CRW4001t SERIES User Guide Guide de I’utilisateur Bedienungsanleitung
COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: FAX: Type of Equipment: Model Name: Yamaha Systems Technology, Inc. 100 Century Center Court San Jose, California 95112 (408) 467-2330 (408) 437-8791 CD Recorder CRW4001t CRW4001t-NB This device complies with Part 15 of the FCC Rules.
Laser Diode Properties Material : GaAlAs Wavelength : 780-790 nm Emission Duration : Continuous Laser Output Power : Less than 44.6 µW* * This output is value measured at a distance 200mm from the objective lens surface on the optical pick-up block. ANSI Class : Class 1 CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUKT CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
WARNING ❢ WARNING ❢ • The temperature where CRW4001t is located should be between 5ºC and 40ºC (41ºF – 104ºF), when used in a fan-cooled system. • Do not disassemble the CRW4001t cover to reduce the risk of electric shock. • Always remove the disc before transporting CRW4001t.
Important Precautions Important Precautions Please read the following precautions before attempting to operate the CRW4001t. • Before recording a disc, be sure to clean the disc and tray using an air aerosol-type dust remover. A dust particle on the disc may cause recording to fail, producing an unusable disc. • Always record in a dust-free environment. If the disc must be removed from the CRW4001t before recording is finished, store the disc in a clean, dust-free environment.
Table of Contents Table of Contents Introduction ............................................................................. 1 CRW4001t Features ...................................................... 1 Orange Book Compatible Recording ............................ 2 Chapter 1 - System Configuration ..................................... 3 Computer ....................................................................... 3 Software.........................................................................
Introduction Introduction Thank you for purchasing a Yamaha CRW4001t drive. Please read this manual before using the drive in order to make the best use of the superior CRW4001t functions. After reading, please retain this manual for future reference. CRW4001t Features ■ 2xS Recording (Rewritable) - 4xS Recording (Recordable) 6xS Reading The CRW4001t is able to write (overwrite) CD-RW discs at double speed, and is able to write CD-R discs at quad speed, double speed, or normal speed.
Introduction Orange Book Compatible Recording Track at Once In this mode, data can be recorded to disc one track at a time. Discs recorded in this mode cannot be played in CD players or CD-ROM drives other than a CD-RW or CD-R drive until the session is closed. Multisession In this mode, data can be recorded to disc in stages (one session at a time). Additional data can be written later. Disc at Once In this mode, data can be recorded to an entire disc in one pass.
Chapter 1 - System Configuration Chapter 1 - System Configuration Before using the CRW4001t, make sure that you have all of the items on the list of included items. In order to use the CRW4001t, you will require the following.
Chapter 1 - System Configuration Discs On the CRW4001t, you can use conventional CD-RW and CD-R discs that conform to the Recordable Compact Disc Systems Part 2 and Part 3 (Orange Book).
Chapter 2 - Installing the Yamaha CRW4001t Drive Chapter 2 - Installing the Yamaha CRW4001t Drive MASTER/SLAVE settings Before you install the CRW4001t in your computer, you must make the MASTER/SLAVE setting. This setting is set by inserting a jumper pin in the jumper switch located on the rear panel of the CRW4001t drive. Important: When the unit is shipped from the factory, this setting is in the MASTER position. Note: Use long-nose pliers to remove or insert the jumper pin.
Chapter 2 - Installing the Yamaha CRW4001t Drive ♦ Setting the CRW4001t as the MASTER As shown in the diagram at the right, insert the jumper pin into the right edge of the jumper switch. T CSEL SLAVE MASTER IDE INT Note: If only the CRW4001t will be connected to the IDE interface connector, connect the CRW4001t to the end of the connector. ♦ Setting the CRW4001t as the SLAVE As shown in the diagram at the right, insert the jumper pin into the middle of the jumper switch.
Chapter 2 - Installing the Yamaha CRW4001t Drive Installing the CRW4001t drive The following steps will differ slightly depending on the type of computer you are using. For details on removing the cover from your computer, and installing or removing internal devices, refer to the manual for your computer. 1. Switch off your computer, and unplug it from the AC outlet.
