DSP-AX563_B-cv.
01EN_DSP-AX563_B.book Page i Friday, February 1, 2008 11:08 AM CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. Caution: Read this before operating your unit. 1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 Install this sound system in a well ventilated, cool, dry, clean place – away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold.
01EN_DSP-AX563_B.book Page 1 Friday, February 1, 2008 11:08 AM Contents Features ................................................................... 2 Getting started ........................................................ 3 Quick start guide .................................................... 4 PREPARATION Connections ............................................................. 9 Using AUTO SETUP .............................................. 24 ADVANCED OPERATION SET MENU .........................
01EN_DSP-AX563_B.book Page 2 Friday, February 1, 2008 11:08 AM Features Features Built-in 7-channel power amplifier DOCK terminal ◆ Minimum RMS output power 1 kHz, 0.9% THD, 6 Ω 90 W/ch ◆ DOCK terminal to connect a Yamaha iPod universal dock (such as YDS-10, sold separately) or Bluetooth adapter (such as YBA-10, sold separately).
01EN_DSP-AX563_B.book Page 3 Friday, February 1, 2008 11:08 AM Getting started Getting started ■ Installing batteries in the remote control Check that you received all of the following parts. ❏ Remote control ❏ Batteries (2) (AAA, R03, UM-4) ❏ Optimizer microphone 1 3 INTRODUCTION ■ Supplied accessories 2 1 Take off the battery compartment cover. 2 Insert the two supplied batteries (AAA, R03, UM-4) according to the polarity markings (+ and –) on the inside of the battery compartment.
01EN_DSP-AX563_B.book Page 4 Friday, February 1, 2008 11:08 AM Quick start guide Quick start guide The following steps describe the easiest way to enjoy DVD movie playback in your home theater. Video monitor Front right speaker Front left speaker Prepare the following items. Subwoofer Surround right speaker Center speaker Surround back right speaker DVD player Surround back left speaker Surround left speaker ❏ Speakers ❏ Front speaker .....................................x 2 ❏ Center speaker ........
01EN_DSP-AX563_B.book Page 5 Friday, February 1, 2008 11:08 AM Quick start guide Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. Step 1: Set up your speakers Front and center speakers Loosen Insert INTRODUCTION Place your speakers in the room and connect them to this unit.
01EN_DSP-AX563_B.book Page 6 Friday, February 1, 2008 11:08 AM Quick start guide Step 2: Connect your DVD player and other components 3 SPEAKERS COAXIAL DTV/CBL IN2 1 OUT HDMI DVD DTV/CBL DTV/CBL PB AV amplifier MD/CD-R CD CD DIGITAL 2 3 OUTPUT DIGITAL INPUT COMPONENT VIDEO PR Video monitor 4 OPTICAL OPTICAL DVD DVD IN1 Connect the video cable to the video input jack of your video monitor and the VIDEO MONITOR OUT jack of this unit.
01EN_DSP-AX563_B.book Page 7 Friday, February 1, 2008 11:08 AM Quick start guide Step 3: Press SCENE 1 button Turn on the video monitor and then set the input source selector of the video monitor to this unit. 2 Press B SCENE 1. This unit is turned on. “DVD Viewing” appears in the front panel display, and this unit automatically optimize own status for the DVD playback.
01EN_DSP-AX563_B.book Page 8 Friday, February 1, 2008 11:08 AM Quick start guide ■ After using this unit... Press A STANDBY/ON on the front panel to set this unit to the standby mode. What do you want to do with this unit? ■ Customizing the SCENE templates • Using various SCENE templates ☞ P. 28 • Creating your original SCENE templates ☞ P. 31 ■ Using various input sources • Basic controls of this unit ☞ P. 33 • Using your USB portable device with this unit ☞ P.
01EN_DSP-AX563_B.
01EN_DSP-AX563_B.book Page 10 Friday, February 1, 2008 11:08 AM Connections Placing speakers The speaker layout below shows the speaker setting we recommend. You can use it to enjoy CINEMA DSP and multi-channel audio sources. C FR FL FR SW FL 30˚ SR C SL SR SL 60˚ SL 80˚ SBL SBR SR SBR SBL 30 cm (12 in) or more Front left and right speakers (FL and FR) The front speakers are used for the main source sound plus effect sounds.
01EN_DSP-AX563_B.book Page 11 Friday, February 1, 2008 11:08 AM Connections Connecting speakers Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty, this unit cannot reproduce the input sources accurately. When you use single surround back speaker, connect the speaker to the left SURROUND BACK terminal (SINGLE).
