Owner`s manual

Connection Status
This screen shows components connected using the
i.LINK interface, and the transfer capabilities
of each
component with respect to Dolby Digital, DTS and
MPEG audio formats.
Choices: Component
1, Component 2, ...
Initial setting: Component 1
Screen Sample
On-screen menu
AutoPlay Select
You can use this setting to specify a receiver for
automatically switching the input to this player when
you start playback
of a disc.
Choices: Off, Component
1, Component 2, ...
Initial setting: Off
Information about the operational status
of this unit is
displayed in the front panel display as follows:
Notes:
- If [PCM] is selectedfor Digital Output in Setup-
Audio Menu, all signals are converted to PCM
fonnat before being output.
-
An "*,, (asterisk) appears next to the name of the
component initially recognized by this unit. The
audio signal outputformat is determined by the
transfer capabilities
of the component, and signals
are output
to all connected components.
The component name is displayed only when the
i.LINK receiver component connected to this unit
supports i.LINK (AUDIO). The component name
is
not displayedfor DVD players or DV camcorders.
If the i.LINK component connected to this unit does
not contain any device name information, "****,,
is
displayed.
...... *RX-Z9
t7JLi.LINK
~ Connection Status
• Dolby D -+ Dolby D
• DTS -+DTS
• MPEG-+PCM
Display
Status
Displayed when data transfer is not possible
because you are already using the allowable
BUS FULL
maximum bandwidth
of the i.LINK bus or
when
17 or more i.LINK components are
connected to this unit.
LINKING
Displayed when this unit is checking a new
i.LINK connection.
Displayed when this unit and the i.LINK
LOOP CHECK
component are connected in a loop (where
the output signal is returned to the original
component).
Displayed when an i.LINK connection was
activated, but either the new connection is
NO OUTPUT
not recognized by DTCP, or the amplifier
connected to this unit does not allow
transmission.
Note:
- The i.LINK indicator located on the front panel
of
this unit lights only when i.LINKis selectedforanAV
amplifier connected to this unit via an i.LINK
inteiface. Even
if [Off] is selected for Audio Output
in the on-screen menu, the i.LINK indicator lights
whenever i.LINK
is selected on the connected AV
amplifier.
19
Connection Status
This screen shows components connected using the
i.LINK interface, and the transfer capabilities
of each
component with respect to Dolby Digital, DTS and
MPEG audio formats.
Choices: Component
1, Component 2, ...
Initial setting: Component 1
Screen Sample
On-screen menu
AutoPlay Select
You can use this setting to specify a receiver for
automatically switching the input to this player when
you start playback
of a disc.
Choices: Off, Component
1, Component 2, ...
Initial setting: Off
Information about the operational status
of this unit is
displayed in the front panel display as follows:
Notes:
- If [PCM] is selectedfor Digital Output in Setup-
Audio Menu, all signals are converted to PCM
fonnat before being output.
-
An "*,, (asterisk) appears next to the name of the
component initially recognized by this unit. The
audio signal outputformat is determined by the
transfer capabilities
of the component, and signals
are output
to all connected components.
The component name is displayed only when the
i.LINK receiver component connected to this unit
supports i.LINK (AUDIO). The component name
is
not displayedfor DVD players or DV camcorders.
If the i.LINK component connected to this unit does
not contain any device name information, "****,,
is
displayed.
...... *RX-Z9
t7JLi.LINK
~ Connection Status
• Dolby D -+ Dolby D
• DTS -+DTS
• MPEG-+PCM
Display
Status
Displayed when data transfer is not possible
because you are already using the allowable
BUS FULL
maximum bandwidth
of the i.LINK bus or
when
17 or more i.LINK components are
connected to this unit.
LINKING
Displayed when this unit is checking a new
i.LINK connection.
Displayed when this unit and the i.LINK
LOOP CHECK
component are connected in a loop (where
the output signal is returned to the original
component).
Displayed when an i.LINK connection was
activated, but either the new connection is
NO OUTPUT
not recognized by DTCP, or the amplifier
connected to this unit does not allow
transmission.
Note:
- The i.LINK indicator located on the front panel
of
this unit lights only when i.LINKis selectedforanAV
amplifier connected to this unit via an i.LINK
inteiface. Even
if [Off] is selected for Audio Output
in the on-screen menu, the i.LINK indicator lights
whenever i.LINK
is selected on the connected AV
amplifier.
19