User's Manual
Table Of Contents
- Online Resources
- Contents
- Introduction
- About this Manual
- Getting Started
- User Interface
- Dialer Application
- Basic Operations
- Configuring the CS-700
- Configuring using the Web User Interface
- Configuring using the Service Application
- Configuring using a Provisioning Server, Option 66
- Configuring using a Provisioning Server, Option 150
- Provisioning file
- Provisioning file parameters (All Models)
- Using the Application Programming Interface (API)
- USB API functions
- Telnet / SSH interface
- USB/Telnet/SSH CLI Commands
- usb-conn-status
- speaker-volume
- ringer-volume
- speaker-mute
- mute
- camera-ptz-home
- camera-image-defaults
- camera-backlight
- camera-mute
- camera-pan
- cam-pan-left
- cam-pan-right
- camera-tilt
- cam-tilt-up
- cam-tilt-down
- camera-zoom
- cam-zoom-in
- cam-zoom-out
- cam-apply-defaults
- cam-image-apply-defaults
- status
- status-all
- call-info
- start-time
- dial
- answer
- hangup
- hold
- resume
- swap
- join
- transfer
- vm-count
- do-not-disturb
- dtmf
- registration
- Upgrading the Device Firmware
- Appendix
- Limited Warranty and Limitation of Liability
95
Property
Type
Values
Default Value
Description
bt.bt-enable
BOOLEAN
0 : disable
1 : enable
1
Enable or disable Bluetooth basic-rate.
bt.bt-name
TEXT
Name of device.
Default value is the product
name concatenated with the
system's BT MAC address
"Yamaha CS-
700 " + BT MAC
address
The Bluetooth basic-rate device name advertised over the air.
bt.bt-pin
TEXT
pin : 4-digit string
0000
The Bluetooth basic-rate pin for pairing. Pins are 4 digits or an
empty string to disable PINs.
bt.bt-pair-timeout
NUMBER
0 : No timeout
30, 60, 90, 120 : Pairing timeout
in seconds
The value can only be set in
increments of 30
60
Bluetooth basic-rate pairing timeout in seconds. After this time,
the pairing mode will stop. A value of 0 indicates no timeout.
bt.enable-nfc
BOOLEAN
0 : Disable NFC and NFC LED
1 : Enable NFC and NFC LED
1
Enable/disable NFC and the NFC logo LED on the main unit.
bt.bt-call-autojoin
BOOLEAN
0 : Disable
1 : Enable
0
Enable/disable Bluetooth call auto-join
bt.bt-auto-unpair
BOOLEAN
0 : Disable
1 : Enable
0
Enable/disable Bluetooth device auto-unpair
net.dhcp
BOOLEAN
0 : Disable DHCP
1 : Enable DHCP
1
Enables or disables DHCP. If DHCP is disabled, the Static IP
Address, Subnet Mask, and Default Gateway must be specified.
net.ip
TEXT
IP address
IP Address assigned to the device.
net.subnet
TEXT
IP address
Subnet Mask to determine the subnet to which the device belongs.
net.gateway
TEXT
IP address.
The Default Gateway is the device's default router on the IP
network.
net.dns1
TEXT
IP address.
Address of the primary Domain Name System (DNS) server.
net.dns2
TEXT
IP address.
Address of the secondary Domain Name System (DNS) server.
net.vlan
INDEXED_
OPTION
0 : Manually specify VLAN ID
1 : Disable VLAN
2 : Automatically detect VLAN ID
2
Specifies VLAN behavior and support for the device. 'Automatic'
(2) should be used in environments that provide a Voice VLAN with
automatic detection, in which case the device will determine the
VLAN identifier and register in that network. If the environment
uses Voice VLAN but the Voice VLAN ID cannot be detected,
choose ‘Enabled’ (0) and specify the ID in the VLAN ID field,
net.vlan-id. 'Disabled' (1) switches off VLAN capabilities.