Specifications

24 25
Dimensions
PM5D V2 ANALOG INPUT CHARACTERISTICS
PM5D-RH V2 ANALOG INPUT CHARACTERISTICS
Input Terminals PAD GAIN
Actual Load
For Use With Nominal GAIN SW
*4
Input Level
Connector
Impedance
Sensitivity
*1
Nominal Max. Before Clip
0
-60dB -80dBu (0.0775mV) -60dBu (0.775mV) -40dBu (7.75mV)
INPUT 1 – 48
-16dB
3kΩ 50-600Ω Mics & 600Ω Lines — -36dBu (12.3mV) -16dBu (123mV) +4dBu (1.23V) XLR-3-31 Type (Balanced)
*2
26 -10dBu (245mV) +10dBu (2.45V) +30dBu (24.51V)
STEREO INPUT 1 – 4 [L, R]
-34dB
4kΩ 600Ω Lines —
-54dBu (1.55mV) -34dBu (15.5mV) -14dBu (155mV)
XLR-3-31 Type (Balanced)
*2
10dB -10dBu (245mV) +10dBu (2.54V) +30dBu (24.51V)
INSERT IN 1 – 48 10kΩ 600Ω Lines — -16dBu (123mV) +4dBu (1.23V) +24dBu (12.28V) Phone Jack (TRS) (Balanced)
*3
2TR IN ANALOG 1, 2 [L, R] 10kΩ 600Ω Lines
+24dB (default) -6dBu (388mV) +4dBu (1.23V) +24dBu (12.28V)
XLR-3-31 Type (Balanced)
*2
+18dB -12dBu (195mV) -2dBu (0.616V) +18dBu (6.16V)
TALKBACK 3kΩ 50-600Ω Mics & 600Ω Lines — -60dBu (0.775mV) -50dBu (2.45mV) -30dBu (24.5mV) XLR-3-31 Type (Balanced)
*2
PM5D V2/PM5D-RH V2 ANALOG OUTPUT CHARACTERISTICS
Output Terminals
Actual Source
For Use With Nominal GAIN SW
*4
Output Level
Connector
Impedance
Nominal Max. Before Clip
STEREO A, B [L, R] 150Ω 600Ω Lines
+24dB (default) +4dBu (1.23 V) +24dBu (12.28 V)
XLR-3-32 Type (Balanced)
*1
+18dB -2dBu (616mV) +18dBu (6.16V)
MONITOR OUT [L, R, C] 150Ω 600Ω Lines
+24dB (default) +4dBu (1.23 V) +24dBu (12.28 V)
XLR-3-32 Type (Balanced)
*1
+18dB -2dBu (616mV) +18dBu (6.16V)
CUE OUT [L, R] 150Ω 600Ω Lines
+24dB (default) +4dBu (1.23 V) +24dBu (12.28 V)
XLR-3-32 Type (Balanced)
*1
+18dB -2dBu (616mV) +18dBu (6.16V)
MATRIX OUT 1 – 8 150Ω 600Ω Lines +24dB (default) +4dBu (1.23 V) +24dBu (12.28 V)
XLR-3-32 Type (Balanced)
*1
+18dB -2dBu (616mV) +18dBu (6.16V)
MIX OUT 1 – 24 150Ω 600Ω Lines +24dB (default) +4dBu (1.23 V) +24dBu (12.28 V)
XLR-3-32 Type (Balanced)
*1
+18dB -2dBu (616mV) +18dBu (6.16V)
INSERT OUT 1 – 48 150Ω 10kΩ Lines — +4dBu (1.23 V) +24dBu (12.28 V) Phone Jack (TRS) (Balanced)
*2 *5
PHONES (x2) 15Ω 8Ω Phones — 75mW (*6) 150mW Stereo Phone Jack (TRS)
40
Ω Phones — 65mW (*6) 150mW (Unbalanced)
*3
Input Terminals GAIN
Actual Load
For Use With Nominal GAIN SW
*4
Input Level
Connector
Impedance
Sensitivity
*1
Nominal Max. Before Clip
INPUT 1 – 48
-62dB
3kΩ 50-600Ω Mics & 600Ω Lines —
-82dBu (61.6µV) -62dBu (0.616mV) -42dBu (6.16mV)
XLR-3-31 Type (Balanced)
*2
+10dB -10dBu (245mV) +10dBu (2.45V) +30dBu (24.5V)
STEREO INPUT 1 – [L, R]
-62dB 3kΩ
50-600Ω Mics & 600Ω Lines —
-82dBu (61.6µV) -62dBu (0.616mV) -42dBu (6.16mV)
XLR-3-31 Type (Balanced)
*2
+10dB -10dBu (245mV) +10dBu (2.45V) +30dBu (24.5V)
2TR IN ANALOG 1, 2 [L, R] 10kΩ 600Ω Lines
+24dB (default) -6dBu (388mV) +4dBu (1.23V) +24dBu (12.28V)
XLR-3-31 Type (Balanced)
*2
+18dB -12dBu (195mV) -2dBu (0.616V) +18dBu (6.16V)
TALKBACK 3kΩ 50-600Ω Mics & 600Ω Lines — -60dBu (0.775mV) -50dBu (2.45mV) -30dBu (24.5mV) XLR-3-31 Type (Balanced)
*2
*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are maximum position.)
