!"#$ %&'() *+, EN
Information for users on collection and disposal of old equipment: This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation.
The model number, serial number, power requirements, etc., may be found on or near the name plate, which is at the bottom of the unit. You should note this serial number in the space provided below and retain this manual as a permanent record of your purchase to aid identification in the event of theft. Model No. The name plate is located on the bottom of the unit. Serial No.
PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING Please keep this manual in a safe and handy place for future reference. For the AC adaptor WARNING CAUTION • This AC adaptor is designed for use with only Yamaha electronic instruments. Do not use for any other purpose. • When setting up, make sure that the AC outlet is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch of the instrument and disconnect the AC adaptor from the outlet.
If you notice any abnormality • When one of the following problems occur, immediately turn off the power switch and disconnect the electric plug from the outlet. Then have the device inspected by Yamaha service personnel. - The power cord or plug becomes frayed or damaged. - It emits unusual smells or smoke. - Some object has been dropped into the instrument. - There is a sudden loss of sound during use of the instrument. - If any cracks or breakages exist on the instrument.
NOTICE Information To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below. About copyrights Handling • Do not connect this product to public Wi-Fi and/or Internet directly. Only connect this product to the Internet through a router with strong password-protections. Consult your router manufacturer for information on security best practices.
About the Manuals This instrument has the following documents and instructional materials. Included Documents Owner’s Manual (this book) Explains the basic operations and functions of this instrument. Please read this manual first. Online Materials (Downloadable from the web) Reference Manual (only in English, German, French and Spanish) Explains advanced features of the instrument, not explained in the Owner’s Manual.
Contents PRECAUTIONS ................................................................................................................................................... 4 NOTICE................................................................................................................................................................. 6 Information ...........................................................................................................................................................
Playing in Unison or Adding Accents to Style Playback (Unison & Accent)............................................ 54 Changing the Chord Fingering Type...............................................................................................................56 Changing the Split Points..................................................................................................................................58 4 Songs – Playing, Practicing and Recording Songs – 60 Playback of Songs ............
Welcome to the new DGX! The DGX-670 is equipped with a color display and has many advanced features that enhance your musical enjoyment and expand your creative and performance possibilities. Let’s take a look… Authentic piano sound This instrument features gorgeous piano Voices, created with samples of the Yamaha CFX flagship concert grand piano.
Lesson features with Score display Welcome to the new DGX! The Lesson features are a fun way to learn and master Songs, with notation shown on the display. For example, when you practice the right-hand part, the playback of the left part and other parts will wait for you to play the notes correctly. This allows you to practice melodies and phrases smoothly—even if you are a beginner.
Panel Controls and Terminals Top Panel 1 3 4 $ 5 6 2 7 8 9 ) @ ! # F PITCH BEND A-1 B-1 C0 D0 E0 F0 G0 A0 B0 C1 D1 E1 1 [P] (Standby/On) switch .................. page 16 Turns on the instrument’s power or sets to standby. 2 [MASTER VOLUME] dial ................. page 17 Adjusts the overall volume. 3 [DEMO] button.................................. page 11 Plays the Demos. 4 SONG related buttons........................ page 60 For selecting Songs and controlling Song playback.
^ & * Panel Controls and Terminals E ( B A % D C F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5 G5 A5 B5 C6 D6 E6 ^ [PLAYLIST] button............................ page 80 Calls up the Playlist display in which you can manage your repertoire. & [MIC SETTING] button .................... page 77 Calls up the display from which you can make settings for the microphone. F6 G6 A6 B6 C7 E [USB TO DEVICE] terminal ............. page 91 For connecting a USB flash drive or USB wireless LAN adaptor.
Rear Panel 1 2 3 1 [USB TO HOST] terminal ................. page 92 For connecting to a computer or smart device such as smartphone or tablet. 2 [AUX PEDAL] jack ......................... see below For connecting the included footswitch or separately sold foot pedals. 4 4 [MIC INPUT] jack ............................. page 77 For connecting a microphone. 5 [AUX IN] jack .................................... page 95 6 7 6 [PHONES/OUTPUT] jack.................
A separately sold LP-1B/LP-1WH pedal unit can be connected to the [PEDAL UNIT] jack. When connecting the pedal unit, make sure to also assemble the unit on the separately sold L-300B/L-300WH keyboard stand. The L-300B/L-300WH keyboard stand is designed to be used for multiple models. When assembling the keyboard stand for the DGX-670, make sure to use the screw holes indicated by “B” on the metal brackets of the stand. For details, refer to the assembly manual of the stand.
Starting Up Power Supply Connect the plugs of the AC adaptor in the order shown in the illustration. DC IN jack (page 14) 2 AC outlet DC plug 3 1 Power cord AC adaptor AC plug The shape of the plug and outlet differ depending on the locale. WARNING Use the specified AC adaptor (page 107) only. Using the wrong AC adaptor can result in damage to the instrument or overheating. CAUTION When setting up the product, make sure that the AC outlet you are using is easily accessible.
CAUTION Even when the [P] (Standby/On) switch is in standby status, electricity is still flowing to the instrument at the minimum level. Remove the electric plug from the outlet when the instrument is not to be used for extended periods of time, or during electrical storms. NOTICE While recording or editing, or while a message is displayed, the power cannot be turned off even if you press the [P] (Standby/On) switch.
