User Manual
Table Of Contents
- Как пользоваться данным справочным руководством
- Содержание
- Иерархия функций
- Секция SELECTED CHANNEL
- Секция Centralogic
- Подключение на входе и выходе
- Входные каналы
- Прохождение сигналов для входных каналов
- Определение названия, значка и цвета канала
- Выполнение настроек HA (предусилитель)
- Передача сигнала из входного канала на шины STEREO/MONO
- Передача сигнала из входного канала на шину MIX/MATRIX
- Корректировка задержки между каналами (Input Delay (задержка на входе))
- Операции с библиотеками каналов
- Выходные каналы
- Эквалайзер и динамический процессор
- Группирование и связывание
- Банки памяти сцен
- О банках памяти сцен
- Использование банков памяти сцен
- Редактирование банков памяти сцен
- Применение функции Global Paste (глобальная вставка)
- Использование функции Focus (фокусировка)
- Использование функции Recall Safe (безопасное восстановление)
- Использование функции Fade (изменение громкости звука)
- Вывод сигнала управления на внешнее устройство вместе с загрузкой сцены (GPI OUT)
- Воспроизведение аудиофайла, связанного с загрузкой сцены
- Использование режима предварительного просмотра
- Функции Monitor (монитор) и Cue (контроль)
- Двусторонняя связь и осциллятор
- Индикаторы
- Графический эквалайзер, эффекты и Premium Rack
- Устройство ввода-вывода и внешний предусилитель
- MIDI
- Функциональные возможности MIDI на консоли серии CL
- Основные настройки MIDI
- Применение сообщений Program Change (изменение программы) для восстановления объектов сцен и библиотек
- Использование сообщений Control Change (изменение управления) для управления параметрами
- Использование сообщений Parameter Change для управления параметрами
- Пользовательские настройки (Безопасность)
- Настройки пользовательского уровня
- Предпочтения
- Клавиши USER DEFINED (определяемые пользователем)
- Определяемые пользователем регуляторы
- Доступные для переназначения преобразователи
- Пользовательский банк фейдеров
- Мастер-фейдер
- Блокировка консоли
- Сохранение и загрузка данных настройки с/на флэш- память USB
- Форматирование флэш-памяти USB
- Устройство записи
- Функция справки
- Прочие функции
- Об экране SETUP (настройка)
- Настройки синхронизации слов и гнезд
- Использование каскадных подключений
- Основные параметры для шин MIX и MATRIX
- Включение и выключение всего источника фантомного питания
- Настройка яркости сенсорного экрана, светодиодных индикаторов, экранов с названиями каналов и ламп
- Установка даты и времени встроенных часов
- Установка сетевого адреса
- Инициализация модуля с восстановлением заводских настроек по умолчанию
- Корректировка точки срабатывания сенсорного экрана (функция калибровки)
- Корректировка фейдеров (функция калибровки)
- Точная настройка усиления входного и выходного сигналов (функция калибровки)
- Регулировка цвета канала (функция калибровки)
- Регулировка яркости экрана с названием канала
- Регулировка контрастности отображаемого названия канала.
- Настройки аудиосети Dante
- Использование GPI (General Purpose Interface — интерфейс общего назначения)
- Приложения
- Список элементов библиотеки EQ
- Список элементов библиотеки DYNAMICS
- Параметры Dynamics (динамический процессор)
- Список типов эффектов
- Параметры эффектов
- Параметры процессора Premium Rack
- Синхронизация эффектов с темпом
- Параметры, которые можно назначить для смены контроллеров
- Назначение параметров NRPN (незарегистрированный номер параметра)
- Применимость параметров микширования
- Функции, которые можно назначить клавишам USER DEFINED
- Функции, которые можно назначить для регуляторов USER DEFINED
- Функции, которые можно назначить для доступных для переназначения преобразователей
- Формат MIDI-данных
- Сообщения об ошибках/предупреждения
- Электрические характеристики
- Основные параметры микшера
- Т аблица характеристик MIDI-интерфейса
- Предметный указатель
Приложения
Справочное руководство
264
Формат MIDI-данных
В данном разделе описан формат данных, которые консоль
серии CL может распознавать, передавать и принимать.