*2. XLR-3-31 type connectors are balanced. (1 = GND, 2 = HOT, 3 = COLD)
*3. Phone jacks are balanced. (Tip = HOT, Ring = COLD, Sleeve = GND)
*4. There are switches inside the body to preset the maximum input level.
• In these specifications, 0dBu = 0.775 V rms.
• All input AD converters are 24bit linear, 128times (@48kHz) oversampling.
• +48V DC (phantom power) is supplied to INPUT (1 – 48) XLR type connectors via each individual switch.
*1. XLR-3-32 type connectors are
balanced. (1 = GND, 2 = HOT,
3 = COLD)
*2. Phone jack are balanced.
(Tip = HOT, Ring = COLD,
Sleeve = GND)
*3. PHONES stereo phone jack is
unbalanced. (Tip = LEFT,
Ring = RIGHT, Sleeve = GND)
*4. There are switches inside the
body to preset the maximum
output level.
*5. INSERT OUTs are only provided
for PM5D.
*6. The position of the level control is
10dB lowered from Max.
• In these specifications,
0dBu = 0.775 Vrms.
• All output DA converters are 24bit,
128times (@48kHz) oversampling.
PM5D V2/PM5D-RH V2 SLOT (1-4) CHARACTERISTICS
Card Name Function Input Output
The Number Of
Usable Cards
MY4-AD ANALOG IN 4 IN — 4
MY8-AD24 ANALOG IN 8 IN — 4
MY8-AD96 ANALOG IN 8 IN — 4
MY4-DA ANALOG OUT — 4 OUT 4
MY8-DA96 ANALOG OUT — 8 OUT 4
MY8-AE96 AES/EBU 8 IN 8 OUT 4
MY8-AE96S AES/EBU 8 IN 8 OUT 4
PM5D V2/PM5D-RH V2 DIGITAL INPUT CHARACTERISTICS
Terminal Format Data Length Level Connector
2TR IN 1 AES/EBU AES/EBU 24bit RS422 XLR-3-31 Type (Balanced)
*1
DIGITAL
2 AES/EBU AES/EBU 24bit RS422 XLR-3-31 Type (Balanced)
*1
(*2)
3 COAXIAL IEC-60958 24bit 0.5Vpp/75Ω RCA Pin Jack
CASCADE IN — — RS422
D-Sub Half Pitch Connector 68P (Female)
*1. XLR-3-31 type connectors are balanced. (1 = GND, 2 = HOT, 3 = COLD)
*2. With Sampling Rate Converter.
Each I/O SLOT accepts a Digital Interface card.
PM5D V2/PM5D-RH V2 DIGITAL OUTPUT CHARACTERISTICS
Terminal Format Data Length Level Connector
2TR OUT
1 AES/EBU
AES/EBU
24bit
*1
RS422 XLR-3-32 Type (Balanced)
*2
DIGITAL Professional Use
(*3)
2 AES/EBU
AES/EBU
24bit
*1
XLR-3-32 Type (Balanced)
*2
Professional Use
3 COAXIAL
IEC-60958
24bit
*1
0.5Vpp/75Ω RCA Pin Jack
Consumer Use
CASCADE OUT — — RS422 D-Sub Half Pitch Connector 68P (Female)
*1. Dither :word length 16/20/24 bit
*2. XLR-3-32 type connectors are balanced. (1 = GND, 2 = HOT, 3 = COLD)
*3. With Sampling Rate Converter.
