Owner’s Manual Keyboard Stand Assembly For information on assembling the keyboard stand, refer to the instructions on page 10 of this manual.
SPECIAL MESSAGE SECTION This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by Yamaha. WARNING: Do not place this product in a position where anyone could walk on, trip over, or roll anything over power or connecting cords of any kind.
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Power supply/AC power adaptor Water warning • Only use the voltage specified as correct for the instrument.
Connections Saving data • Before connecting the instrument to other electronic components, turn off the power for all components. Before turning the power on or off for all components, set all volume levels to minimum. Also, be sure to set the volumes of all components at their minimum levels and gradually raise the volume controls while playing the instrument to set the desired listening level.
Copyright Notice The followings are the titles, credits and copyright notices for three (3) of the songs pre-installed in this electronic keyboard: Mona Lisa from the Paramount Picture CAPTAIN CAREY, U.S.A.
Congratulations and thank you for purchasing the Yamaha DGX-630/YPG-635 Portable Grand! Please read this owner’s manual carefully before using the instrument in order to take full advantage of its various features. Make sure to keep this manual in a safe and handy place even after you finish reading, and refer to it often when you need to better understand an operation or function. Included Accessories The DGX-630/YPG-635 package includes the following items. Please check that you have them all.
Special Features of the DGX-630/YPG-635 Graded Hammer Standard Keyboard Thanks to our experience as the world’s leading manufacturer of acoustic pianos, we’ve developed a keyboard with action that’s virtually indistinguishable from the real thing. Just as on a traditional acoustic piano, the keys of the lower notes have a heavier touch, while the higher ones are more responsive to lighter playing. The keyboard’s sensitivity can even be adjusted to match your playing style.
Contents Copyright Notice ....................................................................... 6 Panel Logos ............................................................................. 6 Included Accessories ............................................................... 7 Special Features of the DGX-630/YPG-635............................. 8 Setting Up 10 Keyboard Stand Assembly................................. 10 Power Requirements ..............................................................
Setting Up Keyboard Stand Assembly CAUTION Read these cautions carefully before you assemble or use the keyboard stand. These cautions are to promote safe use of the stand and to prevent injury and damage from occurring to you and others. By following these cautions carefully, your keyboard stand will provide you with safe and prolonged use. • Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble in accordance with the sequence given below.
Setting Up x Attach the stand bases. 2 q Joint connectors Insert the joint connectors q into the stand boards as shown. The joint connectors have been installed properly if you can see the screw head on the connector. NOTE • If you put the connectors in wrong direction and want to take them out, tap around the holes on the boards. w 6 x 70 mm roundhead screws 3 e 6 x 30 mm roundhead screw Attach the stand bases to the bottom of the side boards, using the screws w.
Setting Up b Put the keyboard on the stand. 5–6 Check the back-to-front orientation for stand, and carefully place the keyboard on the side boards. Slowly move the keyboard so that the holes on the bottom of the keyboard are properly aligned with the holes on the angle brackets. CAUTION • Be careful not to drop the keyboard or to get your fingers caught between the keyboard and the stand parts. n Install the keyboard to the stand. y 5 x 16 mm Fix the keyboard to the angle brackets, using the screws y.
Setting Up Be sure to do the following operations BEFORE turning on the power. Power Requirements Make sure that the [STANDBY/ON] switch of the instrument is set to STANDBY. Plug the AC adaptor into an AC outlet. CAUTION WARNING • Use the specified adaptor (PA-5D or an equivalent recommended by Yamaha) only. The use of other adaptors may result in irreparable damage to both the adaptor and the instrument. • Unplug the AC Power Adaptor when not using the instrument, or during electrical storms.
Setting Up Connecting a Pedal Unit (PEDAL UNIT jack) This jack is for connecting an optional LP-7 pedal unit. When connecting the pedal unit, make sure to also assemble the unit on the supplied keyboard stand. NOTE • Make sure that power is OFF when connecting or disconnecting the pedal. LP-7 (optional) Keyboard Stand Pedal Unit Functions The optional pedal unit has three foot pedals that produce a range of expressive effects similar to those produced by the pedals on an acoustic piano.
Setting Up Connecting to a Computer (USB Terminal) Connect the instrument’s USB terminal to the USB terminal of a computer, and you can transfer performance data and song files between the two (page 105). To use the USB data-transfer features you’ll need to do the following: • First, make sure the POWER switch on the instrument is set to OFF, then use an AB type USB cable to connect the instrument to the computer. After making the connections, turn the instrument’s power on.
Panel Controls and Terminals Front Panel Song Category List (page 35) Style Category List (page 134) u e i o q r y t w !1 !0 !2 !3 !4 !5 !6 !7 !8 !9 Front Panel 16 DGX-630/YPG-635 Owner’s Manual r !9 [START/STOP] button ...............pages 27, 34, 67 @0 [SONG] button ........................................ page 33 @1 [EASY SONG ARRANGER] button ............................... page 58 @2 [STYLE] button ....................................... page 27 @3 [VOICE] button...............
Panel Controls and Terminals Display (pages 68, 69) Music Database List (page 135) Voice Category List (page 128) @7 @0 @1 @4 @2 @3 @6 @5 #0 @8 #1 #2 #3 @9 #4 #5 Rear Panel #6 #7 #8 #9 $0 $1 Rear Panel #6 CONTRAST knob ....................................page 69 #7 USB TO DEVICE terminal........................page 97 USB TO HOST terminal .........................page 105 #8 SUSTAIN jack...........................................page 13 #9 PEDAL UNIT jack............................
e d ck Gui ui Q Changing the Display Language Quick Guide This instrument allows you to select English or Japanese as the display language. The default display language is English, but if you switch to Japanese the lyrics, file names, demo display, and some messages will be displayed in Japanese where appropriate. 2 Press the CATEGORY [ ] and [ ] buttons a number of times until the “Language” item appears. r Press the [FUNCTION] button.
e d ck Gui ui Q Try Playing a Variety of Instrument Voices In addition to piano, organ, and other “standard” keyboard instruments, this instrument has a large range of voices that includes guitar, bass, strings, sax, trumpet, drums and percussion, sound effects … a wide variety of musical sounds. Select and Play a Voice—MAIN This procedure selects the main voice you will play on the keyboard. 1 Press the [VOICE] button. The main voice selection display will appear.
Try Playing a Variety of Instrument Voices Play Two Voices Simultaneously—DUAL You can select a second voice which will play in addition to the main voice when you play the keyboard. The second voice is known as the “dual” voice. 1 Press the [DUAL ON/OFF] button. The [DUAL ON/OFF] button turns the dual voice on or off. When turned on the dual voice “DUAL” will appear in the MAIN display. The currently selected dual voice will sound in addition to the main voice when you play the keyboard.
Try Playing a Variety of Instrument Voices 4 Play the keyboard. Two voices will sound at the same time. Try selecting and playing a range of dual voices. Press the [EXIT] button to return to the MAIN display. Play Different Voices with the Left and Right Hands—SPLIT In the split mode you can play different voices to the left and right of the keyboard “split point”.