Chapter 2 - Installing the Yamaha CRW4001t Drive 4. Remove the front cover of a vacant half-height drive bay. For details refer to the manual of your computer. 5. Slide the CRW4001t drive into the drive bay from the front. At this time, be careful not to apply excessive force to the drive itself. Finger-tighten the four fastening screws, and check that there is enough room to connect the power supply cable, IDE interface connector, and AUDIO cables. 6. Connect the IDE interface connector.
Chapter 2 - Installing the Yamaha CRW4001t Drive PUT DC IN . R. NO SE UT IO O L R G AUD L CSE E SLAV R TE MAS R IDE +5V +12V G ECTO ONN EC RFAC 1 INTE 7. Connect the AUDIO cable. Connect the single 4-pin connector (Sound Blaster compatible) to the sound card. Connect the 4-pin connector at the other end of the cable (the larger connector) to the AUDIO OUT connector on the CRW4001t drive. The polarizing lug should be at the top. PUT DC IN . .
Chapter 2 - Installing the Yamaha CRW4001t Drive 8. Connect the power supply cable. Connect the +12V and +5V 4-pin power cable to the power supply interface located on the rear panel of the CRW4001t drive. The shape of the connector makes it impossible to reverse the connections. PUT DC IN . .
Chapter 2 - Installing the Yamaha CRW4001t Drive 10. Attach the cover of your computer. 11. Connect the power cable to an AC outlet, and switch on your computer. Make sure that the LED located on the panel of the CRW4001t drive is lit. ON PUSH 12. Start up your operating system. For the procedure, refer to the manual for your operation system. 13. Install the writing software. For the installation procedure, refer to the manual for your writing software.
Chapter 3 - Operation Chapter 3 - Operation Front Panel 6 1 2 3 4 5 1 Disc tray The disc is inserted and ejected here. Pressing the eject button will open the tray. 2 Headphone jack This stereo mini jack allows you to connect headphones and listen to audio. 3 Headphone volume control This control adjusts the volume level of the headphone output. Rotating the control clockwise will increase the volume level.
Chapter 3 - Operation Loading a Disc 1. Press the eject button to open the tray. 2. Carefully place the disc, label-side up, on the disc tray. 3. Press the disc tray softly or press the eject button again to close the disc tray.
Chapter 3 - Operation Ejecting the Disc If the CRW4001t is powered on: Press the eject button to eject the disc. Note: You cannot eject the disc if the ATAPI command prohibits the eject operation while the CRW4001t is reading data. Caution: Be sure to remove the disc after it is completely ejected. (Trying to remove the disc before it is completely ejected may cause the drive to malfunction.
Troubleshooting Troubleshooting If CRW4001t is not performing as expected, look up the symptoms in the following table, and take the appropriate corrective action. Symptoms Corrective action The power to the CRW4001t is off • Check the DC power cable connection. The CRW4001t is not recognized by • Check the IDE interface connector connection.
Appendix Specifications Interface ATAPI/IDE Data Capacity 1.2m/sec: 666MB 1.4m/sec: 540MB Record/Read Speed Writing (CD-RW): 2X speed Writing (CD-R): Normal speed, 2X speed, 4Xspeed Reading: Normal speed, 2X speed, 4X speed, 6X speed Data Transfer Rate 6xS: 900KB/sec 4xS: 600KB/sec 2xS: 300KB/sec 1xS: 150KB/sec Burst Transfer Rate 5.
Appendix Front Panel Indicator Key ● on: green ✦ flashing: green ❍ on: orange ✧ flashing: orange Status — off ON/DISC Read/Write ❍➠— ❍➠— ❍ — Inserting disc ✧➠✦ — Ejecting disc ✧ — Ready (disc inserted) ● — Seeking ● ✦ Preparing to write ● ✧ Writing ● ❍ Writing (test mode) ● ✧ Playback ● ● Reset Ready (no disc) 17
English: If you have any questions, please contact your dealer or one of the following companies. French: Pour plus de détails sur les produits, veuillez vous adresser à Yamaha ou au distributeur le plus proche figurant dans la liste suivante : German: Bei weiteren Fragen wenden Sie sich Sitte an Ihren Händler oder eine der folgenden Firmen.