Making Basic Settings As necessary, make basic settings for the instrument, such as the language shown on the display. 1 Call up the operation display. 1-1 Press the [MENU] button to call up the Menu display. 1-2 Use the Cursor buttons [U][D][L][R] to select System, and then press the [ENTER] button. 1-3 Press the TAB [L] button to select the Common tab. 1-3 1-1 1-2 2 2 Use the [1UD] – [8UD] buttons to make the necessary settings.
Basic Operations Display-based Controls The LCD provides comprehensive at-a-glance information on all current settings. The displayed menu or parameters can be selected or changed by the controls around the LCD. TAB [L][R] buttons (page 21) Cursor buttons [U][D][L][R] and [ENTER] button (see below) [1UD] – [8UD] buttons (page 20) Basic Operations Data dial (page 20) [EXIT] button (page 21) Cursor buttons [U][D][L][R] and [ENTER] button These buttons are used to move the on-screen cursor.
[1UD] – [8UD] buttons The [1UD] – [8UD] buttons are used to make selections or adjust settings (up or down correspondingly) for functions shown directly above them. In this manual, the upper buttons are described as [U] and the lower buttons as [D]. For menus that appear in this section of the display, use the [1U] – [8U] (upper) buttons. For menus that appear in this section of the display, use the [1D] – [8D] (lower) buttons.
Selecting files (Voice, Style, Song, and so on) The operation by using the Data dial is almost same as that of the Cursor buttons. After calling up the File Selection displays, rotate the Data dial to move the cursor, and then press the [ENTER] button to actually select and call up the file. In most procedures when selecting the file or item described throughout this Owner’s Manual, the Cursor buttons [U][D][L][R] are used for simple selection, though other methods may also be used.
Messages Shown in the Display A message (information or confirmation dialog) sometimes appears on the screen to facilitate operation. When the message appears, press one of the [1UD] – [8UD] buttons corresponding to the message. Calling Up the Desired Display Instantly — Direct Access With the convenient Direct Access function, you can instantly call up the desired display — with just a single additional button press.
Main Display Configuration The display that appears when the power is turned on is the Main display. This display shows the current basic settings such as the currently selected Voice and Style, allowing you to see them at a single glance. The Main display is the one you’ll usually see when you play the keyboard. The File Selection display (page 24) of Style, Song, Voice or Registration Memory Bank can also be called up from this display.
7 Bar/Beat Displays the current position (bar/beat) in Style playback or Song playback. 8 Microphone indicator Indicates the input level of the connected microphone (page 77). 9 Transpose Displays the amount of transposition in semitone units (page 44). File Selection Display Configuration The File Selection display is for selecting Voice, Styles, and other data (files). The File Selection display appears when you press one of the VOICE or STYLE category selection buttons, SONG [SELECT] button, etc.
Calling up a higher level folder When there are files in a folder, an up arrow is shown at the lower right of the display, allowing you to call up the higher level folder by pressing the [8U] button. Example of the Preset Voice Selection display The preset Voices are categorized and contained in appropriate folders. Basic Operations The next highest level (in this case, folder) is shown. Each folder shown in this display contains appropriately categorized Voices.
File Management You can save, name, copy, move, delete files, and you can create folders to manage the files with the buttons located lower area in the File Selection display. For information on the File Selection display, refer to page 24. NOTE Before using a USB flash drive, be sure to read “Connecting USB Devices” on page 91. Saving a File You can save your original data (such as Songs you’ve recorded) as a file to the instrument or USB flash drive.
5 Press the [8U] (OK) button to actually save the file. If the file name already exists, a message appears asking you if you want to overwrite or not. If not, press one of the [6UD] (No) buttons and enter another name. The saved file will be automatically located at the appropriate position among the files in alphabetical order. Creating a New Folder You can create folders to make it easier to find your original data.
Renaming a File/Folder You can rename files/folders. NOTE • Files and folders in the Preset tab cannot be renamed. • The PianoRoom folder (page 37) cannot be renamed. 1 In the File Selection display, select the appropriate tab (User or USB1) to which you want to rename by using the TAB [L][R] buttons. 2 Make sure that the File Management menu is shown at the bottom of the display. If the menu is not shown, press the [8D] (File) button to call it up. 3 Press the [1D] (Name) button.
Copying or Moving Files You can copy or cut files and paste them to another location (folder). You can also copy folders (but not move them) by using the same procedure. NOTE • Files in the Preset tab and the PianoRoom folder (page 37) cannot be moved. • Protected Songs such as preset Songs copied to the User tab are indicated by “Prot.1” above the Song name on the Song Selection display. These cannot be copied or moved to USB flash drives.
Deleting Files/Folders You can delete individual or multiple files/folders. NOTE • Files in the Preset tab cannot be deleted. • The PianoRoom folder (page 37) cannot be deleted. 1 In the File Selection display, select the appropriate tab (User or USB1) which contains the file/folder you want to delete by using the TAB [L][R] buttons. 2 Make sure that the File Management menu is shown at the bottom of the display. If the menu is not shown, press the [8D] (File) button to call it up.
