ELS-01/01C/01X 取扱説明書 日本マニュアルコンテスト2004 家庭製品第一部門 優秀賞受賞 JA
安全上のご注意 ご使用の前に、必ずこの「安全上のご注意」をよくお読みください。 ここに示した注意事項は、製 品を安全に正しくご使用いただき、お客様や他の方々 への危害や財産への損害 を未然に防止するためのものです。必ずお守りください。 お子様がご使用になる場 合は、保護者の方が以下の内容をお子様にご徹底ください ますようお願いいたしま す。 お読みになったあとは、使用される方がいつでも見られる所に必ず保管してください。 ■ 記号表示について この製品や取扱説明書に表示されている記号には、次のような意味があります。 「ご注意ください」という注意喚起を示します。 〜しないでくださいという「禁止」を示します。 「必ず実行」してくださいという強制を示します。 ■ 「警告」と「注意」について 以下、誤った取り扱いをする と生じることが想定される内容を、危害や損害の大き さと切迫の程度を明示す るために、「警告」と「注意」に区分して掲載しています。 警告 この表示の欄は、 「死亡す る可能性または重傷を負 う可能性が想定される」 内容です。 注意 この表示の欄は、 「傷害を 負う可能性または物的損 害が発生す
警告 電源 / 電源コード 水に注意 電源は必ず交流100V を使用する。 エアコンの電源など交流200Vのものがあります。誤って接 本体の上に花瓶や薬品など液体の入ったものを置かない。 また、浴室や雨天時の屋外など湿気の多いところで使用しな 続すると、感電や火災のおそれがあります。 必ず実行 禁止 電源プラグにほこりが付着している場合は、ほこりをきれい 濡れた手で電源プラグを抜き差ししない。 に拭き取る。 感電やショートのおそれがあります。 感電のおそれがあります。 必ず実行 禁止 電源コードをストーブなどの熱器具に近づけたり、無理に曲 げたり、傷つけたりしない。また、電源コードに重いものを 禁止 火に注意 のせない。 電源コードが破損し、感電や火災の原因になります。 本体の上にろうそくなど火気のあるものを置かない。 ろうそくなどが倒れたりして、火災の原因になります。 分解禁止 禁止 この製品の 内部を開け た 異常に気づいたら り、内部の部 品を分解 し たり改造したりしない。 禁止 い。 感電や火災、または故障の原因になります。 電源コード /プラグがいたんだ場
組み立て 接続 他の機器と接続する場合は、すべての機器の電源を切った上 で行なう。また、電源を入れたり切ったりする前に、必ず機 組み立てる前に、必ず本書 227 ページの組み立て方の説明 をよくお読みください。 必ず実行 手順どおりに正しく組み立てないと、楽器が破損したりお客 様がけがをしたりする原因になります。 必ず実行 器のボリュームを最小にする。さらに、演奏を始める場合も 必ず両機器のボリュームを最小にし、演奏しながら徐々にボ リュームを上げていき適切な音量にする。 感電または機器の損傷の原因になることがあります。 設置 直射日光のあたる場所(日中の車内など)やストーブの近く など極端に温度が高くなるところ、逆に温度が極端に低いと ころ、また、ほこりや振動の多いところで使用しない。 禁止 本体のパネルが変形したり、内部の部品が故障したりする原 因になります。 テレビやラジオ、ステレオ、携帯電話など他の電気製品の近 くで使用しない。 楽器本体ま たはテレビ やラジオな どに雑音が 生じる場合 が 禁止 あります。 手入れ 本体を手入れするときは、ベンジンやシンナー、洗剤、化学 ぞうきん
本体の上にのったり重いものをのせたりしない。また、ボタ ンやスイッチ、入出力端子などに無理な力を加えない。 禁止 本体が破損したり、お客様や他の方々がけがをしたりする原 因になります。 データの保存 作成したデータの保存とバックアップ 必ず実行 パネル上または画面上で設定されたデータは電源を切 ると消えてしまいます。 消去したくないデータは、電源 を切る前にレジストレーションメモリーに保存してく ださい (83 ページ )。また、 レジストレーションメモリー に保存したデータは、 故障や誤操作などのために失われ ることがあります。大切なデータは、 スマートメディア / 外部メディアに保存してください (86 ページ )。 スマートメディア / 外部メディアのバックアップ 大きな音量で長時間ヘッドフォンを使用しない。 聴覚障害の原因になります。 禁止 必ず実行 保存したスマートメディア / 外部メディアの万一の事故 に備えて、大切なデータは予備のスマートメディア / 外 部メディアにバックアップとして保存されることをお すすめします。 イス 不安定な場所に置かない。 イスが転倒して、お客様や
はじめに このたびは、ヤマハエレクトーンSTAGEA ELS-01/01C/01Xをお買い上げいただきまして、ありがとう ございます。 ELS-01/01C/01Xは、長年にわたって培ってきたノウハウと最新の電子テクノロジーの粋を集めて完成され たエレクトーンです。ほとんどの機能は、直感的に操作できるタッチパネルで設定できます。 ELS-01/01C/01Xのバラエティあふれる機能のすべてを使って演奏をお楽しみいただくために、ぜひこの 取扱説明書をご活用いただきますようお願い申しあげます。 また、ご一読いただいたあとも、不明な点が生じた場合に備えて、大切に保管いただきますようお願いします。 付属品(お確かめください) • 椅子 • 取扱説明書(本書) • 活用ガイド • 記録用スマートメディア • 保証書 • ユーザー登録のご案内 6 ELS-01/01C/01X 取扱説明書
ELS-01/01C/01Xの特長 豊富なレジストレーションメニュー 21ページ すぐにイメージに合うレジストレーションを引き出せるように、パネル上の5つのボタンにハイクオリティで使い 勝手の良い240種類のレジストレーションが用意されています。さらにELS-01C/01Xでは、カスタム鍵盤やVA 音色、オルガンフルート音色に対応したレジストレーションが60種類搭載されています。それぞれのレジストレー ションはジャンル別に分類されており、初心者の方には選んだだけですぐに弾けるように、中〜上級者の方には、 レジストレーションメニューを出発点として、思いどおりに加工し、効率の良いレジストレーションづくりができ るようになっています。 4レイヤー AWM音源を使った多彩なボイスとハイクオリティなデジタルエフェクト 24ページ、53ページ クオリティの高いAWM音源による415種類のボイスを搭載。さらにELS-01C/01XではVA音源による94種類の VA音色と本格的なオルガンフルート音色も搭載しています。鍵盤の持つ高い表現力とあわせて、表情豊かな音色を 奏でることができます。また、15カテゴリー、183
ELS-01/01C/01Xは、下記のフォーマットや機能に対応しています。 「GM (General MIDI)」とは、メーカーや機種が異なった音源でも、ほぼ同じ系統の音色で演奏が再現さ れることを目的に設けられた、音源の音色配列やMIDI機能に関する一定の基準のことです。 「GM2」とは、 「GM」に対し同時発音数、音色数、音色パラメーター、エフェクトなどの機能を拡張して 規定することにより、曲データの更なる互換性を向上させることが可能な一定の基準です。「GM2」 に準 拠した音源やソングデータには、このGM2マークがついています。 「XG」とは、音色の配列に関する「GM」をより拡張し、時代と共に複雑化、高度化していくコンピュー ター周辺環境にも対応させ、豊かな表現力とデータの継続性を可能とした音源フォーマットです。「XG」 では、音色の拡張方式やエディット方式、エフェクト構成やタイプなどを規定して、「GM」を大幅に拡張 しました。 XGマークのついた市販ソングデータを、XGマークのついた音源で再生することによって、無数の拡張ボ イスやエフェクト機能までも含めた壮大な演奏を手軽に楽しむことができます。 「G
目次 C O N T EN TS はじめに .........................................................................6 付属品(お確かめください)........................................ 6 ELS-01/01C/01Xの特長........................................ 7 目次......................................................... 9 1 基本操作 2 ボイス(楽器音色) 3 オルガンフルート (ELS-01C/01X) 4 コントロールと エフェクト 5 リズム/ キーボードパーカッション 6 レジストレーション メモリー 7 ミュージックデータ レコーダー(MDR) 8 ボイスエディット 9 リズムプログラム 8 ボイスエディット .............................132 ボイスの構成 ......................
各部の名称 操作パネル (イラストはELS-01Cのものです) LOWER KEYBOARD VOICE1、2 (下鍵盤ボイス)25ページ REVERB(リバーブ)ボタン 46ページ UPPER KEYBOARD VOICE1、2 (上鍵盤ボイス) 24ページ UPPER KEYBOARD VOICE 1 REVERB BRILLIANCE MAX BRILLIANT モニタースピーカー STRINGS BRASS WOODWIND TUTTI PAD SYNTH 1 PIANO ORGAN PERCUSSION GUITAR CHOIR WORLD 2 MIN MELLOW LOWER KEYBOARD VOICE 1 SUSTAIN SUSTAIN(サステイン) ボタン 50ページ BRILLIANCE BRILLIANT UPPER (KNEE) LOWER (KNEE) PEDAL STRINGS BRASS WOODWIND TUTTI PAD SYNTH 1 PIANO ORGAN PERCUSSION GUITA
LCDディスプレイ/ DISPLAY SELECT (ディスプレイセレクト) 12ページ PEDAL VOICE 1、2 (ペダルボイス) 25ページ DISPLAY SELECT VOICE DISPLAY A.B.C. M.O.C.
LCDディスプレイ/ディスプレイセレクト DISPLAY SELECT 1 VOICE DISPLAY 3 FOOT SWITCH 6 A.B.C. M.O.C. 4 UTILITY 7 5 MDR INTERNET 8 DATA CONTROL RHYTHM PROGRAM VOICE EDIT PATTERN SEQUENCE 9 U.ORGAN FLUTES @ ) ! L.ORGAN ROTARY SP SPEED FLUTES # $ 2 1 2 3 4 5 6 7 LCDディスプレイ(タッチパネル) 14ページ DATA CONTROL (データコントロール)ダイアル 16ページ [VOICE DISPLAY](ボイスディスプレイ)ボタン 19ページ [A.B.C./M.O.C.]ボタン 65、67ページ [MDR]ボタン 95ページ 9 ) ! @ [VOICE EDIT](ボイスエディット)ボタン 134ページ [PATTERN]ボタン 145ページ [SEQUENCE]ボタン 175ページ [U.
