User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/output characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
Reference Manual
148
6 Channel number
Displays the channel number and channel name of the channel to be inserted.
7 man/auto/mute
Toggles between man/auto/mute.
man: Passes the audio through without changing the gain. This mode is used for
singing with a mic.
auto: Turns on Automixer. This mode is used for conversations.
mute: Mutes channels.
8 preset
Selects the channel mode (man/auto/mute) when the PRESET button in the master field
is pressed. The preset button lights when a preset is programmed for a channel.
Master field
1
OVERRIDE/PRESET/MUTE
Makes settings for each group (a/b/c) selected in the channel control field. Shows only
the selected group.
• OVERRIDE
When you press this button, channels where the channel override button is on will
fade in to 0 dB (unity gain). All channels with the override button turned off will be
muted.
• PRESET
When you press this button, each channel will switch to the mode indicated by the
mode button (man/auto/mute) next to the lit preset indicator.
•MUTE
When you press this button, all channels will fade out immediately (0.5 seconds).
2 meters
Switches the meter indicator in the channel control field. Toggles between gain, input,
and output each time you press the button.
NOTE
Meters should normally be set in gain mode.
3 reset
Initializes the Automixer settings.
Editing the internal effects
The internal effects of the CL series console can be mounted in EFFECT racks 1-8, and
patched to an output channel’s output or input channel’s input, or inserted into a channel. For
each effect mounted in a rack, you can choose one of 54 types of effect.
With the default settings, the signals from MIX channels 17-24 are input to racks 1-8, and from
the racks are then output to ST IN 1-8 (L/R).
NOTE
Some effect types can be mounted only in racks 1, 3, 5 or 7.
To use an internal effect via send and return, assign the output of a MIX channel to the input
of the effect, and assign the output of the effect to an input channel. In this case, the
corresponding output channel is used as a master channel for the effect send, and the input
channel is used as an effect return channel.
Alternatively, you can assign the input and output of the internal effect to the insert-out/in of a
desired channel (except for a ST IN channel), so that the effect is inserted into that channel.
The internal effects fall into two categories; “STEREO type” (2-in/2-out) effects that process
the L/R channel input signals independently, and “MIX type” (1-in/2-out) effects that mix the
two channels before processing them.
If signals are assigned to both the L and R inputs of an effect, the way in which the L/R
channels are processed will depend on whether a Stereo effect type or a Mix effect type is
selected, as follows.
1
32
OUTPUT PATCH
INPUT PATCH
EFFECT
EFFECT
EFFECT
EFFECT
Rack 2
Rack 7
Rack 8
Output of the
output
channel
Input of the input
channel
Rack 1
EFFECT
Insert-out of a
desired channel*
Insert-in of a
desired channel*
* Excluding a ST IN channel