User Manual
Table Of Contents
- このリファレンスマニュアルの使い方
- 目 次
- 機能ツリー図
- セレクテッドチャンネルセクション
- Centralogicセクション
- 入出力のパッチング
- インプット系チャンネル
- アウトプット系チャンネル
- EQ/ダイナミクス
- チャンネルジョブ
- シーンメモリー
- モニター/キュー
- トークバック/オシレーター
- メーター
- グラフィックEQ/パラメトリックEQ/エフェクト/ PREMIUM RACK
- I/Oデバイスと外部ヘッドアンプ
- MIDI
- レコーダー
- AFC IMAGEコントロール
- セットアップ
- SETUP画面について
- ユーザー設定
- プリファレンス設定
- USER DEFINEDキー
- USER DEFINEDキーに割り当て可能な機能
- USER DEFINEDノブ
- USER DEFINEDノブに割り当て可能な機能
- アサイナブルエンコーダー
- ASSIGNABLE ENCODERに割り当て可能な機能
- GAIN/PAN/ASSIGNノブ(アサイナブルエンコーダー)の機能
- カスタムフェーダーバンク
- メインフェーダー
- カスタムフェーダーバンクの機能について
- コンソールロック
- 設定データをUSBメモリーにセーブ/ロードする
- USBメモリーをフォーマットする
- ワードクロック/スロットの設定
- カスケード接続を利用する
- MIXバス/MATRIXバスの基本設定
- ファンタム電源全体のオン/ オフを切り替える
- タッチスクリーン/LED/ネーム表示/ランプの輝度を設定する
- 内蔵時計の日時を合わせる
- ネットワークアドレスを設定する
- Danteオーディオネットワークの設定
- Dante Device Lock
- Dante Domain Manager (DDM)対応
- GPI (汎用インターフェース)を使う
- ヘルプ機能
- そのほかの機能
- ワーニング/エラーメッセージ
- 索引
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Data List
17
DIST→DELAY
One input, two output distortion and delay effects in series.
MULTI FILTER
Two input, two output 3-band multi-filter (24 dB/octave).
FREEZE
One input, two output basic sampler.
DISTORTION
One input, two output distortion effect.
Parameter Range Description
DST TYPE
DST1, DST2, OVD1,
OVD2, CRUNCH
Distortion type (DST = distortion, OVD = overdrive)
DRIVE 0-100 Distortion drive
MASTER 0-100 Master volume
TONE -10 to +10 Tone control
N. GATE 0-20 Noise reduction
SYNC OFF/ON Tempo parameter sync on/off
DLY.NOTE
*1
*1. (Maximum value depends on the tempo
setting)
Used in conjunction with TEMPO to determine DELAY
MOD.NOTE
*2
*2.
Used in conjunction with TEMPO to determine FREQ
DELAY 0.0-2725.0 ms Delay time
FB. GAIN -99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
HI. RATIO 0.1-1.0 High-frequency feedback ratio
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
DLY.BAL 0-100%
Distortion and delay balance
(0% = all distortion, 100% = all delayed distortion)
Parameter Range Description
TYPE 1 LPF, HPF, BPF Filter 1 type: high pass, low pass, band pass
FREQ. 1 28.0 Hz-16.0 kHz Filter 1 frequency
LEVEL 1 0-100 Filter 1 level
RESO. 1 0-20 Filter 1 resonance
TYPE 2 LPF, HPF, BPF Filter 2 type: high pass, low pass, band pass
FREQ. 2 28.0 Hz-16.0 kHz Filter 2 frequency
LEVEL 2 0-100 Filter 2 level
RESO. 2 0-20 Filter 2 resonance
TYPE 3 LPF, HPF, BPF Filter 3 type: high pass, low pass, band pass
FREQ. 3 28.0 Hz-16.0 kHz Filter 3 frequency
LEVEL 3 0-100 Filter 3 level
RESO. 3 0-20 Filter 3 resonance
Parameter Range Description
REC MODE MANUAL, INPUT
In MANUAL mode, recording is started by pressing the REC and PLAY
buttons. In INPUT mode, Record-Ready mode is engaged by pressing the
REC button, and actual recording is triggered by the input signal.
REC DLY -1000 to +1000 ms
Recording delay.
For plus values, recording starts after the trigger is received. For minus
values, recording starts before the trigger is received.
PLY MODE
MOMENT, CONTI.,
INPUT
In MOMENT mode, the sample plays only while the PLAY button is
pressed. In CONT mode, playback continues once the PLAY button has
been pressed. The number of times the sample plays is set using the LOOP
NUM parameter. In INPUT mode, playback is triggered by the input signal.
TRG LVL -60 to 0 dB
Input trigger level (i.e., the signal level required to trigger recording or
playback)
TRG MASK 0-1000 ms
Once playback has been triggered, subsequent triggers are ignored for the
duration of the TRG MASK time.
START
*1
*1. 0.0-5941.0 ms (fs=44.1 kHz), 0.0 ms-5458.3 ms (fs=48 kHz)
Playback start point in milliseconds
END
*1
Playback end point in milliseconds
LOOP
*1
Loop start point in milliseconds
LOOP
NUM
0-100 Number of times the sample plays
PITCH -12 to +12 semitones Playback pitch shift
FINE -50 to +50 cents Playback pitch shift fine
MIDI TRG OFF, C1-C6, ALL The PLAY button can be triggered by using MIDI Note on/off messages.
START
[SAMPLE]
0-131000 Playback start point in samples
END
[SAMPLE]
0-131000 Playback end point in samples
LOOP
[SAMPLE]
0-131000 Loop start point in samples
Parameter Range Description
DST TYPE
DST1, DST2, OVD1,
OVD2, CRUNCH
Distortion type (DST = distortion, OVD = overdrive)
DRIVE 0-100 Distortion drive
MASTER 0-100 Master volume
TONE -10 to +10 Tone control
N. GATE 0-20 Noise reduction