SPECIAL MESSAGE SECTION PRODUCT SAFETY MARKINGS: Yamaha electronic products may have either labels similar to the graphics shown below or molded/stamped facsimiles of these graphics on the enclosure. The explanation of these graphics appears on this page. Please observe all cautions indicated on this page and those indicated on the safety instruction section.
SECTION DE MESSAGE SPÉCIAL INSCRIPTIONS DE SÉCURITÉ DU PRODUIT: Les produits électroniques Yamaha peuvent comporter des étiquettes semblables aux représentations graphiques indiquées ci-dessous ou fac-similés moulés/estampés de ces représentations graphiques sur l’encoffrement. L’explication de ces représentations graphiques apparaît à cette page. Veuillez respecter toutes les précautions indiquées à cette page et celles indiquées dans la section des directives de sécurité.
IMPORTANT SAFETY INSTRUCTIONS WARNING — When using any electrical or electronic product, basic precautions should always be followed. These precautions include, but are not limited to, the following: 1. 2. 3. 4. 5. 6. 7. Read these instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug.
INSTRUCTIONS DE SÉCURITÉ IMPORTANTES AVERTISSEMENT — Lors de l’utilisation de n’importe quel appareil électrique ou électronique, les précautions fondamentales devraient toujours être suivies. Ces précautions comprennent, mais ne sont pas limitées à, ce qui suit: placez ce produit ni aucun autre objet sur le cordon 17.
The control unit is classified as a Class 1 laser product. One of the labels below is located on the inside of the CD drive unit. L’unité de commande est classée produit laser de Classe 1. Une des étiquettes ci-dessous ou une étiquette similaire se trouve à l’intérieur du lecteur de CD. CLASS 1 LASER PRODUCT LASER KLASSE 1 1 ㉏▔ܝѻક CAUTION - CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO THE BEAM. VORSICHT - SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG KLASSE 3B, WHEN GEÖFFNET.
COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party Address Telephone Fax Type of Equipment Model Name : Yamaha Corporation of America : 6600 Orangethorpe Avenue, Buena Park, CA 90620 USA : 1-714-522-9011 : 1-714-522-9301 : Player Piano : DGB1KE3Classic This device complies with Part 15 of the FCC Rules.
Mounting the Control Unit to the Grand Piano Installation du boîtier de commande sur un piano à queue (1) (2) (3) Leave 5 mm of the shank (1) Remove the four screws from the sides of the control unit. (1) Retirer les quatre vis sur les côtés du boîtier de commande. (2) Place the metal suspension bracket, supplied with the Disklavier grand model, over the control unit, then secure the metal suspension bracket to the control unit using the four screws (4 10) supplied with the Disklavier.
(4) (5) (6) (4) Fit the “slots” of the metal suspension bracket containing the control unit to the screws mentioned in step (3). (4) Glisser les « fentes » du support métallique contenant le boîtier de commande sur les vis mentionnées à l’étape (3). (5) After mounting the control unit, push the control unit back as far as it will go and then tighten the three screws to secure the bracket.
Mounting an Optional USB Floppy Disk Drive to the Grand Piano Installation d’unité de disquette USB optionnelle sur le piano à queue (1) (2) Adhesive tape Ruban adhésif (3) USB cable Câble USB (1) Remove the backing papers from the adhesive tape inside the case, and fit the floppy disk drive into the case. (1) Enlevez les papiers arrière du ruban adhésif à l’intérieur du boîtier et insérez l’unité de disquette dans le boîtier.
English Classic Operation manual
Welcome to the Yamaha DisklavierTM! Thank you for purchasing the Yamaha Disklavier piano! The Disklavier is a fascinating instrument that integrates a classic Yamaha acoustic piano with innovative electronics to suit your entertainment, educational, and creative needs, while retaining the tone, touch and long-term value that have long made Yamaha pianos the world’s finest. English Before using your Disklavier piano, please read this manual thoroughly and retain it for future reference.
Important Precautions Read the following before operating the Disklavier. ■ Warnings ■ Cautions • Do not locate the Disklavier in a place subject to excessive heat, low temperatures, or direct sunlight. This could be a fire hazard and may damage the finish and internal parts. • Turn off all audio devices when connecting to the Disklavier. Refer to the user’s guide for each device. Use the correct cables and connect as specified. • Excessive humidity or dust can lead to fire or electric shock.
■ Interference • The Disklavier uses high-frequency digital circuits that may cause interference to radios and TVs placed close to it. If interference does occur, relocate the affected equipment. The remote control of this unit is powered by dry batteries. Improper use or misuse of the dry batteries can cause the dry batteries to heat up, leak electrolyte or burst which in turn may result in a fire, damage to equipment and/or nearby objects or in burns, injury or other bodily harm.
Table of Contents Quick Reference Playing Back Songs in a Different Key Learning about the Control Unit .............................1 (Transposition) .................................................... 31 Learning about Media ............................................1 Repeating Song Playback ................................... 32 Turning Your Disklavier On ....................................2 Repeating a Specific Section of a Song When You Finish...............................................
Hooking Up MIDI Devices ................................. 108 Managing Songs ..................................................72 Setting the Disklavier for MIDI Data Making Copies of Songs ......................................73 Reception .......................................................... 109 Deleting Songs.....................................................74 Setting the Disklavier for MIDI Data Renaming a Song ................................................75 Transmission .............
Quick Reference: Starting Quick Reference Learning about Media the Control Unit Learning about the Control Unit English Buttons that you will use for playback and recording. ON/OFF EJECT Turns on or shuts down the Disklavier. Opens the CD tray. PLAY/PAUSE ENTER (center) CURSOR Starts and pauses playback/recording. Executes the selection. Selects the item. SELECT STOP Opens the media selection screen. Stops playback/recording. RECORD Gets the Disklavier ready to record.
Quick Reference: Starting Turning Your Disklavier On Turning Your Disklavier On 1 Connect the Disklavier to mains. 2 Turn your Disklavier on. [ON/OFF] >> >> Your Disklavier is now ready for use! When You Finish … Shut your Disklavier down. [ON/OFF] When You Finish...
Quick Reference: Listening to a Song Listening to a CD included with the Disklavier Listening to a CD included with the Disklavier English 1 Load a CD. [EJECT] >> 2 Select “CD” as the playback source. [CURSOR] [SELECT] >> 3 >> CD tray on the Media Center [ENTER] >> Select an album. [CURSOR] [ENTER] >> 4 5 6 Select a song. [CURSOR] Start song playback. [PLAY] Stop song playback.
Quick Reference: Listening to a Song Listening to a Free DisklavierRadio Channel Listening to a Free DisklavierRadio™ Channel Before operating… Modem (without router function) Connect the Disklavier to a router or a modem equipped with a router that is connected to the Internet. Modem (with router function) Router Other device (such as computer) LAN cable Other device (such as computer) LAN cable Control unit (left side) Control unit (left side) For more details on connections, see page 98.
Chapter 1 Introduction Features English The Disklavier E3 Classic offers the valuable features that open up your musical possibility to explore. Here are brief explanations of such features: Advanced Features for Your Listening Pleasure • Special music CDs, contain over 17 hours of fantastic music, let you start listening on the day the Disklavier E3 Classic arrives at your home. • DisklavierRadio; you can listen to over 11 music channel by streaming broadcasts over the Internet.
Chapter 1 Introduction Names of Parts and Their Functions ■ Control Unit — Front Panel 4 1 2 3 5 6 7 8 9 [ON/OFF] button Turns on or shuts down the Disklavier. Press once to turn it on, and once again to shut it down. 1 10 11 Cursor/[ENTER] buttons Cursor: Used to select options and parameters. 10 Press this button inclining slightly upward/downward/left/ right. USB port Used to connect a USB flash memory, etc.
Chapter Introduction 1 ■ Control Unit — Rear Panel 1 2 3 4 5 6 English 7 8 9 10 11 USB TO DEVICE port Used to connect a USB flash memory, an optional USB floppy disk drive, etc. MIDI OUT terminal Used to connect external MIDI equipment for outputting MIDI data. 2 LAN port Used to connect to the Internet. 11 MIDI IN terminal Used to connect external MIDI equipment for inputting MIDI data. 1 10 OUTPUT jacks Used to connect the speaker cord from the monitor speaker.
Chapter 1 Introduction ■ Remote Control 1 13 2 14 15 16 3 17 4 18 5 19 20 6 21 7 22 8 9 23 24 10 25 26 11 12 27 1 [ON/STANDBY] button Turns on the Disklavier or puts it in the standby mode. 5 [RECORD] button ( page 49) Used to engage the record standby mode before recording starts. Number keypad Used for direct album/song selection and to enter a start time for song playback. [PLAY] button ( page 24) Used to start playback.
Chapter Introduction 9 [BACK] button Used to cancel the selection, and return to the previous screen. 1 20 [PAUSE] button ( page 25) Used to pause playback. [STOP] button ( page 25) Used to stop playback and recording. 21 [VOLUME] buttons ( page 30) Used to adjust the volume. [–] lowers the volume, [+] raises the volume. 10 [TRANSPOSE] buttons Used to transpose song playback. [–] transposes down, [+] transposes up, and [0] resets the transposition value to 00.
Chapter 1 Introduction ■ Monitor Speaker LOW 1 2 LINE 2 3 LOW/HIGH volume controls Adjust the base/treble sound volume. LINE1/2 volume controls Adjust the sound volume for each line input. Power indicator Lights up while the speaker is turned on. Note: For normal use, turn down the LINE2 volume completely, and turn up the LINE1 volume at the three o’clock position.
