Page -1 Friday, December 24, 2010 9:15 AM Deutsch English rs500_700_en_1224.
rs500_700_en_1224.fm Page 0 Friday, December 24, 2010 9:15 AM For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich.
rs500_700_en_1224.fm Page 1 Friday, December 24, 2010 9:15 AM English PRECAUTIONS Before using, please read this assembly manual, and use this product in a safe and proper manner. * Please keep this manual in a safe place for future reference. WARNING If this symbol is ignored and the equipment is used improperly, fatal injury to persons or serious damage could occur. • Do not let small children assemble or set up this product by themselves, or they may be injured.
rs500_700_en_1224.fm Page 2 Friday, December 24, 2010 9:15 AM Setting up RS500 1. Remove the rack from its box and stand it up with the drum trigger module clamp and the left leg positioned on the right as shown in Figure 1. 2. With the rack standing up, loosen the bolts q located on the left and rotate the left leg towards you until it is positioned as shown in Figure 1 Top view. • The bolts q can be found on the rear of the clamp on the left pillar.
rs500_700_en_1224.fm Page 3 Friday, December 24, 2010 9:15 AM 5. Loosen the bolt r, and as shown in Figure 3, raise up the cymbal holder located on the left. Following this, retighten the bolt r. • When tightening the bolt, ensure that the black sleeve is positioned inside the clamp’s mounting hole. 6. Loosen the bolts t, and as shown in Figure 3, rotate upward the cymbal holder located on the right. Following this, retighten the bolts t. 7.
rs500_700_en_1224.fm Page 4 Friday, December 24, 2010 9:15 AM Setting up RS700 1. Remove the rack from its box and stand it up with the drum trigger module clamp positioned on the right as shown in Figure 1. 2. With the rack standing up, loosen the bolts q located on the right and rotate the right leg clockwise from the left until it comes fully around as shown in Figure 1 Top view. • The bolts q can be found on the rear of the clamp on the right pillar, which is located behind the left leg.
rs500_700_en_1224.fm Page 5 Friday, December 24, 2010 9:15 AM 5. Loosen the bolts of the tom holders and rotate the three tom holders into the positions shown in Figure 3. Then, retighten the bolts.
rs500_700_en_1224.fm Page 6 Friday, December 24, 2010 9:15 AM Adjusting the RS500 or RS700 If your rack is unstable even on a flat surface, check whether the slits in the clamps q to r from Figure 1 line up with the arrows on the horizontal pipes as shown in Figure 2. If this is not the case, loosen each of the clamp bolts t, adjust the horizontal pipes such that the arrows line up with the slits, and then retighten the bolts.
rs500_700_ja_1224.
rs500_700_ja_1224.fm Page 10 Friday, December 24, 2010 9:15 AM Yamaha Electronic Drums web site: http://dtxdrums.yamaha.com Yamaha Manual Library: http://www.yamaha.co.jp/manual/ U.R.G., Digital Musical Instruments Division © 2011 Yamaha Corporation 101PO***.