Specifications and appearance are subject to change without notice.
All trademarks and registered trademarks are property of their respective owners.
*Only SLOT1 has a Serial Interface.
Card Name Function Input Output
The Number Of
Usable Cards
MY8-AT ADAT 8 IN 8 OUT 4
MY8-TD TASCAM 8 IN 8 OUT 4
MY8-AE AES/EBU 8 IN 8 OUT 4
MY16-AT ADAT 16 IN 16 OUT 4
MY16-TD TASCAM 16 IN 16 OUT 4
MY16-AE AES/EBU 16 IN 16 OUT 4
MY16-C* CobraNet 16 IN 16 OUT 4
PM5D V2/PM5D-RH V2 CONTROL INPUT/OUTPUT CHARACTERISTICS
Terminal Format Level Connector
TO HOST USB USB1.1 0V-3.3V B type USB Connector
MIDI IN MIDI — DIN-5pin
OUT MIDI — DIN-5pin
THRU MIDI — DIN-5pin
TIME CODE IN SMPTE SMPTE 0.3Vpp(min.)/10Vpp(max.), 10kΩ XLR-3-31 type
WORD CLOCK IN — TTL/75Ω(ON/OFF) BNC
OUT — — BNC
GPI — TTL/75Ω D-sub 25pin(female)
HA REMOTE — — D-sub 9pin(male)
REMOTE — RS422 D-sub 9pin(female)
KEYBOARD PS/2 RS422 DIN 6pin
MOUSE PS/2 — DIN 6pin
]
LAMP 1,2,3 — 2.5V-11.5V XLR-4-31 type
MEMORY CARD — — PCMCIA(CF)
DSP5D ANALOG INPUT CHARACTERISTICS
Input Terminals GAIN Actual Load Impedance For Use With Nominal
Output Level
Connector
Sensitivity
*1
Nominal Max. Before Clip
INPUT 1 – 48
-62dB
3kΩ
50-600Ω Mics. & -82dBu -62dBu -42dBu
XLR-3-31 Type
+10dB
600Ω Lines -10dBu -10dBu +30dBu
(Balanced)
*2
ST IN 1 – 4 [L, R]
-62dB
3kΩ
50-600Ω Mics. & -82dBu -62dBu -42dBu
XLR-3-31 Type
+10dB
600Ω Lines -10dBu -10dBu +30dBu
(Balanced)
*2
*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (all faders and level controls are maximum position.)
*2. XLR-3-31 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)
*3. All input AD converters are 24bit linear, 128times (@48kHz) oversampling.
*4. +48V DC (phantom power) is supplied to INPUT (1 – 48) XLR type connectors via one master software controled switch and each individual software controled switches.
*5. There are switches inside the body to preset the maximum input level.
DSP5D ANALOG OUTPUT CHARACTERISTICS
Output Terminals Actual Source Impedance For Use With Nominal GAIN SW
*5
Output Level
Connector
Nominal Max. Before Clip
OMNI OUT – 24 150kΩ 600Ω Lines
+24dB (default) +4dBu +24dBu
XLR-3-32 Type (Balanced)
*1
+18dB -2dBu +18dBu
*1. XLR-3-32 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)
*2. All output DA converters are 24bit, 128times (@48kHz) oversampling.
*3. There are switches inside the body to preset the maximum output level.
DSP5D DIGITAL INPUT CHARACTERISTICS
Terminal Format Data Length Level Connector
CASCADE IN — — RS422 D Sub Half Pitch Connector 68P (Female)
CASCADE IN — — 100 Base-TX (RJ-45) Ether-Con
*1. CASCADE cable max. 200m@48KHz, 50m@96KHz.
DSP5D DIGITAL OUTPUT CHARACTERISTICS
Terminal Format Data Length Level Connector
CASCADE OUT — — RS422 D Sub Half Pitch Connector 68P (Female)
CASCADE OUT — — 100 Base-TX (RJ-45) Ether-Con
*1. CASCADE cable max. 200m@48KHz, 50m@96KHz.
283
271
260
283
271
260
1551
1450
950 865
1551
1450
950 865
Unit: mmUnit: mm
PM5D-RH V2
PM5D V2