Try Playing a Variety of Instrument Voices 3 Select the desired split voice. 4 Play the keyboard. Watch the highlighted split voice and rotate the dial until the voice you want to use is selected. The voice selected here becomes the split voice which will play to the left of the keyboard split point. For this example try selecting the “041 Folk Guitar” voice. Try selecting and playing a range of split voices. Press the [EXIT] button to return to the MAIN display.
Fun Sounds This instrument includes a range of drum kits and unique sound effects you can use for entertainment. Laughter, babbling brooks, jet fly-bys, eerie effects, and much more. These sounds can be a great way to enhance the mood at parties. Drum Kits Drum kits are collections of drum and percussion instruments. When you select a violin or other normal instrument main voice, for example, all keys produce the sound of the same violin, only at different pitches.
e d ck Gui ui Q The Metronome The instrument includes a metronome with adjustable tempo and time signature. Play and set the tempo that is most comfortable for you. Start the Metronome Turn the metronome on and start it by pressing the [METRONOME ON/OFF] button. To stop the metronome, press the [METRONOME ON/OFF] button again. 4/4 Current setting Adjusting the Metronome Tempo 1 Press the [TEMPO/TAP] button to call up the tempo setting. Tempo 2 24 Use the dial to select a tempo from 5 to 280.
The Metronome Setting the Number of Beats per Measure, and the Length of Each Beat In this example we’ll set up a 5/8 time signature. 1 Press and hold the [METRONOME ON/OFF] button for longer than a second to select the function “Time Signature–Numerator”. Hold for longer than a second Numerator (Number of beats per measure.) Denominator (The length of one beat.) The available range is from 1 through 60. Select 5 for this example. A bell accent will be sounded at the first beat of each measure.
The Metronome Setting the Click bell sound This allows you to select whether the click sound has a bell accent, or plays only a click sound. 3 You can then use the [+] and [-] buttons to turn the bell sound on or off. r 2 Use the CATEGORY [ ] and [ ] buttons to select the Bell item. f 1 Press the [FUNCTION] button. Adjusting the Metronome Volume r 2 Use the CATEGORY [ ] and [ ] buttons to select the Metronome Volume item. f 1 Press the [FUNCTION] button.
e d ck Gui ui Q Playing Styles This instrument has an auto accompaniment feature that produces accompaniment (rhythm + bass + chords) in the style you choose to match chords you play with your left hand. You can select from 160 different styles covering a range of musical genres and time signatures (see page 134 for a complete list of the available styles). In this section we’ll learn how to use the auto accompaniment features. Select a Style Rhythm Most styles includes a rhythm part.
Playing Styles Play Along with a Style You learned how to select a style rhythm on the preceding page. Here we’ll see how to add bass and chord accompaniment to the basic rhythm to produce a full, rich accompaniment that you can play along with. 1 2 Press the [STYLE] button and select the desired style. Turn automatic accompaniment on. Press the [ACMP ON/OFF] button. Pressing this button a second time will turn automatic accompaniment off. This icon appears when automatic accompaniment is on.
Playing Styles When sync start is on, the bass and chord accompaniment included in a style will start playing as soon as you play a note to left of the keyboard split point. Press the button a second time to turn the sync start function off. 4 Play a left-hand chord to start the style. You can still “play” chords even if you don’t actually know any chords. This instrument will recognize even a single note as a chord. Try playing from one to three notes at the same time to the left of the split point.
Playing Styles Styles Are More Fun When You Understand Chords Chords, created by playing multiple notes at the same time, are the basis for harmonic accompaniment. In this section we’ll take a look at sequences of different chords played one after another, or “chord sequences.” Since each chord has it’s own unique “color”—even if it’s different fingerings of the same chord—the chords you choose to use in your chord progressions have a huge influence on the overall feel of the music you play.
Playing Styles Recommended Style 148 Piano Boogie —3-chord boogie-woogie— Press the [INTRO/ENDING/rit.] button. C F C G F C Press the [INTRO/ENDING/rit.] button. This progression provides varied harmonic backing with just three chords. When you get a feel for the progression in the score, try changing the order of the chords! Recommended Style 096 Bossa Nova —Bossa nova with jazz-style chords— Press the [INTRO/ENDING/rit.] button.
Playing Styles Playing Auto-accompaniment Chords There are two ways of playing auto-accompaniment chords: ● Easy Chords ● Standard Chords The instrument will automatically recognize the different chord types. The function is called Multi Fingering. Press the [ACMP ON/OFF] button to turn auto-accompaniment on (page 28). The keyboard to the left of the split point (default: 54/F#2) becomes the “accompaniment range”. Play the accompaniment chords in this area of the keyboard.
e d ck Gui ui Q Using Songs With this instrument the term “song” refers the data that makes up a piece of music. You can simply enjoy listening to the 30 internal songs, or use them with just about any of the many functions provided—the performance assistant technology feature, lessons, and more. The songs are organized by category. In this section we’ll learn how to select and play songs, and briefly describe the 30 songs provided.
Using Songs 3 Listen to the song. Press the [START/STOP] button to begin playback of the selected song. You can stop playback at any time by pressing the [START/STOP] button again. Song start! Song Fast Forward, Fast Reverse, and Pause These are just like the transport controls on a cassette deck or CD player, letting you fast forward [FF], rewind [REW] and pause [PAUSE] playback of the song. REW Press the fast reverse button to rapidly return to an earlier point in the song.
Using Songs Play the Demo Song Press the [DEMO] button. The demo song will start playing. Listen to some of the outstanding instrument voices provided! The demo song will automatically repeat from the beginning after it has played all the way through. You can stop demo playback at any time by pressing the [START/STOP] button.
Using Songs Types of Songs The following three types of songs can be used by the DGX-630/YPG-635. ● Preset Songs (the 30 songs built into the instrument) ................Song numbers 001–030. ● User Songs (recordings of your own performances) ..................Song numbers 031–035. ● External song files (song data transferred from a computer*) ...Song numbers 036–. * The Accessory CD-ROM includes a selection of 70 MIDI songs. See page 109 for instructions on how to transfer the songs to the instrument.
Using Songs Displaying the Song Score This instrument is capable of display the scores of songs. Scores are displayed for the 30 internal preset songs as well as songs in SMF format stored in a USB fl ash memory or the instrument’s internal flash memory. 1 2 Select a song. Follow steps 1 and 2 of the procedure described on page 33. Press the [SCORE] button and a single-staff score will appear. There are two types of score display: single-staff and double-staff.