1 基本操作 B AS I C O P ER A T I O N ここでは、電源の入れ方や、画面の見方、エレクトーンの基本設定など、エレクトーンを使う上で必要となる基本事項 について説明します。 この章の内容 1 演奏までの準備 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4 ボイスディスプレイ . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2 画面の操作方法 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5 レジストレーションメニュー . . . . . . . . . . . . . . . . . . . . 21 • 画面のページを切り替える . . . . . . . . . . . . . . . . . . . . . . . 14 • ボタンを操作する . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 5 基 本 操 作 エクスプレッションペダルを右足で適度に踏み込みます。 エクスプレッションペダルでは、演奏中の音の強弱を調節します。 小さくなる 大きくなる 2 画面の操作方法 このエレクトーンの画面は、タッチパネルを搭載しています。画面上の設定/選択したい NOTE タッチパネルが汚れたら、柔ら かい布で乾拭きしてください。 項目に、直接触って操作できます。ただし、2か所以上の点を同時に操作することはできま せん。 また、ボリュームやリバーブなどの量を変更したい場合には、画面の右にあるデータコン トロールダイアルを使います。 先のとがったものや、爪などの 硬いもので、画面を操作しない でください。画面を傷つける おそれがあります。 ここでは、画面上での操作について、主なものを紹介します。 画面のページを切り替える ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 多くの画面では、画面の右上に数字などの書いてある楕円のボタンが表示されています。 このボタン表示を押すことで、ページを切
1 ボタンを操作する 基 本 操 作 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 画面に表示されるボタンを直接押すと、押したボタンが選択できます。そのほかに、オン/ オフを切り替えるタイプのボタン、リストを表示させるためのボタンがあります。 オン/オフを切り替えるボタン: オン オフ(ミュート: 消音) ボタンの色がグレーになります。 ボイスディスプレイの1ページ目で各音群のミュートを設定したり、リズムの画面でアカン パニメントの各パートをオン/オフしたり、ボイスエディットの画面で各エレメントの ミュートを設定したりする操作です。 リストを表示させるボタン: リストの中から目的のものを選ぶことができます。リスト右上の[閉じる]ボタンを押すと、 リストが閉じます。エフェクトタイプなどを選ぶときの操作です。 ELS-01/01C/01X 取扱説明書 15
1 スライダーを調節する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 基 本 操 作 ボリュームやリバーブなどの量は、画面上にスライダーで表示されます。画面に表示され たスライダーを直接触って値を変更するやり方と、データコントロールダイアルで値を変 更するやり方の2通りの操作法があります。大まかに値を変更したい場合には画面を触って 変更し、細かく変更する場合にはデータコントロールダイアルを使うと便利です。 スライダーを直接触る方法: 値を変更したい枠内を触ると、触った位置にスライダーが動き、値が変更できます。また、 スライダーのつまみ部分を指で触った状態で上下に動かすと、値が変更できます。 または 触った位置にスライダーが移動 つまみ部分を指で触った状態で 上下に動かす データコントロールダイアルを使う方法: 値を変更したいスライダーの上部(パラメーターの名前が書いてある部分)に触ると、その スライダーに青枠が移動します。この状態でデータコントロールダイアルを回すと、値を ひとつずつ増減
1 3 画面に関する基本設定 基 本 操 作 ここでは、エレクトーンを使う前に設定する以下の項目について説明します。 ● 画面に表示させる言語を選ぶ(日本語/英語) ● タッチパネルを操作するときの操作音を消す ● 画面の明るさを変える 画面に表示させる言語を選ぶ ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● エレクトーンの画面の表示言語は、初期状態で電源を入れたときには日本語に設定されて います。 必要に応じて表示言語を英語に切り替えることができます。(なお、この取扱説明書では、 表示言語は日本語で説明しています。) 1 [UTILITY]ボタンを押します。 ユーティリティ画面の設定ページが表示されます。 NOTE DISPLAY SELECT ユーティリティ画面の設定は、 A.B.C. M.O.C.
1 タッチパネルを操作するときの操作音を消す ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 基 本 操 作 初期状態で電源を入れたときには、タッチパネルを操作するたびに「ピッ」という音が鳴 るように設定されています。ステージで演奏するときなどは、この操作音を消すことがで きます。 1 2 [UTILITY]ボタンを押します。 ユーティリティ画面の設定ページが表示されます。 「タッチパネル操作音」の[OFF]ボタンを押すと、タッチパネルの操作音はオフ になります。 タッチパネル操作音 これ以降、タッチパネルを操作しても「ピッ」という音は鳴らなくなります。再び 操作音を鳴らしたいときは、手順2で[ON]を選んでください。 画面の明るさを変える ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 画面が明るすぎたり暗すぎたりして文字が見づらい場合には、画面の明るさを変えること ができます。部屋
1 4 ボイスディスプレイ 基 本 操 作 電源を入れたときに表示される画面がボイスディスプレイです。ボイスディスプレイでは、 各鍵盤に設定されているボイスや、リズム、右フットスイッチ(レジストレーションシフト) などのあらゆるデータを確認したり、各音群のミュート設定をしたりできる、エレクトー ンの最も基本的な画面といえます。 ここでは、ボイスディスプレイの見方を説明します。操作方法については、 関連ページ をご覧ください。 ボイスディスプレイを表示させるには: 電源を入れたときには必ずボイスディスプレイが表示されます。ほかの画面からボイス ディスプレイに移動する場合は、[VOICE DISPLAY]ボタンを押します。 DISPLAY SELECT VOICE DISPLAY A.B.C. M.O.C. MDR FOOT SWITCH UTILITY INTERNET RHYTHM PROGRAM VOICE EDIT PATTERN SEQUENCE U.ORGAN FLUTES L.
1 1 ボイス名表示 基 本 操 作 関連ページ ボイスを選ぶ(25ページ) 各音群に現在選ばれているボイス名が表示されます。また、それぞれのボイス名を押すこ とで、特定の音群だけをミュート(消音)することもできます。ボイス名を押すたびに、音が 出る状態とミュートとが切り替わります。 2 リズム名表示 関連ページ 現在選ばれているリズム名が表示されます。 リズムを選ぶ(54ページ) 3 A.B.C.モード表示 関連ページ A.B.C.
1 5 レジストレーションメニュー エレクトーンでは、上鍵盤、下鍵盤、ペダル鍵盤のボイスやリズムなどの組み合わせのこ とを「レジストレーション」といいます。REGISTRATION MENU (レジストレーション 基 本 操 作 NOTE レジストレーションメモリー 1 メニュー )の[1]〜[5]ボタンには、各ボタンにそれぞれ48種類(ELS-01)/60種類(ELS- 〜16にも、基本的なレジスト 01C/01X)ものレジストレーションがあらかじめ用意されており、いろいろなジャンルの レーションがプリセットされて います(83ページ)。 曲をすぐに演奏できます。 レジストレーションを選ぶ ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 1 REGISTRATION MENU (レジストレーションメニュー )の[1]〜[5]ボタンの いずれかを押します。 各ボタンには、それぞれ異なったジャンルのレジストレーションが含まれています。 演奏したい曲のジャンルにあわせて、それぞれのボタンを使
1 レジストレーションメニューリスト ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 基 本 操 作 画面番号 1 2 3 4 5 (ELS-01C/ 01X) 22 レジストレーションメニュー 1 キッズ レジストレーションメニュー 2 ポップス&ロック レジストレーションメニュー 3 ダンス&バラード レジストレーションメニュー 4 ジャズ&ラテン レジストレーションメニュー 5 シンフォニー &ワールド シンプル8ビート1 シンプル8ビート2 ダイナミック8ビート オルガンバラード ブローオンサックス ファンファーレ NYバラード ドラマチックバラード サックスアンサンブル ライトステップ ストリングオーケストラ ブリティッシュポップ ラブバラード ムーンライト ロマンチックバイオリン バロック サニーポップ 8ビートモダン スムースリード ビッグバンド キッズマーチ1 ロックバンド
1 6 バージョンを確認する 基 本 操 作 次の手順でエレクトーンのバージョンを確認できます。 1 2 [UTILITY]ボタンを押します。 ユーティリティ画面の設定ページが表示されます。 [バージョン]ボタンを押します。 画面に、バージョンを示すダイアログが表示されます。[OK]を押すと、ダイアログ が閉じます。 7 エレクトーンの初期化 すべてのデータをリセットして、エレクトーンを初期状態に戻すことができます。画面の 言語設定やタッチパネル操作音のオン/オフも含めたすべての情報をリセットします。すべ てのデータが消えてしまいますので、大切なデータはあらかじめスマートメディアなどに 保存しておきましょう。 レジストレーションを保存する (110ページ) 関連ページ インターネットダイレクト接続に関する設定だけは、この操作ではリセットされません。 209ページの方法で初期化をする必要があります。 1 2 関連ページ インターネット設定の初期化 (209ページ) いったん、エレクトーンの電源を切ります。 パネルの左下にあるENDING [1]ボタンを押しながら電源を入れます。 POW
2 ボイス(楽器音色) V O IC ES このエレクトーンには、400種類以上の多彩でリアルな楽器音色が内蔵されており、上鍵盤、下鍵盤、ペダル鍵盤の 2 どの鍵盤にも呼び出して演奏できます。これらの楽器音色のことを、「ボイス」といいます。上鍵盤では4つ、下鍵盤で は2つ、ペダル鍵盤では2つのボイスを重ねて鳴らすことができます。 上鍵盤の音群ボタン ( ボ イ ス 楽 器 音 色 ) 下鍵盤の音群ボタン ペダル鍵盤の音群ボタン この章の内容 1 各鍵盤で選べるボイス . . . . . . . . . . . . . . . . . . . . . . . . . 24 3 ユーザーボタンでボイスを選ぶ . . . . . . . . . . . . . . . . . . 30 2 ボイスボタンでボイスを選ぶ. . . . . . . . . . . . . . . . . . . . 25 4 ボイスリスト. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 • ボイスを選ぶ . . . . . .
下鍵盤ボイス 下鍵盤ボイス1、下鍵盤ボイス2の2つの音群があり、それぞれパネル上のLOWER 2 KEYBOARD VOICE 1、LOWER KEYBOARD VOICE 2のボタン群でボイスを選びます。 下鍵盤ボイス1 下鍵盤ボイス2 LOWER KEYBOARD VOICE 1 BRILLIANCE BRILLIANT BRASS WOODWIND TUTTI PAD SYNTH 1 PIANO ORGAN PERCUSSION GUITAR CHOIR WORLD 2 MELLOW LOWER KEYBOARD VOICE 2 VOLUME BRILLIANCE MAX STRINGS BRASS WOODWIND TUTTI PAD SYNTH 1 PIANO ORGAN PERCUSSION GUITAR CHOIR WORLD 2 MIN ボ イ ス 楽 器 音 色 VOLUME BRILLIANT MAX MELLOW MIN ( STRINGS ) ペダルボイス ペダルボイス1、ペダルボイス2の2つ
たとえば、PIANO (ピアノ)を選択した場合、画面にはいろいろな種類のピアノ音色 (ボイスメニュー )が表示されます。 2 ( ボ イ ス 楽 器 音 色 ) 2 ボイスメニューの中から、使用したいボイス名を押します。 ピアノにはたくさんの音が含まれているので、画面のボイス一覧の上に1、2、3と いう数字が表示されています。この数字を押すことで、現在表示されている以外の ピアノボイスを表示させて、選択できます。 ボイスを選択すると、選択されたボイス名はオレンジ色に変わります。これで 上鍵盤ボイス1には、ピアノ3が設定されました。 26 ELS-01/01C/01X 取扱説明書
音量を変える ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 2 音量を設定するには、音群のボリュームボタンを使う方法と、画面上で設定する方法があ ります。画面上のボリュームスライダーで設定する方が、音量を細かく設定できます。 ボ イ ス 楽 器 音 色 ( ボリュームボタンでの設定: それぞれの音群の右端にあるVOLUMEボタンを使用します。7段階の設定が可能です。 ) MIN (一番下)にすると、音は鳴りません。 UPPER KEYBOARD VOICE 1 BRILLIANCE STRINGS BRASS WOODWIND TUTTI PAD SYNTH 1 PIANO ORGAN PERCUSSION GUITAR CHOIR WORLD 2 VOLUME BRILLIANT MAX MELLOW MIN 画面上での設定: 画面上に現在表示されているボイスのボイスボタンをもう一度押すことで、(または、画面 上のボイスメニューで現在選ばれているボ
パネル上のボイスボタンを一度押すと、そのボイスのボイスメニューが画面上に表示さ れます。もう一度押すと、ボイスコンディション画面が表示されます。ボタンを繰り返 2 し押すと、ボイスメニューとボイスコンディション画面が交互に繰り返し表示されます。 UPPER KEYBOARD VOICE 1 STRINGS BRASS WOODWIND TUTTI PAD SYNTH 1 PIANO ORGAN PERCUSSION GUITAR CHOIR WORLD 2 VOLUME BRILLIANT MAX MELLOW MIN ( ボ イ ス 楽 器 音 色 BRILLIANCE ) ボイスコンディション画面にある[ボイスメニュー ]ボタンを押すことでも、ボイス メニューの表示に戻ります。 ボイスコンディション画面は、パンやエフェクト、ボリュームなど、ボイスに関する エレクトーンの電源を切ると、 パネル上や画面上で設定してい たデータはすべて消去されます。 データを消去したくない場合は、 電源を切る前に必ずレジスト レーションをスマートメディア などの外部メディアに保
SOLO(ソロ)機能 2 ほかの音群と異なり、リードボイス2には、ソロ機能があります。ソロ機能を使うこと によって、演奏中でも瞬時に上鍵盤をリードボイス2のみのソロ演奏に切り替えること ができます。 ( 1 ボ イ ス 楽 器 音 色 ソロ演奏したいボイスをリードボイス2の音群で設定します。 この状態では、上鍵盤ボイス1、2、リードボイス1、2すべての音群ボイスが 上鍵盤で鳴ります。 ) 2 リードボイス2の[SOLO (KNEE)]ボタンを押します。これで、ソロ機能が 待機状態になりました。 LEAD VOICE 2 3 VA VA ACOUSTIC VIRTUAL VA VA ELECTRONIC CUSTOM BRILLIANCE VOLUME BRILLIANT MAX MELLOW MIN 1 SOLO (KNEE) ニーレバーを立てます。 下げる 上鍵盤はリードボイス2で設定したボイスに切り替わり、リードボイス2 だけが上鍵盤で鳴るようになります。 4 演奏しながら、右足でニーレバーを右に押します。 この状態では、リードボイス2を除いた
3 ユーザーボタンでボイスを選ぶ 2 このエレクトーンには、パネル上のボイスボタン数よりはるかに多くのボイスが内蔵されて います。ここでは、それぞれの音群の全ボイス( VA音色以外)や、自分でエディットして作成 ボ イ ス 楽 器 音 色 ( したユーザーボイスを自在に使いこなせる便利なユーザーボタンについて説明します。 ユーザーボタンは、各音群の右側に2つまたは1つある、数字の書いてあるボタンです。 ユーザーボタンを使って、パネル上にボイスボタンがないボイスを選んでみましょう。 ) 1 使用したい音群のユーザーボタンを押します。 UPPER KEYBOARD VOICE 1 BRILLIANCE STRINGS BRASS WOODWIND TUTTI PAD SYNTH 1 PIANO ORGAN PERCUSSION GUITAR CHOIR WORLD 2 VOLUME BRILLIANT MAX MELLOW MIN ユーザーボタン 関連ページ 2 ボイスエディット(132ページ) 画面の上に表示される楽器のカテゴリーから、使用したい
ここで選んだカテゴリー (パーカッション)が、画面の左上に小さく表示されます。 この時点では、まだ実際にボイスが選択されていませんので、左上のカテゴリー名 2 と、その下に大きく表示されているボイス名は一致しません。 カテゴリーをすぐに選ぶには: ボ イ ス 楽 器 音 色 ユーザーボタンを押し続けたままで、自分の使用したいボイスボタン(どの音群でもよ ( い)を押すと、すぐにそのカテゴリーが選択できます。 1. ユーザーボタンを押しながら ) UPPER KEYBOARD VOICE 1 BRILLIANCE STRINGS BRASS WOODWIND TUTTI PAD SYNTH 1 PIANO ORGAN PERCUSSION GUITAR CHOIR WORLD 2 VOLUME BRILLIANT MAX MELLOW MIN 2.