1 CHANNEL MESSAGE
1.1 NOTE OFF (8n)
Reception
These messages are echoed to MIDI OUT if [OTHER COMMAND ECHO] is ON.
They are received if [Rx CH] matches, and used to control effects.
1.2 NOTE ON (9n)
Reception
These messages are echoed to MIDI OUT if [OTHER COMMAND ECHO] is ON.
They are received if [Rx CH] matches, and used to control effects.
1.3 CONTROL CHANGE (Bn)
Two types of CONTROL CHANGE can be transmitted and received; [NRPN] (Non-
Registered Parameter Numbers) and freely-assigned [TABLE] (1CH x 110) messages.
Select either [TABLE] or [NRPN].
Reception
These messages are echoed to MIDI OUT if [CONTROL CHANGE ECHO] is ON.
If [TABLE] is selected, these messages are received when [CONTROL CHANGE Rx] is
ON and [Rx CH] matches, and will control parameters according to the settings of the
[CONTROL CHANGE EVENT LIST]. For the parameters that can be assigned, refer
to “Параметры, которые можно назначить для смены контроллеров” on стр. 248.
If [NRPN] is selected, these messages are received when [CONTROL CHANGE Rx] is
ON and the [Rx CH] matches; the four messages NRPN control number (62h, 63h) and
DATA ENTRY control number (06h, 26h) are used to control the specified parameter.
Transmission
If [TABLE] is selected, and if [CONTROL CHANGE Tx] is ON when you operate a
parameter that is assigned in the [CONTROL CHANGE EVENT LIST], these
messages will be transmitted on the [Tx CH] channel. For the parameters that can be
assigned, refer to “Параметры, которые можно назначить для смены
контроллеров” on стр. 248.
If [NRPN] is selected, and if [CONTROL CHANGE Tx] is ON when you operate a
specified parameter, the four messages NRPN control number (62h, 63h) and DATA
ENTRY control number (06h, 26h) are transmitted on the [Tx CH] channel. For the
parameters that can be assigned, refer to “Параметры, которые можно назначить
для смены контроллеров” on стр. 248.
CONTROL CHANGE messages are not used for transmission to CL Editor because
there is no guarantee that the contents of the assignment tables will match.
(PARAMETER CHANGE messages are always used.)
CONTROL CHANGE numbers 0 and 32 are for selecting banks.
If [TABLE] is selected
Equation for converting a Control Value to parameter data
paramSteps = paramMax – paramMin + 1;
add = paramWidth / paramSteps;
mod = paramWidth – add * paramSteps;
curValue = paramSteps * add + mod / 2;
(1) If the assigned parameter has fewer than 128 steps
paramWidth = 128; rxValue = Control value;
(2) If the assigned parameter has 128 or more but less than 16,384 steps
paramWidth = 16384;
(2-1) When High and Low data is received
rxValue = Control value(High) * 128 + Control value(Low);
(2-2) When only Low data is received
rxValue = (curValue & 16256) + Control value(Low);
(2-3) When only High data is received
rxValue = Control value(High) * 128 + (curValue & 127);
(3) If the assigned parameter has 16,384 or more but less than 2,097,152
steps
paramWidth = 2097152;
(3-1) When High, Middle, and Low data is received
rxValue = Control value(High) * 16384 + Control value(Middle) * 128 + Control value(Low);
(3-2) When only Low data is received
rxValue = (curValue & 2097024) + Control value(Low);
(3-3) When only Middle data is received
rxValue = (curValue & 2080895) + Control value(Middle) * 128;
(3-4) When only High data is received
rxValue = (curValue & 16383) + Control value(High) * 16384;
(3-5) When only Middle and Low data is received
rxValue = (curValue & 2080768) + Control value(Middle) * 128 + Control value(Low);
(3-6) When only High and Low data is received
rxValue = (curValue & 16256) + Control value(High) * 16384 + Control value(Low);
(3-7) When only High and Middle data is received
rxValue = (curValue & 127) + Control value(High) * 16384 + Control value(Middle) * 128;
if ( rxValue > paramWidth)
rxValue = paramWidth;
param = ( rxValue–mod / 2) / add;
If [NRPN] is selected
1.4 PROGRAM CHANGE (Cn)
Reception
If [PROGRAM CHANGE ECHO] is ON, bank select messages will also be echoed
from MIDI OUT.