Using Songs Display the Lyrics If a song contains lyric data, the lyrics can be made to appear on the display. No lyrics will be displayed for a song that contains no lyric data even if the [LYRICS] button is pressed. 1 Select a song. 2 Press the [LYRICS] button. Select a song between 16, 20, and 30 by performing steps 1 and 2 described on page 33. The title, lyricist, and composer of the song will appear on the display.
e d ck Gui ui Q The Easy Way to Play Piano This instrument includes a performance assistant technology feature that lets you play along with a song and sound like a great pianist (even though you might be making lots of mistakes)! In fact, you can play any notes and still sound good! You could even just tap one key and the results would be a beautiful melody. So even if you can’t play piano and can’t read a note of music, you can have some musical fun.
The Easy Way to Play Piano CHORD Type—Play with Both Hands 1 Press the [P.A.T. ON/OFF] button. This turns on the performance assistant technology feature. The currently selected type is shown in the MAIN display when the performance assistant technology feature is on. The currently selected type 2 Select the CHORD type. Hold for longer than a second Select Chord Press and hold the [P.A.T. ON/OFF] button for longer than a second so that the performance assistant technology type appears.
The Easy Way to Play Piano 4 Press the [START/STOP] button. Song playback will begin. The basic pattern will play repeatedly. Listen to the basic pattern for four measures while getting a feel for the basic pattern, then begin playing yourself from the fifth measure. The keys you should play will be shown in the display. 5 Play on the keyboard. Before After Try playing the score on the left with both hands. You can even play the same keys over and over: C, E, G, C, E, G, C, E.
The Easy Way to Play Piano CHORD/FREE Type—Applying the Chord Type to the Left Hand Only 1 Press the [P.A.T. ON/OFF] button. This turns on the performance assistant technology feature. The currently selected type is shown in the MAIN display when the performance assistant technology feature is on. The currently selected type 2 Select the CHORD/FREE type. Hold for longer than a second Select Chord/Free Press and hold the [P.A.T.
The Easy Way to Play Piano 4 Press the [START/STOP] button. Song playback will begin. The left-hand keys you should play will be shown on the display. 5 Play on the keyboard. Play to the right of the split point with your right hand, and to the left of the split point with your left hand. Split point With this type notes played on the left-hand side of the split point will actually sound an octave higher. Play the Nocturne melody with your right hand.
The Easy Way to Play Piano MELODY Type—Play with One Finger See page 48 for some hints on how to play melodies. 1 Press the [P.A.T. ON/OFF] button. This turns on the performance assistant technology feature. The currently selected type is shown in the MAIN display when the performance assistant technology feature is on. The currently selected type 2 Select the MELODY type. Select Melody Hold for longer than a second Press and hold the [P.A.T.
The Easy Way to Play Piano 4 Press the [START/STOP] button. Song playback will begin. Because the Melody type has been selected, the song melody will not sound. You can enjoy playing the melody yourself (step 5). Song start! 5 Play on the keyboard. To begin, try to feel the rhythm of the song. Then tap a key with one finger of your right hand in time with the music. You can play any key.
The Easy Way to Play Piano CHORD/MELODY—Chord Type with the Left Hand, Melody with the Right 1 Press the [P.A.T. ON/OFF] button. This turns on the performance assistant technology feature. The currently selected type is shown in the MAIN display when the performance assistant technology feature is on. The currently selected type 2 Select the CHORD/MELODY type. Hold for longer than a second Select Chord/Melody Press and hold the [P.A.T.
The Easy Way to Play Piano 4 Press the [START/STOP] button. Song playback will begin. The basic pattern will repeat. Listen to eight measures while memorizing the basic pattern. It’s your turn to play the part from the ninth measure. 5 Play on the keyboard. Play to the right of the split point with your right hand, and to the left of the split point with your left hand. Split point With this type notes played on the left-hand side of the split point will actually sound an octave higher.
The Easy Way to Play Piano Use the Performance Assistant to Play Like a Pro! Here are a few hints for using the Chord type. If you select Chord/Free or Chord/Melody, the left-hand section of the keyboard becomes the Chord type section, so use these hints on the lefthand section of the keyboard. To begin, try to feel the rhythm of the song. Then, with your hands spread as shown in the illustration, simply play the keyboard alternately with your left and right hands (any notes will do).
The Easy Way to Play Piano Make Use of the Score in the Melody Type. If you want to play the melody with the correct rhythm, use the onscreen score feature. Displaying the Score. After performing steps 1 to 4 on page 44, press the [SCORE] button. The melody score will appear. Appears when the performance assistant technology is on Marker Chord Melody The marker will indicate the current position in the score during playback.
e d ck Gui ui Q Select a Song For a Lesson Yamaha Education Suite You can select song you like and use it for a left-hand, right-hand, or both-hands lesson. You can also use songs (only SMF format 0/1) transferred to the instrument from a computer. (page 108) During the lesson you can play as slowly as you like, and you can even play wrong notes. Song playback will slow down to a speed you can handle.
Select a Song For a Lesson Lesson 1—Waiting In this lesson, try playing the correct notes. Play the note shown in the display. The song will wait until you play the right note. 1 Select a song for your lesson. 2 Press [EXIT] button to return to the MAIN display. 3 Select the part you want to practice. Press the [SONG] button, and rotate the dial to select the song you want to use for your lesson. As listed on page 35 there are a variety of song types.
Select a Song For a Lesson 4 Start Lesson 1. Press the LESSON [START] button to select Lesson 1. Each time the LESSON [START] button is pressed the lesson modes are selected in sequence: Lesson 1 → Lesson 2 → Lesson 3 → Off → Lesson 1 ... An explanation of the selected lesson will appear on the display for a few seconds before the lesson begins. In this case the “R1” indicates that righthand lesson 1 has been selected.
Select a Song For a Lesson ● Shifting the keyboard left or right. The hidden ( ) areas of the keyboard can be brought into view by pressing the [+] or [-] button. The displayed range (61 keys) Actual keyboard range (DGX-630/YPG-635 = 88 keys) 61 keys of the keyboard’s range are shown on the display. The DGX-630/ YPG-635 actually have 88 keys. In some songs that include very high or low notes, those notes may fall outside the displayed range and may not be shown on the display.
Select a Song For a Lesson Lesson 2—Your Tempo Learn to play the correct notes with the correct timing. Song playback tempo will vary to match the speed you are playing at. The song will slow down when you play wrong notes, so you can learn at your own pace. 1 Select the song and part you want to practice (steps 1 and 3 on page 51). 2 Start Lesson 2. Each time the LESSON [START] button is pressed the lesson modes are selected in sequence: Lesson 1 → Lesson 2 → Lesson 3 → Off → Lesson 1 ...
Select a Song For a Lesson Lesson 3—Minus One Here’s where you can perfect your technique. The song will play at the normal tempo, minus the part you have chosen to play. Play along while listening to the song. 1 Select the song and part you want to practice (steps 1 and 3 on page 51). 2 Start Lesson 3. Each time the LESSON [START] button is pressed the lesson modes are selected in sequence: Lesson 1 → Lesson 2 → Lesson 3 → Off → Lesson 1 ...