4 ボイスリスト 2 内蔵されているボイスの一覧です。リストの左の数字は、画面上の数字と対応しています。 ELS-01/01C/01X共通 ボ イ ス 楽 器 音 色 ( STRINGS/VIOLIN (ストリングス/バイオリン) ストリングス1 ストリングス2 1 ) ストリングス3 ストリングス4 ストリングス5 ストリングス7 ストリングス8 ストリングス9 チェンバーストリングス1 2 チェンバーストリングス2 チェンバーストリングス3 チェンバーストリングス4 ピチカートストリングス2 ピチカートストリングス3 ピチカートストリングス4 トレモロストリングス ストリングス1&7 ストリングス2&ビオラ ストリングス3&4 3 3 ストリングス7&バイオリン5 オクターブストリングス1 オクターブストリングス2 バイオリン1 バイオリン2 バイオリン3 バイオリン4 4 4 バイオリン6 ビオラ チェロ1 ピチカートバイオリン 5 コントラバス1 コントラバス3 コントラバス4 6 アコースティックベース2 ピチカートベース1 ピチカートベース2 BRASS/TRUM
2 ポップリード5 アコーディオン3 エレクトリックギター 5 ポップリード6 アコーディオン4 ミュートギター ポップリード7 3 ダンスベース6 ダンスベース7 ダンスベース8 ジャズオルガン1 ディストーションギター 3 スムースベース1 シンセクラリネット3 ジャズオルガン2 バンジョー スムースベース2 シンセクラリネット4 ジャズオルガン3 シンセクラリネット5 ジャズオルガン4 ジャズオルガン5 シンセトランペット ジャズオルガン7 シンセバイオリン ジャズオルガン8 シンセブラス1 ジャズオルガン9 シンセブラス2 ポップオルガン1 シンセブラス3 ポップオルガン2 シンセブラス4 ポップオルガン3 シンセブラス5 ポップオルガン4 4 ロックオルガン1 シンセブラス8 ロックオルガン2 シンセブラス9 ロックオルガン3 シンセブラス10 オルガンベース1 シンセブラス11 オルガンベース2 シンセストリングス1 PIANO (ピアノ) シンセストリングス2 ピアノ1 シンセストリングス3 ピア
ELS-01C/01X共通 (VA音色) ボイス名 2 推奨音域 音色解説 VA ACOUSTIC (VAアコースティック) ( ボ イ ス 楽 器 音 色 1 V-フルート1 G2〜A6 ノイジーなフルート。高域ではアタック音が裏返ります。タッチトーンを増やし、アフタータッチをか けるとフラッター効果が得られます。 V-フルート2 C2〜C6 レガート奏法に適したフルート。ユーザービブラートを深めにセットすると効果的です。 V-オカリナ C3〜C6 ソフトなオカリナ風の音色です。 V-オーボエ C3〜F5 タッチでのダイナミックレンジが広いオーボエです。 V-クラリネット D2〜F5 V-ソプラノサックス A 2〜D5 ピアニッシモからフォルテッシモまで表現できるクラリネット。フォルテッシモでピッチが少し下がり 明るめの音色になります。 ) D 2〜G4 V-アルトサックス2 C2〜E4 V-テナーサックス1 A 2〜C4 V-テナーサックス2 C1〜G4 V-ブレスサックス1 A 2〜C4 柔らかめでジャズ向きのテナーサックス。レ
ボイス名 3 推奨音域 音色解説 C1〜C5 サックスをバイオリンの弓で擦ったような音色です。 V-クラビオリン G2〜G5 バイオリンと木管楽器の中間的な音色の仮想楽器です。 V-エアボウ C2〜G5 ノイズ混じりの擦弦系の音色です。 V-ワスピーホーン C1〜G4 金管楽器のマウスピースを木管楽器につけたような音色。アフタータッチでミュートの具合が変えられ ます。また、ホリゾンタルタッチでトランペットと同様の効果が得られます。 V-ミズホーン C1〜C6 ハーモニカとトランペットの中間のような仮想楽器です。 V-コスモミュート C1〜C5 タッチでミュート効果がかかるディストーション感のある金管楽器風音色です。 V-ファーゴ F1〜C7 バスーン風の音色。弱いタッチのときに高域ほどブレスノイズ感が強くなります。 2 ボ イ ス 楽 器 音 色 ( V-ボウ VA ELECTRONIC (VAエレクトロニック) E1〜E5 マイルドで温かみのある、ジャズテイストあふれるエレクトロニックギターです。 V-ピックドギター E1〜E5 ピックギター風の
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● AWM音源とVA音源 2 ELS-01C/01Xには、AWM (アドバンストウェーブメモリー )音源でつくられたボイスと、 ボ イ ス 楽 器 音 色 VA (バーチャルアコースティック)音源でつくられたボイスが内蔵されています。 ( VA音源は、リードボイス2の音群のボイス用に採用されており、AWM音源は、それ以外 のすべての音群のボイス用に採用されています。 ) AWM音源は、実際の楽器の音をサンプリングして、複雑な波形をデジタルデータとして 再現することで、リアルな楽器音をつくり出します。 それに対し、VA音源は先に仮想の楽器を本体内に設計し、その楽器に振動が伝わる様子を シミュレーションすることで音をつくり出します。この「仮想の楽器」のことを「物理モ デル」と呼びます。特にこのエレクトーンに用意されているボイスは、サックスやフルー トなどの管楽器をはじめ、ミュージックシーンで使用するさま
3 オルガンフルート(ELS-01C/01X) ORGA N F L U T ES ELS-01C/01Xにはオルガンフルート機能があり、多彩なスタイルのオリジナルオルガンサウンドをつくることができ ます。伝統的なオルガンと同じように、フッテージレバーで各フッテージのレベルを上げ下げしたり、パーカッシブサ ウンドを加えたりして、ゴージャスなフルオルガンサウンドが思いどおりにつくれます。9種類のフルートフッテージ と3種類のアタックフッテージを組み合わせて、さまざまなオルガンサウンドをつくってみましょう。 1 3 [U. ORGAN FLUTES]ボタン(上鍵盤のオルガンフルート)、または [L. ORGAN FLUTES]ボタン(下鍵盤のオルガンフルート)を押します。 オ ル ガ ン フ ル ー ト E L S 0 1 C / 0 1 X ボタンを押すとボタンのランプが点灯し、フルートフッテージの画面が表示されます。 なお、ELS-01にはオルガンフルート機能はないので、[U. ORGAN FLUTES]ボタ ンや[L.
4 右上の[アタック/ボリューム]ボタンを押してアタック/ボリュームページを表 示させ、全体の音量やアタック、ロータリースピーカーなどを設定します。 アタック/ボリュームぺ一ジ 3 6 ( オ ル ガ ン フ ル ー ト E L S 0 1 C / 0 1 X 1 2 3 4 5 - 1 アタック パーカッシブ音の設定をします。4'、2 2/3'、2'のレバーでは、それぞれのアタックフッ ) テージを設定します。 レングスのレバーでアタック音の長さを設定します。 2 レスポンス 鍵盤を弾いたときのレスポンス(応答)の速さを設定します。レスポンスのレバーを下に引く ほど、発音は遅くなり、パイプオルガンのような効果が得られます。 3 モード 弾いた鍵盤のどの音にアタックを付けるかを決定します。この設定は上鍵盤/下鍵盤で共通 です。 ファースト:最初に弾いた鍵盤の音にだけアタックが付きます。最初に弾いた鍵盤 を押さえている間は、アタックはほかの音には付きません。 イーチ:全部の音にアタックが付きます。 4 リバーブ 関連ページ リバーブ(46ページ) オルガンサウンドにかかるリ
6 エフェクトタイプ 関連ページ オルガンサウンドに固有の、ロータリースピーカー (トレモロ効果)の設定をします。エフェ クトタイプのボタンを押すと、ロータリースピーカーのエフェクトタイプ一覧が画面に表 示されます。一覧の中から使用したいエフェクトタイプを選び、画面右上の[閉じる]ボタン エフェクトリスト(53ページ) ロータリースピーカー (51ページ) を押して一覧表示を閉じます。選んだエフェクトタイプが設定されます。 3 ( オ ル ガ ン フ ル ー ト E L S 0 1 C / 0 1 X - エフェクトタイプを選びます もう一度、[U. ORGAN FLUTES]または[L.