Entering Characters This section covers how to enter characters for naming your files/folders, etc. Entering characters is done in the display shown below. 3 1 4 Basic Operations 2 NOTE • The following marks cannot be entered for a file/folder name: \ / : * ? " < > | • File names or folder names can contain up to 50 characters. 1 Change the type of character by pressing the [1U] button.
Other character-entry operations Deleting characters Move the cursor to the character you wish to delete by using the Data dial, and press the [7D] (Delete) button. To delete all characters on the line at once, press and hold the [7D] (Delete) button. Entering marks or space 1 2 Press the [6D] (Symbol) button to call up the mark list. Use the Data dial to move the cursor to the desired mark or space, and then press the [8U] (OK) button.
Data Backup You can back up all data saved in the User drive (except protected Songs) and all settings of the instrument to a USB flash drive as a single file (extension: bup.). The backup file can be restored to the instrument again, allowing you to recall the panel settings and performance data you created previously. For information on the settings that can be backed up, refer to the Backup/Restore column of the Parameter Chart in the Data List on the website.
Resetting to the Factory-programmed Settings (Initializing) While holding the right-most key (C7) on the keyboard, turn the power on. This resets (or initializes) all of the settings (referred to as the System Setup parameters) to their factory default, with the exceptions of Language (page 18), Owner Name (page 18) and Bluetooth pairing information (page 96). Refer to the Parameter Chart in the Data List on the website for details about which parameters belong to System Setup.
1 Piano Room – Enjoying the Piano Performance – The Piano Room function is for those who want to simply, conveniently, and fully enjoy playing the instrument as a piano. No matter what settings you’ve made from the panel, you can instantly call up the optimum settings for piano performance with a single button press. You can also change the piano settings as you like. Playing a Piano Performance in the Piano Room 1 Press the [PIANO ROOM] button to call up the Piano Room display.
Making the Detailed Settings in the Piano Room You can change the settings of the Piano Room, such as touch sensitivity, as you like. 1 In the Piano Room display, use the [8UD] buttons to call up the setting display, and then change the settings by using the [1UD] – [8UD] buttons. [1UD]/ [2UD] Master Tune Determines the pitch of this instrument in 1Hz steps. [3UD]/ [4UD] Brightness Determines the brightness of the sound. Higher values result in a brighter sound.
Recording your Performance in the Piano Room In the Piano Room display, press one of the [1UD] (I) buttons to put recording in standby. 3 2 Play the keyboard to start recording. You can also start recording by using the [2UD]/[3UD] (R) buttons. While recording, “Recording” flashes. 3 After you finish your performance, press one of the [4UD]/[5UD] (J) buttons to stop recording. 4 After a message appears prompting you to save, press one of the [7UD] (Yes) buttons to save the file.
2 Voices – Playing the keyboard with various sounds – The instrument features a wide variety of exceptionally realistic instrumental Voices, including piano, guitar, strings, brass, wind instruments and more. Playing Preset Voices The Voices can be played via three keyboard parts: Main, Layer and Left.
3 Select the desired Voice by using the Cursor buttons [U][D][L][R]. You can call up the other pages by pressing the buttons ([1U] – [7U]) that correspond to the page numbers (P1, P2 ...), or by pressing the same VOICE category selection button repeatedly. Pressing the [8U] button calls up other Voice categories (folders), including the categories which do not have any VOICE category selection buttons. The Voice characteristics are indicated above the Preset Voice name. For details, see page 40.
Voice Characteristics There are various Voice types, and some types as described below require special performance considerations. These particular types have an indication above (or in the icon at left of) the Voice name on the Voice Selection display or the Main display. For explanations of the other types, refer to the Reference Manual on the website. • VRM Voices (page 41) These recreate the characteristic string resonance of a real acoustic piano. • Super Articulation (S.
Calling up the Appropriate Settings for Piano Performance (Piano Reset) You can easily reset to appropriate settings for playing the instrument as a piano, no matter what settings you’ve made from the panel. This function called “Piano Reset” allows you to play the CFX Grand Voice across the entire keyboard. NOTE This function cannot be used while the Piano Room display (page 35) is shown. Press and hold down the [PIANO ROOM] button for two seconds or longer. 2 A message appears in the display.
Playing Super Articulation Voices The Super Articulation Voices enable you to create subtle, very realistic musical expressions, simply by how you play. “S.Art!” is shown above the Voice name of Super Articulation Voices on the Voice Selection display or the Main display. Super Articulation Voice For performance instructions, you can call up the Information window of the selected Super Articulation Voice by pressing the [6D] (Info) button on the Voice Selection display.
Setting the Touch Response of the Keyboard You can adjust the touch sensitivity of the instrument (how the sound responds to the way you play the keys). This setting does not change the weight of the keyboard. 1 Call up the operation display. [MENU] → Cursor buttons [U][D][L][R] Controller, [ENTER] → TAB [R] Setting → Cursor button [U] 1 Touch Response. 2 Use the [1UD] – [7UD] buttons to set the Touch Response. [1UD]/ [2UD] Touch • Hard2: Requires strong playing to produce high volume.
Using the Metronome The [METRONOME] button lets you start or stop the metronome. The metronome provides a click sound, giving you an accurate tempo guide when you practice, or letting you hear and check how a specific tempo sounds. Metronome tempo can be adjusted by the same procedure as with Style tempo (page 52).