Chapter Introduction 1 Basic Disklavier Terminology The following is a list of several basic Disklavier words that you may need to know before proceeding with operational procedures in this manual. For additional Disklavier terminology, see the glossary provided in Chapter 15. PianoSoft·Plus Ensemble Song An ensemble song contains the same left- and right-hand parts as an L/R song, and extra tracks that are played by the internal XG tone generator.
Chapter 2 Getting Started Connecting the Control Unit Make sure that the cables extending from the piano is connected to the appropriate connectors or jacks on the rear panel of the control unit. Note: The cables should be connected to the control unit when the Disklavier is installed. If, however, it is not, carefully connect them to the appropriate connectors or jacks on the rear panel of the control unit. Note: Be sure to mount the control unit to the underside of the bass side key bed.
Chapter Getting Started 2 Using the Remote Control The Disklavier is equipped with a remote control which allows convenient control from almost anywhere in the room. This chapter provides notes on handling the remote control. English ■ Installing Batteries in the Remote Control Before the remote control can be used, the two batteries supplied with the Disklavier must be installed. Remove the battery cover from the rear of the remote control, install the batteries, and then replace the cover.
Chapter 2 Getting Started ■ Using the Remote Control To use the remote control, point it at the remote control sensor on the control unit. Approx. 5 m (16 ft.) 30˚ 30˚ 30˚ 30˚ Turning On the Disklavier 1 Make sure that the main switch on the power supply unit is turned on.
Chapter Getting Started 2 2 Press [ON/OFF] on the control unit. While the control unit is in the standby mode, you can also turn on the Disklavier by pressing [ON/STANDBY] on the remote control. See Chapter 2 “Getting Started – Turning Off the Disklavier (Standby Mode)” on page 18. English The following message appears on the display, and [ON/OFF] on the control unit lights green. After several seconds, the loading screen will appear, and last selected song will be loaded.
Chapter 2 Getting Started 2 Select “TimeZone” with the cursor buttons ([ [ ]), then press [ENTER]. ][ ][ ] !"#$%{ The time zone setup screen appears. 3 Press [+/YES] and [–/NO] to change the time zone. Examples of Time Zone The chart below shows the correspondence between the time zone setting on the Disklavier and actual time zone used in the U.S. and Canada.
Chapter Getting Started 2 ■ Calendar 1 Select “Clock Adj.” with the cursor buttons ([ [ ]), then press [ENTER]. ][ ][ ] English !"#$%{ The current date and time appear. 2 Press [ENTER]. The time setup screen appears with the cursor flashing on the hours display.
Chapter 2 Getting Started Turning Off the Disklavier (Standby Mode) Press [ON/STANDBY] on the remote control. The ending screen appears, and [ON/OFF] on the control unit lights red. Note: Press [ON/STANDBY] on the remote control to turn the Disklavier back on. See you again Shutting Down the Disklavier Press [ON/OFF] on the control unit. Note: Be sure to wait 5 seconds before turning the Disklavier back on. The ending screen appears, and [ON/OFF] on the control unit turns off.
Chapter Getting Started 2 Compatible File Format The Disklavier can handle these three types of file format: SMF0 Standard MIDI File format 0 for playback and recording. The name of the file should have an extension as “.MID” or “.mid.” English SMF1 Standard MIDI File format 1 for playback only. The name of the file should have an extension as “.MID” or “.mid.” E-SEQ Format developed by Yamaha, for playback only. The name of the file should have an extension as “.FIL” or “.fil.
Chapter 3 Basic Song Playback Types of Playable Software PianoSoft and PianoSoft·Plus When piano songs such as those contained in PianoSoft and PianoSoft·Plus software are played back on the Disklavier, the piano parts are actually played by the Disklavier keyboard, and the keys move up and down as though they were being played by an invisible performer. The ensemble parts (contained in PianoSoft·Plus software) are played by the internal tone generator and are heard from the monitor speaker.
Chapter Basic Song Playback 3 Selecting Medium and Their Contents [SELECT] 1 Insert a desired medium. English CD CD eject button USB flash memory USB port 2 Press [SELECT]. The media selection screen appears with the current selected medium highlighted. =MEDIA SELECT= or Control unit 3 Remote control Memory CD Select a desired medium with the cursor buttons ([ [ ]).
Chapter 3 Basic Song Playback 4 Press [ENTER] or [ ]. The album selection screen appears. =ALBUM SELECT= or 5 01:50 Greats for t Select a desired album with the cursor buttons ([ ][ ]). ?=] =ALBUM SELECT= Note: You can also select albums directly using the number keypad on the remote control. See Chapter 3 “Basic Song Playback – Using the Number Keypad” on page 24.
Chapter Basic Song Playback 3 ■ Song Playback Screen Here are a few things that you will often see during playback. 1 2 3 4 5 6 English 7 1 Media The selected medium is displayed here. Album/Song Number The number of the selected album and song is displayed here.
Chapter 3 Basic Song Playback Using the Number Keypad Album or song selection screen Number button You can also select albums or songs directly with the number keypad on the remote control. Press the corresponding number button, then press [ENTER]. For example, to select album number 5, first press [0], then [5], then [ENTER]. =ALBUM SELECT= 0-9/ENT 05: To select song number 36, first press [0], then [3], then [6], then [ENTER].
Chapter Basic Song Playback 3 Stopping Playback During playback [STOP] Press [STOP]. or Remote control English Control unit Playback stops, and the song returns to the beginning. [PLAY/PAUSE] on the control unit turns off, and the counter is reset to “00:00” or “001-1.” Pausing Playback During playback 1 [PAUSE] Press [PLAY/PAUSE] on the control unit, or [PAUSE] on the remote control. or Control unit Remote control Playback pauses.
Chapter 3 Basic Song Playback Fast Preview & Review During playback [FORWARD] or [REVERSE] During playback, fast preview and review allow you to quickly search through a song while listening to the sound. This is useful for locating a desired position within a song. ■ Fast Preview 1 To preview, hold [ ] on the control unit or press [FORWARD] on the remote control.
Chapter Basic Song Playback 3 Fast Forward & Reverse Stop or pause mode [FORWARD] or [REVERSE] In the stop or pause mode, fast forward and reverse allow you to quickly locate a desired position in a song. English Reverse can also be used to return a song to the beginning, ready to play again. ■ Fast Forward 1 In the stop or pause mode, hold [ ] on the control unit or press [FORWARD] on the remote control.
Chapter 3 Basic Song Playback Searching a Specific Section of a Song During playback or stop/pause mode [SEARCH] Playback can be started from a specified point in a song. Instead of using fast forward or preview, you can use this function to go directly to a desired point within a song. If the current song uses the minutes and seconds time format, you specify the point in minutes and seconds. If it uses the measures and beats time format, you specify the point in measures and beats.
Chapter Basic Song Playback 3 Listening to the DisklavierRadio Media selection screen “D-Radio” You can listen to streaming broadcasts of music, with many channels of music contents. Select “D-Radio” in the media selection screen. The channel selection screen appears. =RADIO SELECT= To select a medium, see Chapter 3 “Basic Song Playback – Selecting Medium and Their Contents” on page 21. 01:Complimentary C 2 Press [ ] or [ ] or [+/YES] or [–/NO] to select a channel.
Chapter 3 Basic Song Playback ■ Muting the Sound 1 Press [PAUSE] or [STOP]. “MUTE” appears on the upper right of the screen. =D-Radio= CH-08: Jazz My Funny Val or 2 MUTE Note: Streaming broadcasts continue during muting. Therefore, the song broadcasted when releasing muting may differ from the one when muting. Press [PAUSE] or [STOP] again to release muting.
Chapter 4 Advanced Song Playback Changing the Playback Tempo [TEMPO –] or [TEMPO +] Note: You cannot change the playback tempo of songs on audio CDs. These tempo settings remain in effect until recording is started, another medium or album is selected, or the Disklavier is turned off. 1 Press [TEMPO –] or [TEMPO +] on the remote control. English You can speed up or slow down the playback tempo. Slowing down the playback tempo can be useful when practicing a difficult piano part.
Chapter 4 Advanced Song Playback 1 Press [TRANSPOSE –] or [TRANSPOSE +] on the remote control. The transposition setting screen appears. =Memory= TRANS-/0/+ TRANS +01key 2 Press [TRANSPOSE –] or [TRANSPOSE +] to change the key. Playback can be transposed in half-step increments up or down two octaves (–24 key to +24 key) Press [TRANSPOSE 0] to set to the original key. Repeating Song Playback [REPEAT] There are three repeat modes (ALL, RPT, RND) as described below.
Chapter Advanced Song Playback 3 Press [PLAY] to start repeat playback. 4 To cancel the repeat mode, press [REPEAT] until “OFF” appears on the screen. 4 English Repeating a Specific Section of a Song (A-B Repeat) During playback [A-B] In the A-B repeat, playback is repeated between two specified points in a song: point A and point B. This function is useful when practicing or memorizing a difficult section of a song.
Chapter 4 Advanced Song Playback 3 To cancel the A-B repeat, press [A-B] so that “OFF” flashes on the screen. =Memory= A-B Note: The A-B repeat is cancelled if you escape from the A-B repeat setting screen by other operations. Flashes Pressing [BACK] also cancels the point setting, and returns to the song playback screen.
Chapter Advanced Song Playback 4 ■ Cancelling the Pedal Part 1 On the part cancellation screen, press [ =Piano Part= ] to select “P=.” L/R L=ON R=OFF P=ON English 2 Press [–/NO] to cancel a pedal part. =Piano Part= L/R L=ON R=OFF P=OFF 3 To replay the pedal part, press [+/YES] with the cursor is on “P=.” 4 Press [BACK] to return to the song playback screen.