01EN_DSP-AX563_B.book Page 12 Friday, February 1, 2008 11:08 AM Connections ■ Before connecting to the SPEAKERS terminal A speaker cord is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a stripe, groove or ridges. Connect the striped (grooved, etc.) cable to the “+” (red) terminals of this unit and your speaker. Connect the plain cable to the “–” (black) terminals.
01EN_DSP-AX563_B.book Page 13 Friday, February 1, 2008 11:08 AM Connections Information on jacks and cable plugs Connect one of the type of the audio jack(s) and/or video jack(s) that your input components are equipped with.
01EN_DSP-AX563_B.book Page 14 Friday, February 1, 2008 11:08 AM Connections Information on HDMI™ ■ HDMI compatibility with this unit Audio signal types Audio signal formats Compatible HDMI components 2ch Linear PCM 2ch, 32-192 kHz, 16/20/24 bit CD, DVD-Video, DVD-Audio, etc. Multi-ch Linear PCM 8ch, 32-192 kHz, 16/20/24 bit DVD-Audio, etc. Bitstream Dolby Digital, DTS DVD-Video, etc. This unit’s HDMI interface is based on the following standards: • HDMI Version 1.
01EN_DSP-AX563_B.
01EN_DSP-AX563_B.book Page 16 Friday, February 1, 2008 11:08 AM Connections Connecting video components Connect your TV (or projector) to the HDMI OUT jack, the COMPONENT VIDEO MONITOR OUT jacks, the S VIDEO MONITOR OUT jack or the VIDEO MONITOR OUT jack of this unit. Notes • Some video monitors connected to this unit via a DVI connection fail to recognize the HDMI audio/video signals being input if they are in the standby mode. In this case, the HDMI indicator flashes irregularly.
01EN_DSP-AX563_B.book Page 17 Friday, February 1, 2008 11:08 AM Connections Connecting other components Make sure that this unit and other components are unplugged from the AC wall outlets. Notes • When “VIDEO CONV.” is set to “OFF” (see page 59), be sure to make the same type of video connections as those made for your TV (see page 16). For example, if you connected your TV to the VIDEO MONITOR OUT jack of this unit, connect your other components to the VIDEO jacks.
01EN_DSP-AX563_B.
01EN_DSP-AX563_B.book Page 19 Friday, February 1, 2008 11:08 AM Connections Connecting audio components Connect the audio components as follows. Make sure that this unit and other components are unplugged from the AC wall outlets. ■ Connecting a CD player, a CD recorder/MD recorder, and a tuner Note • When you connect your CD player via analog and digital connection, priority is given to the signal input at the DIGITAL INPUT jack.
01EN_DSP-AX563_B.book Page 20 Friday, February 1, 2008 11:08 AM Connections Connecting a Yamaha iPod™ universal dock or Bluetooth™ adapter Make sure that this unit and other components are unplugged from the AC wall outlets. Using REMOTE OUT jack When the components are the Yamaha products and have the capability of the transmission of the remote control signals, connect the REMOTE OUT jack to the remote control input jack with the monaural analog mini cable as follows.
01EN_DSP-AX563_B.book Page 21 Friday, February 1, 2008 11:08 AM Connections Using the VIDEO AUX jacks on the front panel Use the VIDEO AUX jacks on the front panel to connect a game console or a video camera to this unit. Connecting the power cable Once all connections are complete, plug the power cable into the AC wall outlet. Caution Be sure to turn down the volume of this unit and other components before making connections.
01EN_DSP-AX563_B.book Page 22 Friday, February 1, 2008 11:08 AM Connections Front panel display 1 2 DVR MULTI CH USB 3 V-AUX DOCK q EX q DIGITAL PLUS SP AB 96 ES 24 q PL x MATRIX DISCRETE 4 DTV/CBL DVD 5 MD/CD-R ENHANCER SILENT CINEMA 7 TUNER VOL.
01EN_DSP-AX563_B.book Page 23 Friday, February 1, 2008 11:08 AM Connections B CINEMA DSP indicator Lights up when you select a sound field program (see page 39). ■ Using the remote control The remote control transmits a directional infrared ray. Be sure to aim the remote control directly at the remote control sensor on this unit during operation. VIRTUAL indicator Lights up when Virtual CINEMA DSP is active (see page 39).
01EN_DSP-AX563_B.book Page 24 Friday, February 1, 2008 11:08 AM Optimizing the speaker setting for your listening room Optimizing the speaker setting for your listening room This unit employs the YPAO (Yamaha Parametric Room Acoustic Optimizer) technology which lets you avoid troublesome listening-based speaker setup and achieves highly accurate sound adjustments automatically.
