Specifications
I
~~
I
The
Split
Mode
(CLP-880/860)
JJj
I
The split mode makes it possible to play two different voices on the keyboard
one with the left hand and another with the right hand. The Left Voice is
played
on
all keys to the left of (and including) a specified "split pgint"
key,
while
the Right Voice is played
on
all keys to the right of the split point
key.
~...
/
IZZ
0
ROCK
0
~/~~c
~
/!lm1n~
Example:
~
A-
I
b:
,
('
-,
IF
-,?
II
,
,_
c
A-1
B~-1
C2
F~2
o
"~"
is
indicated with a
lower"
n,
o
"fi"
is indicated with an upper
u-",
To activate the split mode simply press the
[SPLIT]
button so thats
indicator lights. The split mode
can
be
turned off at any time by pressing the
[SPLIT]
button again so that its indicator goes out.
[jj]l,l]
NOTE
1 • The dual
and
split modes cannot be engaged
at
the same time.
o Selecting the Right and Left Voices
..................................................
..
The
voice that was selected before the split mode was engaged becomes
the Right Voice in the split mode. (The Right Voice can also be changed while
in the split mode, by simply pressing the corresponding voice selector.)
To select a Left Voice press the corresponding voice selector while
holding the
[SPLIT]
button (default: [BASS]).
The
indicator
of
the Left
Voice selector will light while
the
[SPLIT]
button is pressed, then only the
Right Voice selector
and
[SPLIT]
button indicators will remain lit.
~
NOTE
1 • The variation can be individually tumed on
and
off
for the split mode voices.
Normally the voice indicator
of
the Right
Voice
lights in the split mode. The
[VARIATION] can
be
used
to
turn the variation for the Right Voice on
or
off as
required. While the [SPLIT] button is held, however, the voice indicator
of
the
Left Voice lights,
and
in this state the [VARIATION] button can be used to turn
the variation for the Left Voice on
or
off
as required .
• [EFFECT] in the
Split
Mode
Depending upon the conditions, one effect type will take priority over the other.
Depth will
be
decided according to the depth default value
of
the voice
combination. However, using function F4 (see page 30) you can change the
depth value for each voice
as
you like.
Effect depth setting via the panel controls (i.e. pressing the [-INO]
or
[+IYES]
buttons while holding the [EFFECT] button - see page
19) will be applied to
the Right Voice
only.
• [REVERB] In the
Split
Mode
The reverb type assigned to the Right Voice will take priority over the other. (It
the reverb is set to
OFF,
the Left Voices reverb type will be in affect.)
Reverb depth setting via the panel controls (i.e. pressing the [-INO]
or
[+lYES]
buttons while holding the [REVERB] button - see page
18) will be applied to
the Right Voice
only.
o Setting the Split Point
........................................................................................
.
The
split point is initially set at the F#2 key by default. You can change
the split point to any other key by pressing the key while holding the
[SPLIT]
button (the
name
of
the current split-point key appears
on
the
LED
display while
the
[SPLIT]
button is held).
The
split point
can
also be set via
the Function
mode
(see below).
o Other Split Mode Functions
.......................................................................
..
The
Clavinova Function
mode
provides access to a
number
of
other
split-mode functions, listed below.
See
the corresponding pages for details.
o Split Point ...................................................... 30
• Split Balance ................................................. 30
• Right Voice Octave Shift ...............................
31
• Left Voice Octave Shift ..................................
31
• Right Voice Effect Depth ...............................
31
• Left Voice Effect Depth ..................................
31