Chapter 4 Advanced Song Playback ■ Adjusting the TG Balance 1 Press [BALANCE] on the remote control. The TG balance setting screen appears. =BALANCE= TG BALANCE 100 2 -/+ Press [+/YES] and [–/NO] to adjust the volume of the tone generator. Note: You can also use the dial on the control unit to adjust the volume. Tone generator volume can be adjusted in a range of 10 to 127. ■ Adjusting the Audio Balance 1 Press [BALANCE] twice on the remote control. The audio balance setting screen appears.
Chapter Advanced Song Playback 4 ■ Adjusting the Voice Balance 1 Press [BALANCE] three times on the remote control. The voice balance setting screen appears. =BALANCE= Press [+/YES] and [–/NO] to adjust the volume of the voice. English 2 -/+ VOICE BALANCE 100 ×3 Note: You can also use the dial on the control unit to adjust the volume. Voice volume can be adjusted in a range of 0 to 127. Adjusting the Pitch of Audio During playback [FUNC.
Chapter 4 Advanced Song Playback Adjusting the L/R Balance of Audio During playback [FUNC.] You can temporarily adjust the L/R balance of an audio CD. Balance adjustments are effective until another song is selected, recording is started, or the Disklavier is turned off. 1 During the song playback, press [FUNC.] several times. The audio pan setting screen appears. =CD= -+ENT AudioPan=Center 2 Press [+/YES] and [–/NO] to change the audio pan.
Chapter Advanced Song Playback 4 Using the Timer Play [SETUP] “TimerPlay” You can program your Disklavier to start or stop playback of a song at various specified times. All you need to do is register up to a maximum of 99 timer settings, and your Disklavier will perform them unattended. This function is called “timer play.” 1 Note: The control unit must be turned on in advance in order for the timer play to function. The timer play cannot turn on/off the control unit.
Chapter 4 Advanced Song Playback 4 Press [ ] and [ ] to select the desired program number. The cursor moves to the function parameter. 5 Press [ ] and [ ] to move the cursor to the function parameter, then press [+/YES] and [–/NO] to select the desired function. =TimerPlay= -+ >TimerPlay=ON 01[### ##:## PLAY -----] The following functions are available: PLAY Starts playback of songs. STOP Stops playback of songs. RND Starts playback of songs at random.
Chapter Advanced Song Playback 7 4 Press [ ] to move the cursor to the day parameter, then press [+/YES] and [–/NO] to select the desired day. =TimerPlay= _?=]-+ >TimerPlay=ON 01[M-F ##:## PLAY Mem01] 8 ALL The timer play functions on every day of the week. MON The timer play functions only on Monday. TUE The timer play functions only on Tuesday. WED The timer play functions only on Wednesday. THU The timer play functions only on Thursday. FRI The timer play functions only on Friday.
Chapter 4 Advanced Song Playback ■ About Song Playback Screen When the song playback is stopped — with the timer play function is set to ON and the current time is displayed — “T” flashes to the right side of the current time. Indicates that the timer play is on.
Chapter Advanced Song Playback 4 Press [ENTER] to return to the setup menu screen. English Video Synchronized Playback You can enjoy piano playback with the video recorded on the DVD recorder. 1 Perform the video synchronized recording in advance. 2 Make sure that the OMNI IN setting is set to “AutoDetect”. 3 Turn down the volume completely on the TV if you connect the audio output of the DVD recorder to the TV. Turn down the volume completely on the camcorder if you use the camcorder only.
Chapter 4 Advanced Song Playback Adding Disklavier Accompaniment to Commercial CD Songs (PianoSmart™ Playback) Insert a CD Select a SmartPianoSoft song [PLAY] You can add a Disklavier piano performance you recorded or on commercially available SmartPianoSoft software to the playback of songs on your favorite CDs. 1 Insert a desired CD that you want to synchronize with the SmartPianoSoft song. 2 Select a desired SmartPianoSoft song. 3 Press [PLAY].
Chapter Advanced Song Playback 2 4 Press [PLAY]. Playback stops, and the key to play next moves slightly. English Key moves slightly The key to play flashes in the counter. Pachelbel=s Flashes 3 Play the key that the keyboard indicates. This will continue until the song is finished. Notice that the Disklavier patiently waits for you to play the right key before proceeding to the next key.
Chapter 5 Advanced Piano Playing Playing the Disklavier along with the Internal Metronome [METRONOME] The internal metronome helps you playing along the meter (beat) and the tempo you set. Also the volume of the metronome can be adjusted. 1 Press [METRONOME] on the remote control. The metronome setting screen appears and the metronome starts to click.
Chapter Advanced Piano Playing 4 To change the volume, move the cursor to the volume parameter (“VOLUME”) with the cursor buttons ([ ] [ [ ] [ ]), then press [+/YES] and [–/NO]. 5 ] =METRONOME= _?=]-+ TEMPO=125bpm =3/4 VOLUME= SOUND=BUZZER English The volume can be adjusted in 4 steps. 5 To change the sound, move the cursor to the sound parameter (“SOUND”) with the cursor buttons ([ ] [ [ ] [ ]), then press [+/YES] and [–/NO].
Chapter 5 Advanced Piano Playing 2 Press [+/YES] and [–/NO] to select a voice group. Changing the voice group displays the top voice of that group in the voice parameters. ][ 3 To change the voice, press [ ] to move the cursor to the voice parameter (“Voice”), then press [+/YES] and [–/NO]. ][!" If necessary, adjust the volume of the voice in the voice balance setting screen.
Chapter 6 Basic Recording A song that you play on the Disklavier can be recorded and the recorded song can be easily saved for the selected medium. Furthermore, you can title your new recording for simple distinguish before recording. Recording a New Song [RECORD] 1 Select a destination medium and album. 2 Press [RECORD]. The recording standby screen appears, and [RECORD] on the control unit lights red and [PLAY/PAUSE] flashes in green.
Chapter 6 Basic Recording Titling a Song at the Start of Recording [RECORD] [FUNC.]×2 Title a new song before you start recording. 1 Select a destination medium and album. 2 Press [RECORD]. 3 Press [FUNC.] twice in the recording standby screen. To rename the existing song, see Chapter 8 “Media Management – Renaming a Song” on page 75. =Memory= [A-Z] ×2 Enter a title to a new song. =Memory= Chopin [a-z] You can enter up to 64 characters.
Chapter Basic Recording 6 ■ Entering Characters How to Enter Characters with the Remote Control The following illustration shows how to enter characters with the remote control. English Number keypad Overwrites a number. [SEARCH] button Overwrites a dot (.). [REVERSE] button Deletes a character. The characters on the right of the deleted one move to the left for one character space. [FORWARD] button Inserts a space. [ ]/[ ] buttons Moves the cursor left and right.
Chapter 7 Advanced Recording This chapter describes further functions for the advanced piano recording such as playing and measuring the current playing song tempo with the metronome, recording the left-hand part and the right-hand part separately. Recording with the Internal Metronome [METRONOME] [RECORD] You can use the metronome to record songs. Songs recorded with the metronome will be in the measures and beats format. All metronome parameters are reset when the Disklavier is switched off.
Chapter Advanced Recording 4 To change the volume, move the cursor to the volume parameter (“VOLUME”) with the cursor buttons ([ ] [ [ ] [ ]), then press [+/YES] and [–/NO]. 7 ] =METRONOME= _?=]-+ TEMPO=125bpm =3/4 VOLUME= SOUND=BUZZER English The volume can be adjusted in 4 steps. 5 To change the sound, move the cursor to the sound parameter (“SOUND”) with the cursor buttons ([ ] [ [ ] [ ]), then press [+/YES] and [–/NO].
Chapter 7 Advanced Recording Recording the Left and Right Parts Separately [RECORD] [FUNC.] When recording an L/R song, the left- and right-hand parts can be recorded separately. Either part can be recorded first, and the pedals can be recorded with the first part. While you record the second part, the first part will play back for monitoring.
Chapter Advanced Recording Press [RECORD]. 8 Press [ ] and [ ] to select the L/R song with the lefthand part that you have just recorded, then press [ENTER]. 9 Press [FUNC.] in the recording standby screen. English 7 7 The part selection screen appears. =Memory= L=PLY R=OFF LR The part that has already been recorded is displayed as “L=PLY.” 10 Press [PART SELECT R] to record the right-hand part. =Memory= L=PLY R=REC LR The part set to “REC” will be recorded. 11 Press [PLAY].
Chapter 7 Advanced Recording 12 Press [STOP] when you finish playing your song. The following screen appears. =Memory= ENT Save to Disk? *SAVE *NEW *CANCEL The following table gives a description of each of the options. Option Description SAVE The second part is saved with the first part under the current song number, overwriting the previously saved first part. NEW The second part is saved under a new song number. The first part is kept under the previous song number.
Chapter Advanced Recording 4 7 Press [PART SELECT R] to set both parts to record. The split point setting screen appears. =Memory= -+ LR=REC SPLIT=C3 English The above display shows that the default keyboard split point is note C3, or middle C. In this case, note C3 and notes below are saved as the left-hand part and notes above C3 are saved as the right-hand part, as shown in the following figure.
Chapter 7 Advanced Recording Re-Recording One Part [RECORD] Select the L/R song [PART SELECT L] or [PART SELECT R] You can re-record the only one part left-hand or the right-hand of the existing L/R song. 1 Select a desired medium and album. 2 Press [RECORD]. 3 Press [ ] and [ ] to select the L/R song that you want to re-record, then press [ENTER]. 4 Press [PART SELECT L] or [PART SELECT R] to select the part to re-record. The part set to “REC” will be re-recorded. 5 Press [PLAY].
Chapter Advanced Recording 7 The following table gives a description of each of the options. Description SAVE The re-recorded part is saved with the other existing part under the current song number, overwriting the selected part. NEW The re-recorded part is saved under a new song number. The existing parts are kept under the current song number. English Option CANCEL The re-recorded part is discarded. The existing parts are kept under the current song number. 7 Press [ ] and [ [ENTER].