01EN_DSP-AX563_B.book Page 25 Friday, February 1, 2008 11:08 AM Optimizing the speaker setting for your listening room 4 Make sure that “SETUP” is set to “AUTO” and the pointer is pointing at “START”. y You can also select the following setup methods. In this case, press 7 k to select “SETUP”, press 7 l / h to select the one of the following choises and then select “START”. Note “RELOAD” or “UNDO” is available only when you have previously run “AUTO SETUP” and confirmed the results.
01EN_DSP-AX563_B.book Page 26 Friday, February 1, 2008 11:08 AM Optimizing the speaker setting for your listening room The display changes as follows. 7 Press 8 k and 8 ENTER to display the setup results in detail. 8 Press 8 l / h repeatedly to toggle between the setup result displays. AUTO SETUP SETUP;;;;;;;AUTO .
01EN_DSP-AX563_B.book Page 27 Friday, February 1, 2008 11:08 AM Optimizing the speaker setting for your listening room 10 11 Press 7 n and then press 7 l / h to select “SET” or “CANCEL”. Choices: SET, CANCEL • Select “SET” to confirm the “AUTO SETUP” results. • Select “CANCEL” to cancel the “AUTO SETUP” results. Press 7 ENTER to confirm your selection. The top “SET MENU” display appears in the OSD.
01EN_DSP-AX563_B.book Page 28 Friday, February 1, 2008 11:08 AM SELECTING THE SCENE TEMPLATES Selecting the SCENE templates This unit is equipped with 16 preset SCENE templates for various situations of using this unit. As the initial factory setting, the following SCENE templates are assigned to each SCENE button: 2 Press J INPUT l / h (or press 4 AMP and then press 7l / h) to select the desired template.
01EN_DSP-AX563_B.
01EN_DSP-AX563_B.book Page 30 Friday, February 1, 2008 11:08 AM Selecting the SCENE templates ■ Preset SCENE templates descriptions The illustrations of the SCENE button in the following table indicate the assigned SCENE buttons in the default setting. SCENE template Input source Playback mode Features DVD Viewing DVD* STRAIGHT DVD Movie Viewing DVD* MOVIE Movie Dramatic Select this SCENE template when you play back movies on your DVD player.
01EN_DSP-AX563_B.book Page 31 Friday, February 1, 2008 11:08 AM Selecting the SCENE templates Creating your original SCENE templates 3 You can create your original SCENE templates for each SCENE button. You can refer to the preset 16 SCENE templates to create the original SCENE templates.
01EN_DSP-AX563_B.book Page 32 Friday, February 1, 2008 11:08 AM Selecting the SCENE templates Using remote control on the SCENE feature ■ Controlling the input source components in the SCENE mode ■ Setting input source of the customized SCENE template on the remote control You can operate both this unit and the input source component by using the remote control. You must set the appropriate remote control code for each input source in advance (see page 65).
01EN_DSP-AX563_B.book Page 33 Friday, February 1, 2008 11:08 AM PLAYBACK Playback Caution Extreme caution should be exercised when you play back CDs encoded in DTS. If you play back a CD encoded in DTS on a DTS-incompatible CD player, you will only hear some unwanted noise that may damage your speakers. Check whether your CD player supports CDs encoded in DTS. Also, check the sound output level of your CD player before you play back a CD encoded in DTS.
01EN_DSP-AX563_B.book Page 34 Friday, February 1, 2008 11:08 AM Playback Selecting audio input jacks (AUDIO SELECT) This unit comes with a variety of input jacks. Use this feature (audio input jack select) to switch between input jacks when more than one input jack is assigned to as the same input source. y • We recommend setting the audio input jack select to “AUTO” in most cases. • You can adjust the default audio input jack select of this unit by using “AUDIO SELECT” in “OPTION MENU” (see page 60).
01EN_DSP-AX563_B.book Page 35 Friday, February 1, 2008 11:08 AM Playback Displaying the current status of this unit on a video monitor You can display the operating information of this unit on a video monitor. 1 Turn on the video monitor connected to this unit. 2 Press M DISPLAY. The current status screen appears in the OSD. Using your headphones Connect a pair of headphones with a stereo analog audio cable plug to the PHONES jack on the front panel.
01EN_DSP-AX563_B.book Page 36 Friday, February 1, 2008 11:08 AM Playback Playing video sources in the background of an audio source You can combine a video image from a video source with sound from an audio source. For example, you can enjoy listening to classical music while viewing beautiful scenery from the video source on the video monitor. Press the input selector buttons (4) to select a video source and then an audio source. ■ Audio information Information Descriptions FORMAT Signal format.