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● オルガンフルート機能とパイプオルガン オルガンフルート機能は、伝統的なオルガンの構造をシミュレートしています。ここでは 簡単に、パイプオルガンと電気オルガンの仕組みについてご紹介します。 パイプオルガンは、鍵盤を弾くとその鍵盤につながれたパイプに空気が送られて、リード 3 のついたパイプから、正弦波に近い、「ポー」という縦笛のような音が出ます。素材や形状 の違うパイプがいくつもあり、その一本一本が、音色を構成する倍音を担当するという構 造になっています。これらのパイプにどれだけの空気を送るかを決める、「音栓(ストップ)」 オ ル ガ ン フ ル ー ト E L S 0 1 C / 0 1 X と呼ばれるレバーがあり、この音栓の組み合わせで、クラリネットやオーボエ、フルート のような音など、さまざまな音色を合成できるのです。このように合成された音は、教会 やホールの全体に反響し、重厚な音の広がりを持って演
4 コントロールとエフェクト V O IC E C O N T R OLS A ND EFFECT S ボイスコンディション画面やパネル上のボタンを使用して、選択したボイスに色々なコントロ一ルやエフェクトを加え て、多彩に変化させることができます。 また、ボイスによっては、あらかじめエフェクトが設定されているものもありますが、すべてお好みに応じて変更でき ます。搭載したエフェクトは、すべてデジタルエフェクトです。 下図は個々の音群に設定可能なコントロールやエフェクトのリストです。コントロール/エフェクトは種類によって かかり方が異なり、音群ごと、鍵盤ごと、そして楽器全体にかかるものがあります。 コントロール/エフェクト 設定方法 コントロール/エフェクトを設定できる音群 上鍵盤 ボ イ ス コ ン デ ィ シ ョ ン 画 面 で 設 定 ボ タ ン で 設 定 リードボイス 下鍵盤 ペダル鍵盤 上鍵盤ボイス1 上鍵盤ボイス2 オルガンフルート リードボイス1 リードボイス2 下鍵盤ボイス1 下鍵盤ボイス2 オルガンフルート ペダルボイス1 ペダルボイス2 パン 42ページ
1 ボイスコンディション画面で設定するもの パネル上のボイスボタンを二度続けて押すと(画面上に使用したいボイスがすでに表示され ている場合は一度だけ押すと)、画面上にボイスコンディション画面が現れます。 各ボイスにはそれぞれ4ページのボイスコンディション画面があり、画面右上の[1]〜[4] ボタンでページを切り替えます。 ボイスコンディション画面【ページ1】 4 1 コ ン ト ロ ー ル と エ フ ェ ク ト 1 2 3 2 2-1 2-2 3-1 3-2 4 5 6 7 2-1 2-2 3 3-2 4 5 6 8 ボイスコンディション画面の1ページ目では、パンやタッチトーン、ボリュームなどの、 ボイスの基本的な設定を行ないます。音群によって画面に表示される内容が異なります。 1 パン ステレオ出力による楽器音の左右の位置を決定します。音群ごとに、7か所の位置で設定で きます。 2 タッチトーン タッチトーンは、弾き方によって音量や音質を変化させる機能です。より豊かに、または より繊細に表現する力を発揮するもので、個々の楽器特有の微妙な表現が可能となります。 タッチト
3 ピッチ ピッチは、ホリゾンタルタッチやアフタータッチを使って、音程(音の高さ)を変えることの できる機能です。リードボイス2のVA音色については、音程だけでなく音色も変化するも のもあります。 3 - 1 ホリゾンタルタッチ (ELS-01C/01X) 上鍵盤または下鍵盤で、 鍵盤を押さえたまま左右に動かすこと(ホリゾンタルタッチ)によって、 音程をコントロールします。 鍵盤をより速く、大きく左右に動かすと、それだけ音程変化も速 く大きくなります。最大時で、 ±1オクターブの変化を得ることができます。タッチトーンと NOTE ELS-01C/01Xの画面上では、 ELS-01にない機能はスライダー 枠の色が濃くなっています。 の併用でユニークな演奏表現が可能となります。 レベルを0にするとホリゾンタルタッチはかからなくなり、レベルを上げると、ホリゾンタル 4 タッチによる変化幅が大きくなります。 ペダル鍵盤にはホリゾンタルタッチ機能はありません。 設定範囲:0〜14 3 - 2 アフタータッチ コ ン ト ロ ー ル と エ フ ェ ク ト 鍵盤を押さえつける強さ(アフタータッチ)によって、
ボイスコンディション画面【ページ2】 1 1 -1 3 4 1-2 1-3 1-4 コ ン ト ロ ー ル と エ フ ェ ク ト 2 3-1 3-2 4 5 リード音群とそれ以外の音群によって内容が異なります。スライド(3)は、リードボイス 1、2のみの設定です。 1 ビブラート ビブラートは、音色をふるわせてマイルドなイメージにします。音群ごとに設定できます。 ただし、まったくビブラートのかからないボイスや、設定したとおりにビブラートの効果 が得られないボイスもあります。 1 - 1 プリセット/ユーザー プリセットを選択すると、そのボイスにあらかじ ビブラートコントロール め設定された、最適なビブラートになります。 ディレイ スピード この場合、画面上のディレイ、デプス、スピード の各パラメーターは設定できません。 デ プ ス ユーザーを選択すると、画面上のパラメーター (ディレイ、デプス、スピード)を変更して、自分 のイメージにあったビブラートを設定できるよう になります。 1 - 2 ディレイ 鍵盤を押してからビブラートがかかるまでの時間の長さを決定します。レベルを上
3 スライド(リードボイスのみ) スライドは、レガートで演奏したときに、ポルタメント効果(続けて弾いた2つの音をなめ らかにつなげる効果)を加えます。リードボイスに、1オクターブの範囲内でかけることが 関連ページ リードスライドをコントロール する: ニーレバー (190ページ) できます。1オクターブ以上離れた音を弾いた場合には、スライドの効果はかかりません。 3 - 1 ON/ニ一レバー /OFF スライドのオン/オフ、 またはニーレバーでの設定を選択できます。 3 - 2 タイム スライド(ポルタメント)の速さを設定します。 レベルを上げると、スライド効果のスピードは 遅くなります。 設定範囲:0〜14 4 トランスポーズ 4 関連ページ 音群ごとに、音程を変える(移調する)ことができます。−6〜+6の範囲で、半音ずつ移調 できます。 5 チューン コ ン ト ロ ー ル と エ フ ェ ク ト トランスポーズ:楽器全体 (193ページ) 関連ページ より豊かな楽器表現力を得るために、音群ごとにピッチを少し上げ下げすることで音の厚 ピッチ:楽器全体(193ページ) みを増します
4 プリセットを選択すると、現在選ばれているボイスに最適なエフェクトが自動的に選ばれ ます。また、スルーを選択すると、エフェクトはかかりません。 コ ン ト ロ ー ル と エ フ ェ ク ト 2 タイプ1 (ページ3)/タイプ2 (ページ4) エフェクトのタイプ(種類)を選択します。タイプ1/タイプ2のボタンを押すと、選択してい るエフェクトカテゴリーに応じたエフェクトタイプ一覧が表示されます。その中から使用 したいエフェクトタイプを選び、画面右上の[閉じる]ボタンを押して一覧表示を閉じます。 エフェクトタイプを変更すると、下のエフェクトパラメーターも、選択されたエフェクト タイプに応じて、自動的に変更されます。 3 エフェクトパラメーター 選択しているエフェクトタイプに応じたパラメーターが表示されます。 2 パネル上のボタンで設定するもの リバーブやサステイン、ブリリアンス、そしてロータリースピーカーは、パネル上のボタ ンを使って、それぞれのページを画面上に呼び出して、設定します。 リバーブ ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
リバーブ画面【ページ1】 4 デプス: コ ン ト ロ ー ル と エ フ ェ ク ト リバーブの深さを調節します。パネル面のリバーブボタンは、このデプスの程度を表示し ているものです。パネル面のリバーブボタンでは7段階の調節ができますが、このページで NOTE タッチパネルやデータコントロールダイアルを使うことで、さらにきめ細かな設定が可能 デプスの値によっては、パネル です。 します。 上のREVERBボタンは2つ点灯 デプスの設定が0もしくはそれに近い状態の場合は、以下に述べる音群/種類ごとの設定で リバーブのかかる量を設定してもリバーブ効果は得られません。 設定範囲:0〜24 リバーブ画面【ページ2】 1 2 3 1 タイプ 各音群のボイスとオルガンフルート音色にかかるリバーブのタイプ(種類)を選択します。 ホール、ルーム、ステージなどさまざまなタイプのリバーブが選択できます。 関連ページ エフェクトリスト(53ページ) タイプボタンを押すことで、選択できるリバーブタイプの一覧が画面に表示されます。 ELS-01/01C/01X 取扱説明書 47
画面を切り替えます 4 画面上の[1]、[2]ボタンを押すことで画面を切り替えて、現在表示されてないエフェクト コ ン ト ロ ー ル と エ フ ェ ク ト タイプを表示させることもできます。一覧の中から使用したいリバーブタイプを選び、 画面右上の[閉じる]ボタンを押して一覧表示を閉じます。リバーブタイプを変更すると、 タイムは自動的に最適な値に変更されます。 2 タイム 各音群のボイスとオルガンフルート音色のリバーブの長さを設定します。レベルを上げる と、より長い設定となります。 設定範囲:0.3s〜30.
リバーブ画面【ページ4】 4 1 2 3 4 1 タイプ コ ン ト ロ ー ル と エ フ ェ ク ト 関連ページ リズムやアカンパニメント、キーボードパーカッション、マイク入力にかかるリバーブの マイクやギターをつないで使う (217ページ) 種類を選択します。 2 タイム リズムやアカンパニメント、キーボードパーカッション、マイク入力にかかるリバーブの 長さを設定します。 設定範囲:0.3s〜30.
サステイン ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 関連ページ ニーレバー (188ページ) サステインは、鍵盤から指をはなしたあとに音に余韻を与える効果です。上鍵盤/下鍵盤/ ペダル鍵盤のそれぞれに対して、オン/オフしたりサステインの長さを調節したりできま す。 また、ニーレバーを使ってサステインのオン/オフを切り替えることもできます。サステイ ンはリードボイスにはかかりません。 サステインを設定するには: SUSTAIN パネル上の左端にあるSUSTAIN (サステイン)ボタンを押します。画面上 4 UPPER (KNEE) にサステインレングス画面が現れます。 サステインボタンを押すと、ボタンの真上のランプが点灯し、サステイン コ ン ト ロ ー ル と エ フ ェ ク ト LOWER (KNEE) PEDAL がオンの状態であることを示します。もう一度押すことで、ランプは消え、 サステインはオフになります。ランプが消えた状態ではサステインはかか りませんので、演奏前には
ロータリースピーカー ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ロータリースピーカーは、スピーカーを回転させて得られるような、豊かで広がりのある 効果(トレモロ効果)をつくり出すエフェクトです。パネル上の[ROTARY SP SPEED]ボタ ンや、左のフットスイッチを使って、演奏中もリアルタイムで効果をオン/オフできます。 ロータリースピーカーは、パネル面の[ROTARY SP SPEED]ボタンをオンにするだけで は、効果は得られません。以下の手順で設定する必要があります。 1 トレモロ効果をかけたい音群、またはオルガンフルート音色で、エフェクトに 4 ロータリースピーカーを選択します。 各音群のボイスにロータリースピーカーを設定する場合は、ボイスコンディション 画面の3ページ目にあるエフェクト1ボタン、または4ページ目にあるエフェクト2 コ ン ト ロ ー ル と エ フ ェ ク ト ボタンで設定します。詳しくは45ページをご覧ください。 ここでロータリースピーカーを選択します
ロータリースピーカー画面 DISPLAY SELECT VOICE DISPLAY A.B.C. M.O.C. MDR FOOT SWITCH UTILITY INTERNET RHYTHM PROGRAM VOICE EDIT PATTERN SEQUENCE 4 U.ORGAN FLUTES L.ORGAN ROTARY SP SPEED FLUTES 1 コ ン ト ロ ー ル と エ フ ェ ク ト 2 1 スピード ロータリースピーカーの回転するスピードを調節します。 設定範囲:2.69Hz〜39.7Hz 2 モード パネル上の[ROTARY SP SPEED]ボタンがオフのときのロータリースピーカーの状態を 設定します。スローを選択すると、ロータリースピーカーの回転が遅く(0.