Chapter 7 Advanced Recording 3 Press [ ] and [ ] to select the song in which you want to change the tempo, then press [ENTER]. 4 Press [FUNC.] three times. ×3 For measures and beats, the current song tempo (bpm) is shown. =Memory= -+ TEMPO=117bpm =4/4 VOLUME= SOUND=BUZZER For minutes and seconds, the current song tempo is shown as “000%.” =Memory= TEMPO=+000% 5 -+ Press [+/YES] and [–/NO] to change the tempo. [+/YES] increases the tempo, and [–/NO] decreases the tempo.
Chapter Advanced Recording 7 Press [ ] and [ 7 ] to select an option, then press [ENTER]. English To change the tempo again or to reset the original tempo, repeat steps 1 to 6. Video Synchronized Recording [SETUP] “AudioI/O” Connect a camcorder and a DVD recorder By recording a song played on the Disklavier synchronized with the video recording, later on, you can enjoy piano playback with the video.
Chapter 7 Advanced Recording 3 Select “OMNI IN” with the cursor buttons ([ ] [ ]), then press [+/YES] and [–/NO] to change setting to “Auto Detect”. ] 4 Select “OMNI OUT” with the cursor buttons ([ ] [ then press [+/YES] and [–/NO] to change setting to “SYNC”. ]), ][ 5 Press [ENTER] to complete the operation. 6 Connect a camcorder and a DVD recorder to the control unit.
Chapter Advanced Recording 7 ■ Starting Video Synchronized Recording 1 Select a destination medium and album. 2 Press [RECORD]. To select a medium and album, see Chapter 3 “Basic Song Playback – Selecting Medium and Their Contents” on page 21. English The video synchronized recording standby screen appears, and [RECORD] on the control unit lights red, and [PLAY/PAUSE] flashed in green. =Memory=(SYNC) SO LR 99% A01-005 <00:00> (New Song) 3 Set the camcorder to video shooting mode.
Chapter 7 Advanced Recording ■ Using the Camcorder only If your camcorder has both mic input and audio output, you can perform video synchronized recording using the camcorder only. 1. Set the Disklavier following the procedures 1 to 5 on page 61. 2. Connect a camcorder to the control unit. Camcorder To mic/line input RCA cord with resistance (not supplied) To audio output RCA cord (not supplied) Control unit 3. Select a destination medium and album. 4. Press [RECORD]. 5.
Chapter Advanced Recording 7 CD Synchronized Recording Insert an audio CD [RECORD] You can record a Disklavier piano performance along with the playback of songs on commercial CDs. Select a destination medium and album, then song in the selected album. 2 Insert an audio CD and select the song that you want to synchronize with. 3 Press [RECORD]. Note: The Disklavier recognizes the destination album by selecting the song in it. Note that the selected song is not overwritten by this procedure.
Chapter 8 Media Management This chapter describes how to manage contents inside the media, such as managing albums, songs and playlists. Managing Albums Album selection screen [FUNC.] You can use the album function menu for creating, deleting and copying albums inside a medium. 1 Press [FUNC.] in the album selection screen. To select a album, see Chapter 3 “Basic Song Playback – Selecting Medium and Their Contents” on page 21. The album function menu screen appears.
Chapter Media Management 1 8 Select “CopyAlbum” in the album function menu, then press [ENTER]. (1/2) =ALBUM MENU= *CopyAlbum *DeleteAlbum *NewAlbum *RenameAlbum The CopyAlbum screen appears. 2 English ! { Select a destination medium with [+/YES] and [–/NO]. ! { 3a To copy to the new album, press [ENTER]. “OK?” flashes in the first line of the screen.
Chapter 8 Media Management 4 Press [+/YES] to make a copy, [–/NO] to cancel. =CopyAlbum= Executing... =CopyAlbum= Completed. Press any button. ANY After a while, the completion message appears. Press any button to return to the album selection screen. Deleting Albums Album selection screen [FUNC.] “DeleteAlbum” You can delete the albums. This function is available for albums on [Memory], [USB1], [USB2] and [FromToPC]. 1 Select “DeleteAlbum” in the album function menu, then press [ENTER].
Chapter Media Management 8 Creating a New Album Album selection screen [FUNC.] “NewAlbum” You can create a new album into the selected medium. This function is available for albums on [Memory], [USB1] and [USB2]. Select the “NewAlbum” in the album function menu, then press [ENTER]. Note: If you enter the same title as the album already exists, the new album is titled in the form of “album title xx” (“xx” indicates the number). English 1 Note: Up to 99 albums can be created in a medium.
Chapter 8 Media Management 5 Press [+/YES] to create a new album, [–/NO] to cancel. =NewAlbum= Executing... =NewAlbum= Completed. Press any button. ANY After a while, the completion message appears. Press any button to return to the album selection screen. Renaming an Album Album selection screen [FUNC.] “RenameAlbum” You can rename the albums which already named. This function is available only for albums on [Memory]. 1 Select “RenameAlbum” in the album function menu, then press [ENTER].
Chapter Media Management 4 8 Press [ENTER]. “OK?” flashes in the first line of the screen. English 5 Press [+/YES] to rename, [–/NO] to cancel. =RenameAlbum= Executing... =RenameAlbum= Completed. Press any button. ANY After a while, the completion message appears. Press any button to return the album selection screen. Rearranging the Order of Albums Album selection screen [FUNC.] “SortAlbum” You can rearrange the order of albums that you selected.
Chapter 8 Media Management 3 Press [ENTER]. “OK?” flashes in the first line of the screen. =SortAlbum= OK? YES/NO 08:Mike Garson Trio-Live 06:Favorite Latin Select 4 Press [+/YES] to rearrange, [–/NO] to cancel. =SortAlbum= Executing... =SortAlbum= Completed. Press any button. ANY After a while, the completion message appears. Press any button to return to the album selection screen. Managing Songs Song selection screen [FUNC.
Chapter Media Management 8 Making Copies of Songs Song selection screen [FUNC.] “CopySong” You can copy songs stored on an album to another. This function is available for song in the album on [Memory], [CD](CDROM), [USB1], [USB2] and [FromToPC]. Select “CopySong” in the song function menu, then press [ENTER]. Note: Up to 999 songs can be saved in an album. English 1 Note: Copy-protected songs, such as PianoSoft songs, cannot be copied to a removable medium.
Chapter 8 Media Management 5 Press [+/YES] to make a copy, [–/NO] to cancel. =CopySong= Executing... =CopySong= Completed. Press any button. ANY After a while, the completion message appears. Press any button to return to the song selection screen. Deleting Songs Song selection screen [FUNC.] “DeleteSong” You can delete songs stored on an album. This function is available for songs in the album on [Memory], [USB1], [USB2], [Playlist] and [FromToPC].
Chapter Media Management 8 Renaming a Song Song selection screen [FUNC.] “RenameSong” You can rename the songs which already named. This function is available for songs in the album on [Memory], [USB1], [USB2] and [FromToPC]. Select “RenameSong” in the song function menu, then press [ENTER]. English 1 (1/2) =SONG MENU= *CopySong *DeleteSong *RenameSong *SortSong The RenameSong screen appears. ENT =RenameSong= 006:Toccata 2 Press [ENTER]. The song title editing screen appears.
Chapter 8 Media Management 5 Press [+/YES] to rename, [–/NO] to cancel. =RenameSong= Executing... =RenameSong= Completed. Press any button. ANY After a while, the completion message appears. Press any button to return to the song selection screen. Rearranging the Order of Songs Song selection screen [FUNC.] “SortSong” You can rearrange the order of songs in an album. This function is available only for songs in the album on [Memory] and [Playlist].
Chapter Media Management 3 8 Press [ENTER]. “OK?” flashes in the first line of the screen. =SortSong= OK? YES/NO 008:Interaction 006:Toccata and Fugue English 4 Press [+/YES] to rearrange, [–/NO] to cancel. =SortSong= Executing... =SortSong= Completed. Press any button. ANY After a while, the completion message appears. Press any button to return to the song selection screen. Converting Song Format Song selection screen [FUNC.] “ConvertSong” The song format can be converted to other format.
Chapter 8 Media Management 2 Press [+/YES] and [–/NO] to select a song format. -+ENT =ConvertSong= 001:Song For Students SMF0 Piano1 This following options are available: 3 Option Song Format E-SEQ E-SEQ format SMF0 SMF (Standard MIDI File) format 0 SMF1 SMF (Standard MIDI File) format 1 Piano1 E-SEQ format to play on all Disklavier in correct tempo Press [ENTER]. “OK?” flashes in the first line of the screen.
Chapter Media Management 1 8 Select “Counter” in the song function menu, then press [ENTER]. } The CounterChange screen appears. English ENT =CounterChange= 001:Song For Students TIME METRONOME TIME: minutes and seconds display METRONOME: measures and beats display 2 Press [ENTER]. “OK?” flashes in the first line of the screen. =CounterChange=OK?YES/NO 001:Song For Students TIME METRONOME 3 Press [+/YES] to change, [–/NO] to cancel.
Chapter 8 Media Management 1 Select “Strip XP” in the song function menu, then press [ENTER]. } The Strip XP screen appears. 2 Press [ENTER]. “OK?” flashes in the first line of the screen. 3 Press [+/YES] to execute, [–/NO] to cancel. After a while, the completion message appears. Press any button to return to the song selection screen.
Chapter Media Management 8 Adding Songs/Albums to the Playlist Media selection screen “Memory” Album or song selection screen [FUNC.] “AddToPList” This function is available only for songs/albums on [Memory]. Select “AddToPList” in the album or song function menu, then press [ENTER]. } Note: You cannot add songs on media other than [Memory] directly to the playlist. First copy songs to the internal flash memory.