Fine Tuning the Pitch By default, the pitch of the entire instrument is set to 440.0 Hz according to equal temperament. This basic tuning can be changed in the display called up via [MENU] → Cursor buttons [U][D][L][R] Master Tune/Scale Tune, [ENTER]. For details, refer to the Reference Manual on the website. NOTE You can also adjust the pitch for each keyboard part (Main/Layer/Left) in the display called up via [MENU] Cursor buttons [U][D][L][R] Voice Setting, [ENTER] TAB [L][R] Tune.
2 Use the Cursor buttons [U][D] to select the page, and then use the [1UD] – [7UD] buttons to apply effects to the Voices. 1 [1UD] – [3UD] DSP Turns the DSP (Digital Signal Processor) effect on or off for each keyboard part. With the digital effects built into the instrument, you can add ambience and depth to your music in a variety of ways—such as adding reverb that makes you sound like you are playing in a concert hall. NOTE The effect type can be changed.
Advanced Features Refer to the Reference Manual on the website, Chapter 2.
3 Styles – Playing Rhythm and Accompaniment – The instrument features various accompaniment and rhythmic backing patterns (called “Styles”) in a variety of different musical genres including pop, jazz, and many others. The Style features Auto Accompaniment which detects the “chords” automatically, and lets you produce automatic accompaniment playback simply by playing the keyboard. This lets you automatically recreate the sound of a full band or orchestra — even if you’re playing by yourself.
4 Press the STYLE CONTROL [SYNC START] button to enable synchronized start (page 50). 5 As soon as you play the keyboard, the selected Style starts playback. NOTE • If you want to make the accompaniment simpler, turn the [SIMPLE] button on. Doing so enables only the rhythm and bass, and turns other parts off (page 53). • You can add variations and change the feeling of a Style by selectively turning channels on/off or by changing the Voices (page 53).
Operating Style Playback To Start/Stop Playing [START/STOP] button Starts playback of the rhythm part of the current Style. To stop playback, press this button again. Playing back both rhythm and auto accompaniment ([ACMP] button) If you turn on the [ACMP] button, both the rhythm part and auto accompaniment can be played back according to the detected chords during Style playback. NOTE • The rhythm does not sound for some Styles.
Changing Variation (Sections) During Style Playback Each Style features four different Main sections, four Fill-in sections and a Break section. By using these sections effectively, you can easily make your performance sound more dynamic and professional. The section can be freely changed while the Style is playing back. MAIN VARIATION [A] − [D] buttons Press one of the MAIN VARIATION [A] – [D] buttons to select the desired Main section (the button lights in orange).
Automatically Changing One Touch Settings with the Main Sections (OTS Link) One Touch Setting (OTS) is a convenient feature that automatically calls up the most appropriate panel settings (Voices or effects, etc.) for the currently selected Style. When the [OTS LINK] button is turned on, pressing a different MAIN VARIATION button (A − D) automatically calls up a One Touch Setting appropriate for the selected Main section.
During playback of a Style or Song, you can change the tempo by tapping the [TEMPO/TAP] button twice at the desired tempo. When Style and Song are stopped, tapping the [TEMPO/TAP] button (four times for a 4/4 time signature) starts playback of the rhythm part of the Style at the tempo you tapped. Playing Back Only the Rhythm and Bass Parts of the Style Turning Each Part (Channel) of the Style On/Off Each Style contains the channels listed below.
2 Use the [1D] – [8D] buttons to turn the channels on or off. To play only one channel by itself, hold down the appropriate button for the channel to set the channel to Solo. To cancel Solo, simply press the appropriate channel button again. To change the Voice for each channel Press one of the [1U] – [8U] buttons of the corresponding to the desired channel to call up the Voice Selection display (page 39), and then select the desired Voice.
3 Use the [2UD]/[3UD] (Unison Type) buttons to select the type of the Unison function. • All Parts: Suitable for a one-hand performance. In this type, all the accompaniment parts are played in unison with your performance. This can be used relatively easily even by a beginner. • Split: Suitable for a both-hands performance. In this type, the keyboard is divided by the Left Split Point (page 58), and the accompaniment parts suitable for each hand are played in unison with your performance independently.
Changing the Chord Fingering Type The Chord Fingering type determines how the chords are detected when you play along with Style playback with the [ACMP] button turned on. 1 Call up the operation display. [MENU] → Cursor buttons [U][D][L][R] Split Point/Chord Fingering, [ENTER] → TAB [R] Chord Fingering 2 Use the [2UD] – [4UD] buttons to select a Chord Fingering type. 2 Single Finger Allows you to easily play chords in the accompaniment range of the keyboard using only one, two or three fingers.
Detects chords in the entire key range. Chords are detected in a way similar to Fingered, even if you split the notes between your left and right hands—for example, playing a bass note with your left hand and a chord with your right, or by playing a chord with your left hand and a melody note with your right. AI Fingered Basically the same as Fingered, with the exception that less than three notes can be played to indicate the chords (based on the previously played chord, etc.).
Changing the Split Points The key which divides the keyboard into two or three areas is referred to as “Split Point.” There are two types of Split Point: “Left Split Point” and “Style Split Point.” The “Left Split Point” divides the keyboard into the Left part area and Main part area while the “Style Split Point” divides the keyboard into the Chord section for Style playback (page 49) and the Main or Left part area.