01EN_DSP-AX563_B.book Page 37 Friday, February 1, 2008 11:08 AM Playback Using the sleep timer Use this feature to automatically set the main zone to the standby mode after a certain amount of time. Press 4 AMP and then press R SLEEP repeatedly to set the amount of time. Each time you press R SLEEP, the front panel display changes as shown below. SLEEP 120min SLEEP OFF SLEEP 30min SLEEP 90min SLEEP 60min The SLEEP indicator flashes while you are switching the amount of time for the sleep timer.
01EN_DSP-AX563_B.book Page 38 Friday, February 1, 2008 11:08 AM SOUND FIELD PROGRAMS Sound field programs This unit is equipped with a variety of precise digital decoders that allow you to enjoy multi-channel playback from almost any stereo or multi-channel sound source. Press G PROGRAM l / h (or press 4 AMP and then press A PROG l / h repeatedly). The name of the selected sound field program appears in the front panel display.
01EN_DSP-AX563_B.book Page 39 Friday, February 1, 2008 11:08 AM Sound field programs ■ Enjoying 2-channel sources using the standard decoders Signals input from 2-channel sources can also be played back on multi-channels. Press 4 AMP and then press OSUR. DECODE repeatedly to select a decoder. You can select from the following decoders depending on the type of source you are playing and your personal preference.
01EN_DSP-AX563_B.book Page 40 Friday, February 1, 2008 11:08 AM Sound field programs ■ Editing sound fields parameters y You can enjoy good quality sound with the factory default parameters. Although you do not have to change the initial settings, you can change some of the parameters to better suit the input source or your listening room. For Pop/Rock, Hall, Jazz, Game, TV Sports, Movie Spacious and Movie Dramatic: 1 While listening to a source, press 4 AMP and then press Q PARAMETER.
01EN_DSP-AX563_B.book Page 41 Friday, February 1, 2008 11:08 AM USING AUDIO FEATURES Using audio features Enjoying high quality sound Use the DIRECT mode to enjoy the high quality sounds of the selected source. When the DIRECT mode is activated, this unit plays back the selected source with the least circuitry. Adjusting the speaker level You can adjust the output level of each speaker while listening to a music source. This is also possible when playing sources input at the MULTI CH INPUT jacks.
01EN_DSP-AX563_B.book Page 42 Friday, February 1, 2008 11:08 AM Using audio features Selecting the night listening mode The night listening modes are designed to improve listenability at lower volumes or at night. 1 Press 4 AMP and then P NIGHT repeatedly to select “NIGHT:CINEMA” or “NIGHT:MUSIC”. Choices: NIGHT:CINEMA, NIGHT:MUSIC, OFF • Select “NIGHT:CINEMA” when watching films to reduce the dynamic range of film soundtracks and make dialog easier to hear at lower volumes.
01EN_DSP-AX563_B.book Page 43 Friday, February 1, 2008 11:08 AM USING A USB MEMORY DEVICE OR A USB PORTABLE AUDIO PLAYER Using a USB memory device or a USB portable audio player Use this feature to enjoy WAV (PCM format only), MP3 and WMA files saved on your USB memory device or USB portable audio player connected to the USB port on the front panel of this unit. ■ Supported USB devices This unit supports USB mass storage class devices (except USB hard disk drives) using FAT16 or FAT32 format.
01EN_DSP-AX563_B.book Page 44 Friday, February 1, 2008 11:08 AM Using a USB memory device or a USB portable audio player 3 4 Press 7 k / n / l / h on the remote control to select the desired file. • Press 7 k / n to select the desired file/folder. • Press 7 ENTER or 7 h to enter the selected folder. • Press 7 l to return to the previous folder level. ■ The function of the play information display USB Press 7 ENTER to play the selected file.
01EN_DSP-AX563_B.book Page 45 Friday, February 1, 2008 11:08 AM USING IPOD™ Using iPod™ Once you have stationed your iPod in a Yamaha iPod universal dock (such as YDS-10, sold separately) connected to the DOCK terminal of this unit (see page 20), you can enjoy playback of your iPod using the supplied remote control. You can also use the Compressed Music Enhancer mode of this unit to improve the sound quality of the compression artifacts (such as the MP3 format) stored on your iPod (see page 20).
01EN_DSP-AX563_B.book Page 46 Friday, February 1, 2008 11:08 AM Using iPod™ ■ Controlling iPod in the menu browse mode You can perform the advanced operations of your iPod using the supplied remote control when you connect this unit and a monitor using the S VIDEO or VIDEO connection. You can browse the songs stored on your iPod in the OSD. Further, you can change or adjust settings for your iPod to suit your personal preferences.
