CRW4260t SERIES User Guide Guide de I’utilisateur Bedienungsanleitung
COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: FAX: Type of Equipment: Model Name: Yamaha Systems Technology, Inc. 100 Century Center Court San Jose, California 95112 (408) 467-2330 (408) 437-8791 CD Recorder CRW4260t-B CRW4260t-NB This device complies with Part 15 of the FCC Rules.
Laser Diode Properties Material : GaAlAs Wavelength : 782-789 nm Emission Duration : Continuous Laser Output Power : Less than 44.6 µW* * This output is value measured at a distance 200mm from the objective lens surface on the optical pick-up block. ANSI Class : Class 1 CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUKT CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
WARNING ❢ WARNING ❢ • The temperature where CRW4260t is located should be between 5ºC and 40ºC (41ºF – 104ºF), when used in a fan-cooled system. • Do not disassemble the CRW4260t cover to reduce the risk of electric shock. • Always remove the disc before transporting CRW4260t.
Important Precautions Important Precautions Please read the following precautions before attempting to operate the CRW4260t. • Before recording a disc, be sure to clean the disc and tray using an air aerosol-type dust remover. A dust particle on the disc may cause recording to fail, producing an unusable disc. • Always record in a dust-free environment. If the disc must be removed from the CRW4260t before recording is finished, store the disc in a clean, dust-free environment.
Table of Contents Table of Contents Introduction ............................................................................. 1 CRW4260t Features ...................................................... 1 Orange Book Compatible Recording ............................ 2 Chapter 1 - System Configuration ..................................... 3 Computer ....................................................................... 3 Software.........................................................................
Introduction Introduction Thank you for purchasing a Yamaha CRW4260t drive. Please read this manual before using the drive in order to make the best use of the superior CRW4260t functions. After reading, please retain this manual for future reference. CRW4260t Features ■ 2xS Recording (Rewritable) - 4xS Recording (Recordable) 6xS Reading The CRW4260t is able to write (overwrite) CD-RW discs at double speed, and is able to write CD-R discs at quad speed, double speed, or normal speed.
Introduction Orange Book Compatible Recording Track at Once In this mode, data can be recorded to disc one track at a time. Discs recorded in this mode cannot be played in CD players or CD-ROM drives other than a CD-RW or CD-R drive until the session is closed. Multisession In this mode, data can be recorded to disc in stages (one session at a time). Additional data can be written later. Disc at Once In this mode, data can be recorded to an entire disc in one pass.
Chapter 1 - System Configuration Chapter 1 - System Configuration Before using the CRW4260t, make sure that you have all of the items on the list of included items. In order to use the CRW4260t, you will require the following.
Chapter 1 - System Configuration Tools • Phillips screwdriver This is used to remove the cover of your computer, and to install the Yamaha CRW4260t drive. • Phillips screwdriver Long nose pliers These are used to insert or remove the jumper pin when setting the SCSI ID and parity settings etc.of the Yamaha CRW4260t drive. Long nose pliers Discs On the CRW4260t, you can use conventional CD-RW and CD-R discs that conform to the Recordable Compact Disc Systems Part 2 and Part 3 (Orange Book).
Chapter 2 - Installing the Yamaha CRW4260t Drive Chapter 2 - Installing the Yamaha CRW4260t Drive CRW4260t drive settings Before installing the CRW4260t in your computer, you will need to set the following jumpers. You set these jumpers by inserting jumper connectors into the jumper switch located on the rear panel of the CD-RW drive. ♦ ♦ ♦ ♦ SCSI ID settings Parity setting Terminator setting Block size setting Important: Use long-nose pliers to remove or insert jumper connectors.
Chapter 2 - Installing the Yamaha CRW4260t Drive Note: When you are using Windows 95, and if the SCSI ID setting on the rear panel is the same as the number assigned to another SCSI device, the Plug and Play component of Windows 95 will automatically assign an unused number to the CRW4260t (SCAM protocol level 1).
Chapter 2 - Installing the Yamaha CRW4260t Drive ♦ Terminator setting The terminator setting indicates whether or not this device is the last connected SCSI device. Terminator ON (with a jumper) — Use this setting if the CRW4260t is the last device in the internal SCSI daisy-chain. Terminator OFF (without a jumper) — Use this setting if devices other than the CRW4260t are in the internal SCSI daisy-chain and the CRW4260t is not the last device.
Chapter 2 - Installing the Yamaha CRW4260t Drive Installing the CRW4260t drive The following steps will differ slightly depending on the type of computer you are using. For details on removing the cover from your computer, and installing or removing internal devices, refer to the manual for your computer. 1. Switch off your computer, and unplug it from the AC outlet.
Chapter 2 - Installing the Yamaha CRW4260t Drive 4. Remove the front cover of a vacant half-height drive bay. For details refer to the manual of your computer. 5. Remove the SCSI card, and set the terminator setting of the SCSI internal circuit to the position for internal connected devices. For details refer to the manual of your SCSI card. 6. Slide the CRW4260t drive into the drive bay from the front. At this time, be careful not to apply excessive force to the drive itself.
