch screen and then
immediately use the USER DEFINED knob to operate it.
At this time, a pink frame is shown around the knob in the touch screen,
indicating that you can operate that knob.
Functions that can be assigned to USER DEFINED
knobs
Function
PARAMETER 1 PARAMETER 2
NO ASSIGN - -
AUTOMIXER WEIGHT *1)
BRIGHTNESS
LAMP -
PANEL -
SCREEN -
CH COLOR -
NAME -
CUE
INPUT PFL TRIM -
DCA TRIM -
OUTPUT PFL TRIM -
CUE LEVEL -
DIRECT OUT LEVEL LEVEL *14)
DYNAMICS1
THRESHOLD *2)
RANGE *4)
RATIO
*2)
ATTACK
HOLD
*4)
DECAY
RELEASE
*2)OUTGAIN
KNEE
WIDTH *13)
DYNAMICS2
THRESHOLD
*4)
RATIO
FREQUENCY
ATTACK
RELEASE
OUTGAIN
KNEE
WIDTH
EFFECT
Displays the EFFECT RACK No. (1-8) for
the target operation as well as the
name of the mounted EFFECT TYPE or
the name of the GEQ/PEQ TYPE *a).
Displays the names of the 32 parame-
ters for the EFFECT TYPE *b). Displays
“----” if a GEQ/PEQ is mounted.