01EN_DSP-AX563_B.book Page 47 Friday, February 1, 2008 11:08 AM USING BLUETOOTH™ COMPONENTS Using Bluetooth™ components You can connect a Yamaha Bluetooth adapter (such as YBA-10, sold separately) to the DOCK terminal of this unit and enjoy the music contents stored in your Bluetooth component (such as a portable music player) without wiring between this unit and the Bluetooth component. You need to perform “pairing” the connected Bluetooth adapter and your Bluetooth component in advance.
01EN_DSP-AX563_B.book Page 48 Friday, February 1, 2008 11:08 AM RECORDING Recording Recording adjustments and other operations are performed from the recording components. Refer to the operating instructions for those components. Notes • When this unit is set to the standby mode, you cannot record between other components connected to this unit. • TONE CONTROL (see page 41) and VOLUME settings, speaker levels (see page 41) and the sound field programs (see page 38) do not affect recorded material.
01EN_DSP-AX563_B.book Page 49 Friday, February 1, 2008 11:08 AM SET MENU SET MENU You can use the following parameters in “SET MENU” to adjust a variety of system settings and customize the way this unit operates. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening environment. ■ Auto setup AUTO SETUP Use this feature to automatically adjust speaker and system parameters (see page 24).
01EN_DSP-AX563_B.book Page 50 Friday, February 1, 2008 11:08 AM SET MENU Option menu 3 OPTION MENU Parameter Features Page A)DISPLAY SET Adjusts the brightness of the front panel display and the way in which iPod information is displayed. 59 B)MEMORY GUARD Locks sound field program parameters and other “SET MENU” settings. 60 C)AUDIO SELECT Designates the default audio input jack select setting for the input sources connected to the DIGITAL INPUT jacks when you turn on the power of this unit.
01EN_DSP-AX563_B.book Page 51 Friday, February 1, 2008 11:08 AM SET MENU 1 SOUND MENU Use this menu to manually adjust any speaker settings or compensate for video signal processing delays when using LCD monitors or projectors. ;MANUAL SETUP Front speakers FRONT SP Choices: SMALL, LARGE ;MANUAL SETUP 1 SOUND MENU 1/2 1 SOUND MENU 2/2 . F)DYNAMIC RANGE G)AUDIO SET H)HDMI SET I)EXTD SUR. 1 SOUND MENU A)SPEAKER SET FRONT SP p p [ ]/[ ]:Up/Down [ENTER]:Enter p p .
01EN_DSP-AX563_B.book Page 52 Friday, February 1, 2008 11:08 AM SET MENU Surround left/right speakers Choices: NONE, SML, LRG SUR. L/R SP LFE Bass out LFE/BASS OUT Use this feature to select the speakers that output the LFE (low-frequency effect) and the low-frequency signals. Choices: SWFR, FRNT, BOTH 1 SOUND MENU A)SPEAKER SET SUR. L/R SP 1 SOUND MENU A)SPEAKER SET LFE/BASS OUT NONE >SML LRG SWFR FRNT>BOTH When the surround speakers are large Select “LRG” (large).
01EN_DSP-AX563_B.book Page 53 Friday, February 1, 2008 11:08 AM SET MENU Crossover CROSS OVER Use this feature to select the crossover frequency of all the speakers set to “SML” (or “SMALL”) in “SPEAKER SET” (see page 51). All frequencies below the selected frequency will be sent to the subwoofer or front speakers depending on the setting of “LFE/BASS OUT” in “SPEAKER SET” (see page 51).
01EN_DSP-AX563_B.book Page 54 Friday, February 1, 2008 11:08 AM SET MENU ■ Speaker distance C)SP DISTANCE Use this feature to manually adjust the distance of each speaker and the delay applied to the respective channel. Ideally, each speaker should be the same distance from the main listening position. However, this is not possible in most home situations.
01EN_DSP-AX563_B.book Page 55 Friday, February 1, 2008 11:08 AM SET MENU ■ Dynamic range F)DYNAMIC RANGE Use this feature to select the amount of dynamic range compression to be applied to your speakers or headphones. This setting is effective only when this unit is decoding Dolby Digital and DTS signals. 1 SOUND MENU F)DYNAMIC RANGE . SPEAKER;;;;;;MAX HEADPHONE;;;;MAX p p [ ]/[ ]:Up/Down [p]/[[]:Adjust Speaker SPEAKER Adjusts the speaker compression.
01EN_DSP-AX563_B.book Page 56 Friday, February 1, 2008 11:08 AM SET MENU ■ HDMI set H)HDMI SET ■ Extended surround I)EXTD SUR. Use this feature to select the component to play back HDMI audio signals. 1 SOUND MENU I)EXTD SUR. . >AUTO LAST EXTD SUR.
