Revolabs Elite™ Wired Microphones Installation and Operation Guide Models: 01-EWM5-DR-BLK 01-EWM5-OM-BLK 01-EWM5-GN6-BLK 01-EWM5-GN12-BLK 01-EWM5-DR-WHT 01-EWM5-OM-WHT 01-EWM5-GN6-WHT 01-EWM5-GN12-WHT 01-EWM5-DR-BNI 01-EWM5-OM-BNI 01-EWM5-GN6-BNI 01-EWM5-GN12-BNI
© YAMAHA UNIFIED COMMUNICATIONS INC. All rights reserved. No part of this document may be reproduced in any form or by any means without express written permission from Yamaha Unified Communications, Inc. Product specifications are subject to change without notice.
Introduction Congratulations on your purchase of the Revolabs Elite™ Wired Microphone with Mute control and indicator light. This microphone utilizes state of the art technology providing high bandwidth audio and enabling clear, reliable audio capture for your applications. Please read this documentation carefully and follow the instructions before installing and using your Elite™ Wired Microphone.
Safety and General Information Please read the following information to ensure safe and efficient use of your Revolabs system. FCC Notice to Users This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Users are not permitted to make changes or modify the equipment in any way.
Industry Canada Notice to Users Operation is subject to the following two conditions: (1) This device may not cause interference and (2) This device must accept any interference, including interference that may cause undesired operation of the device Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
WEEE Notification The Waste Electrical and Electronic Equipment (WEEE) directive (2012/19/EU) is intended to promote recycling of electrical and electronic equipment and their components at end of life. According to the requirement of the WEEE legislation the following user information is provided to customers for all branded Yamaha Unified Communications Inc. products subject to the WEEE directive.
Content Introduction ............................................................................................................................................ 3 Safety and General Information ....................................................................................................... 4 FCC Notice to Users ........................................................................................................................................... 4 Industry Canada Notice to Users ................
Components Your Revolabs Elite Wired Microphone comes with a 15' (4.5 m) cable attached to connect it to a phantom powered microphone input of a digital signal processor (DSP), or other audio devices. The packaging includes the microphone with cable and a short installation documentation. The Revolabs Elite system is designed to optimize audio capture by providing consistent and high-level audio input from all participants.
Installation The Elite Wired Microphones with Mute Control and Indicator are equipped with a 15' (4.5 meter) cable that allows integration with audio equipment. If the microphone mute is controlled locally, only the audio wires (mic positive (red), mic negative (black), and ground) need to be connected to the audio equipment.
External Control When external Control is desired, DIP switch One needs to be in the ON position. Switch Position Mode 1 2 3 4 5 6 External Control Enabled, >2.8V in = Red LED , <2.4V in = Green LED ON OFF OFF OFF OFF OFF External Control Enabled, >2.8V in = Green LED , <2.4V in = Red LED ON ON OFF OFF OFF OFF DIP switches 3 – 6 should be in the OFF position.
If more than one of the DIP switches 3 – 6 is in the ON position, unwanted and unpredictable microphone mute behavior will be observed and audio distortions will be experienced. In Push to Mute mode, the microphone send audio data, unless the button is pressed, at which time the microphone will mute. In Push to Talk mode, the microphone is muted, unless the user presses the button, at which time the microphone sends audio data until the button is released again.
Note: The Elite Wired Microphone includes some active electronic circuitry, and therefore requires Phantom Power to be provided from the device the microphone is connected to. The Elite Wired Microphone requires a phantom voltage between 12 and 48V DC, with a draw of maximum 2mA. Control Wire Connection The Control wires will be connected with the GPIO ports of the DSP or other technology that is controlling the mute status of the microphones.
2 3 1 1. Bottom door latch — open the bottom to change the DIP switch settings. Or replace the bottom cover for permanent installations using this latch. 2. Audio wire — connect the microphone to the DSP or other audio equipment using this wire. 3. Button – Local mute control, or pulling the external control line to ground when pressed. To use the Elite Omni-Directional Tabletop Microphone, it should be centered on the table within 2 to 6 feet (0.
The Elite Directional Wired Tabletop Boundary Microphones The Elite Directional Wired Tabletop Boundary Microphone, shown below, is designed to provide optimum coverage when placed on a conference room table in front of one to three people. 2 3 1 1. Bottom door latch — replace the bottom cover for permanent installations using this latch. 2. Audio wire — connect the microphone to the DSP or other audio equipment using this wire. 3.
video conference speaker to avoid echoes. Make sure that the microphone’s rubber feet are sitting atop a flat surface. The Elite Gooseneck Tabletop Microphones The Elite Gooseneck Tabletop Microphones, 6 inch and 12 inch (15 cm and 30 cm, respectively), shown below, are designed to provide optimum coverage when placed on a conference room table in front of one person. 1 2 1. Button – Local mute control, or pulling the external control line to ground when pressed. 2.
the discretion of the Seller) will be free of charge for the period defined in the Yamaha Unified Communications Inc. Professional Products Limited Warranty. Any attempt by the user to alter the equipment, or equipment damaged by negligence, accident, or Acts of God voids this warranty. The Seller shall not be liable for any consequential damage resulting from the malfunction of this product.
Directional Tabletop Goseneck Microphones Local mute attenuation 100dB minimum Frequency Response SNR Max SPL @1kHz, 1% THD Dynamic Range Sensitivity @1kHz Local mute attenuation 160Hz – 16,000 Hz 68 dB 113 dBSPL 87 dB -36.2dBV 100dB minimum Frequency Response SNR Max SPL @1kHz, 1% THD Dynamic Range Sensitivity @1kHz Local mute attenuation 160Hz – 16,000 Hz 68 dB 113 dBSPL 87 dB -36.
Microphone Polar Patterns Elite Omni-Directional Wired Tabletop Microphone : Elite Directional Wired Tabletop Microphone: 18
Elite Gooseneck 6 or 12 inch (15 cm or 30 cm, respectively) Tabletop Microphone: MN-ELITE-WIRED-MICS-INSTALLATION AND OPERATION-GUIDE-20180508-EN Copyright 2018 Yamaha Unified Communications, Inc.