Advanced Features Refer to the Reference Manual on the website, Chapter 3.
4 Songs – Playing, Practicing and Recording Songs – For this instrument, “Song” refers to MIDI data which include preset Songs, commercially available MIDI format files, etc. Not only can you play back a Song and listen to it, but you can also play the keyboard along with Song playback and record your own performance as a Song. MIDI and Audio There are two kinds of data that can be recorded and played back on this instrument: MIDI Songs and audio files.
1 Press the SONG [SELECT] button to call up the Song Selection display. 2 3 2 Use the TAB [L][R] buttons to select the location (Preset, User or USB1) of the desired Song. NOTE • The USB1 tab appears only when a USB flash drive is connected to the [USB TO DEVICE] terminal. • The PianoRoom folder in the User tab contains the Songs recorded in the Piano Room (page 37). 3 Select the desired Song by using the Cursor buttons [U][D][L][R]. 4 Press the SONG [R/K] (Play/Pause) button to start playback.
Playback-related Operations Pause Press the [R/K] (Play/Pause) button during playback. Pressing it again resumes Song playback from the current position. Synchro Start You can start playback as soon as you play the keyboard. While playback is stopped, press the [R/K] (Play/ Pause) button and the [LL] (Rewind) button simultaneously. The [R/K] (Play/Pause) button flashes, indicating the standby status. To cancel the Synchro Start function, repeat the same operation.
Displaying Music Notation (Score) You can view the music notation (score) of the selected Song. This feature is available not only for the score of the preset Songs, but also for the Songs you’ve recorded as well as commercially available MIDI files (only those which allow devices to indicate notation). Select a Song (steps 1 − 3 on page 61). Press the SONG [SCORE/LYRICS] button to call up the Score display. If the Score display is not shown, press the [SCORE/LYRICS] button again.
Displaying Lyrics When the selected Song contains lyrics data, you can view it on the instrument’s display. 1 2 Select a Song (steps 1 − 3 on page 61). Press the SONG [SCORE/LYRICS] button to call up the Lyrics display. If the Lyrics display is not shown, press the [SCORE/LYRICS] button again. Pressing the button toggles between the Score and Lyrics displays. When the Song data contains lyrics data, the lyrics are shown on the display.
Turning Each Channel of the Song On/Off A Song consists of 16 separate channels. Usually, keyboard parts are assigned to channels 1 – 3 and Style parts are assigned to channels 9 – 16. You can independently turn each channel of the selected Song playback on or off. 1 Press the [CHANNEL ON/OFF] button several times to call up the Channel On/Off (Song) display. 2 2 Use the [1UD] – [8UD] buttons to turn each channel on or off.
3 Use the [7UD] (Play Setting) buttons to call up the Play Setting window. 4 4 Use the [6UD] (Right) buttons to turn off the right-hand part, and then use the [8UD] buttons to close the window. The right-hand part is muted and the Guide for the right-hand part is enabled. You can now play that part by yourself. NOTE • If necessary, use the [4UD] (Extra) buttons to mute the extra parts.
Repeat Playback The Song Repeat functions can be used to repeatedly play back a Song, multiple Songs, or a specific range of measures in a Song. Selecting the Repeat Mode for Song playback 1 Call up the operation display. [MENU] → Cursor buttons [U][D][L][R] Song Setting, [ENTER] → TAB [L] Play → Cursor button [U] 1 Repeat Mode 2 Use the [1UD]/[2UD] (Repeat Mode) buttons to determine the method of repeat playback. • • • • Off: Plays through the selected Song, and then stops.
NOTE • Specifying only Point A results in repeat playback between Point A and the end of the Song. • When you want to repeat from the top of the Song to a specified point in the middle: 1. Press the [A-B REPEAT] button, and then start Song playback. 2. Press the [A-B REPEAT] button again at the ending point (B). 4 Practice the specified range by playing the keyboard along with the Song repeatedly. After your practice, press the [A-B REPEAT] button to turn it off.
4 Start recording. You can start recording by playing the keyboard, starting a Style or pressing the SONG [R/K] (Play/Pause) button. NOTE You can use the metronome (page 44) while recording; however, the metronome sound will not be recorded. 5 After you finish your performance, press the [REC] button again to stop recording. A message may appear prompting you to save the recorded data. Press the [EXIT] button to close the message. To hear the recorded performance, press the [R/K] (Play/Pause) button.
3 While holding down the [REC] button, press the appropriate [1UD] – [8UD] buttons to set the desired channels to “Rec.” + When the channel is set to Rec, the following window which indicates the part assignment for the selected channel will appear. If necessary, use the Data dial to change the part assignment for the channel to be recorded. To cancel the “Rec” status of the channel, press the desired channel button.
Advanced Features Refer to the Reference Manual on the website, Chapter 4.
5 USB Audio Player/Recorder – Playback and Recording Audio Files – The convenient USB Audio Player/Recorder function allows you to play back audio files (.wav) saved to a USB flash drive — directly from the instrument. Moreover, since you can record your performances and recordings as audio files (.wav) to a USB flash drive, it is possible to play back the files on computer, share them with your friends, and record your own CDs to enjoy as well.
