User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Monitor and Cue functions
V5 Reference Manual
121
3 OUTPUT CUE group
The cue signals of output channels make up this group. To switch Cue on or off for this
group, press the [CUE] key in the Master section, or assign MIX channels or MATRIX
channels to the Centralogic section and press a [CUE] key in the Centralogic section.
NOTE
If STEREO/MONO channels are assigned to the Centralogic section, you can also use the [CUE]
keys in the Centralogic section to enable Cue for this group.
4 Other CUE group
These cue signals are operated via buttons displayed on the
touch screen. This group is enabled if you turn on the CUE
button in the EFFECT window or the PREMIUM window, or
if you turn on the KEY IN CUE button in the DYNAMICS 1
window. This group will automatically be disabled when
you exit the corresponding window.
NOTE
You cannot turn on cue monitoring between different groups simultaneously. Normally, the group
to which the most recently-pressed [CUE] key (or on-screen CUE/KEY IN CUE button) belongs
will take priority, and the [CUE] keys for the previously-selected group will be defeated.
However, if you switch the Cue signal group in a specific order, the state of the [CUE] keys of the
previously-selected group will be restored when the current Cue signal is defeated.
The following illustration shows the
priority order of the [CUE] keys. After
you have switched groups from lower
to upper levels, if you then defeat cue
for the upper group, the previous
[CUE] key status of the group
immediately below will be restored.
For example, if you switch groups in
the order of OUTPUT CUE group
DCA CUE group INPUT CUE group
Other CUE group, you can then
successively defeat the [CUE] keys
(CUE/KEY IN CUE buttons) to
successively restore the [CUE] key
status of the previously-selected group.
[CUE] key in the Master section
[CUE] key in the Centralogic section
(When operating the MIX channel or
MATRIX channel)
On-screen CUE button
Other CUE group
INPUT CUE group
DCA CUE group
OUTPUT CUE group