V2.0 Supplementary Manual This supplementary manual explains mainly the functions that have been added or changed in CL5/CL3/CL1 firmware V2.0. Use it in conjunction with the CL5/CL3/CL1 Owner’s Manual, Reference Manual, and V1.7 Supplementary Manual.
Contents Contents SELECTED CHANNEL section ...................................................... 3 Added fader function............................................................................................... 3 Added insert function .............................................................................................. 3 Input channels .......................................................................... 4 Added gain function .............................................................
SELECTED CHANNEL section SELECTED CHANNEL section Added insert function You can now insert two devices into a single channel or bus. Added fader function ■ Setting inserts The TOUCH AND TURN function assigned to one of the USER DEFINED knobs enables you to control the fader in the FADER field of the SELECTED CHANNEL VIEW screen. 1. Use a bank select key or [SEL] key to select the channel or bus to which you want to insert devices. 2.
Input channels 4. Input channels Select an output port or input port. NOTE • There is a limit to the sum of INSERT 1 and INSERT 2 for each channel group, as shown in the table below. You can select any output or input ports.
Grouping and linking ■ Setting the DCA Roll-out function Grouping and linking 1. In the Function Access Area, press the CH JOB button. DCA Roll-out function DCA GROUP button You can now access all of the channels assigned to a DCA group simultaneously through the fader banks. This function enables flexible fader operations.
Grouping and linking Added DCA output channels You can now assign the Stereo/Mono bus master, Mix bus master, and Matrix bus master channels to a DCA group. DCA groups were formerly used exclusively for input channels. However, with this new feature, you can use the DCA groups for output master channels, which enables for more flexible simultaneous controls. 2 1 1. In the Function Access Area, press the CH JOB button. 2.
Grouping and linking 2. Added mute group function The MIX MINUS popup window will open. You can now unmute a muted channel in the mute group temporarily. If the master button is turned on for the mute group to which the target channel belongs, press the [ON] key for that channel to temporarily unmute the channel. However, in Preview mode, any operation during mute will be invalid. Added channel link function Recall Safe parameters are now linked for linked channels.
Scene memory Scene memory • R (READ ONLY) symbol Not only will the scene be protected, it will also not be overwritten by any file loaded from a USB flash drive. You can only apply the protect setting to scenes with consecutive scene numbers starting with scene #001. Added scene memory function • No symbol No scene will be protected. Now you can create a read-only scene memory. By specifying certain scenes as read-only, you can prevent those scenes from being overwritten when you load a console file.
Graphic EQ, Effects, and Premium Rack Graphic EQ, Effects, and Premium Rack Enhanced Graphic EQ functions Now you can compare the sound before and after gain adjustments during GEQ operations. In the GEQ popup window, use the buttons in the FADER ASSIGN field to specify the frequency band you want to control. Adjust the gain value using the fader assigned for the specified frequency band.
User settings User settings Recorder (Nuendo Live) Functions added to the channel name display Added Recorder (Nuendo Live) function You can now view the gain reduction meters for Dynamics 1 and 2, as well as other information, on the channel name display. In addition, if a channel is off during SENDS ON FADER mode, the channel name display will be highlighted. The current CL version supports Yamaha Console Extension V2. Due to this support, you can now edit the marker description from the console.
Other functions Other functions Function PARAMETER 1 SENDS ON FADER MIX1-24 PARAMETER 2 NORMAL/WITH CUE Added GPI functions MTRX1-8 NORMAL/WITH CUE New functions have been added that can be set for GPI OUT. MIX ON FADER NORMAL/WITH CUE Function DANTE PARAMETER 1 PARAMETER 2 REDUNDANCY IND.
Yamaha Pro Audio Global Web Site http://www.yamahaproaudio.com/ Yamaha Manual Library http://www.yamaha.co.jp/manual/ C.S.G.