User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/output characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Setup
Reference Manual
246
NETWORK window
1 IP ADDRESS
Specifies an address that identifies an individual device on the Internet or LAN network.
2 GATEWAY ADDRESS
Specifies an address that identifies a device (gateway) that converts data between
different media or protocols to allow communication within the network.
3 SUBNET MASK
Within the IP address used in the network, this defines the bits that are used for the
network address that distinguishes the network.
4 MAC ADDRESS
Indicates the MAC (Machine Access Control) address, which identifies a host in a
network. This address is for display only, and cannot be edited.
5 UNIT NAME
Sets the name to be shown on the network.
6 PIN for MonitorMix
Sets the PIN (4-digit numeric password) to be entered when using the MonitorMix
application to connect to a CL series console. MonitorMix is an iOS application that
musicians can use on stage to adjust their own monitor balance.
You can register a PIN with all 4 digits blank. In that case, PIN authentication with
MonitorMix is not required. However, you cannot leave only 1, 2, or 3 of the PIN digits
blank.
NOTE
The NETWORK connector on the CL series console transmits data via either 100BASE-TX
(transmission speed: maximum 100 Mbps) or 10BASE-T (transmission speed: max 10 Mbps).
Dante audio network settings
You will use the CL series console to make Dante audio network settings for the console itself
and the I/O devices connected to the Dante connector of the CL series console. This section
explains how to make Dante audio network settings.
1
2
3
4
6
5
STEP
1. In the Function Access Area, press the SETUP button to access the SETUP screen.
2. In the DANTE field at the center of the screen, press the DANTE SETUP button to
open the DANTE SETUP window.
3. Press the SETUP tab in the lower part of the DANTE SETUP window.
SETUP screen DANTE SETUP window