01EN_DSP-AX563_B.book Page 57 Friday, February 1, 2008 11:08 AM SET MENU 2 INPUT MENU Use this menu to reassign the input jacks, select the decoder mode or rename the input source. For OPTICAL OUTPUT jack 4 OPTICAL OUT (4) Choices: (4) MD/CD-R, DTV/CBL, V-AUX, DVR 2 INPUT MENU ;MANUAL SETUP A)I/O ASSIGNMENT OPTICAL OUT . (4);;;;;MD/CD-R (MD/CD-R ) 2 INPUT MENU [p]/[[]:Select p p .
01EN_DSP-AX563_B.book Page 58 Friday, February 1, 2008 11:08 AM SET MENU ■ Input rename B)INPUT RENAME Use this feature to change the name of the input source that appears in the OSD and in the front panel display. 2 INPUT MENU B)INPUT RENAME DVD -> DVD 1 p p [p]/[[]:Position [ ]/[ ]:Chara. ■ Volume trim C)VOLUME TRIM Use this feature to adjust the output volume of each source.
01EN_DSP-AX563_B.book Page 59 Friday, February 1, 2008 11:08 AM SET MENU ■ Multi channel input setup E)MULTI CH SET 2 INPUT MENU 3 OPTION MENU Use this menu to adjust the optional system parameters. E)MULTI CH SET BGV;;;;;;;;;LAST INPUT CH;;;;;6CH ;MANUAL SETUP ;MANUAL SETUP 3 OPTION MENU [p]/[[]:Select p [ ]/[ ]:Up/Down [ENTER]:Enter If the connected component outputs discrete 6-channel audio signals. Select “6CH”. If the connected component outputs discrete 8-channel audio signals. Select “8CH”.
01EN_DSP-AX563_B.book Page 60 Friday, February 1, 2008 11:08 AM SET MENU Front panel display scroll FL SCROLL Use this feature to set whether to display the information (such as a song title or a channel name) in the front panel display in a continuous manner or by the first 14 alphanumeric characters after scrolling all characters once when “DOCK” is selected as the input source. Choices: CONT, ONCE • Select “CONT” to display the operation status in the front panel display in a continuous manner.
01EN_DSP-AX563_B.book Page 61 Friday, February 1, 2008 11:08 AM SET MENU ■ Parameter initialization D)PARAM. INI ■ Bluetooth setting E)BLUETOOTH SET Use this feature to set all the parameters of the sound field programs to the initial factory settings. Choices: NO, YES 3 OPTION MENU E)BLUETOOTH SET . START PAIRING 3 OPTION MENU D)PARAM. INI [ENTER]:Enter >NO YES [p]/[[]:Select [ENTER]:Return • Select “NO” to cancel the parameter initialization and return to the previous menu screen.
01EN_DSP-AX563_B.book Page 62 Friday, February 1, 2008 11:08 AM SET MENU ■ USB playback styles F)USB PLAY STYLE Use this feature to adjust the playback style according to your preference. You can shuffle files in a random order or repeat one specific file or a sequence of files. 3 OPTION MENU F)USB PLAY STYLE REPEAT.......OFF . SHUFFLE......OFF p p [ ]/[ ]:Up/Down [p]/[[]:Select Repeat REPEAT Use this feature to set this unit to repeat one file or a sequence of files.
01EN_DSP-AX563_B.book Page 63 Friday, February 1, 2008 11:08 AM Remote control features Remote control features In addition to controlling this unit, the remote control can also operate other audiovisual components made by Yamaha and other manufacturers. To control your TV or other components, you must set up the appropriate remote control code for each input source (see page 65).
01EN_DSP-AX563_B.book Page 64 Friday, February 1, 2008 11:08 AM Remote control features ■ Controlling other components Press one of the input selector buttons (3) or A to D buttons to control other components. You must set the appropriate remote control code for each input source in advance (see page 65). The following table shows the function of each control button used to control other components assigned to each input selector button.
01EN_DSP-AX563_B.book Page 65 Friday, February 1, 2008 11:08 AM Remote control features Setting remote control codes 1 You can control other components by setting the appropriate remote control codes. For a complete list of available remote control codes, refer to “List of remote control codes” at the end of this manual. While pressing and holding one of the input selector buttons (3) on the remote control to select the input area you want to set up, press 2 AV POWER for more than 3 seconds.
01EN_DSP-AX563_B.book Page 66 Friday, February 1, 2008 11:08 AM Advanced setup Advanced setup This unit has additional menus that are displayed in the front panel display. The advanced setup menu offers additional operations to adjust and customize the way this unit operates. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening environment.