Select a Song For a Lesson Practice Makes Perfect—Repeat and Learn Use this feature when you want to start again just ahead of a section on which you made a mistake, or to repeatedly practice a section you find difficult. Press the [REPEAT & LEARN] button during a lesson. The song location will move back four measures from the point at which you pressed the button, and playback will begin after a one-measure count-in.
e d ck Gui ui Q Play Using the Music Database You want to play music in your favorite style, but you’re not sure how to select the best voice and style for the type of music you want to play ... simply select the appropriate style from the Music Database. The panel settings will automatically be adjusted for the ideal combination of sounds and style! 1 Press the [MUSIC DATABASE] button. A Music Database list will appear in the display. 2 Select a Music Database.
e d ck Gui ui Q Change a Song’s Style In addition to each song’s default style, you can select any other style to play the song with the Easy Song Arranger feature. This means that you can play a song that is normally a ballad, for example, as a bossa nova, as a hip-hop tune, etc. You can create totally different arrangements by changing the style with which a song is played. You can also change the song’s melody voice and the keyboard voice for a complete change of image.
Change a Song’s Style 3 Listen to the song. NOTE Press the [START/STOP] button to begin playback of the song. Move on to the next step while the song is playing. • When playing song numbers 010, 011, and 020 to 030 while using the Easy Song Arranger, melody tracks will be automatically muted and no melody will sound. In order to hear the melody tracks you will need to press the SONG MEMORY buttons [3] to [5]. Song start! 4 Press the [EASY SONG ARRANGER] button. The Style Select display will appear.
e d ck Gui ui Q Record Your Own Performance You can record up to 5 of your own performances and save them as user songs 031 through 035. Once your performances have been saved as user songs they can be played in the same way as the internal songs. User songs can also be saved to a USB flash memory device, as described on page 100. ■ Recordable Data 5 melody tracks and 1 Style (chord) track can be recorded.
Record Your Own Performance Recording Procedure 1 From the MAIN display press the [SONG] button, then use the dial to select the user song number (031–035) you want to record to. Rotate the dial to select a song number between 031 and 035. 2 Select the track(s) you want to record to and confirm your selection on the display. ◆ Record a Melody Track and the Accompaniment Track Together Press the melody track button [1]–[5] you want to record to while holding the [REC] button.
Record Your Own Performance 3 Recording will start when you play on the keyboard. You can also start recording by pressing the [START/STOP] button. The current measure will be shown on the display during recording. Current measure NOTE • If the memory becomes full during recording a warning message will appear and recording will stop automatically. Use the song clear or track clear (page 63) function to delete unwanted data and make more room available for recording, then do the recording again.
Record Your Own Performance ● To Record Other Tracks Repeat steps 2 through 5 to record any of the remaining tracks. By selecting an unrecorded track—SONG MEMORY buttons [1]–[5], [A]—you can record the new track while listening to previously recorded tracks (the border around the track number will appear in the display). You can also mute previously recorded tracks (the border around the track number disappears in the display) while recording new tracks.
Record Your Own Performance 3 Press the [+] button to clear the song. The clear-in-progress message will appear briefly on the display while the song is being cleared. Track Clear—Deleting a Specified Track from a User Song This function lets you delete a specified track from a user song. 1 2 From the MAIN display select the user song (031–035) you want to clear. Press and hold the SONG MEMORY track button ([1]–[5], [A]) corresponding to the track you want to clear for longer than a second.
Backup and Initialization Backup The following settings are always backed up, and are maintained even when the power is turned off. If you want to initialize the settings, use the Initialize operation as explained below.
Basic Operation Basic Operation Overall DGX-630/YPG-635 control is based on the following simple operations. 1 Press a button to select a basic function. 2 Use the dial to select an item or value. 3 Start a function. 3 Start a function. 1 Select a basic function. 2 Select an item or value. Display (pages 68, 69) ● Volume Adjustment Adjusts the volume of the sound heard via the instrument’s speakers or a pair of headphones plugged into the PHONES jack. Rotate counterclockwise to lower the volume.
Basic Operation 2 Use the dial to select an item or value When you select a basic function, the item corresponding to that function will be listed in the display. You can then use the dial or the number buttons [0]–[9] to select the desired item. The currently selected item is highlighted in the display. In this example the [VOICE] button has been pressed.
Basic Operation The Displays ● Display Names All operations are carried out while watching the display. A number of display types are provided for different modes and functions. The name of the current display appears at the top of the display. ● MAIN Display Title To Return To the MAIN Display Most basic operations are carried out from the instrument’s MAIN display. You can return to the MAIN display from any other display by pressing the [EXIT] button near the lower right corner of the display panel.
Basic Operation MAIN Display Items The MAIN display shows all of the current basic settings: song, style, voice. It also includes a range of indicators that show the on/off status of a range of functions. * Adjust the LCD CONTRAST control on the rear panel of the instrument for optimum display legibility. A-B Repeat Tempo Appears when repeat playback is engaged. Transpose Measure Number Function ON/Off Icons Dual Appears when the Dual Voice is on.
Reference e erenc ef R Play with a Variety of Effects Adding Harmony This feature adds harmony notes to the main voice. 1 Press the [HARMONY ON/OFF] button to turn Harmony feature on. To turn Harmony off, press the [HARMONY ON/OFF] button again. Hold for longer than a second. The currently selected harmony type When harmony is on the harmony icon will appear in the display.
Play with a Variety of Effects Adding Reverb Reverb lets you play with a rich concert hall type ambience. When you select a style or song the optimum reverb type for the voice used is automatically selected. If you want to select a different reverb type, use the procedure described below. Refer to the Effect Type List on page 138 for information about the available reverb types. 1 Press the [FUNCTION] button to call up the FUNCTION display. 2 Use the CATEGORY [ 3 Use the dial to select a reverb type.
Play with a Variety of Effects Adding Chorus The chorus effect creates a thick sound that is similar to many of the same voices being played in unison. When you select a style or song the optimum chorus type for the voice used is automatically selected. If you want to select a different chorus type, use the procedure described below. 1 Press the [FUNCTION] button to call up the FUNCTION display. 2 Use the CATEGORY [ 3 Use the dial to select a chorus type.
Play with a Variety of Effects Adding DSP DSP is term of abbreviated form of Digital Signal Processor. The DSP effect can be added to the Main and Dual Voices. These range from reverb-like ambience effects to distortion and other dynamic processing tools that let you enhance the sound, or completely transform it. 1 Use the [DSP ON/OFF] button to turn the DSP function on. The indicator lights when DSP is on. To turn DSP off, press the [DSP ON/OFF] button again. 3 Use the dial to select a DSP type.