3 エフェクトリスト リバーブ(ホールなどの残響感を与え、サウンドに奥行きや広がりを付加します。) ホール1 ホール2 ホール3 ホールM ルーム1 ルーム2 ルーム3 ルーム4 ホールL ルームS ルームM ルームL ステージ1 ステージ2 プレート1 プレート2 ホワイトルーム トンネル キャニオン ベースメント XGホール1 XGホール2 XGルーム1 XGルーム2 XGルーム3 XGステージ1 XGステージ2 XGプレート GMプレート ディレイ(音声信号を遅らせることで、時間差をおいて繰り返しエコー効果が得られます。) ディレイLCR XGディレイLCR ディレイLR テンポディレイ テンポエコー テンポクロス エコー クロスディレイ リバースゲート カラオケ1 4 アーリー /カラオケ(カラオケのようなエコーを与えます。 ) アーリー 1 アーリー 2 カラオケ2 カラオケ3 ゲートリバーブ コ ン ト ロ ー ル と エ フ ェ ク ト コーラス(複数の音が同時に鳴っているような効果が得られ、サウンドに奥行
5 リズム/キーボードパーカッション R H Y T H M / K E Y B O A R D P E R C U S S I O N このエレクトーンには、実際のドラムやパーカッションサウンドをサンプ KEYBOARD PERCUSSION リングして作成された274種類のリアルなリズムパターンが内蔵されて 1 2 SEQ. SEQ. 1 2 SEQ. SEQ.
2 リズムメニューの中から、使用したいリズム名を押します。 ポップスにはたくさんのリズムが含まれているので、画面のリズム一覧の上に1、 2、3、4という数字が表示されています。この数字を押すことで、現在表示されて いる以外のポップスのリズムを表示させて、選択できます。 5 リズムを選択すると、選択されたリズム名はオレンジ色に変わります。 リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン リズムの構成 演奏を盛り上げるために、ひとつのリズムの中にも「セクション」と呼ばれるリズムパ ターンのバリエーションが用意されています。セクションはリズムの再生中に自由に切 り替えることができます。 イントロ 曲の始まりに適したセクションです。3つのイントロセクションがあり、INTRO [1]〜 [3]ボタンで選びます。小節数はリズムによって違い、イントロの演奏が終了すると自 動的にメインに移ります。 INTRO 1 2 3 選ばれているイントロセクションが点灯 メイン 曲のメイン部分の演奏で使う、基本のリズムパターンです。4つのメインセクションが あり、MAIN/FILL IN (メイン/
フィルイン 曲の流れに区切りをつけて演奏を盛り上げる、1小節のリズムパターンです。4つの フィルインセクションがあり、点灯しているMAIN/FILL IN [A]〜[D]ボタンをもう 一度押すと、フィルインが再生します。1小節のフィルインパターンを再生したあと は、自動的にメインに移ります。 MAIN / FILL IN A B C D 再生中のフィルインセクションが点滅 ブレイク リズムに一時的な空白部分を入れることでメリハリをつける効果を持つ、1小節のリズ ムパターンです。[BREAK]ボタンを押すと、ブレイクが再生します。1小節再生した 5 あとは、自動的にメインに移ります。 START SYNCHRO START リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン BREAK ブレイクが選ばれているときに点灯 エンディング 曲の終わりに適したセクションです。小節数はリズムによって違い、エンディングの 演奏が終了すると自動的にリズムはストップします。3つのエンディングセクションが あり、ENDING [1]〜[3]ボタンで選びます。 ENDING 1 2 3
イントロ INTRO 自動的に数小節イントロを入れてからリズムをスタートさせ 1 2 3 ます。INTRO [1]〜[3]ボタンのいずれかを押したあと、 [START]または[SYNCHRO START]ボタンを押してリズム をスタートさせます。 イントロが演奏されている間、BAR/BEAT (バー /ビ一ト) BAR / BEAT 表示は、マイナス表示で逆にカウントします。 NOTE TEMPO イントロ、エンディングの再生中 は、下鍵盤を弾いても音は鳴りま エンディング ENDING リズムをストップするときに、自動的に 数小節エンディング 1 2 せん。 3 パターンを入れます。 NOTE リズムを再生しているときにENDING [1]〜[3]ボタンのいず メインセクション再生中に れかを押すと、エンディングパターンが入ったあとで、リズムは自動的に終了します。 ENDING [1]ボタンを押すと、 5 エンディング1が鳴る前に自動的 エンディングが演奏されている間に、再度同じENDINGボタンを押すと、テンポが徐々に に1小節フィルインが入ります。
ブレイクを入れるには: リズムを使用して演奏しながら、ブレイクを入れたいところで[BREAK]ボタンを押します。 START SYNCHRO START BREAK このほかに、フットスイッチを使ってリズムをスタート/ストップしたり、セクションを 切り替えたりすることもできます。詳しくは、186ページをご覧ください。 リズムの音量を変える 5 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 音量を設定するには、リズムのボリュームボタンを使う方法と、画面上で設定する方法が あります。画面上で設定する方が、音量を細かく設定できます。 リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン ボリュームボタンでの設定: RHYTHM (リズム)の右端にあるVOLUMEボタンを使用します。7段階の設定が可能です。 MIN (一番下)にすると、音は鳴りません。 RHYTHM VOLUME MAX SEQ. SEQ. 1 2 SEQ. SEQ.
リズムのテンポを変える ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● TEMPO (テンポ)ダイアルを回して、リズムの速さを変更できます。時計回りに回すと 速くなり、逆に回すと遅くなります。 TEMPO テンポが 遅くなる テンポ表示の場合 テンポが 速くなる BAR / BEAT TEMPO 設定されているリズムの速さ(テンポ)は、テンポダイアルの右の画面に、数字で表示されま す。表示される数字は、1分間の拍数を表します。 設定範囲:40〜240 5 リズムの再生中には、テンポ表示は自動的にバー /ビート表示に切り替わります。 リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン バー/ビート表示の場合 BAR / BEAT TEMPO 小節 拍 バー /ビート表示のときには、画面内の左の数字は現在の小節を表し、右の数字は小節内の 拍数を表します。 テンポやバー /ビートは、ボイスディスプレイでも確認できます。ボイスディスプレイは、 テンポとバー /ビート表示を同
それぞれのリズムには、あらかじめリズムごとに設定されたテンポ(プリセットテンポ)が あります。プリセットテンポに戻したい場合は、リズムメニュー画面の右下にある[テンポ 初期設定]ボタンを押します。 5 リズムのリバーブを設定する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン 関連ページ リバーブ(46ページ) リズムコンディション画面で、リズムや打楽器音にかかるリバーブ(パーカッションリバー ブ)の量を調節できます。 DATA CONTROL ここでリバーブを最大にしても、パネル上のリバーブ量を上げないと、リバーブ効果は得 られません。 設定範囲:0〜24 60 ELS-01/01C/01X 取扱説明書
2 ユーザーボタンでリズムを選ぶ リズムボタンの右側にあるユーザーボタンを使うことで、リズムメニューのすべてのリズ ムだけでなく、リズムパターンプログラムでつくったユーザーリズムも選択できます。 また、同一カテゴリー内の異なったリズムをパネルに呼びだしておきたいときに、1つは リズムボタンに、もう1つはユーザーボタンに呼びだしておくと、すぐに切り替えができて 便利です。 1 リズムボタンの右側にあるユーザーボタンを押します。 RHYTHM VOLUME MAX SEQ. SEQ. 1 2 SEQ. SEQ.
3 リズムリスト 下表のとおり、リズムは全部で274パターンあります。リストの左の数字は、画面上の数字と対応しています。 MARCH (マーチ) アコースティックジャズ フィンガーピッキン ライトサンバ1 マーチングバンド1 ミディアムジャズ ハートビート ライトサンバ2 マーチングバンド2 ファストジャズ ギターポップ ポップサンバ1 マーチングバンド3 コンボスイング ブリティッシュ 16ビート 5 リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン 16ビート1 ボサノバ1 ライトスイング 16ビート2 ボサノバ2 6/8マーチ2 アフロキューバン1 16ビート3 ボサノバ3 6/8キッズ アフロキューバン2 16ビート4 ポップボサ 6/8オルガンマーチ ビバップ フュージョンシャッフル1 マンボ1 ブロードウェイ ファイブフォー フュージョンシャッフル2 マンボ2 SFマーチ ジャズバラード1 ジャズポップ サルサ1 ワイルドウエスト ジャズバラード2 16ビートシャッフル1 サルサ2 バロック
2 ホーダウン ロックンロール2 カントリー 2/4 スキッフル カントリーシャッフル ベースを加えて盛り上げるような音楽を表現するため ハワイアン ジャイブ につくられたものがあります。 メキシカンダンス ブギーウギー DANCE (ダンス) イビサ1 ンドラム、アドドラム)がなくアカンパニメントだ ドラマチックバラード イビサ2 けになっています。アカンパニメントをオンにし ムービーバラード1 ユーロトランス た状態で使用してください。 ムービーバラード2 ディスコティーンズ シークレットサービス テクノパーティー カーペンターズポップ 1 クラブダンス ロマンチックバラード ドリームダンス ラブソング クラブハウス カテゴリー MARCH USディスコ スイングハウス イージーバラード USポップ ギターバラード1 USヒップホップ ギターバラード2 クラシックヒップホップ ギターバラード3 トリップホップ 2 チャートポップ リズム名 セクション 6/8オルガンマーチ メインA、メインB バロック イントロ1
4 自動伴奏をつける:アカンパニメント アカンパニメントは、リズムと連動して、多彩な装飾音を施した伴奏パターンが得られる機 能です。アカンパニメントは、リズムメニューとリズムコンディション画面で設定します。 1 パネル上の使用したいリズムのボタンを押します。 5 リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン アカンパニメント 画面下部に、リズムを構成する各パートのボタンがあります。ドラム以外のパート をまとめて「アカンパニメント」といいます。 2 鳴らしたいアカンパニメントのパートをオンにします。 アカンパニメントは、コード1、コード2、パッド、フレーズ1、フレーズ2の5つの パートで構成されており、それぞれのパートをオン/オフさせることができます。 すべてのパートをオフにすると、アカンパニメントは鳴りません。 コード1/コード2: コード伴奏を担当する、ピアノやギターなどの演奏を再生するパートです。 パッド: ストリングスやオルガンなどの演奏を再生するパートです。 フレーズ1/フレーズ2: アルペジオや、パンチの効いたブラスフレーズなどを再生するパートです。アカン パニ
3 アカンパニメントのボリュームやリバーブを調節します。 選んだリズムボタンをもう一度押して、リズムコンディション画面を表示させます。 右側2つのスライダーで、画面に直接触ったりデータコントロールダイアルを使った りして、アカンパニメントの音量とリバーブを設定します。 DATA CONTROL 5 リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン ベースパターンをつける: 5 オートベースコード (A.B.C.) オートベースコード(A.B.C.)は、リズムと連動し、演奏に合わせて自動的にベースの伴奏が 得られる機能です。選ばれているリズムに合わせて、ベースのパターンが自動的に選択さ れます。オートベースコードには、3種類のモードがあります。 オートベースコードを使用するためには、ペダルポリモードをオフにしておいてください。 ペダルポリモードがオンの状態では、オートベースコードのベース伴奏は鳴りません。 関連ページ ポリ(43ページ) オートベースコードを設定するには: [A.B.C./M.O.C.
