User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Setup
V5 Reference Manual
222
5 FILE LOAD
Specifies the types of file that can be loaded from USB flash drives. The user
authentication key contains the user level, USER DEFINED keys, and Preference settings.
Other data is saved in an “ALL” file. The “ALL” file also includes the USER SETUP settings
of the Administrator and the Guest.
• USER SETUP (USER DEFINED keys and Preferences settings)
• SYSTEM SETUP/MONITOR SETUP
• CURRENT SCENE
• SCENE LIST
• LIBRARY LIST
6 MONITOR SETUP
Specifies the monitor setup operations that can be performed.
•OSCILLATOR
• TALKBACK
•SOLO
7 SYSTEM SETUP
Specifies the system setup operations that can be performed.
• MIXER SETUP
• OUTPUT PORT
• MIDI/GPI
• DANTE SETUP
NOTE
• The content that is restricted with the DANTE SETUP button is as shown below.
• Changing the CONSOLE ID
• Changing the SECONDARY PORT setting
• Changing control of DANTE PATCH changes (THIS CONSOLE or DANTE CONTROLLER)
• Changing BIT DEPTH
• Changing LATENCY
• Changing DEVICE MOUNT
• Changing REMOTE HA ASSIGN
• Changing the Dante Input Patch
• Changing the Dante Output Patch
• Changing the Dante Input Patch Library (Changing Store, Recall, Clear, Library Name)
• If an operation is restricted, the message “This operation is not allowed.” is displayed at the
bottom of the screen.
• With the factory settings, this is turned off (no restrictions).
8 SET ALL/CLEAR ALL button
Permits/clears all items.
Preferences
Follow the steps below to make various settings for the CL console operating environment,
such as how windows appear, and whether [SEL] key on/off operations will be linked. These
settings are changed for the user who is logged-in, but if you are logged-in as the
Administrator, you will also be able to change the Guest settings.
NOTE
If you are logged-in as the Administrator, you can also turn on the FOR GUEST button to access
the PREFERENCE for Guest page and make preference settings for the Guest account.
USER SETUP window (PREFERENCE page)
1 STORE/RECALL field
Enables you to turn on or off options related to scene store/recall operations.
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the USER SETUP button.
3. In the USER SETUP window, press the PREFERENCE tab.
4. Use the buttons on screen to make Preference settings.
5. When you have finished making settings, close the window and press the SETUP
button in the Function Access Area.
1
2
3
4
5