Owner's Manual

80 En
Graphical user interface (GUI) menu
4 Press
9
n to select “EDIT” and press
9
ENTER to access the edit window.
For more information on the parametric equalizer and
each parameter, see page 132.
The parameter selected in “PARAM” is highlighted.
• Press
9
l / h to adjust the parameter.
• Press
9
k / n to adjust the “Gain”.
• Press
9
ENTER to exit the edit window.
y
• When you select “Band” in step 3, you can use this menu
as a graphic equalizer.
• “Band #5”, “Band #6”, and “Band #7” can adjust the
frequencies of above 500 Hz.
• When you select “Subwoofer” in step 1 and “Band” in step 3,
you can adjust “Band #1”, “Band #2”, “Band #3” and “Band
#4” only. In this case, “Band #1”, “Band #2”, “Band #3” and
“Band #4” adjust the frequencies of below 200 Hz.
5 Repeat steps 3 and 4 until you are satisfied
with the results.
y
If you want to reset all “Parametric EQ” parameter settings
for the selected speaker, select “RESET” and press
9ENTER.
6 Select “EXIT” and press
9
ENTER to exit
from the settings window.
■ Tone Control (Tone control)
Use this feature to adjust the balance of bass and treble
output to your speakers or headphones.
Tone Control is not effective when:
– the PURE DIRECT mode (page 53) is selected.
– MULTI CH is selected as the input source.
Control (Control mode)
y
“Speaker” and “Headphone” adjustments are stored
independently. The adjustments for “Speaker” affects the front
left/right speaker, center speaker and subwoofer channels.
Bass (Bass control)
Use this feature to adjust low-frequencies output to your
speakers or headphones.
Choices: 125 Hz, 350 Hz, 500 Hz
Control range: –6.0 dB to +6.0 dB
Initial setting: 0.0 dB
Treble (Treble control)
Use this feature to adjust high-frequencies output to your
speakers or headphones.
Choices: 2.5 kHz, 3.5 kHz, 8.0 kHz
Control range: –6.0 dB to +6.0 dB
Initial setting: 0.0 dB
Auto Bypass (Auto bypass)
Use this feature to select whether the audio output
bypasses the tone control circuitry when “Treble” and
“Bass” are set to 0 dB.
■ Lipsync
(Audio and video synchronization)
Mode (HDMI automatic lip sync mode)
If the video monitor is connected to the HDMI OUT jack
of this unit and compatible with the automatic audio and
video synchronization function (automatic lip sync), this
unit adjusts the audio and video synchronization
automatically. Use this feature to activate or deactivate the
automatic lip sync.
When “HDMI OUT SEL” is set to “OUT 1+2” and video
monitors are connected to both the HDMI OUT 1 and HDMI
OUT 2 jacks, the automatic lip sync function does not work
even if “Auto” is selected.
Auto (Automatic audio delay adjustment)
Use this feature to make fine adjustments of the audio and
video synchronization when you set “Mode” to “Auto”.
Control range: 0 to 240 ms
Control step: 1 ms
Note
Choice Functions
Speaker
Adjust the bass/treble balance of your speakers.
Headphone
Adjust the bass/treble balance of your
headphones.
PEQ Data Copy
PEQ Select
Front L
Front R
Center
Band #1
Gain 0.0dB
Freq 62.5Hz
Q1.000
Exit:ENTER
Choice Functions
Auto
Automatically bypasses the tone control
circuitry to provide the purest signal possible
when “Treble” and “Bass” are set to 0 dB.
Off
Does not bypass the tone control circuitry.
Choice Descriptions
Auto
Select this setting if the connected video
monitor is compatible with the automatic lip
sync. Use “Auto” to fine adjust the audio and
video synchronization.
Manual
Select this setting if the video monitor is not
compatible with the automatic lip sync or you
do not want to use the automatic lip sync. Use
“Manual” to adjust the audio and video
synchronization.
Note