1 A.B.C.
2 メモリー 下鍵盤: オンにすると、リズムが鳴っている間は、下鍵盤から指をはなしても下鍵盤の音が鳴り続けます。 ペダル鍵盤: オンにすると、リズムが鳴っている間は、 ペダル鍵盤から足をはなしても、ペダル鍵盤の音が 鳴り続けます。 シングルフィンガーやフィンガードコードの場合は、 オンにしてリズムをスタートすると、下 鍵盤から指をはなしたあともペダル鍵盤の音が鳴り続けます。 オートベースコードを使って、 リズムをシンクロスタートで始める場合は、下鍵盤/ペダル鍵 盤のメモリーをオンにしてください。 メモリーをオンにしないで使用した場合は、演奏中に 下鍵盤から指をはなすと、 リズムもストップします。 5 メロディにハーモニーをつける: メロディオンコード (M.O.C.) 6 リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン 下鍵盤で弾いたコードによって、上鍵盤で弾くメロディラインに自動的にハーモニーを付 ける機能です。メロディオンコードには、3つのモードがあります。また、メロディオン コードをニーレバーでオン/オフすることもできます。 メロディオンコードを設定するには: [A.B.
モード2: メロディに近い音域で最高3音までの付加音がハーモニーとなって得られます。 モード3: メロディから比較的離れた音域で最高4音までの付加音がハーモニーとなって得られます。 2 ニーレバー 関連ページ メロディオンコードをコント ロールする(189ページ) メロディオンコードをニーレバーでコントロールするためのオン/オフスイッチです。モー ドを選択したあと、ここでの設定をONにすると、ニーレバーでメロディオンコードのオン /オフ切り替えができるようになります。 上鍵盤の音群で、音量が0の場合はメロディオンコードの効果は得られません。また、リー ドボイスに対してはメロディオンコードの効果はかかりません。 5 鍵盤で打楽器を演奏する: 7 キーボードパーカッション リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン ドラム系やラテンパーカッション系、そして和太鼓などのバラエティあふれる打楽器音を 鍵盤に呼びだして、リアルタイムでパーカッション演奏が楽しめます。 このキーボードパーカッションには、各鍵盤にあらかじめ打楽器音を割り当ててあり、す ぐにパーカッション演奏ができるプリセ
3 パーカッションのキットを選択します。 初期設定ではELキットが選ばれていますが、そのほかに全部で16種類のキットが 選択できます。キットボタンを押すと、パーカッションキットの一覧が画面上に表 示されます。この中から使用したいキットを選びます。画面右上の[閉じる]ボタンを 押すと、一覧表示が閉じます。 5 各キットにどんな打楽器が割り当てられているかは、70ページのプリセットキー ボードパーカッションリストをご覧ください。 リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン キットを変更するときに、「アサインとセットアップを消去しますか?」というメッセー ジが表示されることがあります。[消去]を選ぶと、アサインページと設定ページの内容 がすべて初期化され、選択したキットを初期状態でパネル上に呼び出します。 [キャンセル]を選ぶと、アサインとセットアップを消去せずに選択したキットをパネル 上に呼び出します。 4 リバーブや音量を設定します。 キーボードパーカッション画面のリバーブスライダーとボリュームスライダーで、 リバーブと音量を調節します。 DATA CONTROL ここでの
プリセットキーボードパーカッションリスト ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ELキット プリセット2(ペダル鍵盤) C1 C 1 プリセット1(下鍵盤) バスドラムヘビー - キック - プリセット1(上鍵盤) - サイドスティック スルドミュート - スネア スルドオープン スネアブラッシュショット1 クラベス ハンドクラップ ハイQ E1 スネアドラムリバーブ1 - スネアタイト ホイップスラップ F1 スネアドラムライト - フロアタムL スクラッチH タム3 シンセタム3 ハイハットクローズ スクラッチL スネアドラムリム1 コンサートバスドラム フロアタムH フィンガースナップ タム2 シンセタム2 ハイハットペダル クリックノイズ ハイハットクローズ バスドラムヘビー ロータム メトロノームクリック タム1 シンセタム1 ハイハットオープン
SFXキット1 SFXキット2 プリセット1(下鍵盤) プリセット2(ペダル鍵盤) プリセット1(上鍵盤) プリセット1(下鍵盤) プリセット2(ペダル鍵盤) プリセット1(上鍵盤) カッティングノイズ1 - フォーンコール - カッティングノイズ2 - ドアのきしみ - - - ドアを閉める - ストリングスラップ - スクラッチカット - - - スクラッチH3 - - - ウィンドチャイム - - - 電話 - - - - - - - - - - - - - - - - - B1 - - - - C2 - - - - - - - - - - - - - - - - - - - - - - - - E2 フルートキークリック - - イグニッション - - F2 - - - タイヤ - - - - - レーシングカー - - - - - 衝突 - - - - - - - - -
アラビックキット ポップラテンキット プリセット1(下鍵盤) プリセット2(ペダル鍵盤) プリセット1(上鍵盤) プリセット1(下鍵盤) プリセット2(ペダル鍵盤) プリセット1(上鍵盤) キックソフト - ボンゴH Op.1f - サイドスティック - ボンゴH Op.3f - スネアソフト - ボンゴHリム - アラビックハンドクラップ - ボンゴHチップ - スネアドラム - ボンゴHヒール - フロアタムL - ボンゴHスラップ - ハイハットクローズ - ボンゴL Op.1f ハンドクラップ フロアタムH - ボンゴL Op.
ユーザーキーボードパーカッションを設定する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 上鍵盤、下鍵盤、ペダル鍵盤のどのキー (鍵)にでも、好きな打楽器を割り当てられます。 打楽器を割り当てたセットは、ユーザー 1〜ユーザー 8に保存でき、パネル上の KEYBOARD PERCUSSION [1]または[2]ボタンで呼び出します。 ここでは、ユーザー 1に打楽器を割り当て、パネル上の[1]ボタンで呼び出す手順を例とし て使用します。 1 パネル左端のKEYBOARD PERCUSSION (キーボードパーカッション)の [1]ボタンを押します。 画面上にキーボードパーカッションのメニューページが表示されます。 2 画面で[ユーザー 1]を選択します。 5 これで、次にキーボードパーカッションの[1]ボタンを押したときには鍵盤にユー ザー 1が呼び出せるようになりました。 3 リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン パーカッションのキットを選択します。 キットの
6 打楽器を任意の鍵盤に割り当てます。 打楽器メニューの中で使用したい打楽器名を押しながら、その打楽器音を割り当て たい鍵盤を押します。 打楽器を割り当てる鍵盤名 打楽器名 NOTE ユーザーキーボードパーカッ ションは、ユーザー 1〜8に (合計で8セット)設定できます。 ただし、レジストレーションご とには設定できません。レジス トレーションに設定できるのは、 キーボードパーカッションのオ 鍵盤を押します ン/オフとメニュー (プリセット 5 1〜2/ユーザー 1〜8)情報のみ です。 リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン 打楽器名を押しながら...
はじめからやり直したいときは: アサインページの[消去]ボタンを使って、入力した打楽器音をすべて消去できます。 1 [消去]ボタンを押して、すぐに画面から指をはなします。以下の画面が表示さ れ、全音消去するかどうか確認を求めてきます。 5 2 リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン [消去]ボタンを選択すると、全音消去を実行し、画面上に「すべてのアサイン を消去しました!!」という操作完了のメッセージが一時的に表示されます。 [キャンセル]ボタンを選択すると、操作をキャンセルし、前の画面に戻ります。 キーボードパーカッションをコピーする ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● プリセットキーボードパーカッションや、すでに作成してあるユーザーキーボードパー カッションを、別のユーザーにコピーして、それをもとに新しいユーザーキーボードパー カッションをつくることができます。ここでは、プリセット1をユーザー 1にコピーする場 合を例に説明します。 1 パネル左端の
5 3 コピー先にしたいユーザー (ここではユーザー 1)を選択します。 4 [コピー元]ボタンを押します。コピー元を選択する画面が表示されます。 リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン 5 6 コピーしたいキーボードパーカッション(ここではプリセット1)を選びます。 プリセット1をコピーするかどうか確認を求める画面が表示されます。 [コピー ]ボタンを選択すると、プリセット1のコピーを実行し、画面上に 「プリセット1をコピーしました!」という操作完了のメッセージが一時的に表示 されます。 [キャンセル]ボタンを選択すると、操作をキャンセルし、前の画面に戻ります。 76 ELS-01/01C/01X 取扱説明書
各打楽器の細かい設定をする ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 各打楽器について、パンやボリューム、リバーブなどを設定したり、ドラムのチューニン グを変更したりして、自分の好みの打楽器音をつくることができます。ここでの設定は、 楽器全体で1つなので、レジストレーションごとに設定を変えることはできません。 1 設定したい打楽器音が割り当てられている鍵盤の、音群のボリュームを0にして 2 キーボードパーカッション画面で画面右上の[設定]ボタンを押します。 3 おきます。 キーボードパーカッションの設定ページが表示されます。 5 設定を変えたい打楽器が割り当てられている鍵盤を押します。 画面に打楽器名が表示され、その打楽器について細かい設定を行ないます。 リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン 現在選ばれている 打楽器名 1 2 3 4 5 6 1 パン 現在選ばれている打楽器のステレオ出力による位置を設定します。7か所の位置で、打楽器 ご
6 初期化 現在選ばれている打楽器の、パンやピッチ、リバーブなどの設定を、すべて初期設定に戻 します。 [実行]ボタンを押すと、以下の画面が表示され確認を求めてきます。 5 [実行]ボタンを選択すると、初期設定に戻ります。この場合、画面上に「初期化しました!!」 が一時的に表示され、操作が完了したことを示します。 リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン [キャンセル]ボタンを選択すると、操作を中止し、前の画面に戻ります。 78 ELS-01/01C/01X 取扱説明書
キットアサインリスト ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ELキット スルドオープン スネアロール ハイハットオープン シンバル スルドミュート サイドスティック ハイハットクローズ クラッシュシンバル1 スルドリム オープンリムショット ハイハットペダル クラッシュシンバル2 スルドモフ ブラッシュタップ スネアドラム クラッシュシンバルミュート ティンバレス/カウベル ブラッシュスラップ スネアショート ライドシンバル1 ティンバル1ハイ ブラッシュスワール スネアタイトH ライドシンバル2 ティンバル1ロー ブラッシュタップスワール スネアソフト2 ライドシンバルカップ ティンバル2ハイ タム スネアロール オーケストラシンバル ティンバル2ロー フロアタムL サイドスティックライト オーケストラシンバルロール ティンバル3ハイ フロアタムH オープンリムショット
ヒットキット メトロノームクリック スクラッチL パーカッション4 シンバル メトロノームベル SeqクリックL ハイQ SeqクリックH クリックノイズ クラッシュシンバル1 5 リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン 80 クラッシュシンバル2 ルームキット メトロノームクリック スクラッチH スプラッシュシンバル シンバル メトロノームベル スクラッチL チャイニーズシンバル クラッシュシンバル1 ライドシンバル1 クラッシュシンバル2 ロックキット SeqクリックH ライドシンバル2 スプラッシュシンバル シンバル メトロノームクリック ライドシンバルカップ チャイニーズシンバル クラッシュシンバル1 メトロノームベル ハイハットオープン2 ライドシンバル1 クラッシュシンバル2 ハイハットクローズ2 ライドシンバル2 スプラッシュシンバル エレクトロキット ハイハットペダル2 ライドシンバルカップ チャイニーズシンバル シンバル スネアドラム ハイハットオープン ライドシンバル1
ホイップスラップ ウッドブロックH ベルツリー パーカッション3 フィンガースナップ ウッドブロックL トライアングルオープン タンバリン ハンドクラップ スティック トライアングルミュート カスタネット パーカッション4 ホイップスラップ ダンスパーカッション3 ジングルベル ハイQ フィンガースナップ ダンスパーカッション4 ベルツリー クリックノイズ ハンドクラップ スネアダンス1 トライアングルオープン スクラッチH パーカッション4 ホイップスラップ トライアングルミュート スクラッチL ハイQ フィンガースナップ ウッドブロックH SeqクリックL クリックノイズ ダンスクラップ ウッドブロックL SeqクリックH スクラッチH パーカッション4 スティック メトロノームクリック スクラッチL ハイQ ホイップスラップ メトロノームベル SeqクリックL クリックノイズ フィンガースナップ SeqクリックH スクラッチダンス1 ハンドクラップ アナログキット メトロノームクリック スクラッチダ
5 リ ズ ム / キ ー ボ ー ド パ ー カ ッ シ ョ ン アゴゴL カバサ アラビックキット コンガL オープン サンバホイッスルH シェーカー アラビック1 コンガL ミュート サンバホイッスルL アゴゴH ナカラザンドム コンガL スラップOp. パーカッション3 アゴゴL ナカラザンエッジ コンガL スラップ タンバリン サンバホイッスルH ハゲールドム コンガL スライド カスタネット サンバホイッスルL ハゲールエッジ ボンゴ ジングルベル パーカッション3 ザグロウダH ボンゴH Op. 1f ベルツリー タンバリン ザグロウダL ボンゴH Op.
