manual

Mounting the drum trigger module and cymbal pads
 Mounting the drum trigger module
1. Attach the module stand (provided) to the underside
of the drum trigger module using the module stand
fastening screws.
2. Place the module stand inside the holder clamp and
tighten the clamp bolt to secure in position.
 Mounting the cymbal pads
1. Using a tuning key, loosen the stopper’s key bolt.
2. Remove the wing nut, the two felt pads, and the bolt
cover from the cymbal holder.
3. Place the stopper on the cymbal holder.
* If the key bolt was not sufficiently loosened in
Step 1 above, it may not be possible to pass the
stopper over the cymbal holder’s shaft. In such a
case, loosen the key bolt as much as possible
without removing it.
4. Replace the bolt cover.
* When assembling the bolt cover, turn until it no
longer rotates.
5. Secure the stopper in place. With the stopper mak-
ing full contact with the bottom surface of the bolt
cover, tighten the stopper’s key bolt using a tuning
key.
6. Place one of the felt pads removed in Step 2 on the
cymbal holder.
7. Mount the pad unit on the cymbal stand. Lower the
pad unit into place with the cymbal holder’s shaft
passing through the central hole of the cup section.
When mounted, the stopper’s pin should rest inside
the pad unit’s smaller hole.
* If you were to play a cymbal pad without the stop-
per’s pin positioned inside the smaller hole, the
pad could rotate, causing the cable to be pulled
out. It is very important, therefore, to ensure that
the stopper is secured as described in Step 5
above.
8. Assemble the felt pad that came with your pad unit.
* The second felt pad removed from the cymbal
holder in Step 2 above is not required for assem-
bly of your pad unit.
9. Tighten the wing nut to secure the pad unit to the
cymbal holder.
PCY135
PCY155
PCY135
Drum trigger
module
Module stand fastening
screws
Module stand
Drum trigger module
(back side)
Front of
module
Clamp bolt
Drum trigger
module
+
module stand
Insert
Holder clamp
Tuning key
Key bolt
Stopper
Cymbal holder
Felt pads
Bolt cover
Wing nut
Cymbal holder
Stopper
Bolt cover
Cymbal holder
Stopper
Bolt cover
Full contact
Pad unit
Felt pad that came
with pad unit
Cymbal holder
Felt pad
Bolt cover
Pad unit
Stopper
Pin
Wing nut
Stopper’s pin
Smaller
hole
Assembling the hi-hat stand
1. If a drum mat (sold separately) is not available, lay
a sheet of cardboard on the floor to protect it from
scratching.
2. Loosen the hi-hat stand’s wing bolt (a in the follow-
ing figure).
3. Extend the tripod legs to stabilize the stand.
Retighten the wing bolt loosened in Step 2.
4. Insert the radius rod into the frame hole as shown
below.
5. As shown on the right, loosen the wing bolt (b in the
figure) to remove the hi-hat clutch.
* This hi-hat clutch is not used within the standard
assembly example shown in this pamphlet. In-
stead, use the hi-hat clutch that came with your
RHH135.
6. Pull out the hi-hat shaft from the upper pipe
.
7. Screw the hi-hat shaft into the nut on the lower
pipe .
8. Insert the upper pipe into the hi-hat shaft
from above, and then tighten the wing bolt (c in the
figure) with the support plate positioned at the mid-
dle area of the hi-hat shaft .
9. Remove the felt washer located above the support
plate. It is not used within the standard assembly ex-
ample shown in this pamphlet.
10. Set up the RHH135 Real Hi-hat Pad.
* Refer to refer to the Setting Up section of the
owner’s manual that came with your RHH135.
Radius rod
Wing bolt a
Radius rod
Felt
washer
Hi-hat
clutch
Support
plate
Support
plate
c
b
Position the hi-hat stand, kick pad, and snare stand as desired, referring to the standard assembly example on the other side.
Before starting assembly, lay a drum mat (sold separately) on the floor. Alternatively, you can place the packages' cardboard
boxes on the floor under the hi-hat stand and kick pad to protect it from damage.
Connect the pads to the drum trigger module.
As described below, connect the output of each pad to the corresponding trigger input jack on the drum trigger module.
Connect the drum trigger module to a power supply.
This completes the assembly procedure.
* For information about tuning the power on/off, checking the actual sound, and other subsequent steps,
refer to the Setting Up section of the owner’s manual that came with your drum trigger module.
Assembling the kick pad
1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the
floor to protect it from scratching.
2. Remove the wing bolts, spring washers, and washers from the kick pad body,
and line up each set nearby in the order in which it was removed.
3. Join the base section to the body as shown below, and then secure it in place
by assembling the wing bolts, spring washers, and washers removed in the pre-
vious step from the base side.
Body
Body
Base
Washer
Spring washer
Wing bolt
Mounting the snare stand and pad
1. Open up the snare stand’s legs and stand it up on the floor.
2. Tighten the clamp bolt S onto the rear side of the snare pad.
3. Open up the snare stand’s basket section, lay the XP100SD Snare Pad on it,
adjust the basket, and then tighten the adjusting knob to secure the pad and
prevent it from moving.
Legs
Basket
XP100SD
(Snare pad)
Adjusting
knob
Clamp bolt S
4
NOTICE
5
1. Insert the 10-channel snake cable’s straight plugs into the drum trigger module’s
trigger input jacks ([q SNARE] to [o KICK/!0] and [HI-HAT CONTROL]).
• If you are using the standard setup, the stickers on each of the snake cable’s
plugs will indicate the name of the corresponding pad.
2. Plug the 10-channel snake cable’s L-shaped plugs into the correct pads.
3. In the case of snare and tom pads, wrap the cables around the cable clips to pre-
vent them from being pulled out.
Excessive bending can damage the pad cables. Ensure, there-
fore, that these cables are not bent at an extreme angle when
wrapped around the clips.
[Drum trigger module’s rear panel]
1098 7 6 54 32 1
[10-channel
snake cable]
Straight
plugs
L-shaped
plugs
Straight plug names
(as shown on stickers)
SNARE
TOM1
TOM2
TOM3
RIDE
CRASH
CRASH2
HI HAT
HH CON
KICK
DTX700 jack names
1: qSNARE
2: wTOM1
3: eTOM2
4: rTOM3
5: tRIDE
6: yCRASH1
7: uCRASH2
8: iHI-HAT
9: HI-HAT CONTROL
10: oKICK/!0
HH CON HI HAT KICK TOM1 CRASH TOM2 TOM3 RIDE
CRASH2
SNARE
[Locations of pad jacks]
NOTICE
6
1. Insert the power adaptor’s DC plug into the connector. Hook the power
adaptor’s cord around the cord clip to secure it in place.
2. Use the cable bands to bind the cables to the rack as shown on the right. ( )
3. Plug the AC power adaptor into an AC wall socket.
[Drum trigger module’s rear panel]
Cord clip
connector