If SINGLE CH is selected, these messages are received if [PROGRAM CHANGE Rx] is
ON and the [Rx CH] matches. However if [OMNI] is ON, these messages are received
regardless of the channel. When these messages are received, scene memory, effect
librarya nd premium rack library are recalled according to the settings of the
[PROGRAM CHANGE EVENT LIST].
Transmission
If [PROGRAM CHANGE Tx] is ON, these messages are transmitted according to the
[PROGRAM CHANGE Table] settings when scene memory, effect library and
premium rack library are recalled.
If SINGLE CH is selected, these messages are transmitted on the [Tx CH] channel.
If the recalled scene memory, effect library and premium rack library has been assigned
to more than one PROGRAM NUMBER, the lowest-numbered PROGRAM NUMBER
for each MIDI channel will be transmitted.
PROGRAM CHANGE messages are not used for transmission to CL Editor because
there is no guarantee that the contents of the assignment tables will match.
(PARAMETER CHANGE messages are always used.)
You can choose either MULTI MIDI CH or SINGLE CH.
If SINGLE is selected
You can choose the Rx CH, OMNI CH, and Tx CH.
You can choose whether a bank select message will be added.
A bank of up to 16 can be specified.
If MULTI is selected
The Rx and Tx channels will be the same.
The assignment table will use the settings for each MIDI channel. Bank select messages
will not be added.
You can make settings for up to sixteen MIDI channels.
STATUS 1000nnnn 8n
Note off message
DATA 0nnnnnnn nn
Note number
0vvvvvvv vv
Velocity (ignored)
STATUS 1001nnnn 9n
Note on message
DATA 0nnnnnnn nn
Note number
0vvvvvvv vv
Velocity (1-127:on, 0:off)
STATUS 1011nnnn Bn
Control change
DATA 00
Control number (00)
0vvvvvvv vv
Control Value (0-127)
STATUS 1011nnnn Bn
Control change
DATA 20
Control number (32)
0vvvvvvv vv
Control Value (0-127)
STATUS 1011nnnn Bn
Control change
DATA 0nnnnnnn nn
Control number (1-5, 7-31, 33-37, 38-95,
102-119) *
0vvvvvvv vv
Control Value (0-127)
* Numbers 0, 32, and 96–101 cannot be used.
* Control number 6, 38 can be used.
STATUS 1011nnnn Bn
Control change
DATA 01100010 62
NRPN LSB
0vvvvvvv vv
Parameter number LSB
STATUS 1011nnnn Bn
Control change *
DATA 01100011 63
NRPN MSB
0vvvvvvv vv
Parameter number MSB
STATUS 1011nnnn Bn
Control change *
DATA 00000110 06
Data entry MSB
0vvvvvvv vv
Parameter data MSB
STATUS 1011nnnn Bn
Control change *
DATA 00100110 26
Data entry LSB
0vvvvvvv vv
Parameter data LSB
* The STATUS byte of the second and subsequent messages need not
be added during transmission. Reception must occur correctly
whether or not the status byte is omitted.
STATUS 1100nnnn Cn
Program change
DATA 0nnnnnnn nn
Program number (0-127)