6 レジストレーションメモリー RE G IST R A T I O N M EM O R Y エレクトーンのパネル上、または画面上で設定したボイスやリズムなどのセッティング(=レジストレーション)は、 上鍵盤と下鍵盤の間にある1〜16までのナンバーボタンに記録できます。記録したレジストレーションは簡単に呼び出 すことができます。この機能を「レジストレーションメモリー」と呼びます。記録したレジストレーションは、演奏中 にナンバーボタンを押して呼び出すだけでなく、あらかじめプログラムしておいてフットスイッチを使って呼び出すこ とも可能です。レジストレーションメモリーに記録したレジストレーションは、スマートメディアなどの外部メディア に保存することもできます。 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 D 1〜16のナンバーボタンには、あらかじめ用意された基本的なレジストレーションがセットされています。 自分で設定したレジストレーションをナンバーボタンに記録すると、そのナンバーボタンに入っていたレジストレー ションは上書きされて消えてしま
メモリーできない機能 以下の設定は、楽器全体に関する設定なので、レジストレーションメモリーに記録して おくことはできません。また、スマートメディアなどに保存することもできません。 ・ピッチ(193ページ) ・MIDIコントロール(225ページ) ・マイクボリューム(218ページ) ・マイクリバーブ(218ページ) ・画面に関する設定(17ページ) ・インターネット環境設定(205ページ) 以下の設定は、レジストレーションナンバーごとに違う設定にすることはできません。 関連ページ レジストレーションを保存する (110ページ) ソングのレジストレーションデータとして、スマートメディアなどに保存できます。 ・トランスポーズ(193ページ) ・オルガンフルート音色のアタックのモード(38ページ) ・レジストレーションシフト(87ページ) ・オートフィル(57ページ) 6 ・リバーブタイプ(47ページ) ・ユーザーボイス(142ページ) ・ユーザーリズム(168ページ) レ ジ ス ト レ ー シ ョ ン メ モ リ ー ・ユーザーキーボードパーカッション(73ページ) ・リズムシーケンス(175ページ)
2 レジストレーションを呼び出す 呼び出したいナンバーボタンを押すだけで、記録したレジストレーションをパネル上に呼 び出せます。 ● 手でボタンを押すのではなく、フットスイッチを使ってレジストレーションを呼び出す 方法(レジストレーションシフト)もあります。レジストレーションシフトについては87 ページをご覧ください。 ● リズムシーケンスの一部として、あらかじめレジストレーションの変更をプログラムし ておく機能(レジストレーションシーケンス)もあります。レジストレーションシーケン スについては180ページをご覧ください。 ディスエーブルボタンについて: 6 ナンバーボタンを押してレジストレーションを切り替えると、リズムも同時に変わりま す。しかし、レジストレーションメモリー右端の[D.
3 記録したレジストレーションを 外部メディアに保存する 関連ページ レジストレーションを保存する (110ページ) スマートメディアなどの外部メディアに、レジストレーションを保存できます。レジスト レーションメモリーに記録してある16レジストレーションをまとめて、ソングに保存し ます。 MDR機能(外部メディアへのデータ保存や外部メディアのデータ読み込み)については、第 7章で詳しく説明しています。ここでは、スマートメディアにレジストレーションを保存す る手順を、簡単に説明します。 1 2 スマートメディア挿入口に、スマートメディアを差し込みます。 [MDR]ボタンを押します。 MDR画面が表示されます。 DISPLAY SELECT 6 レ ジ ス ト レ ー シ ョ ン メ モ リ ー VOICE DISPLAY A.B.C. M.O.C. MDR FOOT SWITCH UTILITY INTERNET RHYTHM PROGRAM VOICE EDIT PATTERN SEQUENCE U.
4 レジストレーションメモリーの初期化 レジストレーションメモリーに記録されたレジストレーションを消去し、レジストレー ションメモリーを初期状態に戻すことができます。この場合、すべてのレジストレーショ ンデータが消去されてしまいます。大切なデータは、あらかじめスマートメディアなどの 外部メディアに保存しておきましょう。 1 関連ページ エレクトーンの初期化 (23ページ) [UTILITY]ボタンを押して、ユーティリティ画面の設定ページを表示させます。 DISPLAY SELECT VOICE DISPLAY A.B.C. M.O.C. MDR FOOT SWITCH UTILITY INTERNET RHYTHM PROGRAM VOICE EDIT PATTERN SEQUENCE U.ORGAN FLUTES 2 6 L.
レジストシフト画面で設定する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 1 2 [FOOT SWITCH]ボタンを押します。 画面右上の[ライト]ボタンを押して、ライトページ(レジストシフト画面)を表示 させます。 レジストシフト画面 DISPLAY SELECT VOICE DISPLAY A.B.C. M.O.C. MDR FOOT SWITCH UTILITY INTERNET 1 2 3 4 RHYTHM PROGRAM VOICE EDIT PATTERN SEQUENCE 6 U.ORGAN FLUTES レ ジ ス ト レ ー シ ョ ン メ モ リ ー L.
4 ユーザー レジストレーションメモリーを切り替える順番をあらかじめ設定しておき、右のフットス イッチを押すたびに、設定した順にレジストレーションを呼び出します。 レジストレーションメモリーの順番を設定するには: 1 レジストレーションメモリーのナンバーボタンを押します。 2 画面の[セット]ボタンを押します。 レジストレーションが入力され、画面上にナンバーが表示されます。 3 上記の1〜2をくり返して、レジストレーションメモリーの順番を設定します。 編集画面 6 3 1 レ ジ ス ト レ ー シ ョ ン メ モ リ ー 2 1 ポジション 編集画面にあるカーソル(オレンジ色表示)を移動するボタンです。 カーソルは、自分で設定し たレジストレーションシフトのナンバーの間で移動させることができ、 レジストレーションシ フトを自在に編集できます。 最高80レジストレーションまで設定できます。 カーソルを最初の位置(TOP)に戻します。 カーソルを1つだけ左に移動します。 カーソルを1つだけ右に移動します。 カーソルを5つ右に移動します。 2 データ ユーザーレジストレーションシフトの設定、
全消去:ユーザーレジストレーションシフトをすべて消去する場合に使います。 [全消去]ボタンを押すと、消去してもよいかどうか確認を求めるメッセージが表示されます。 [消去]ボタンを押すと、すべてのデータは消去され、消去が実行されたことを示す「すべての データを消しました!!」が一時的に画面上に表示されます。 [キャンセル]ボタンを押すと、消去せずにもとの画面に戻ります。 3 シフトエンド レジストレーションシフトが最後まで進んだときの動作を設定します。 ストップ:最後のレジストレーションを選択して、レジストレーションシフトは終了します (右フットスイッチを押してもレジストレーションは移動しません)。 関連ページ トップ:最後のレジストレーションを選択したあと、最初のレジストレーション(TOP)に戻っ 1つのソングに複数のレジスト レーションを保存する (110ページ) て繰り返しシフトします。 ネクストレジスト:最後のレジストレーションを選択したあと、MDRのソングに入っている 次のレジストレーションデータを自動的に読み込みます。ひとつのソング内に複数のレジスト NOTE レーションデータを保存した
画面右下にレジストレーションシフトの状態が表示されます。現在選ばれているレジスト レーションシフトのモードによって、以下のように表示や操作が異なります。 レジストレーションシフトがオフに設定されている場合 現在のレジストレーションを表示します。 シフトモード時 現在のレジストレーション 次のレジストレーション 6 現在のレジストレーションと次のレジストレーションを表示します。 レ ジ ス ト レ ー シ ョ ン メ モ リ ー ジャンプモード時 移動先のレジストレーション ナンバーを変更 現在のレジストレーションとジャンプ先のレジストレーションを表示します。また、 データコントロールダイアルや ボタンを使って、ジャンプ先のレジスト レーションのナンバーを変更できます。 ユーザーモード時 設定されているユーザーレジストレーションシフトを順番に表示します。現在の レジストレーションはカーソル(オレンジ色)で表示されます。データコントロールダ イアルや画面上のボタンでカーソルを動かすことによって、好きなレジストレー ションの位置に移動できます。間違って右フットスイッチを2度押してしまっ
6 パラメーターの一括変更 ボイスディスプレイの2ページ目には、複数のレジストレーションの同一パラメーターを同 時に変更する機能があります。上鍵盤の音を全レジストレーションについて明るめに設定 したい、といった場合にこの機能を使うと便利です。 一括変更できるパラメーター ● リバーブ ● リズムのリバーブ ● ボリューム ● パン ● ブリリアンス ● サステイン 1 2 6 パネル上の[VOICE DISPLAY]ボタンを押して、ボイスディスプレイを表示さ せます。 画面右上の[2]ボタンを押して2ページ目を表示させます。 DISPLAY SELECT レ ジ ス ト レ ー シ ョ ン メ モ リ ー VOICE DISPLAY A.B.C. M.O.C. MDR FOOT SWITCH UTILITY INTERNET RHYTHM PROGRAM VOICE EDIT PATTERN SEQUENCE U.ORGAN FLUTES 3 L.
選択画面で、一括変更したいパラメーターと、パート(音群や鍵盤)を選びます。 パラメーターとパートを選ぶと、自動的に選択画面が閉じます。選んだパラメー ターのレジストレーションごとの値が画面上に表示されます。 各レジストレーションの パラメーターの値 選んだパラメーター 4 画面右下の操作ボタンを使って、一括変更の対象となるレジストレーション ナンバーをすべて選びます。 6 ONになっているレジストレーションが一括変更の対象となります。 レ ジ ス ト レ ー シ ョ ン メ モ リ ー 画面でオン/オフしたいレジストレーションのナンバーを選び、画面右下の5つの操 作ボタンでON/OFFを切り替えます。 [すべてON]: すべてのレジストレーションをON (一括変更の対象)にします。 [すべてOFF]: すべてのレジストレーションの選択を解除します。 [ON]: 現在カーソルが置かれているレジストレーションをONにします。 [OFF]: 現在カーソルが置かれているレジストレーションをOFFにします。 [選択]: 数字に下線のついたレジストレーションをすべてONにします。下線は、パラメーター の
5 一括変更を行ないます。 現在ONになっているすべてのレジストレーションのパラメーターを一括変更しま す。すべての値を同じにそろえる方法と、すべての値を現在の値より1ずつ増減させ る方法があります。一括変更すると、レジストレーションの内容が変更され、もと には戻せませんので、ご注意ください。画面右下の3つの操作ボタンや、データコン トロールダイアルで一括変更を行ないます。 すべての値を同じにそろえるには: [セット]を押します。 現在ONになっているレジストレーションナンバーのパラメーター値を、一括して現在カーソ ルが置かれているレジストレーションのパラメーター値にそろえます。[セット]を押すと、次 のようなメッセージ画面が表示されます。 6 レ ジ ス ト レ ー シ ョ ン メ モ リ ー [そろえる]ボタンを選択すると、一括変更が行なわれます。作業を中止したい場合は[キャンセ ル]ボタンを選択します。 すべての値を1つずつ増減させるには: 画面の[+]ボタンや[−]ボタンを押すか、データコントロールダイアルを操作すると、一括変 更の対象となっているレジストレーションナンバーのパラメーター値が1
7 ミュージックデータレコーダー (MDR) MU S IC D A T A R E CO R D ER MDR (ミュージックデータレコーダー )は、スマートメディアやUSBフラッシュメモリーなどの外部メディアに、レジ ストレーションや演奏データを録音したり、録音したデータを再生したりする機能です。別売のフロッピーディスクド ライブUD-FD01を取り付けると、フロッピーディスクを使用することもできます(ELS-01C/01Xには、フロッピー ディスクドライブは付属しています)。 使用できる外部メディアについては、インターネット上のヤマハエレクトーンホームページで ご確認ください。 この章の内容 1 MDR機能に入る . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 7 レジストレーションなどのデータを読み込む . . . . . . . 114 • スマートメディア TM(メモリーカード)の取り扱いについて . . 96 • フロッピーディスクの取り扱いについて . . . .