Chapter 8 Media Management Deleting a Playlist Media selection screen “Playlist” Album selection screen [FUNC.] “DeleteList” You can delete the playlists which already registered. 1 Select “DeleteList” in the album function menu for the playlist, then press [ENTER]. (1/1) =ALBUM MENU= *DeleteList *NewList *RenameList The DeleteList screen appears. ENT =DeleteList= 02:My Best Collection 2 Press [ENTER]. “OK?” flashes in the first line of the screen.
Chapter Media Management 8 Creating a New Playlist Media selection screen “Playlist” Album selection screen [FUNC.] “NewList” You can create a new playlist for playing back your favorite songs in your selected order. Select “NewList” in the album function menu for the playlist, then press [ENTER].
Chapter 8 Media Management 5 Press [+/YES] to create a new playlist, [–/NO] to cancel. =NewList= Executing... =NewList= Completed. Press any button. ANY After a while, the completion message appears. Press any button to return to the album selection screen for the playlist. Renaming a Playlist Media selection screen “Playlist” Album selection screen [FUNC.] “RenameList” You can rename a playlist which already registered.
Chapter Media Management 4 8 Press [ENTER]. “OK?” flashes in the first line of the screen. =RenameList= OK? YES/NO My Best Hit Collection English 5 Press [+/YES] to rename, [–/NO] to cancel. =RenameList= Executing... =RenameList= Completed. Press any button. ANY After a while, the completion message appears. Press any button to return to the album selection screen for the playlist. Managing Media Media selection screen [FUNC.
Chapter 8 Media Management Making Copies of the Entire Contents in a Medium Media selection screen [FUNC.] “CopyAll” You can copy the entire contents in a medium to the another medium. The function is available for [Memory], [CD](CD-ROM), [USB1], [USB2] and [FromToPC]. To select a medium, see Chapter 3 “Basic Song Playback – Selecting Medium and Their Contents” on page 21. 1 Select “CopyAll” in the media function menu, then press [ENTER].
Chapter Media Management 8 Deleting the Entire Contents in a Medium Media selection screen [FUNC.] “DeleteAll” You can delete the entire contents in a medium. This function is available for [Memory], [USB1], [USB2] and [FromToPC]. Select “DeleteAll” in the media function menu, then press [ENTER]. English 1 To select a medium, see Chapter 3 “Basic Song Playback – Selecting Medium and Their Contents” on page 21. =MEDIA MENU= *CopyAll *DeleteAll The DeleteAll screen appears.
Chapter 8 Media Management Copying Song File from a Personal Computer to the Disklavier You can copy song files from a Windows or Macintosh computer to a special folder on the Disklavier called [FromToPC] and then play them on the Disklavier. 1 Connect the control unit to a LAN (local area network) to which a personal computer with a song file is also connected.
Chapter Media Management 8 ■ For Windows 2 On the computer screen, click [Start] and then select [My Network Places]. Note: [Dkv******] differs depending on each Disklavier. The [My Network Places] window appears. Confirm that the [Dkv******] icon is shown in the [My Network Places] window. Double-click the [Dkv*******] icon. The [Dkv*******] folder opens. Confirm that the [FromToPC] icon is shown in the [Dkv******] folder.
Chapter 8 Media Management ■ For Mac OS X 10.3 or 10.4 2 Click the [Finder] icon in the dock, and then click the [Network] icon in the left side of the window. The [Network] window appears. Confirm that the [Dkv] icon is shown in the [Network] window. 3 Click the [Dkv] icon. Note: [Dkv******] differs depending on each Disklavier. The [Dkv] folder opens. Confirm that the [Dkv******] icon is shown in the [Dkv] folder. 4 Click the [Dkv******] icon.
Chapter Media Management 8 ■ For Mac OS X 10.5 or 10.6 2 Click the [Finder] icon in the dock, and then select [Go] and then [Network] from the menu bar. Note: [Dkv******] differs depending on each Disklavier. The [Network] window appears. Confirm that the [Dkv******] icon is shown in the [Network] window. Click the [Dkv*******] icon. The [Dkv*******] folder opens. Confirm that the [FromToPC] icon is shown in the [Dkv******] folder.
Chapter 8 Media Management Refreshing the Contents in [FromToPC] Media selection screen “FromToPC” [FUNC.] “Refresh” You must refresh the contents in the [FromToPC] folder after copying song files from a personal computer, in order to play them on the Disklavier. 1 Select “Refresh” in the media function menu, then press [ENTER]. The Refresh screen appears. ENT =Refresh= Media=FromToPC 2 Press [ENTER]. “OK?” flashes in the first line of the screen.
Chapter Media Management 8 Formatting the Floppy Disk (Optional) Select the floppy disk [FUNC.] “Format” In the case of using the unformatted floppy disk on the floppy drive (optional) or deleting the entire contents on the floppy disk, format the floppy disk. Connect the floppy drive (optional) to the USB port on the control unit. 2 Insert a floppy disk to the floppy drive. 3 Select “Format” in the media function menu, then press [ENTER].
Chapter 8 Media Management ■ Floppy Disk Accidental Erasure Protection Floppy disks have an erasure protection tab located on the reverse side of the disk in the bottom right-hand corner. When formatting a disk, make sure that its erasure protection tab is set to “unprotected.” Protected When the tab window is open, formatting and recording are not possible. Unprotected When the tab window is closed, formatting and recording are possible.
Chapter Media Management 3 Select “Backup” with the cursor buttons ([ [ ]), then press [ENTER]. ][ ][ 8 ] !"#$%{ English The Backup screen appears. 4 Press [ENTER]. “OK?” flashes in the first line of the screen. =Backup= OK? YES/NO Backup song data? 5 Press [+/YES] to make a backup, [–/NO] to cancel. = =Backup= Completed. Press any button.
Chapter 8 Media Management 3 Select “Restore” with the cursor buttons ([ [ ]), then press [ENTER]. ][ ][ ] !"#$%{ The Restore screen appears. 4 Press [ENTER]. “OK?” flashes in the first line of the screen. =Restore= OK? YES/NO Restore this data? Date:2007-10-22 15:42:00 5 Press [+/YES] to restore, [–/NO] to cancel. = =Restore= Completed. Press any button.
Chapter 9 Internet Direct Connection (IDC) By connecting to the Internet, you can enjoy a streaming broadcast or download update programs directly. What is Internet Direct Connection (IDC)? English Internet Direct Connection (IDC) is a feature that allows you to connect your Disklavier directly to the Internet. Internet Direct Connection users are able to listen to a streaming broadcast (DisklavierRadio), and receive valuable information such as product updates.
Chapter 9 Internet Direct Connection (IDC) ■ Connecting the Control Unit to the Internet Connection example 1: Using a modem with router function Modem (with router function) Other device (such as computer) LAN cable Note: Some types of modems (such as ADSL modems or cable modems) have multiple ports for connecting two or more devices (such as computer, musical instrument, etc.).
Chapter Internet Direct Connection (IDC) 9 For further information on the Internet connection (only a wired LAN connection is supported), visit the Yamaha Disklavier website: http://services.music.yamaha.com/radio/ ■ Notes on Network Security English The Disklavier E3 Classic attempts to achieve a balance between security and usability in its network implementation.
Chapter 9 Internet Direct Connection (IDC) 1 Press [INTERNET] on the remote control. The Internet menu screen appears. (1/1) =Internet= *D-Radio *MyAccount *Update 2 Select a desired menu with the cursor buttons ([ [ ] [ ]), then press [ENTER]. ][ ] Perform operations on the screen that appears. Checking Your Account Information [INTERNET] “MyAccount” You can confirm your current account information of IDC service. You can also log out from the IDC service.
Chapter Internet Direct Connection (IDC) 2 Select “MyAccount” with the cursor buttons ([ [ ] [ ]), then press [ENTER]. ][ 9 ] (1/1) =Internet= *D-Radio *MyAccount *Update English The MyAccount screen appears. ] 3 Select a desired option with the cursor buttons ([ then press [ENTER]. ][ ]), Perform operations on the screen that appears.
Chapter 9 Internet Direct Connection (IDC) 2 Select “Update” with the cursor buttons ([ [ ]), then press [ENTER]. ][ ][ ] (1/1) =Internet= *D-Radio *MyAccount *Update The update screen appears if there is any update program available. ] You can scroll the screen up or down with the cursor buttons ([ [ ]). 3 ] Following the instructions on the screen, select the option with the cursor buttons ([ ] [ ] [ ] [ ]), then press [ENTER].
Chapter Internet Direct Connection (IDC) 9 Setting the Disklavier for the Internet Connection [SETUP] “Network” You can change various settings related to the Internet connection. In most cases, you do not have to change the default factory settings. Information To use the Internet connection, inquire of your Internet service provider. Use DHCP Select the method to determine several addresses. If your router has DHCP server function, we recommend that you to select “DHCP” or “DHCP+DNS.
Chapter 9 Internet Direct Connection (IDC) 3 Select a desired option with the cursor buttons ([ ] [ [ ] [ ]), then press [+/YES] and [–/NO] to change setting. ] If you select “Information” on the network setting screen, the current network setting appears. To return to the network setting screen, press [ENTER] after confirming. 4 Press [ENTER] to complete the operation.
Chapter 10 Enhancing the Disklavier by Hooking Up Other Devices Hooking Up Audio Equipment AV amplifier To audio inputs RCA cord (not supplied) English If you connect the Disklavier to an audio system, you can hear the sound played/played back on the Disklavier from the connected audio system, and the sound played back on the connected audio system from the Disklavier. CD player, etc.
Chapter 10 Enhancing the Disklavier by Hooking Up Other Devices Setting the Disklavier for Audio Data Reception/Transmission [SETUP] “AudioI/O” You can select the kind of the incoming/outgoing audio signals. The following options should be set up in advance. OMNI IN Selects the appropriate option to match the incoming data input to the OMNI (SYNC) IN jacks. Auto Detect: Select this to have the Disklavier detect the input signal automatically.
