User Manual

3
Deleting the version update data
Please turn off the power of the STAGEA if it is on.
1 Connect the USB flash drive containing the
version update data.
2 Simultaneously hold down the [START]
button in the Rhythm section on the panel
and turn on the power switch.
Keep holding down the [START] button until the display
below appears.
3 Press the [BREAK] button in the Rhythm
section on the panel.
4 The Delete operation starts when you press
the [START] button in the Rhythm section.
NOTICE
Make sure that you do not disconnect the USB flash
drive, or turn off the power during the Delete operation.
Doing so may result in damage to the USB flash drive.
5 The Delete operation is complete when the
message below appears in the display.
Turn off the STAGEA and disconnect the USB flash drive.
Supplemental instructions
㻵㻌㼚㻌㼟㻌㼠㻌㼍㻌㼘㻌㼘㻌㼑㻌㼞
㼇㻿㼀㻭㻾㼀㼉㻦 㻵㻌㼚㻌㼟㻌㼠㻌㼍㻌㼘㻌㼘
㼇㻮㻾㻱㻭㻷㼉㻦 㻰㻌㼑㻌㼘㻌㼑㻌㼠㻌㼑
㻼㻌㼞㻌㼑㻌㼟㻌㼟㻌㻌㻌㼠㻌㼔㻌㼑㻌㻌㻌㼎㻌㼡㻌㼠㻌㼠㻌㼛㻌㼚
㼅㻌㼍㻌㼙㻌㼍㻌㼔㻌㼍㻌㻌㻌㻯㻌㼛㻌㼞㻌㼜㻚
㻵㻌㼚㻌㼟㻌㼠㻌㼍㻌㼘㻌㼘㻌㼑㻌㼞
㼇 㻿 㼀 㻭 㻾 㼀 㼉 㻦 㻱㻌㼤㻌㼑㻌㼏㻌㼡㻌㼠㻌㼑
㼇 㻮 㻾 㻱 㻭 㻷 㼉 㻦 㻯㻌㼍㻌㼚㻌㼏㻌㼑㻌㼘
㻼㻌㼞㻌㼛㻌㼓㻌㼞㻌㼍㻌㼙㻌㻌㻌㼢㻌㼑㻌㼞㻌㻚㻌㼄㻚㻌㼄㻌㼄
㼅㻌㼍㻌㼙㻌㼍㻌㼔㻌㼍㻌㻌㻌㻯㻌㼛㻌㼞㻌㼜㻚
㻵㻌㼚㻌㼟㻌㼠㻌㼍㻌㼘㻌㼘㻌㼑㻌㼞
㻯㻌㼛㻌㼙㻌㼜㻌㼘㻌㼑㻌㼠㻌㼑㻌㼐㻚
㼀㻌㼡㻌㼞㻌㼚㻌㻌㻌㼛㻌㼒㻌㼒㻌㻌㻌㼜㻌㼛㻌㼣㻌㼑㻌㼞㻚
㼅㻌㼍㻌㼙㻌㼍㻌㼔㻌㼍㻌㻌㻌㻯㻌㼛㻌㼞㻌㼜㻚