01EN_DSP-AX563_B.book Page 67 Friday, February 1, 2008 11:08 AM Troubleshooting Troubleshooting Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. ■ General Problem This unit fails to turn on or enters the standby mode soon after the power is turned on. No sound.
01EN_DSP-AX563_B.book Page 68 Friday, February 1, 2008 11:08 AM Troubleshooting Problem The sound suddenly goes off. Cause Remedy See page The protection circuitry has been activated because of a short circuit, etc. Check that the speaker wires are not touching each other and then turn this unit back on. — The sleep timer has turned off this unit. Turn on this unit, and play the source again. — The sound is muted. Press IMUTE or L VOLUME +/– to resume audio output.
01EN_DSP-AX563_B.book Page 69 Friday, February 1, 2008 11:08 AM Troubleshooting Problem Cause Remedy See page Dolby Digital or DTS sources cannot be played. (Dolby Digital or DTS indicator in the front panel display does not light up.) The connected component is not set to output Dolby Digital or DTS digital signals. Make an appropriate setting following the operating instructions for your component. — Audio input jack select is set to “ANALOG”. Set Audio input jack select to “AUTO”.
01EN_DSP-AX563_B.book Page 70 Friday, February 1, 2008 11:08 AM Troubleshooting ■ AUTO SETUP Before AUTO SETUP Error message Connect MIC! Unplug HP! Cause Optimizer microphone is not connected. Headphones are connected. Remedy See page Connect the supplied optimizer microphone to the OPTIMIZER MIC jack on the front panel. 24 Unplug the headphones. — During AUTO SETUP Error message Cause Remedy See page E-1:NO FRONT SP Front L/R channel signals are not detected.
01EN_DSP-AX563_B.book Page 71 Friday, February 1, 2008 11:08 AM Troubleshooting After AUTO SETUP Warning message Cause Remedy See page W-1:OUT OF PHASE Speaker polarity is not correct. This message may appear depending on the speakers even when the speakers are connected correctly. Check the speaker connections for proper polarity (+ or –). 12 W-2:OVER 24m (80ft) The distance between the nearest speaker and the furthest speaker is out of adjustable range.
01EN_DSP-AX563_B.book Page 72 Friday, February 1, 2008 11:08 AM Troubleshooting ■ USB Cause The music files and directories in the USB device cannot be viewed. The music files and directories are placed in locations other than the FAT area. Place music files and directories in the FAT area. You are attempting to browse directory hierarchies of over 8 levels or a directory with more than 500 files. Modify the data structure on your USB device. The USB device cannot be recognized.
01EN_DSP-AX563_B.book Page 73 Friday, February 1, 2008 11:08 AM Troubleshooting ■ iPod Note In case of a transmission error without a status message appearing in the front panel and in the OSD, check the connection to your iPod (see page 20). Status message Loading... Cause Remedy See page This unit is in the middle of recognizing the connection with your iPod. This unit is in the middle of acquiring song lists from your iPod.
01EN_DSP-AX563_B.book Page 74 Friday, February 1, 2008 11:08 AM Troubleshooting ■ Bluetooth Status message Searching... Cause Remedy See page The Bluetooth adapter and the Bluetooth component is in the middle of the pairing. The Bluetooth adapter and the Bluetooth component is in the middle of establishing the connection. Completed The paring is completed. Not found The Bluetooth adapter cannot find the Bluetooth component. Canceled The paring is canceled.
01EN_DSP-AX563_B.book Page 75 Friday, February 1, 2008 11:08 AM Troubleshooting ■ Remote control Problem The remote control does not work nor function properly. Cause Remedy See page Wrong distance or angle. The remote control functions within a maximum range of 6 m (20 ft) and no more than 30 degrees offaxis from the front panel. 23 Direct sunlight or lighting (from an inverter type of fluorescent lamp, etc.) is striking the remote control sensor of this unit. Reposition this unit.
01EN_DSP-AX563_B.book Page 76 Friday, February 1, 2008 11:08 AM Glossary Glossary ■ Bi-amplification connection ■ Dolby Digital A bi-amplification connection uses two amplifiers for a speaker. One amplifier is connected to the woofer section of a loudspeaker while the other is connected to the combined mid and tweeter section. With this arrangement each amplifier operates over a restricted frequency range.
01EN_DSP-AX563_B.book Page 77 Friday, February 1, 2008 11:08 AM Glossary ■ Dolby Surround ■ LFE 0.1 channel Dolby Surround uses a 4-channel analog recording system to reproduce realistic and dynamic sound effects: 2 front left and right channels (stereo), a center channel for dialog (monaural), and a surround channel for special sound effects (monaural). The surround channel reproduces sound within a narrow frequency range.