Chapter Enhancing the Disklavier by Hooking Up Other Devices 10 SYNC IN Offset Adjusts the length of the offset time that leads the actual playback of the entire recording. The offset time can be set in a range of –500ms to +500ms. Decrease this value to delay the piano playing, and increase to advance the piano playing. SYNC OUT Level English Adjusts the output level of the SMPTE signal. For normal use, the adjustment of this option is not required.
Chapter 10 Enhancing the Disklavier by Hooking Up Other Devices 3 Select a desired option with the cursor buttons ([ then press [+/YES] and [–/NO] to change setting. 4 Press [ENTER] to complete the operation. ][ ]), Hooking Up MIDI Devices MIDI (an acronym for Musical Instrument Digital Interface) allows electronic device (synthesizers, etc.) to interact and work in synchronization with other MIDI compatible device.
Chapter Enhancing the Disklavier by Hooking Up Other Devices 10 Setting the Disklavier for MIDI Data Reception [SETUP] “MIDI” The Disklavier can play back the MIDI data being received from the connected MIDI device as well as the software loaded or stored in the Disklavier itself. The following options should be set up in advance. Selects the terminal/port used for the data reception. MIDI: Select this when the MIDI device is connected to MIDI IN terminal.
Chapter 10 Enhancing the Disklavier by Hooking Up Other Devices 1 Press [SETUP] on the remote control. The setup menu screen appears. (1/3) =SETUP MENU= *TimerPlay *AudioI/O *MIDI *M-Tune 2 Select “MIDI” with the cursor buttons ([ then press [ENTER]. ][ ][ ][ ]), 3 Select a desired option with the cursor buttons ([ then press [+/YES] and [–/NO] to change setting. ][ ]), 4 Press [ENTER] to complete the operation.
Chapter Enhancing the Disklavier by Hooking Up Other Devices 10 Setting the Disklavier for MIDI Data Transmission [SETUP] “MIDI” The Disklavier can transmit the information of piano playing/ensemble part playback on the Disklavier as the MIDI data to the connected MIDI device to reproduce the sound with its sound generator, etc. or to record the MIDI data. The following options should be set up in advance. English MIDI OUT Port Selects the terminal/port used for the data transmission.
Chapter 10 Enhancing the Disklavier by Hooking Up Other Devices 3 Select a desired option with the cursor buttons ([ then press [+/YES] and [–/NO] to change setting. 4 Press [ENTER] to complete the operation. ][ ]), Setting the Disklavier for Keyboard Playing Data Transmission [SETUP] “MIDI” Besides the MIDI OUT options, more detailed setups for the keyboard playing data transmission are available. The following options should be set up in advance.
Chapter Enhancing the Disklavier by Hooking Up Other Devices 1 10 Press [SETUP] on the remote control. The setup menu screen appears. (1/3) =SETUP MENU= *TimerPlay *AudioI/O *MIDI *M-Tune English 2 Select “MIDI” with the cursor buttons ([ then press [ENTER]. ][ ][ ][ ]), 3 Select a desired option with the cursor buttons ([ then press [+/YES] and [–/NO] to change setting. ][ ]), 4 Press [ENTER] to complete the operation.
Chapter 11 Other Settings Tuning the Tone Generator (TG Master Tune) [SETUP] “M–Tune” The internal XG tone generator has already been tuned to match the acoustic piano (A3=440 Hz). However, you can re-tune the internal XG tone generator in accordance with the pitch of the acoustic piano by following the procedure below. 1 Press [SETUP] on the remote control. The setup menu screen appears.
Chapter Other Settings 4 Note: To reset to the default factory pitch settings, see Chapter 11 “Other Settings – Resetting the Disklavier” on page 122. Press [ENTER] to complete the operation. English Assigning Frequently-used Functions to the Number Keypad on the Remote Control [SETUP] 11 “Shortcut” You can assign the number keypad of the remote control ([1] thru [9] and [0]) a series of procedures for often used functions. ■ Assigning Functions 1 Press [SETUP] on the remote control.
Chapter 11 Other Settings 4 Press [+/YES] and [–/NO] to select the desired function. =Shortcut= ?=]-+ 3[----] 4[PLAY Mem01 --- ] The following functions are available: Option Description PLAY Starts playback of songs in the selected album or playlist. RPT Starts repeat playback of a song or songs in the selected album or playlist. RND Starts playback of songs in the selected album or playlist at random. RADIO Starts playback of the selected DisklavierRadio channel.
Chapter Other Settings 11 When “RPT” is selected: Option 2 Description Mem01 Mem99 --- Starts repeat playback of all songs in the album selected for option 1 from the first song. 001 - 999 Starts repeat playback of the song selected for option 2 in the album selected for option 1. --- Starts repeat playback of all songs in the playlist selected for option 1 from the first song. 001 - 999 Starts repeat playback of the song selected for option 2 in the playlist selected for option 1.
Chapter 11 Other Settings ■ Using the Shortcut Holding the green button on the remote control, press the corresponding number button on the number keypad to execute the assigned function.
Chapter Other Settings 4 Enter the 4-digit code with the number keypad. =Passcode= _? -+ >Passcode=1234 >MAdr1=##:##:##:##:##:## Note: You can also use [+/YES] and [–/NO] on the remote control, or the dial on the control unit to enter the code. English 5 11 Press [ENTER] to complete the operation. ■ Setting the MAC Address If you feel inconvenient to enter the passcode each time you access from the external remote controller, you can set the MAC address of the external remote controller.
Chapter 11 Other Settings Adjusting the Brightness of the Display [SETUP] “Display” You can adjust the brightness of the display. You can also set the display to dim after the elapse of a certain time if there is no operation. 1 Press [SYSTEM] on the remote control. The system menu screen appears. =STSTEM MENU= (1/2)] *Clock Adj. *TimeZone *Backup *Restore 2 Select “Display” with the cursor buttons ([ [ ]), then press [ENTER].
Chapter Other Settings 4 11 Note: The brightness of the display will return to its original setting when you press any buttons, insert media, or eject media. To set the time for the display to dim, press [ ] to move the cursor to the dim light parameter, then press [+/YES] and [–/NO]. =Display= ?=-+ENT *Brightness=100% *Dim light=1min. English The following time settings are available: OFF, 1min, 2min, 3min, 5min, 10min, 15min, 30min, 45min, 60min.
Chapter 11 Other Settings 3 Press [+/YES] and [–/NO] to select the language. 4 Press [ENTER]. “OK?” flashes in the first line of the screen. 5 Press [+/YES] to set the language, and return to the system menu screen. Resetting the Disklavier [SETUP] “Reset” If you want to return your Disklavier to its initial factory settings, follow the procedure below. 1 Press [SETUP] on the remote control. The setup menu screen appears.
Chapter Other Settings 3 Press [+/YES] and [–/NO] to select the option that you want to reset. English 4 11 Option Description Parameter Reset all parameters, excluding the clock setting and the Internet setting. Memory Reset the internal memory. Factory Init. Reset the Disklavier to its initial factory setting. DeleteCookies Delete the contents of all saved cookies. Press [ENTER]. “OK?” flashes in the first line of the screen. =Reset= OK? YES/NO >Reset=Factory Init.
Chapter 11 Other Settings Diagnosing the Disklavier (Maintenance Mode) [SYSTEM] “Maintenance” The piano diagnostics may be required as the occasion demands. In such a case, follow the instructions of your Yamaha dealer and perform the following procedure. 1 Press [SYSTEM] on the remote control. The system menu screen appears. !"#$%{ 2 Select “Maintenance” with the cursor buttons ([ [ ] [ ]), then press [ENTER].
Chapter Other Settings 4 Select a desired option with the cursor buttons ([ then press [ENTER]. ][ ]), Note: Do not execute these options with no instructions from the service personnel. English The selected option is executed. 5 11 Press [STOP] to complete the operation. Updating the Disklavier Shut down the Disklavier [PLAY/PAUSE] and [ON/OFF] You can update the Disklavier firmware using update program (saved on the CD-ROM or USB flash memory, or downloaded via Internet).
Chapter 11 Other Settings 5 Press [PLAY/PAUSE] to start the update. The update process of the first module takes approximately 3 minutes. MC v2.20 v3.00 DO NOT REMOVE DISK! When the update of the first module completes, the following confirmation message appears. Confirmation message of the second module v3.00 v2.10 CTRL-SURE? (PLAY,STOP) Press [PLAY/PAUSE] to start the update of the second module. The update process of the second module takes approximately 3 minutes.
Chapter 12 Internal Tone Generator Voices The following table lists the basic voices for the internal GM/XG and TG3 tone generator.
Chapter 12 Internal Tone Generator Voices Voice # 128 Display Name Voice # 178 Display Name Timpani Voice # Display Name 128 FngrBass 129 FingrDrk 130 FlangeBa 179 Strings1 229 HiBrass 131 Ba&DstEG 180 S.
Chapter Internal Tone Generator Voices Voice # Display Name Voice # Display Name Voice # Display Name Saw 2 325 Halo Pad 375 BelChoir 276 ThickSaw 326 SweepPad 376 Echoes 277 DynaSaw 327 Shwimmer 377 EchoPad2 278 DigiSaw 328 Converge 378 Echo Pan 279 Big Lead 329 PolarPad 379 EchoBell 280 HeavySyn 330 Celstial 380 Big Pan 281 WaspySyn 13 Synth Effects 282 PulseSaw 331 283 Dr.