Play with a Variety of Effects Panel Sustain This function adds sustain to the keyboard voices. Use it when you want to add sustain to the voices at all times, regardless of footswitch operation. The sustain function does not affect split voice. 1 Press the [FUNCTION] button to call up the FUNCTION display. 3 You can then use the [+] and [-] buttons to turn panel sustain on or off. NOTE • The sustain of some voices may not be markedly affected when the panel sustain function is turned on.
e erenc ef R Handy Performance Features Tap Start You can start the song/style by simply tapping the [TEMPO/TAP] button at the required tempo—4 times for time signatures in 4, and three times for time signatures in 3. You can change the tempo during song playback by pressing the button just twice. Touch Response Sensitivity You can adjust the keyboard’s sensitivity to dynamics in three steps. 1 Press the [FUNCTION] button. The currently selected function will appear in the display.
Handy Performance Features One Touch Setting Sometimes selecting the ideal voice to play with a song or style can be confusing. The One Touch Setting feature automatically selects a well-balanced voice for you when you select a style or song. Simply select voice number “000” to activate this feature. 1 Select voice number “000” (steps 1 to 2 on page 19). 4 Use the dial to change songs, then play the keyboard and listen to the voice. You should hear a different keyboard voice than you played in step 3.
Handy Performance Features Select an EQ Setting for the Best Sound Five different master equalizer (EQ) settings are provided to give you the best possible sound when listening through different reproduction systems—the instrument’s internal speakers, headphones, or an external speaker system. 1 Press the [FUNCTION] button. The currently selected function will appear in the display.
Handy Performance Features Pitch Controls ◆ Large Pitch Changes (Transpose) The overall pitch of the instrument can by shifted up or down by a maximum of 1 octave in semitone increments. ◆ Small Pitch Changes (Tuning) The overall tuning of the instrument can by shifted up or down by a maximum of 100 cents in 1-cent increments (100 cents = 1 semitone). 1 Press the [FUNCTION] button. 1 Press the [FUNCTION] button.
e erenc ef R Style (Auto-accompaniment) Functions Basic operation of the Style (auto-accompaniment) feature is described on page 27 of the Quick Guide. Here are some other ways you can play the styles, the style volume adjustment procedure, how you can play chords using the styles, and more. Pattern Variation (Sections) The DGX-630/YPG-635 features a wide variety of style “sections” that allow you to vary the arrangement of the accompaniment to match the song you are playing.
Style (Auto-accompaniment) Functions 1 Press the [STYLE] button and then select a style. 4 Press the [MAIN/AUTO FILL] button. 2 Press the [ACMP ON/OFF] button to turn auto accompaniment on. The name of the selected section—MAIN A or MAIN B—will be displayed. 5 Press the [INTRO/ENDING/rit.] button. Appears when auto accompaniment is on. You’re now ready to play the intro. 6 As soon as you play a chord with your 3 Press the [SYNC START] button to turn synchro start on.
Style (Auto-accompaniment) Functions 7 Press the [MAIN/AUTO FILL] button. When the fill-in is finished, it leads smoothly into the selected main section A/B. 8 Press the [INTRO/ENDING/rit.] button. The style will play while you are playing the keys Style playback will stop when you release the keys This switches to the ending section. When the ending is finished, the auto accompaniment stops automatically. You can have the ending gradually slow down (ritardando) by pressing the [INTRO/ENDING/rit.
Style (Auto-accompaniment) Functions Setting the Split Point The initial default split point is key number 54 (the F#2 key), but you can change it to another key using the procedure described below. 1 Press the [FUNCTION] button. 3 Use the dial to set the split point to any key from 021(A-1) through 108 (C7). Split point (54: F#2) Main voice Split voice NOTE 2 Use the CATEGORY [ • When you change the split point the auto-accompaniment split point also changes.
Style (Auto-accompaniment) Functions Play a Style with Chords but No Rhythm (Stop Accompaniment) When auto accompaniment is on (the ACMP ON icon is showing) and Synchro Start is off, you can play chords in the left-hand accompaniment range of the keyboard while the style is stopped and still hear the accompaniment chords. This is “Stop Accompaniment”, and any of the chord fingerings recognized by the instrument can be used (page 32).
Style (Auto-accompaniment) Functions Chord Basics Two or more notes played together constitute a “chord”. The most basic chord type is the “triad” consisting of three notes: the root, third, and fifth degrees of the corresponding scale. A C major triad, for example, is made up of the notes C (the root), E (the third note of the C major scale), and G (the fifth note of the C major scale).
Style (Auto-accompaniment) Functions ■Recognized Standard Chords ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● All chords in the chart are “C-root” chords.
Style (Auto-accompaniment) Functions Playing Styles Using the Entire Keyboard In “Play Along with a Style” on page 28 we described a method of playing styles in which chords were detected only to the left of the keyboard split point. By making the settings described below, however, chord detection for style accompaniment occurs over the entire range of the keyboard, allowing for even more dynamic style performance. In this mode only chords played in the normal way (page 32) can be detected.
Style (Auto-accompaniment) Functions Looking Up Chords Using the Chord Dictionary The Dictionary function is essentially a built-in “chord book” that shows you the individual notes of chords. It is ideal when you know the name of a certain chord and want to quickly learn how to play it. 1 Press and hold the LESSON [START] button for longer than a second. Hold for longer than a second 3 Press the “M7” (major seventh) key in the section of the keyboard labeled “CHORD TYPE”. (The note doesn’t sound.
e erenc ef R Song Settings Song Volume 1 Press the [FUNCTION] button. Song volume item Can be set between 000 and 127 2 Use the CATEGORY [ f r ] and [ ] buttons to select the Song Volume item. 3 Use the dial to set the song volume between 000 and 127. NOTE • Song volume can be adjusted while a song is selected. A-B Repeat You can specify a section of a song—“A” is the start point and “B” is the end point—for repeat playback.
Song Settings Muting Independent Song Parts Each “track” of a song plays a different part of the song—melody, percussion, accompaniment, etc. You can mute individual tracks and play the muted part on the keyboard yourself, or simply mute tracks other than the ones you want to listen to. To mute a track, press the appropriate track button (TRACK [1]–[5], [A]) button. Press the same button a second time to disengage track muting. No track number ... no data. Track number without border ...
e erenc ef R Memorize Your Favorite Panel Settings This instrument has a Registration Memory feature that lets you save your favorite settings for easy recall whenever they’re needed. Up to 16 complete setups can be saved (8 banks of two setups each). 8 Banks Memory 1 Memory 2 Up to 16 presets (eight banks of two each) can be memorized. Saving to the Registration Memory 1 Set the panel controls as required— select a voice, accompaniment style, etc. 2 Press the [MEMORY/BANK] button.
Memorize Your Favorite Panel Settings Recalling a Registration Memory 1 Press the [MEMORY/BANK] button. A bank number will appear in the display when you release the button. ● Settings That Can be Saved to the Registration Memory • Style settings* Style number, Auto Accompaniment ON/OFF, Split Point, Style settings (Main A/B), Style Volume, Tempo, Chord Fingering Bank number 2 Use the dial or the [1]–[8] number buttons to select bank you want to recall.
e erenc ef R The Functions The “Functions” provide access to a range of detailed instrument parameters for tuning, setting the split point, and adjusting the voices and effects. Take a look at the function list starting on the opposite page. There are 50 function parameters in all. When you locate a function you want to set up, simply select the function’s display name and adjust as required. Selecting and Setting Functions 1 Find the function you want to set in the list that begins on page 93.