01EN_DSP-AX563_B.book Page 78 Friday, February 1, 2008 11:08 AM Glossary ■ SILENT CINEMA Yamaha has developed a natural, realistic sound effect DSP algorithm for headphones. Parameters for headphones have been set for each sound field so that accurate representations of all the sound field programs can be enjoyed on headphones.
01EN_DSP-AX563_B.book Page 79 Friday, February 1, 2008 11:08 AM Specifications Specifications AUDIO SECTION VIDEO SECTION • Minimum RMS Output Power for Front, Center, Surround, Surround Back 1 kHz, 0.9% THD, 6 Ω ......................................................... 90 W • Video Signal Type (Gray back).................................................. PAL • Video Signal Type (Video Conversion) .......................... NTSC/PAL • Dynamic Power IHF, 6/4/2 Ω ........................................
01EN_DSP-AX563_B.book Page 80 Friday, February 1, 2008 11:08 AM INDEX Index ■ Numerics 1 SOUND MENU, Manual setup ........ 49 2 INPUT MENU, Manual setup .......... 49 2ch Enhancer, Sound field program .... 38 2ch Stereo, Sound field program ......... 38 3 OPTION MENU ............................... 59 3 OPTION MENU, Manual setup ....... 50 7ch Enhancer, Sound field program .... 38 7ch Stereo, Sound field program ......... 38 96/24 indicator .....................................
01EN_DSP-AX563_B.book Page 81 Friday, February 1, 2008 11:08 AM Index Headphone, Dynamic range ................. 55 HEADPHONE, Low-frequency effect level ................................................. 54 Headphone, Low-frequency effect level .............. 54 Headphones .......................................... 35 Headphones indicator .......................... 22 High quality sound ............................... 41 ■ I I) EXTD SUR., Sound menu ............... 56 Infrared window, Remote control ..
01EN_DSP-AX563_B.book Page 82 Friday, February 1, 2008 11:08 AM Index SUBWOOFER PHASE, Speaker settings ............................... 53 Subwoofer phase, Speaker settings ...... 53 SUPPORT AUDIO, HDMI set ............ 56 Support audio, HDMI set ..................... 56 SUR. L/R SP, Speaker settings ............ 52 Surround back left/right speakers, Speaker settings ............................................. 52 Surround left/right speakers, Speaker settings ............................................
01EN_DSP-AX563_B.book Page 83 Friday, February 1, 2008 11:08 AM Limited Guarantee for European Economic Area (EEA) and Switzerland Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service, please contact the dealer from whom it was purchased. If you experience any difficulty, please contact Yamaha representative office in your country. You can find full details on our website (http://www.yamaha-hifi.com/ or http://www.yamaha-uk.com/ for U.K.
01EN_DSP-AX563_B.
01EN_DSP-AX563_B.book Page ii Friday, February 1, 2008 11:08 AM ■ Remote control 1 2 3 POWER POWER TV AV USB STANDBY POWER A B MUTE CD MD/CD-R TUNER DVD DTV/CBL DVR V-AUX/DOCK C D AMP TV INPUT TV MUTE 1 2 G H I TV CH J TV VOL 4 SCENE 5 6 BAND LEVEL TITLE 7 8 3 4 VOLUME MENU L ENTER DISPLAY RETURN MEMORY K M REC 9 0 l EON PROG h MODE - PTY SEEK - START ENHANCER SUR.
01EN_DSP-AX563_B.
01EN_DSP-AX563_B.
01EN_DSP-AX563_B.
01EN_DSP-AX563_B.
DSP-AX563_B-cv.
00_sheet_DSP-AX563_B.book Page 1 Friday, February 1, 2008 11:17 AM B DSP-AX563 The circled numbers and alphabets correspond to those in the Owner’s Manual.
00_sheet_DSP-AX563_B.book Page i Friday, February 1, 2008 11:17 AM ■ Remote control 1 2 3 POWER POWER TV AV USB STANDBY POWER A B MUTE CD MD/CD-R TUNER DVD DTV/CBL DVR V-AUX/DOCK C D AMP TV INPUT TV MUTE 1 2 G H I TV CH J TV VOL 4 SCENE 5 6 BAND LEVEL TITLE 7 8 3 4 VOLUME MENU L ENTER DISPLAY RETURN MEMORY K M REC 9 0 A B C D E F FREQ/TEXT l EON PROG h MODE - PTY SEEK - START ENHANCER SUR.