Chapter 12 Internal Tone Generator Voices Voice # Display Name Voice # Display Name Voice # Display Name 424 Mel Tom2 459 Feed 485 Punch 425 Real Tom 460 Dog 486 Heart 426 Rock Tom 461 Horse 487 FootStep 427 Syn.Drum 462 Bird 2 488 MchinGun 428 Ana Tom 463 Ghost 489 LaserGun 429 ElecPerc 464 Maou 490 Xplosion 430 RevCymbl 465 Tel.
Chapter Internal Tone Generator Voices Voice # Display Name Voice # Display Name 046 Pizz.Str 091 PolySyPd 047 Harp 092 ChoirPad 048 Timpani 093 BowedPad 094 MetalPad 07 Ensemble Strings1 095 Halo Pad 050 Strings2 096 SweepPad 051 Syn.Str1 052 Syn.Str2 097 Rain 053 ChoirAah 098 SoundTrk 054 VoiceOoh 099 Crystal 055 SynVoice 100 Atmosphr 056 Orch.
Chapter 13 Troubleshooting If you are having difficulty operating the Disklavier, see if any of the symptoms listed below apply to your problem and follow the recommended remedy. Power Symptom The Diskalvier does not turn on. Remedy Make sure that the main switch on the power supply unit is turned on. Make sure that the AC power cable is securely connected to a suitable AC wall outlet. If the Disklavier still cannot be turned on, disconnect it from the AC wall outlet, and consult your Disklavier dealer.
Chapter Troubleshooting 13 Playback Symptom None of the playback functions can be used. The Disklavier does not read a song file. Songs are not played back in the normal song order. The playback order differs from the order on another device. When selecting a song using the remote control’s number keypad, but the last song on the album is selected. When specifying a search time using the remote control’s number keypad, but the end of the song is selected.
Chapter 13 Troubleshooting Media Symptom The Disklavier does not read a CD-R/RW disc. Remedy The audio CD should be formatted in CD-DA, and the data CD in ISO 9660 Level1. The Disklavier may not read a CD-R/RW disc other than this format. Connection with External Devices Symptom The Disklavier cannot send or receive MIDI data with other MIDI instruments.
Chapter 14 Error Messages While operating your Disklavier, an error message may appear in the display. If an error message appears, refer to the table below for an explanation of the message. Media Selection / Playback Situation Remedy NO MEDIA! You selected the medium that has not been inserted. Insert the medium or select another medium. DIFFERENT CD! Your CD is not paired with the selected SmartPianoSoft song. Insert appropriate CD that is paired with the SmartPianoSoft song.
Chapter 15 Glossary This glossary provides basic definitions of terms used frequently in Disklavier manuals. Continuous Pedal General MIDI (GM) See “Incremental Pedal.” An addition to the MIDI standard that simplifies the transfer of MIDI song files between instruments of different manufacturers. A MIDI song recorded using a GM compatible tone generator should play back correctly when used with any GM compatible tone generator.
Chapter Glossary MIDI Router An acronym for Musical Instrument Digital Interface. MIDI allows electronic musical instruments to communicate with each other. A device for connecting multiple computer networks. For example, a router is necessary when connecting several computers in a house or office, to allow all of them access the Internet and share data. A router is usually connected between a modem and a computer, although some modems have a built-in router.
Chapter 15 Glossary Tone Generator An electronic device that can generate tones or instrument voices. Transpose Changing the key of a song. For example, a song in the key of C is transposed to the key of D when it is moved up two semitones. USB An interface for connecting an external device with plug and play. The Disklavier supplies with 2 TO DEVICE terminal with USB 1.1 standard and 1 TO HOST terminal.
Chapter 16 Specifications General Specifications Drive System Data Storage Key Sensors Noncontact optical fiber/grayscale shutter sensing system for 88 keys (senses the key position, keying velocity, and key releasing velocity) Pedal Sensors Damper pedal: Noncontact optical position-sensing system Keys DSP servo drive system (servocontrolled solenoids) Damper DSP servo drive system (servocontrolled solenoids) Internal Memory 128 MB Compact Disc Audio CD (CD-DA), Data CD (ISO 9660 Level1-comp
Chapter 16 Specifications Function & Controls Playback Functions Playback Controls Recording Functions Piano Playing Functions Metronome Utility Functions Media Select Internal memory, CD, USB media (including floppy disk) Song Select Cursor buttons (control unit), cursor buttons/numeric section (remote control) Basic Functions Play, stop, pause Song Search Reverse/forward w/sound (MIDI songs), reverse/forward w/o sound (audio songs), directly by time or measure.
Classic Appendix Appendix
Software License Notice GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright © 1989, 1991 Free Software Foundation, Inc. 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. ■ Preamble The licenses for most software are designed to take away your freedom to share and change it.
Software License Notice ■ TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0 This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License.
Software License Notice 3.
Software License Notice If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
Software License Notice GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright © 1991, 1999 Free Software Foundation, Inc. 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.
Software License Notice When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library.
Software License Notice 1. You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.
Software License Notice 4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange.
Software License Notice c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution. d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place.
Software License Notice If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.
Software License Notice expat Copyright © 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark Cooper Copyright © 2001, 2002, 2003 Expat maintainers.
Software License Notice THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Software License Notice CARNEGIE MELLON ALLOWS FREE USE OF THIS SOFTWARE IN ITS “AS IS” CONDITION. CARNEGIE MELLON DISCLAIMS ANY LIABILITY OF ANY KIND FOR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THIS SOFTWARE. Carnegie Mellon requests users of this software to return to Software Distribution Coordinator School of Computer Science Carnegie Mellon University Pittsburgh PA 15213-3890 or Software.Distribution@CS.CMU.
Software License Notice THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Software License Notice 1. Redistributions of source code must retain any existing copyright notice, and this entire permission notice in its entirety, including the disclaimer of warranties. 2. Redistributions in binary form must reproduce all prior and current copyright notices, this list of conditions, and the following disclaimer in the documentation and/or other materials provided with the distribution. 3.
Software License Notice ntp Copyright Notice jpg “Clone me,” says Dolly sheepishly Last update: 02:45 UTC Tuesday, June 27, 2006 The following copyright notice applies to all files collectively called the Network Time Protocol Version 4 Distribution. Unless specifically declared otherwise in an individual file, this notice applies as if the text was explicitly included in the file. Copyright © David L.
Software License Notice OpenLDAP is a registered trademark of the OpenLDAP Foundation. Copyright 1999-2003 The OpenLDAP Foundation, Redwood City, California, USA. All Rights Reserved. Permission to copy and distribute verbatim copies of this document is granted. openssl LICENSE ISSUES The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. See below for the actual license texts.
Software License Notice This package is an SSL implementation written by Eric Young (eay@cryptsoft.com). The implementation was written so as to conform with Netscapes SSL. This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code.
Software License Notice pam Unless otherwise *explicitly* stated the following text describes the licensed conditions under which the contents of this Linux-PAM release may be distributed: Redistribution and use in source and binary forms of Linux-PAM, with or without modification, are permitted provided that the following conditions are met: 1.
Software License Notice 1. Redistributions of source code must retain the above copyright notice, definition, disclaimer, and this list of conditions. 2. Redistributions in binary form (compiled executables) must reproduce the above copyright notice, definition, disclaimer, and this list of conditions in documentation and/or other materials provided with the distribution.
MIDI Data Format If you are familiar with MIDI, or are using a computer to control your music software with computergenerated MIDI messages, the data provided in this section can help you to control your Disklavier. Messages include those that can be received by the piano part and/or those that can be received by an ESBL part. Messages that can be transmitted as well as received are shown as “transmitted.” 1. CHANNEL MESSAGES 1.
MIDI Data Format 1.2.18 Effect3 Depth (Chorus Send Level) $1D $rr $mm $1E $rr $mm $1F $rr $mm (ESBL Part) Cntrl# 93 Parameter Effect3 Depth Data Range 0...127 1.2.19 Effect4 Depth (Variation Effect Send Level) (ESBL Part) Cntrl# 94 Parameter Effect4 Depth Data Range 0...127 1.2.20 Data Increment / Decrement (for RPN) (ESBL Part) Cntrl# 96 97 Parameter RPN Increment RPN Decrement Data Range 0...127 0...127 1.2.
MIDI Data Format Portamento Control RPN NRPN 1.2.23.3 cancels the Portamento Source Key Number that was received number not specified; internal data will not change number not specified; internal data will not change All Note Off (Piano Part, ESBL Part) (transmitted) [OTHER] 1) Master tuning 2) TG300 System Data Parameter change 3) TG300 Multi Effect Data parameter change 4) TG300 Multi Part Data parameter change 2.1.2 2.1.2.
MIDI Data Format For parameters with data size of 2 or 4, transmit the appropriate number of data bytes. When sending the parameter change messages consecutively, be sure to leave an appropriate interval (if the time base is 480. ca 5 unit) between the messages. 2.1.4.1 2.2.
MIDI Data Format 3. SYSTEM REALTIME MESSAGES 3.1 Active Sensing a) Transmission Transmitted. b) Reception Once FE has been received. if no MIDI data is subsequently received for longer than an interval of approximately 300msec. the Disklavier will perform the same function as when ALL SOUNDS OFF. ALL NOTES OFF, and RESET ALL CONTROLLERS messages are received, and will then return to a status in which FE is not monitored. 3.2 3.
