User Manual
Table Of Contents
- Cover
- Contents
- Differences Between the DTX-PRO and the DTX-PROX
- Links from the Owner’s Manuals
- How the Triggers Generate Sounds
- The Relationship Between Trigger Input Jacks, Trigger Inputs, and Trigger Input Sources
- Trigger Input Jack Input Mode
- Sounds that are played by trigger (Inst and Voice)
- Voices and Layers
- User Voices
- Importing to User Voices
- Changing the way a user voice is played (one-shot or Loop)
- Editing and auditioning user voices
- Selecting the Trigger Input or Trigger Input Source
- Effect Processor Design
- PRO Series Modules Internal Memory
- MENU Button
- KIT Mode
- CLICK Mode
- RECORDER Mode
- Practicing with the Training Feature
- Fader Select FX
- Fader Select CUSTM
- LIVE SET Mode
- Settings for live performances
- Connecting a Computer
- Troubleshooting
- Reference
Troubleshooting
140
DTX-PRO DTX-PROX Reference Manual
Pads are only produc-
ing sounds at very high
volumes (i.e., high
velocities)
• Ensure that the “Gain” parameter from MENU/Trigger/Pad Type
or TRIGGER/SETTING/Pad Type is not set too high.
• Adjust the “Velocity Curve” parameter from MENU/Trigger/
Curve or TRIGGER/SETTING/Curve.
• Check the “TrgVel ” setting in MENU/Kit Edit/Kit Modifier/Voice/
MessageType. For example, if this parameter is set to “127,” the
maximum velocity will be produced even when the pad is struck
lightly.
• Ensure that you are using only the recommended Yamaha pads.
Products from other manufacturers can output excessively large
signals.
Pads produce
unintended sounds
• Ensure that trigger setups have been configured correctly.
• If an external MIDI device played from the PRO series module
does not produce the expected sounds, review its voice settings
for the MIDI channel on which the PRO series module is sending
data, and ensure that they are appropriate for the MIDI data
being sent.
• Voices assigned to layers B, C, or D may cause unintended
sounds.
• In some cases where unexpected sounds are produced when
you have connected a two or three-zone pad to any of the
[
wTOM1/e], [rTOM2/t], [yTOM3/u], [!2KICK/!3],
[
qSNARE] or [!4] jacks. If so, with Pad 3, Pad 5, Pad 7 or Pad
13, set the “Pad Type” parameter to “off” in MENU/Trigger/Pad
Ty p e or TRIGGER/SETTING/Pad Type. With Pad 1 or Pad 14,
select the proper pad type in MENU/Trigger/Pad Type or TRIG-
GER/SETTING/Pad Type.
• Check the crosstalk setting, min level setting and sensitivity set-
ting.
Sounds are distorted • Ensure that effects have been set appropriately. Sound can be
distorted with certain combinations of effect type and parameter
settings.
• Ensure that the “VoiceFilter” parameter in MENU/Kit Edit/Voice
is configured properly. Depending on the VoiceQ settings (filter
resonance), distortion can be caused.
• Lower the PRO series module’s master volume.
Sounds play endlessly
and do not stop
Ensure that the hold function is not turned on.
Press [EXIT] while on the kit screen (top screen) to stop the KIT
sounds.
Effects cannot be
applied
• Ensure that the [EFFECT] knob is not turned down to minimum.
• Ensure that the effect type is not set to “THRU” or “NO EFFECT.”
• Ensure that the InstSend value is high enough for Effect 1 or
Effect 2.
Effects may not be applied to
the output via Indiv Out. Master
effects will not be applied.
Insertion effects may not be
applied depending on the set-
tings.
The wave tempo does
not change
Wave tempo cannot be changed. It will always play at the original
tempo of the imported file regardless of kit tempo and other set-
tings.
Pad controller does not
work
Pad controllers are not supported.
By pressing the [REC]
button, only one song
can be recorded. The
previous recording is
overwritten
Only one song can be recorded to the PRO series modules.
My training scores are
strange
Crosstalk is occurring See the section on “Crosstalk.”
Symptom Possible cause
Solution
DTX-PRO DTX-PROX