The Functions ● Function Setting List Category Function Item Range/Settings Description Style Volume 000–127 Determines the volume of the Style. Song Volume 000–127 Determines the volume of the Song. Transpose -12–+12 Determines the pitch of the instrument by semitone increments. Tuning -100–+100 Sets the pitch of the instrument’s sound in 1-cent increments. Pitch Bend Range 01–12 Sets the pitch bend range in semitone increments.
The Functions Category Function Item Range/Settings Description Reverb Type 01–30 Determines the Reverb type, including off. (See the list on page 138) Chorus Type 1–25 Determines the Chorus type, including off. (See the list on page 138) DSP Type 001–183 Determines the DSP type, including off. (See the list on page 139) Sustain ON/OFF Determines whether or not panel sustain is always applied to the MAIN/ DUAL voices. Panel sustain is applied continuously when ON, or not applied when OFF.
The Functions Category LESSON UTILITY LANGUAGE Function Item Range/Settings Description Right-Part GuideTrack 1–16 Determines the guide track number for your right hand lesson. The setting is effective for songs in SMF format 0 and 1 transferred from a computer. Left-Part GuideTrack 1–16 Determines the guide track number for your left hand lesson. The setting is effective for songs in SMF format 0 and 1 transferred from a computer.
e erenc ef R Saving and Loading Data USB flash memory is a memory medium used for storing data. When a USB flash memory is inserted in this instrument’s USB TO DEVICE terminal, registered settings can be saved from or loaded into the instrument. USB flash memory can also be used to transfer Song, Style, and Music Database files to the instrument, where they can be selected and used in the same way as the internal data.
Saving and Loading Data ■ Precautions when using the USB TO DEVICE terminal This instrument features a built-in USB TO DEVICE terminal. When connecting a USB device to the terminal, be sure to handle the USB device with care. Follow the important precautions below. NOTE • Although CD-R/RW drives can be used to read data to the instrument, they cannot be used for saving data.
Saving and Loading Data Formatting USB Flash Memory New USB flash memory must be formatted before they can be used by this instrument. 5 Press the [EXECUTE] button again, or CAUTION • If you format a USB flash memory that already contains data, all of the data will be erased. Be careful not to erase important data when using the format function. the [+] button, and the format operation will begin.
Saving and Loading Data Saving User Files (Registration Memory) to USB Flash Memory This operation saves a “User File” containing the registration memory data to a USB flash memory device. The User File name will have a “.usr” extension which will not appear in the instrument’s display. 1 Make sure that a properly formatted USB flash memory has been properly connected to the instrument’s USB TO DEVICE terminal, and that the icon is showing in the MAIN display.
Saving and Loading Data Save a User Song to USB Flash Memory This operation saves a user song (song numbers 031–035) to USB flash memory. 1 Make sure that a properly formatted USB flash memory has been properly connected to the instrument’s USB TO DEVICE terminal, and that the icon is showing in the MAIN display. 7 Change the file name as necessary. Refer to “Saving User Files (Registration Memory) to USB Flash Memory” on page 99 for filename entry. 2 Press the FILE CONTROL [MENU] button.
Saving and Loading Data Loading Files from a USB Flash Memory User files as well as Style, Song, and Music Database files residing on a USB flash memory can be loaded into the instrument. 4 Use the dial to select the file you want CAUTION • If you load a User File registration memory data will be overwritten by the newly loaded data. Save important data to a USB flash memory before loading data that will overwrite it.
Saving and Loading Data Deleting Data from a USB Flash Memory This procedure deletes User, Style, Song, and Music Database files from a USB flash memory. 1 Make sure that the USB flash memory containing the file(s) you want to delete has been properly connected to the instrument’s USB TO DEVICE terminal, and that the icon is showing in the MAIN display. 4 Use the dial to select the file you want to delete.
Saving and Loading Data Delete User Data from the Instrument This procedure deletes the User Song as well as Style, Song, and Music Database files transferred from an external device such as a computer. This operation does not erase the preset data. r f 1 Press the FILE CONTROL [MENU] button. 2 Use the CATEGORY [ ] and [ ] buttons to locate the User Delete item. Only “User Delete” can be selected if no USB flash memory is connected to the instrument.
e erenc ef R Connections Connectors q q USB TO DEVICE terminal This terminal allows connection to USB storage devices. Refer to “Precautions when using the USB TO DEVICE terminal” on page 97. 104 DGX-630/YPG-635 Owner’s Manual w w USB TO HOST terminal This terminal allows direct connection to a personal computer. Refer to “Connecting a Personal Computer” on page 105 for more information.
Connections Connecting a Personal Computer The following functions become available when this instrument is connected to a computer. ● Performance data can be transferred between the instrument and the computer (page 106). ● Files can be transferred between the instrument and the computer (page 108). The connection procedure is as follows: 1 Install the USB-MIDI driver on your com- puter. The USB-MIDI driver is included on the CD-ROM. Installation of the USB-MIDI driver is described on pages 114–115.
Connections Transferring Performance Data to and from a Computer By connecting the instrument to a computer, the instrument’s performance data can be used on the computer, and performance data from the computer can be played on the instrument. ● When the instrument is connected with computer, it transmits/receives performance data.
Connections ■PC Mode ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● A number of MIDI settings need to be made when you want to transfer performance data between the computer and the instrument. The PC Mode item can conveniently make multiple settings for you in one operation. Three settings are available: PC1, PC2, and OFF. This setting is not necessary when transferring song or backup files between the computer and the instrument.
Connections Initial Send This function lets you send the panel setup data to a computer. Before you record performance data to a sequencer application running on your computer, it is a good idea to first send and record the panel setup data before the actual performance data. 1 Press the [FUNCTION] button. 2 Use the CATEGORY [ 3 Press [+/YES] to send, or press [-/NO] to cancel. r f ] and [ ] buttons to select the Initial Send item.
Connections ■Use Musicsoft Downloader To Transfer Songs From the Accessory CD-ROM To the Instrument’s flash memory ● ● ● ● ● NOTE • If a song or style is being played, stop playback before proceeding. 1 Install the Musicsoft Downloader and USB-MIDI driver to your computer, then connect the computer and the instrument (page 113). At this point you can select a Style or Music Database file on the computer or CD-ROM and transfer it to the instrument in the same way as a song file.
Connections 8 Close the window to end the Musicsoft Downloader. NOTE • End the Musicsoft Downloader to playback the file transferred from your computer. 9 To playback a song stored in flash memory, press the [SONG] button. Use the dial to select the song you want to play, then press the [START/STOP] button to start playback. CAUTION • Do not unplug the USB cable during a data transfer.
e erenc ef R Accessory CD-ROM Installation Guide SPECIAL NOTICES • The software and this manual are the exclusive copyrights of Yamaha Corporation. • Use of the software and this manual is governed by the license agreement which the purchaser fully agrees to upon breaking the seal of the software packaging. (Please read carefully the Software Licensing Agreement at the end of this manual before installing the application.