4 Select the desired file by using the Cursor buttons [U][D][L][R]. 5 NOTE Audio files take a slightly longer time to load than other files. Viewing Audio file information Pressing the [6D] (Info) button calls up the Information window from which you can view the file name, sample rate etc. of the selected file. NOTE If the button is not shown, press the [8D] (Close) button to call it up. 5 Press the [7D] (Audio Play) button to start playback.
USB Audio Player Setting The window called up by using the [8UD] (Setting) buttons on the USB Audio Player display allows you to make detailed settings related to Audio playback. [1UD]/ [2UD] Repeat Mode Selects the repeat mode of Audio playback. • Off: Plays through the selected file, and then stops. • Single: Plays through the selected file repeatedly. • All: Continues playback through all the files in the folder containing the current file repeatedly.
Recording Your Performance as Audio (USB Audio Recorder) You can record your performance as an audio file (WAV format — 44.1 kHz sample rate, 16-bit resolution, stereo) directly to a USB flash drive. This instrument allows you to record up to 80 minutes per single recording.
5 Start recording by using the [3UD] (R/K) buttons, and then start your performance. The elapsed recording time is shown in the display while recording. Elapsed recording time 6 NOTICE Never attempt to disconnect the USB flash drive or turn the power off during recording. Doing so may corrupt the USB flash drive data or the recording data. 6 After you finish your performance, use the [4UD] (J) buttons to stop recording.
6 Microphone – Connecting a Microphone and Singing Along with Your Performance – Connecting a Microphone 1 Before turning on the power of the instrument, turn down the [MASTER VOLUME] dial to the minimum position. 2 Connect the microphone to the [MIC INPUT] jack. Standard mono phone plug (1/4") 3 Turn on the power of the instrument, and then adjust the volume by using the [MASTER VOLUME] dial. 4 Call up the operation display.
7 Adjust the volume balance between the microphone sound and the instrument sound by using the [7UD] (Volume) buttons. If necessary, also adjust the stereo pan position of the microphone sound by using the [4UD] (Pan) buttons. Disconnecting the microphone 1. Turn down the [MASTER VOLUME] dial to “MIN.” 2. Disconnect the microphone from the [MIC INPUT] jack.
Advanced Features Making and saving the microphone settings: [MIC SETTING] → TAB [R] Setting Applying desired Effect to the microphone sound: [MIC SETTING] → TAB [L] Mixer → [8UD] (DSP) Microphone – Connecting a Microphone and Singing Along with Your Performance – Refer to the Reference Manual on the website, Chapter 6.
7 Registration Memory/Playlist – Saving and Recalling Custom Panel Setups – The Registration Memory function allows you to save (or “register”) panel settings such as Voice and Style to a Registration Memory button, and then instantly recall your custom panel settings by simply pressing a single button. When you’ve saved lots of data to the Registration Memory, use the Playlist to manage your repertoire so that you can quickly call up the desired Registration Memory for each piece of music.
Saving and Recalling Custom Panel Setups with Registration Memory Registering Your Panel Setups 1 Make the desired panel settings, such as those for Voices, Styles and Effects. Refer to Parameter Chart in the Data List on the website for a list of parameters that can be registered with the Registration Memory function. Press the REGISTRATION MEMORY [MEMORY] button to call up the Registration Memory window. You can also use the Data dial to select the items.
5 Register various panel setups to other buttons by repeating steps 1 – 4. The registered panel setups can be recalled by simply pressing the desired number button. NOTE The panel setups registered in the numbered buttons are maintained even when you turn off the power. If you want to delete all the four current panel setups, turn the power on while holding the B6 key (right-most B key on the keyboard).
Recalling a Registered Panel Setup The saved Registration Memory Bank files can be recalled by the following procedure. NOTE 1 Press the REGISTRATION MEMORY [BANK] button to call up the Registration Bank Selection display. 2 Select the desired Bank by using the Cursor buttons [U][D][L][R]. Viewing Registration Bank information You can call up the information window to confirm which Voices and Style are memorized to the [1] – [4] buttons of a Registration Memory Bank by pressing the [6D] (Info) button.
Using Playlists to Manage a Large Repertoire of Panel Setups The Playlist is useful for managing multiple set lists for your performances. You can select only the desired files from a large repertoire (the huge number of the Registration Memory Bank files) and create a new set list for each performance. Adding a Record (Link to a Bank file) to a Playlist By adding Records to a Playlist, you can directly recall desired Registration Memory Bank files from the Playlist for each performance.
3-3 Pressing the [7D] (OK) button closes the display, and the new Records are added to the bottom of the Playlist. To add a Record by using the search function: 3-1 Use the [2UD] (Search) buttons to call up the Playlist Record Search display. 3-2 If necessary, use the [1UD]/[2UD] (Update) buttons to update the data used for searching.
5 Save all Records as a single Playlist file. 5-1 Use the [8UD] (Option) buttons to call up the operation window. 5-2 Use the [7UD] (Select & Save) buttons to call up the Playlist File Selection display. 5-3 Save the Records as a file by following the instructions on page 26. Recalling Custom Panel Setups via the Playlist 1 From the Playlist display, use the [8UD] (Option) buttons to call up the operation window. Registration Memory number called up when the Record is loaded.