Chapter 2 - Installing the Yamaha CRW4260t Drive VZ49 880-0 PUT SCSI ACE DC IN RF INTE ECTOR +12V CONN G VZ49 AUD IO O UT L RG 1 CT ELE ID S Y IT PAR INATOR M TER K SIZE C BLO 880-0 +5V 124 8. Connect the AUDIO cable. Connect the single 4-pin connector (Sound Blaster compatible) to the sound card. Connect the 4-pin connector at the other end of the cable (the larger connector) to the AUDIO OUT connector on the CRW4260t drive. The polarizing lug should be at the top.
Chapter 2 - Installing the Yamaha CRW4260t Drive 9. Connect the power supply cable. Connect the +12V and +5V 4-pin power cable to the power supply interface located on the rear panel of the CRW4260t drive. The shape of the connector makes it impossible to reverse the connections. VZ49 880-0 PUT SCSI ACE DC IN RF INTE ECTOR CONN G 88 VZ49 AUD CT ELE ID S Y IT PAR INATOR M TER K SIZE C BLO 0-0 IO O UT L RG 1 +12V +5V 124 10. Tighten the four fastening screws securely. 11.
Chapter 2 - Installing the Yamaha CRW4260t Drive 12. Connect the power cable to an AC outlet, and switch on your computer. Make sure that the LED located on the panel of the CRW4260t drive is lit. ON PUSH 13. Start up your operating system. For the procedure, refer to the manual for your operation system. 14. Install the writing software. For the installation procedure, refer to the manual for your writing software.
Chapter 3 - Operation Chapter 3 - Operation Front Panel 1 2 3 7 4 6 5 1 Disc tray The disc is inserted and ejected here. Pressing the eject button will open the tray. 2 Headphone jack This stereo mini jack allows you to connect headphones and listen to audio. 3 Headphone volume control This control adjusts the volume level of the headphone output. Rotating the control clockwise will increase the volume level.
Chapter 3 - Operation Loading a Disc 1. Press the eject button to open the tray. 2. Carefully place the disc, label-side up, on the disc tray. 3. Press the disc tray softly or press the eject button again to close the disc tray.
Chapter 3 - Operation Ejecting the Disc If the CRW4260t is powered on: Press the eject button to eject the disc. Note: You cannot eject the disc if the SCSI command prohibits the eject operation while the CRW4260t is reading data. Caution: Be sure to remove the disc after it is completely ejected. (Trying to remove the disc before it is completely ejected may cause the drive to malfunction.) Press the eject button If the CRW4260t is not powered on: Pressing the eject button will not eject the disc.
Chapter 3 - Operation Manual Eject (emergency use) Here we explain how to eject the disc when it cannot be ejected in the normal way; for example, the power is shut off inadvertently or the loading mechanism fails. This technique should be used only as a last resort. Frequent use may lead to malfunction. You’ll need a pin-like object of 2 mm or less in diameter to do this. A straightened paper clip makes an ideal tool. 1. Insert the pin-like tool into the manual eject hole and push gently.
Troubleshooting Troubleshooting If CRW4260t is not performing as expected, look up the symptoms in the following table, and take the appropriate corrective action. Symptoms Corrective action The power to the CRW4260t is off • Check the DC power cable connection. The power to the computer is off • Check to see if the SCSI card is correctly installed. The CRW4260t is not recognized by • Check the SCSI cable connection. the computer • Make sure that SCSI ID numbers are assigned exclusively.
Appendix Specifications Interface SCSI 2 Data Capacity 650MB (74 minutes) 550MB (63 minutes) Record/Read Speed Writing (CD-RW): 2X speed Writing (CD-R): Normal speed, 2X speed, 4Xspeed Reading: Normal speed, 2X speed, 4X speed, 6X speed Data Transfer Rate Burst Transfer Rate 6xS: 900KB/sec 4xS: 600KB/sec 2xS: 300KB/sec 1xS: 150KB/sec 4.2MB/sec (record asynchronous) 3.
Appendix Front Panel Indicator Key ● on: green ✦ flashing: green ❍ on: orange ✧ flashing: orange — off ON/DISC Read/Write ❍➠— ❍➠— ❍ — Inserting disc ✦➠✧ — Ejecting disc ✧ — Ready (disc inserted) ● — Seeking ● ✦ Preparing to write ● ✧ Writing ● ❍ Writing (test mode) ● ✧ Playback ● ● Status Reset Ready (no disc) 19
English: If you have any questions, please contact your dealer or one of the following companies. French: Pour plus de détails sur les produits, veuillez vous adresser à Yamaha ou au distributeur le plus proche figurant dans la liste suivante : German: Bei weiteren Fragen wenden Sie sich Sitte an Ihren Händler oder eine der folgenden Firmen.
