User Manual

DTX900 Data List
21
Effect Parameter List
[2] NOISY
No. Parameter Range
1 Mod Depth 0 − 10
2 Mod Speed
0 − 127
3 Mod Feedback -63 − +63
4 Mod Mix Balance 1 − 127
5 Drive 0 − 127
6 AM Speed 0.0Hz − 39.7Hz
7 AM Depth 0 − 127
8 LPF Cutoff Frequency 1.0kHz − 20.0kHz
9 LPF Resonance 1.0 − 12.0
10 Dry/Wet Balance D63>W − D=W − D<W63
11 EQ Frequency 100Hz − 10.0kHz
12 EQ Gain -12dB − +12dB
13 EQ Width 1.0 − 12.0
14 —
15 —
16 —
[3] DIGITAL TURNTABLE
No. Parameter Range
1 Click Density 0 − 5
2 Click Level
0 − 127
3 Noise Tone 0 − 6
4 Noise Mod Speed 0.0Hz − 39.7Hz
5 Noise Mod Depth 0 − 127
6 Dry Send to Noise 0 − 127
7
Noise LPF Cutoff Frequency 1.0kHz − 20.0kHz
8 Noise LPF Q 1.0 − 12.0
9 Noise Level 0 − 127
10 —
11 Dry Level 0 − 127
12 Dry LPF Cutoff Frequency 1.0kHz − 20.0kHz
13 —
14 —
15 —
16 —
Category - TEC
[1] RING MODULATOR
No. Parameter Range
1 OSC Frequency Coarse 0.5Hz − 5.0kHz
2 OSC Frequency Fine
0 − 127
3 LFO Wave tri, sine
4 LFO Depth 0 − 127
5 LFO Speed 0.0Hz − 39.7Hz
6 HPF Cutoff Frequency 20Hz − 8.0kHz
7
LPF Cutoff Frequency 1.0kHz − 20.0kHz
8 —
9 —
10 Dry/Wet Balance D63>W − D=W − D<W63
11 —
12 —
13 − 16 : Same as the parameters shaded in gray in CROSS DELAY on page 15.
[2] DYNAMIC RING MODULATOR
No. Parameter Range
1 Sensitivity 0 − 127
2 HPF Cutoff Frequency
20 H z − 8.0kHz
3 LPF Cutoff Frequency 1.0kHz − 20.0kHz
4 Attack Time 0.3ms − 227ms
5 Release Time 2.6ms − 2171ms
6 Release Curve 0 − 127
7
Direction up, down
8 Dyna Threshold Level 0 − 127
9 Dyna Level Offset 0 − 127
10 Dry/Wet Balance D63>W − D=W − D<W63
11 ---
12 ---
13 − 16 : Same as the parameters shaded in gray in CROSS DELAY on page 15.
[3] DYNAMIC FILTER
No. Parameter Range
1 Filter Type LPF(12dB), LPF(18dB), LPF(24dB), HPF, BPF, BEF
2 Sensitivity
0 − 127
3 Dyna Level Offset 0 − 127
4 Resonance -16 − +111
5 Attack Time 0.3ms − 227ms
6 Release Time 2.6ms − 2171ms
7
Release Curve 0 − 127
8 Direction up, down
9 Dyna Threshold Level 0 − 127
10 Dry/Wet Balance D63>W − D=W − D<W63
11 —
12 —
13 − 16 : Same as the parameters shaded in gray in CROSS DELAY on page 15.
[4] AUTO SYNTH
No. Parameter Range
1 Mod Speed 0 − 127
2 Mod Wave Type
Ty p eA, TypeB, TypeC, TypeD
3 Mod Depth 0 − 127
4 Mod Depth Ofst R -63 − +63
5 HPF Cutoff Frequency 20Hz − 8.0kHz
6 LPF Cutoff Frequency 1.0kHz − 20.0kHz
7 Delay Time 0.1ms − 370.0ms
8 Delay Time Ofst R 0 − 884
9 Delay Level 0 − 127
10 Dry Mix Level 0 − 127
11 Feedback Level -63 − +63
12 FB Level Ofst R -63 − +63
13 AM Speed 0.0Hz − 39.7Hz
14 AM Wave tri, sine, saw up, saw down
15 AM Depth 0 − 127
16 AM Inverse R normal, inverse
[5] ISOLATOR
No. Parameter Range
1 On/off Switch off/on
2 Low Level
-6 4 − +63
3 Mid Level -64 − +63
4 High Level -64 − +63
5 Low Mute off/on
6 Mid Mute off/on
7 High Mute off/on
8 —
9 —
10 —
11 —
12 —
13 —
14 —
15 —
16 —
[6] SLICE
No. Parameter Range
1 Divide Type 16th − 4th
2 Gate Time
0 − 1 00%
3 Pan AEG Type A − E
4 Pan AEG Min Level 0 − 127
5 Pan Depth -63 − +63
6 Divide Min Level 0 − 127
7 Pan Type A − J
8 Drive 0 − 127
9 AEG Phase 0 − 15 (×16th note)
10 Dry/Wet Balance D63>W − D=W − D<W63
11 —
12 —
13 − 16 : Same as the parameters shaded in gray in CROSS DELAY on page 15.