1 On the Playlist display, move the cursor to the desired Record for moving by using the Cursor buttons [U][D]. 2 Press the [6U]/[7U] (Move) button to move the Record upward in the list, or the [6D]/[7D] (Move) button to move the Record downward. 3 Save the edited Playlist file (step 5 on page 86). Deleting the Record from the Playlist 1 On the Playlist display, move the cursor to the desired Record to delete by using the Cursor buttons [U][D].
8 Mixer – Editing the Volume and Tonal Balance – The Mixer gives you intuitive control over aspects of the keyboard parts and Song/Style channels, including volume balance and the timbre of the sounds. It lets you adjust the levels and stereo position (pan) of each Voice to set the optimum balance and stereo image, and lets you set how the effects are applied. Basic Procedure 1 2 Press the [MIXER/EQ] button to call up the Mixer display.
Song1–8, Song9–16 3 Select this when you want to adjust the balance among all the parts (channels) of the Song. Use the TAB [L][R] buttons to select the page for the parameters to be edited. Volume/Pan For adjusting volume and panning for each part and changing the Voice. Filter For adjusting the Harmonic Content (resonance) and sound brightness for each part. Effect For selecting an effect type and adjusting its depth for each part.
To save the Song settings: First register the edited settings as part of the Song data (Setup data), and then save the Song to the User drive or USB flash drive. If you want to recall the settings for future use, select the Song file saved here. 1. Call up the operation display. [MENU] → Cursor buttons [U][D][L][R] Song Creator, [ENTER] 2. Use the TAB [L][R] buttons to select the Setup tab. 3.
9 Connections – Using Your Instrument with Other Devices – CAUTION Before connecting the instrument to other electronic components, turn off the power of all the components. Also, before turning any components on or off, make sure to set all volume levels to minimum (0). Otherwise, damage to the components, electrical shock, or even permanent hearing loss may occur. NOTICE Do not place any external devices in an unstable position. Doing so may cause the device to fall and result in damage.
Formatting a USB Flash Drive When a USB flash drive is connected, a message may appear indicating that the connected USB flash drive is not formatted. If so, execute the format operation. NOTICE The Format operation deletes any previously existing data. Make sure that the USB flash drive you are formatting does not contain important data. 1 2 Connect a USB flash drive for formatting to the [USB TO DEVICE] terminal. Call up the operation display.
NOTE • When using a USB cable to connect the instrument to your computer, make the connection directly without passing through a USB hub. • The instrument will begin transmission a short time after the USB connection is made. Transmitting/Receiving Audio Data (USB Audio Interface function) By connecting a computer or a smart device to the [USB TO HOST] terminal via a USB cable, digital audio data can be transmitted/received.
Connecting to a Smart Device ([AUX IN] jack/Bluetooth/[USB TO HOST] terminal/Wireless LAN) Connecting a smart device such as a smart phone or tablet provides the following advantages: • By connecting via the [AUX IN] jack (page 95) or Bluetooth (page 96), you can hear the sound output from the smart device through the built-in speakers of the instrument. • By connecting via the [USB TO HOST] terminal, you can transmit/receive audio data (USB Audio Interface function; page 93).
Listening to Audio Playback by an External Device through the Instrument’s Speaker ([AUX IN] jack/Bluetooth/[USB TO HOST] terminal) Audio playback by the connected device can be output from the instrument’s speaker. To input audio, connect an external device by one of the following methods.
Listening to Audio data from a Bluetooth-equipped device through this instrument (Bluetooth Audio Function) Before using the Bluetooth function, be sure to read “About Bluetooth” on page 97. You can play the sound of audio data saved in a Bluetooth-equipped device, such as a smartphone or portable audio player, on this instrument and listen to it through the built-in speaker of the instrument.
3 Use the [6UD]/[7UD] (Paring) buttons to pair with a Bluetooth-equipped device. If you wish to connect your Bluetooth-equipped device to the instrument, the device needs to be paired with the instrument first. Once the device has been paired with this instrument, there is no need to perform pairing again. You can also start paring simply by holding down the [MENU] button for 3 seconds (with no need to call up the Bluetooth display).
Connecting Headphones or an External Speaker ([PHONES/OUTPUT] jack) The [PHONES/OUTPUT] jack can be used to connect headphones, as well as for sending the output signal to the connected device, such as a speaker, recorder or computer. The speakers of this instrument are automatically shut off when a plug is inserted into this jack. CAUTION Do not use the instrument/device or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss.
Connecting a Foot Pedal ([AUX PEDAL] jack) The included footswitch or other separately sold foot pedals (FC3A, FC4A or FC5) can be connected to the [AUX PEDAL] jack. For details, refer to page 14. NOTE • Make sure that power is off when connecting or disconnecting the pedal. • Do not press the footswitch while turning the power on. Doing this changes the recognized polarity of the pedal, resulting in reversed operation.
10 Menu – Making Global Settings and Using Advanced Features – The Menu provides a variety of convenient settings and tools for the instrument. These include general settings that affect the entire instrument, as well as detailed settings for specific functions. Also included are advanced Creator features, such as for creating your own Styles and Songs. Basic Procedure This section covers only how to call up the operation display for each function.