MIDI Data Format TOTAL SIZE 02 01 10 11 12 13 14 15 TOTAL SIZE 02 01 20 0E 1 1 1 1 1 1 6 2 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E TOTAL SIZE 02 01 30 31 32 33 34 35 TOTAL SIZE 02 01 40 1 1 1 1 1 1 1 1 1 1 1 1 1 0F 1 1 1 1 1 1 6 2 42 2 44 2 46 2 48 2 4A 2 4C 2 4E 2 50 2 52 2 54 2 56 57 58 59 5A 5B 1 1 1 1 1 1 5C 5D 5E 5F 60 TOTAL SIZE 02 01 70 71 72 73 74 75 TOTAL SIZE A-26 1 1 1 1 1 21 1 1 1 1 1 1 6 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F REVERB PARAMETER 11 REVERB PARAMETER 12 REV
MIDI Data Format
MIDI Parameter Change table (MULTI PART) [XG] Address (H) 08 nn nn nn nn nn nn 00 01 02 03 04 05 Size (H) 1 1 1 1 1 1 Data (H) 00 - 20 00 - 7F 00 - 7F 00 - 7F 00 - 0F, 7F 00 - 01 nn 06 1 00 - 02 nn 07 1 00 - 03 nn nn nn 08 09 0A 1 2 28 - 58 00 - FF nn nn nn nn nn nn nn nn nn nn 0B 0C 0D 0E 0F 10 11 12 13 14 1 1 1 1 1 1 1 1 1 1 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F 0 - 32 0 - 127 0 - 127 1 - 128 1 - 16,OFF 0:MONO 1:POLMIDI Data Format nn nn nn nn nn nn nn nn nn nn nn 42 43 44 45 46 47 48 49 4A 4B 4C 1 1 1 1 1 1 1 1 1 1 1 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F SCALE TUNING C# SCALE TUNING D SCALE TUNING D# SCALE TUNING E SCALE TUNING F SCALE TUNING F# SCALE TUNING G SCALE TUNING G# SCALE TUNING A SCALE TUNING A# SCALE TUNING B -64 - +63 [cent] -64 - +63 [cent] -64 - +63 [cent] -64 - +63 [cent] -64 - +63 [cent] -64 - +63 [cent] -64 - +63 [cent] -64 - +63 [cent] -64 - +6
MIDI Data Format 3n rr 08 3n rr 09 3n rr 0A 3n rr 0B 3n rr 0C 3n rr 0D 3n rr 0E 3n rr 0F TOTAL SIZE 1 1 1 1 1 1 1 1 10 00 - 01 00 - 01 00 - 01 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F KEY ASSIGN Rcv NOTE OFF Rcv NOTE ON FILTER CUTOFF FREQUENCY FILTER RESONANCE EG ATTACK RATE EG DECAY1 RATE EG DECAY2 RATE 0/SINGLE, 1/MULTI 0/OFF, 1/ON 0/OFF, 1/ON -64 - +63 -64 - +63 -64 - +63 -64 - +63 -64 - +63 00 Depends on the note 01 40 40 40 40 40 [Note] n: Drum number (0 - 1) rr: note number (0D - 5B) When XG syst
MIDI Data Format 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 00-3F 00-7F 00-7F 00-7F 00-7F 00-7F 00-3F 00-07 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 39-47 39-47 39-47 00-7F 00-3F 00-3F 00-3F 00-3F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-06 00-0F 39-47 00-7F 00-0F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 39-47 8D : DC DD : 12C
MIDI Data Format XG Normal Voice List Bank Select MSB = 000, LSB = Bank Number Voice names in bold typeface are voices that can be selected in the Disklavier. The Disklavier can produce all the voices listed below, but can only display bank 0 voices.
MIDI Data Format Bank Select MSB = 064, LSB = 000 SFX Voice Instrument Program Bank Group # # Reed 65 0 66 0 40 43 67 0 40 41 64 68 0 69 0 70 0 71 0 72 0 Pipe 73 0 74 0 75 0 76 0 77 0 78 0 79 0 80 0 Synth Lead 81 0 6 8 18 19 64 65 66 82 0 6 8 18 19 20 24 25 40 41 45 96 83 0 65 84 0 64 85 0 64 65 86 0 24 64 87 0 35 88 0 16 64 65 Synth Pad 89 0 64 90 0 16 17 18 64 65 91 0 64 65 66 67 A-32 EleVoice Name ment SprnoSax 1 Alto Sax 1 Sax Sect 2 HyprAlto 2 TenorSax 1 BrthTnSx 2 SoftTenr 2 TnrSax 2 1 Bari.
MIDI Data Format TG300B Normal Voice List Bank Select MSB = Bank Number, LSB = ooo Instrument Group Piano Instrument Group Organ Guitar Program Bank Voice Name # # 17 0 DrawOrgn 1 70sDrOr1 8 DetDrwOr 9 70sDrOr2 16 60sDrOr1 17 60sDrOr2 18 60sDrOr3 24 CheezOrg 32 DrawOrg2 33 EvenBar 40 Organ Ba 126 Slap-2 127 harpsi1 18 0 PercOrgn 1 70sPcOr1 8 DetPrcOr 32 PercOrg2 126 Slap-3 127 harpsi2 19 0 RockOrgn 8 RotaryOr 16 SloRotar 24 FstRotar 126 Slap-4 127 harpsi3 20 0 ChrchOrg 8 ChurOrg2 16 ChurOrg3 24 OrgFlute
MIDI Data Format Instrument Group Brass Reed Pipe A-34 Program Bank Voice Name # # 57 0 Trumpet 1 Trumpet2 24 BriteTrp 25 WarmTrp 126 Sax-3 127 contrabs 58 0 Trombone 1 Trmbone2 126 Sax-4 127 harp 1 59 0 Tuba 1 Tuba 2 126 Brass-1 127 harp 2 60 0 Mute.Trp 126 Brass-2 127 guitar 1 61 0 Fr.
MIDI Data Format XG Drum Voice List Bank Select MSB = Bank Number, LSB = 000 Drum kit names in bold typeface are those that can be selected in the Disklavier.
MIDI Data Format TG300B Drum Voice List Program # Note# Note Alternate 1 9 17 25 26 33 41 49 57 128 Standard Kit Room Kit Power Kit Electro Kit Analog Kit Jazz Kit Brush Kit Orchestra Kit SFX Set C/M Kit assign 0 Snare Roll 26 D 0 Finger Snap 27 25 D# C# 0 Hi Q Hi-Hat Closed 28 E 0 Whip Slap Hi-Hat Pedal 29 F 0 7 Scratch Push Hi-Hat Open 30 F# 0 7 Scratch Pull Ride Cymbal 1 31 G 0 Sticks 32 G# 0 Click Noise 33 A 0 Metronome Click 34 A# 0 Me
MIDI Data Format Effect Type List Effect Type Description Effect turned off. Reverb simulating the resonance of a hall. Reverb simulating the resonance of a hall. Reverb simulating the resonance of a room. Reverb simulating the resonance of a room. Reverb simulating the resonance of a room. Reverb appropriate for a solo instrument. Reverb appropriate for a solo instrument. Reverb simulating a metal plate reverb unit. A unique short reverb with a bit of initial delay.
MIDI Data Format Effect Parameter List No Parameter Range Value HALL1, HALL2, ROOM 1, 2, 3, STAGE 1, 2, PLATE 1 Reverb Time 0.3~30.0s 0-69 2 Diffusion 0~10 0-10 3 Initial Delay 0~63 0-63 4 HPF Cutoff Thru~8.0kHz 0-52 5 LPF Cutoff 1.0k~Thru 34-60 6 7 8 9 10 Dry/Wet D63>W~D=W~DR ~ E=R ~ E>R63 1-127 14 15 Feedback Level -63~+63 1-127 16 WHITE ROOM, TUNNEL, BASEMENT 1 Reverb Time 0.3~30.
MIDI Data Format No Parameter Range See Table 0-127 1-127 0-52 34-60 table#7 1-127 0-127 0-127 1-127 0-127 8-40 52-76 28-58 52-76 1-127 Control • table#1 table#2 table#3 table#3 • 0-1 8-40 52-76 28-58 52-76 1-127 table#1 table#2 table#3 table#3 • 4-124 0-127 0-127 0-127 8-40 52-76 28-58 52-76 1-127 table#1 table#2 table#3 table#3 • Range ROTARY SPEAKER 1 LFO Frequency 0.00~39.7Hz 2 LFO Depth 0~127 3 4 5 6 EQ Low Frequency 50Hz~2.0kHz 7 EQ Low Gain -12~+12dB 8 EQ High Frequency 500Hz~16.
MIDI Data Format No Parameter Range DISTORTION, OVERDRIVE 1 Drive 0~127 2 EQ Low Frequency 50Hz~2.0kHz 3 EQ Low Gain -12~+12dB 4 LPF Cutoff 1.0k~Thru 5 Output Level 0~127 6 7 EQ Mid Frequency 500Hz~10.0kHz 8 EQ Mid Gain -12~+12dB 9 EQ Mid Width 1.0~12.0 10 Dry/Wet D63>W~D=W~D
MIDI Data Format Effect Data Assign Table Table#2 Table#1 Value Data 0.00 43 0.04 44 0.08 45 0.13 46 0.17 47 0.21 48 0.25 49 0.29 50 0.34 51 0.38 52 0.42 53 0.46 54 0.51 55 0.55 56 0.59 57 0.63 58 0.67 59 0.72 60 0.76 61 0.80 62 0.84 63 0.88 64 0.93 65 0.97 66 1.01 67 1.05 68 1.09 69 1.14 70 1.18 71 1.22 72 1.26 73 1.30 74 1.35 75 1.39 76 1.43 77 1.47 78 1.51 79 1.56 80 1.60 81 1.64 82 1.68 83 1.72 84 1.77 85 Value Data 1.81 86 1.85 87 1.89 88 1.94 89 1.98 90 2.02 91 2.06 92 2.10 93 2.15 94 2.19 95 2.
Yamaha Disklavier Model: E3 Classic MIDI IMPLEMENTATION CHART Function...
P. O. Box 1, Hamamatsu, 430-8650 Japan Copyright © 2014 by Yamaha Corporation This document is printed on chlorine free (ECF) paper.