Accessory CD-ROM Installation Guide CD-ROM Contents e r Folder Name w Application / Data Name Contents Musicsoft Downloader This application can be used to download MIDI song data from the Internet and transfer it from the computer to the instrument’s memory. DMN_ Digital Music Notebook Digital Music Notebook is a combination music learning program and online service that makes it easy and fun to practice and master your favorite songs.
Accessory CD-ROM Installation Guide System Requirements Application/Data Musicsoft Downloader OS Windows 2000/XP Home Edition/XP Professional/ Vista * Only 32-bit is supported.
Accessory CD-ROM Installation Guide Installing the driver on Windows 2000 Installing the driver on Windows XP 1 Start the computer and use the “Adminis- 1 Start the computer and use the “Adminis- 2 3 4 5 6 trator” account to log on to Windows 2000. Select [My Computer] ➔ [Control Panel] ➔ [System] ➔ [Hardware] ➔ [Driver Signing] ➔ [File Signature Verification], and check the radio button to the left of “Ignore—Install all files, regardless of file signature” and click [OK].
Accessory CD-ROM Installation Guide (Some computers may take a while to display the window.) NOTE • This Wizard window will not appear when using Windows XP Professional x64 Edition. There is no need to restart the computer. The USB-MIDI driver installation is complete. 10 When using Windows XP Professional x64 Edition, the Support Module must be installed. After installing the USB-MIDI drivers for all the connected USB devices, select “My Computer” from the Start menu.
Accessory CD-ROM Installation Guide ■Troubleshooting The driver cannot be installed. • Is the USB cable connected correctly? Check the USB cable connection. Disconnect the USB cable, then connect it again. • Is the USB function enabled on your computer? When you connect the instrument to the computer for the first time, if the “Add New Hardware Wizard” does not appear, the USB function on the computer may be disabled. Perform the following steps.
Accessory CD-ROM Installation Guide How can I remove the driver? [Windows 2000/XP/Vista] 1 Start the computer and use the “Administrator” account to log on Windows. Close all applications and windows that are open. 2 Insert the included CD-ROM into the CDROM drive. 3 Select “My Computer” from the Start menu. 4 Right-click the CD-ROM icon and select “Open” from the pop-up menu. 5 Select “USBdrvVista_” or “USBdrv2k_” folder ➔ “uninstall” folder ➔ “uninstall.exe” file and launch “uninstall.exe.
Appendix Troubleshooting ■ For the Instrument Problem Possible Cause and Solution When the instrument is turned on or off, a popping sound is temporarily produced. This is normal and indicates that the instrument is receiving electrical power. When using a mobile phone, noise is produced. Using a mobile phone in close proximity to the instrument may produce interference. To prevent this, turn off the mobile phone or use it further away from the instrument.
Troubleshooting Problem Possible Cause and Solution The appropriate display does not appear when the [SONG], [EASY SONG ARRANGER], [STYLE], or [VOICE] button is pressed. Is another display showing? Try pressing the [EXIT] button to return to the MAIN display, and then pressing one of the mentioned buttons. The wrong notes sound when the keyboard is played. Perhaps the performance assistant technology is turned on. Press the [PERFORMANCE ASSISTANT] button to turn it off.
Messages LCD Message Comment Access error! Indicates the failure in reading or writing from/to the media or the flash memory. All Memory Clearing... Displayed while erasing all data in the flash memory. Never turn the power off during data transmission. Are you sure? Confirms whether Song Clear or Track Clear is executed or not. Backup Clearing... Displayed while clearing the back-up data in the flash memory. Cancel Displayed when the transmission of Initial Send is cancelled.
Messages LCD Message Comment OverCurrent Communication with the USB device has been shut down because of the overcurrent to the USB device. Disconnect the device from the USB TO DEVICE terminal, then turn on the power of the instrument. Overwrite ? Confirms whether overwriting is executed or not. Please Wait... Displayed when executing the jobs that take some time, such as displaying scores and lyrics, or stopping recording.
Scores This demo is an example of how the Easy Song Arranger can be used to change styles throughout a piece. Song No.
Scores DGX-630/YPG-635 Owner’s Manual 123
Scores This score is provided with the intent that the pitch will be corrected by the performance assistant technology feature. If you play the “Play These Notes” part using the performance assistant technology feature, the part will be corrected and played so that it matches the backing part. Song No. 10 q =61 (Function Demo for performance assistant technology) Ave Maria P.A.T. Type =CHORD Your Turn. Repeatedly Play the Same Key.
Scores DGX-630/YPG-635 Owner’s Manual 125
Scores This score is provided with the intent that the pitch will be corrected by the performance assistant technology feature. If you play the “Play These Notes” part using the performance assistant technology feature, the part will be corrected and played so that it matches the backing part. Song No. 11 q =108 (Function Demo for performance assistant technology) Nocturne op.9-2 P.A.T.
Scores DGX-630/YPG-635 Owner’s Manual 127
Voice List ■ Maximum Polyphony ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● The instrument has 64-note maximum polyphony. This means that it can play a maximum of up to 64 notes at once, regardless of what functions are used. Auto accompaniment uses a number of the available notes, so when auto accompaniment is used the total number of available notes for playing on the keyboard is correspondingly reduced. The same applies to the Split Voice and Song functions.
Voice List Voice No.
Voice List Voice No.
Voice List Voice No.
Drum Kit List • “ ” indicates that the drum sound is the same as “Standard Kit 1”. • Each percussion voice uses one note. • The MIDI Note # and Note are actually one octave lower than keyboard Note # and Note. For example, in “131: Standard Kit 1”, the “Seq Click H” (Note# 36/Note C1) corresponds to (Note# 24/Note C0). • Key Off: Keys marked “O” stop sounding the instant they are released. • Voices with the same Alternate Note Number (*1 ... 4) cannot be played simultaneously.
Drum Kit List Voice No.
Style List Style No.
Music Database List MDB No.
Songs Provided On the Supplied CD-ROM File Name 001Nutcr.mid 002Orphe.mid 003Slavo.mid 004Prima.mid 005Medit.mid 006Guill.mid 007Fruhl.mid 008Ungar.mid 009Fruhl.mid 010Dolly.mid 011Cande.mid 012Arabe.mid 013Pasto.mid 014Petit.mid 015Innoc.mid 016Progr.mid 017Taren.mid 018Cheva.mid 019Etude.mid 020Marci.mid 021Turki.mid 022Valse.mid 023Menue.mid 024Momen.mid 025Enter.mid 026Prelu.mid 027Violl.mid 028Angel.mid 029Saraf.mid 030Ameri.mid 031Brown.mid 032Lomon.mid 033Bonni.mid 034Londo.mid 035Banjo.mid 036Vogle.