Function List Menu1 Split Point/ Chord Fingering Keyboard Harmony Regist Sequence/ Freeze Controller Voice Setting Description Reference Manual Split Point Determines the Split Point and Chord Detection Area. Page 58 Chapter 3 Chord Fingering Determines the Chord Fingering type. Page 56 Chapter 3 Page 46 Chapter 2 For selecting the Keyboard Harmony type and making related settings. This display can also be called up via [VOICE EFFECT] Cursor button [D] 2 Keyboard Harmony [4UD] (Type).
Menu2 Description Config 1, 2 Utility For making general settings such as speaker output, AUX In Noise Gate, Audio Loopback, Stereophonic Optimizer, and IAC, etc. Owner’s Manual Reference Manual Pages 17, 93, 95, 98 Chapter 10 – Chapter 10 Determines the parameters (effect, Split Point, etc.) that are to Parameter Lock remain unchanged when the panel setups are changed via Registration Memory, One Touch Setting, etc.
Troubleshooting Overall A click or pop is heard when the power is turned on or off. This is normal. Electrical current is being applied to the instrument. The power is automatically turned off. This is normal and due to the Auto Power Off function. If necessary, set the parameter of the Auto Power Off function (page 18). Noise is heard from the instrument’s speakers. Noise may be heard if a mobile phone is used near the instrument or if the phone is ringing.
Overall An existing file is not shown. • The file extension (.MID, etc.) may have been changed or deleted. Manually rename the file, adding the appropriate extension, on a computer. • Data files with names of more than 50 characters cannot be handled by the instrument. Rename the file, reducing the number of characters to 50 or less. Voice The Voice selected from the Voice Selection display does not sound. Turn on the PART ON/OFF button for the desired part (page 38).
USB Audio Player/Recorder A message indicating the drive is busy appears, and the recording is aborted. • Make sure to use a compatible USB flash drive (page 91). • Make sure that the USB flash drive has enough memory (page 92). • If you are using a USB flash drive to which data has already been recorded, check first that no important data remains on the device, and then format it (page 92) and try recording again. Audio files cannot be selected. The file format may not be compatible with the instrument.
Specifications Product Name Size/Weight Digital Piano Dimensions (W × D × H) Weight Control Interface Keyboard 21.4 kg (47 lb, 3 oz) Number of Keys Type Touch Response Other Controllers Pitch Bend Wheel Display 4.
Functions Recording Time (max.) Format WAV (44.1 kHz, 16-bit, stereo) Recording WAV (44.1 kHz, 16-bit, stereo) Time Stretch Yes Pitch Shift Yes Vocal Cancel Yes Piano Room Yes Registration Memory Number of Buttons Playlist Number of Records (max.) Control Lesson/Guide Overall Controls Metronome Tempo Range Transpose Tuning Scale Type Bluetooth (May not have this functionality depending on the country in which you purchased the product.) Yes 5 – 500, Tap Tempo -12 – 0 – +12 414.8 – 440.
Compatible Format GM2 “GM (General MIDI)” is one of the most common Voice allocation formats. “GM System Level 2” is a standard specification that enhances the original “GM” and improves Song data compatibility. It provides for increased polyphony, greater Voice selection, expanded Voice parameters, and integrated effect processing.
Index [1UD] – [8UD] buttons ...................................................20 A A-B Repeat ....................................................................... 67, 73 Accent ......................................................................................55 Accessories ................................................................................7 Accompaniment ....................................................................48 Adaptive Style ...............................................
N Name .......................................................................................28 Noise Gate ...............................................................................95 O One Touch Setting (OTS) .....................................................52 OTS Link .................................................................................52 Owner Name ..........................................................................18 P Panel Setup (Panel Settings) ..........................
Apache License 2.0 Copyright (c) 2009-2018 Arm Limited. All rights reserved. SPDX-License-Identifier: Apache-2.0 Licensed under the Apache License, Version 2.0 (the License); you may not use this file except in compliance with the License. You may obtain a copy of the License at www.apache.org/licenses/LICENSE-2.
Important Notice: U.S. LIMITED WARRANTY for Customers in the United States For detailed information about this Yamaha product and warranty service, please either visit the following website address (printable file is available at our website) or contact Customer Service at the address or telephone number identified below. Website Address: yamaha.io/DGXWarranty Customer Service: Yamaha Corporation of America 6600 Orangethorpe Avenue, Buena Park, CA 90620-1273 Telephone: 800-854-1569 For U.S.A.
For EU countries BG Bulgarian ОПРОСТЕНА ЕС ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ LV Latvian VIENKĀRŠOTA ES ATBILSTĪBAS DEKLARĀCIJA С настоящото Yamaha Music Europe GmbH декларира, че този тип радиосъоръжение [DGX-670] е в съответствие с Директива 2014/53/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: https://europe.yamaha.com/en/support/compliance/doc.html Ar šo Yamaha Music Europe GmbH deklarē, ka radioiekārta [DGX-670] atbilst Direktīvai 2014/53/ES.
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Yamaha Canada Music Ltd. 135 Milner Avenue, Toronto, Ontario M1S 3R1, Canada Tel: +1-416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Avenue, Buena Park, CA 90620, U.S.A.
Yamaha Global Site https://www.yamaha.com/ Yamaha Downloads https://download.yamaha.com/ Manual Development Group © 2020 Yamaha Corporation Published 06/2020 MWMA*.