Harmony Type List No.
Effect Type List ● Reverb Types No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Type HALL1 HALL2 HALL3 HALL4 HALL5 HALL M HALL L ROOM1 ROOM2 ROOM3 ROOM4 ROOM5 ROOM6 ROOM7 ROOM S ROOM M ROOM L STAGE1 STAGE2 STAGE3 STAGE4 PLATE1 PLATE2 PLATE3 GM PLATE WHITE ROOM TUNNEL CANYON BASEMENT NO EFFECT Description Reverb simulating the acoustics of a hall. Reverb simulating the acoustics of a room. Reverb suitable for a solo instrument. Reverb simulating a plate reverb unit.
Effect Type List ● DSP Types No.
Effect Type List No. Type 60 SYMPHONIC1 61 SYMPHONIC2 62 ENS DETUNE (Ensemble Detune) Description Adds more stages to the modulation of Celeste. Chorus effect without modulation, created by adding a slightly pitchshifted sound.
Effect Type List No. 99 Type OD+DELAY1 (Overdrive + Delay1) 100 OD+DELAY2 (Overdrive + Delay2) 101 CMP+DST+DLY1 (Compressor + Distortion + Delay1) 102 CMP+DST+DLY2 (Compressor + Distortion + Delay2) 103 CMP+OD+DLY1 (Compressor + Overdrive + Delay1) Description MSB LSB 95 17 95 1 96 16 96 0 96 17 96 1 Overdrive and Delay are connected in series. Compressor, Distortion and Delay are connected in series. Compressor, Overdrive and Delay are connected in series.
Effect Type List No. Type 134 EP TC WAH (EP Touch Wah) 135 WH+DST+DLY1 (Wah + Distortion + Delay1) 136 WH+DST+DLY2 (Wah + Distortion + Delay2) 137 WH+DST+TDLY (Wah + Distortion + Tempo Delay) 138 WH+OD+DLY1 (Wah + Overdrive + Delay1) 139 WH+OD+DLY2 (Wah + Overdrive + Delay2) 140 WH+OD+TDLY1 (Wah + Overdrive + Tempo Delay1) Description EP Touch Wah MSB LSB 82 19 97 16 97 0 102 0 97 17 97 1 102 1 102 16 Wah, Distortion and Delay are connected in series.
Effect Type List / Effekttypliste / Liste des types d’effets / Lista de tipos de efectos No. Type Description MSB LSB 76 16 171 EQ DISCO Equalizer effect that boosts both high and low frequencies, as is typical in most disco music. 172 EQ TEL Equalizer effect that cuts both high and low frequencies, to simulate the sound heard through a telephone receiver. 76 17 173 2BAND EQ Stereo EQ which emphasizes low and high frequencies.
DGX-630/YPG-635 Owner’s Manual Change Control 0,32 1,11,84 6,38 7,10 64,66,67 71 72 73 74 91,93,94 96-97 100-101 Key's Ch's After Touch Pitch Bend Note ON Note OFF Velocity o x o o o x o x x o x o o 0-24 semi x x o 9nH,v=1-127 x 9nH,v=0 *1 *1 *1 *1 *1 0 - 127 : True voice ************** 3 x ************** Default Messages Altered Mode Note Number 1 - 16 x Default Changed Basic Channel Function...
: True # x x x x o x Aux o(120,126,127) o(121) o(122) o(123-125) o x o o x x x o o 0 - 127 *1 Refer to #2 on page 146. Mode 1 : OMNI ON , POLY Mode 2 : OMNI ON ,MONO Mode 3 : OMNI OFF, POLY Mode 4 : OMNI OFF,MONO :All Sound OFF :Reset All Cntrls :Local ON/OFF :All Notes OFF Mes- :Active Sense sages:Reset o o x x x o o 0 - 127 ************** System : Clock Real Time: Commands Common : Song Pos. : Song Sel.
MIDI Data Format NOTE: 1 By default (factory settings) the instrument ordinarily functions as a 16-channel multi-timbral tone generator, and incoming data does not affect the panel voices or panel settings. However, the MIDI messages listed below do affect the panel voices, auto accompaniment, and songs. • MIDI Master Tuning • System exclusive messages for changing the Reverb Type, Chorus Type and DSP Type. 2 Messages for these control change numbers cannot be transmitted from the instrument itself.
ATTENTION SOFTWARE LICENSE AGREEMENT PLEASE READ THIS SOFTWARE LICENSE AGREEMENT (“AGREEMENT”) CAREFULLY BEFORE USING THIS SOFTWARE. YOU ARE ONLY PERMITTED TO USE THIS SOFTWARE PURSUANT TO THE TERMS AND CONDITIONS OF THIS AGREEMENT. THIS AGREEMENT IS BETWEEN YOU (AS AN INDIVIDUAL OR LEGAL ENTITY) AND YAMAHA CORPORATION (“YAMAHA”). BY BREAKING THE SEAL OF THIS PACKAGE YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE.
SIBELIUS SCORCH LICENSE AGREEMENT By installing and/or using this Product you (an individual or legal entity) agree with the Licensor to be bound by the terms of this License which will govern your use of the Product. If you do not accept these terms, do not install or use this Product. The Product is copyright © 1987-2007 Sibelius Software, a division of Avid Technology, Inc, and its licensors. 1.
Specifications Keyboards Song • 88 Graded Hammer Standard keys (A-1–C7), with Touch Response. Display • 320 x 240 dots LCD display (backlit) Setup • STANDBY/ON • MASTER VOLUME: MIN–MAX • LCD CONTRAST Panel Controls • SONG, VOICE, STYLE, EASY SONG ARRANGER, P.A.T.
Index Panel controls and terminals 150 r f +/– .................................................. 16, 67 ........................................................ 68 0–9 .................................................. 16, 67 A-B REPEAT ................................. 16, 88 ACMP ON/OFF ............................. 16, 28 CATEGORY [ ] and [ ] ........... 16, 67 DC IN 12V ..................................... 13, 17 DEMO ............................................ 16, 35 Dial .......................
Index Measure ................................................ 69 Melody ........................................... 37, 49 Melody Score ....................................... 37 Melody type (performance assistant technology) .................. 39, 44 Melody Voice ................................. 59, 89 Messages ............................................ 120 Metronome ........................................... 24 MIDI ................................................... 106 MIDI Data Format ...........
Limited Warranty 90 DAYS LABOR 1 YEAR PARTS Yamaha Corporation of America, hereafter referred to as Yamaha, warrants to the original consumer of a product included in the categories listed below, that the product will be free of defects in materials and/or workmanship for the periods indicated.
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. NORTH AMERICA CANADA Yamaha Canada Music Ltd.
Yamaha Global Home http://www.yamaha.com/ Yamaha Manual Library http://www.yamaha.co.jp/manual/ U.R.G., Digital Musical Instruments Division © 2007 - 2011 Yamaha Corporation WM92600 103PO***.