スマートメディアTM*(メモリーカード)の取り扱いについて ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● * スマートメディアは株式会社東芝の商標です。 この楽器にはスマートメディア用のカードスロット(挿入口)が 装備されています。 カードスロットにスマートメディアを挿入すると、本体で作っ たデータをスマートメディアに保存したり、スマートメディア 内のデータを本体に読み込んだりできます。 スマートメディアをご使用いただく場合は、以下のことをお守 りください。 ■ 使用できるスマートメディアの種類 • 電源電圧が3.
フロッピーディスクの取り扱いについて ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ELS-01では、フロッピーディスクをご使用になるにはフロッ ピーディスクドライブUD-FD01を本体に取り付ける必要があ ります。UD-FD01の取り付け方法は、237ページをご覧くだ あと、フロッピーディスクを入れたまま長時間放置すると、 ディスクが汚れ、データの読み書きにエラーが生じる原因に なります。 さい。 ■ 磁気ヘッドの定期的なクリーニング フロッピーディスク(ドライブ)をご使用いただく場合は、以下 • ディスクドライブユニットは高精度の磁気ヘッドを使用して います。ディスクドライブユニットを長時間使用していくう ちに、磁気ヘッドはフロッピーディスクの磁性粉で汚れてき ます。磁気ヘッドが汚れると、録音や再生にエラーが生じる ことがあります。 のことをお守りください。 ■ 使用できるフロッピーディスクの種類 • 3.
2 メディアを初期化(フォーマット)する 新しいメディア(スマートメディアやUSBフラッシュメモリーなど)は、そのままでは使え ない場合があります。この場合、メディアをフォーマット(初期化)する必要があります。 フォーマットとは、メディアをエレクトーンで使用できる形式にする作業です。 フォーマットを実行すると、メディアの中のすべてのデータは消去され、新たにデータが 記録できる状態になります。消去されたデータは永久に失われてしまいます。フォーマッ トを実行する前に、重要なデータが入っていないかどうかよくご確認ください。 1 2 3 メディアを、向きを間違えないようにして、挿入ロにしっかりと挿入します。 画面右上の[ツール]ボタンを押して、ツールページを表示させます。 [フォーマット]ボタンを押します。 7 ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R NOTE ELS-01では、UD-FD01を接続 4 フォーマットしたいメディアを選びます。 スマートメディアをフォーマットする場合は[SmartMedia]を、フロッピーディス クをフォーマットする場合は[USB-FD1]を
3 ソングを選ぶ 演奏データやレジストレーションデータを保存するときには、何も記録されていないソン グを選びます。ソングを再生したり、ソングに名前を付けたりするときには、データが保 存されているソングを選びます。 ソング選択ページでソングを選ぶには: ソング選択ページには、現在選ばれているメディア/フォルダー内のソングが表示されてい ます。表示されているソングの中から、目的のソングを選びます。 1 メディアを確認します。 たとえばスマートメディアのソングを選びたい場合は、画面上部に 「SmartMedia:/」(スマートメディア)と表示されていることを確認します。 現在選ばれているメディア/フォルダー 7 ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R 目的のメディアが表示されていない場合は、101ページの「メディアやフォルダー を変更するには」で目的のメディアを選んでください。 ( これからデータを録音したい場合は、何も書いてない(データの入っていない)ソング ) 2 選択したいソングのボタンを押します。 のボタンを押します。ソングのボタンがオレンジ色に変わり、選択で
1画面にはソング1〜ソング8の8つのソングが表示されています。 画面上の数字ボタンを押すことで、表示させるソングを切り替えます。 たとえば、数字ボタンの[2]を押すとソング9〜ソング16、[3]を押すとソング17〜 ソング24、というように表示されます。 数字ボタンを押すことで、 表示させるソングを 切り替えます ソング1〜ソング8 数字ボタンの[1]を押した場合 数字ボタンの[3]を押した場合 1 7 2 3 4 5 1 2 3 4 ソング1 ソング2 ソング3 ソング4 ソング17 ソング18 ソング19 ソング20 ソング5 ソング6 ソング7 ソング8 ソング21 ソング22 ソング23 ソング24 ソング情報の確認 ソングを選択した状態で[パート設定]ボタンを押すと、そのソングを再生したときに ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R どのパートが再生されるかを確認できます。 ( ) [ F] (再生)ボタンを押したときには、この画面で「PLAY」になっているパートだけ が再生されます。演奏データの入って
メディアやフォルダーを変更するには: 1 画面の[フォルダー選択]ボタンを押すと、下のフォルダー選択画面が表示され ます。 1 2 4 5 6 7 3 1 現在の位置 現在選択されているメディア/フォルダーが表示されます。「:/」の前にはメディアの種類 が、「:/」の後ろにはフォルダー名が表示されます。たとえば、 「SmartMedia:/Folder1/」 と表示されている場合は、「スマートメディア内の」 「Folder1という名前のフォルダー」が 選択されていることを示します。 7 2 メディア/フォルダーリスト 選択できるメディアやフォルダーが表示されます。表示できるフォルダーは最大120個です。 ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R 3 スクロールボタン 表示されているフォルダーが多い場合は、このボタンで表示をスクロールさせます。 4 上に ひとつ上の階層のフォルダーまたはメディアへ移動します。たとえば、現在の位置が 「SmartMedia:/Folder1/」(スマートメディア内のFolder1というフォルダー )の場合は、 ( このボタンを押すことで
NOTE 2 フォルダーを選択したときに、 メディア/フォルダーリストで、目的のメディア/フォルダーを選びます。 選んだメディアの中に入っているフォルダーを表示させたい場合は、選択されてい るメディアのボタンをもう一度押します。 「レジストレーションを初期化し てください」というメッセージ が表示された場合は、[初期化]ボ タンを押してください。 パネル上のレジストレーション 3 目的のメディア/フォルダーを選択したら、[実行]ボタンを押してソング選択 ページに戻ります。 [閉じる]ボタンを押すと、フォルダーを選択せずにソング選択ページにもどります。 メモリーが初期化され、新しい ソングが選べるようになります (メディアが初期化されるわけで はありません)。 アイコン一覧 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ソングを選ぶときに表示される画面で使われているアイコンです。それぞれのアイコンの 意味は次のようになっています。 スマートメディアやフロッピーディスクといったメディアであ
メディア内の構成:フォルダー /ソング/ファイル フォルダーとは フォルダーとは、メディア内のソングを整理するための保管場所です。容量の大きい スマートメディアやUSBフラッシュメモリーには、数百ものソングを保存することが できるので、多くのソングを保存した場合には、呼び出したいソングを探すのが大変に なります。そこで、フォルダーをつくってソングを管理することで、メディア内のソン グを管理しやすくします。 ソング 1 ソング 2 ソング 3 ソング 4 ソング 5 ソング 6 ソング1 ソング2 3 フォルダーA フォルダーをつくると ソング ソング ソング スマートメディア ソング4 5 6 フォルダーB スマートメディア ソングとは 7 ソングとは、本来は「曲」という意味ですが、エレクトーンでは、外部メディアに保存 する1曲分のデータのことをソングと呼びます。1つのソングには、レジストレーショ ンデータや演奏を録音したデータなどがファイルとして保存されています。 ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R ファイルとは エレクトーンでは、ソング
4 演奏を録音する 演奏を録音する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 録音中は、絶対に電源を切った り、メディアを抜いたりしない でください。 演奏を録音する前に、あらかじめ、レジストレーションメモリーの設定など、録音したい 曲の演奏の準備をしておきましょう。 1 2 メディアを挿入口に挿入します。 演奏を録音するソングを選択します。 データの入っていないソングを選びます。ソングの選択については、99ページをご 覧ください。 データの入っているソングに上書きしたい場合は、126ページ「ソングの削除」で、 あらかじめ上書きしたいソングを削除しておいてください。 NOTE EL-900などのELシリーズの 3 画面の[録音]ボタンを押します。 下の画面が表示され、録音待機状態になります。 ソングが入っているフォルダー には、録音できません。 7 ( ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R ) 4 画面の[F](再生)ボタンを押します。 画面上
演奏をやり直す ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 演奏をミスした場合には、はじめからやり直すことができます。 1 2 録音中に、画面の[やり直し]ボタンを押します。 録音が中止され、曲の頭に戻ります。 [ F](再生)ボタンまたは[カスタム]ボタンを押します。 ふたたび録音が開始します。前もって録音されたデータは、すべて新しいデータに 7 置き換わります。 ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R パートごとに録音する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 上鍵盤、下鍵盤、ペダル鍵盤の、それぞれのパートの演奏や、レジストレーションの変更 やエクスプレッションペダルの操作といったコントロールデータを、個別に記録すること ができます。また、リードボイス1とキーボードパーカッションは、上鍵盤/下鍵盤の演奏 と独立して録音することもできます。こ
下のように設定すると、下鍵盤とペダル鍵盤の演奏だけをパート録音できます。 3 4 画面の[F](再生)ボタンを押し、砂時計の表示が消えたら演奏を開始します。 (下鍵盤とペダル鍵盤の)演奏が終了したら、画面の[J](停止)ボタンを押し ます。 これで(下鍵盤とペダル鍵盤の)パート録音ができました。 7 次に、録音しなかった(上鍵盤)パートの録音を行ないます。 5 ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R 画面の[録音]ボタンを押します。 上書きするかどうか確認を求めるメッセージが表示されます。[OK]を選ぶと、録音 待機中の画面が表示されます。 6 録音したいパートを選択します。 新たに録音したいパート(ここでは上鍵盤)を「REC」にします。また、手順2で録音 したパート(ここでは下鍵盤とペダル鍵盤)を「PLAY」にすると、さきほど録音した ( データが再生され、再生音を聞きながらほかのパートを録音できます。 ) 7 新しいパートを録音するために、画面の[カスタム]ボタンを押します。 すでに録音したパート(下鍵盤とペダル鍵盤)の再生が始まりますので、それに
パンチイン録音 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 録音したソングの一部だけを録音し直すことができます。パートを選択することによって、 特定のパートだけをパンチイン録音することもできます。 1 NOTE パンチイン録音したいソングを選びます。 休符と休符ではさまれたフレー ソングの選択については、99ページをご覧ください。 ズごとに、パンチイン録音する と便利です。 2 3 4 [ F](再生)ボタンを押して、ソングを再生します。 録音し直したい位置で、[ K](一時停止)ボタンを押します。 ソングが一時停止状態になります。 [録音]ボタンを押します。 録音画面が表示され、録音待機状態になったことを示します。 5 録音をやり直したいパートを「REC」に設定し、それ以外のパートは「PLAY」 6 [ F](再生)ボタンを押して録音を開始します。変更したい部分だけを演奏し 7 録音し直したい部分の演奏が終わったら、速やかに[ J](停止)ボタンを押して に設定しま
3 4 画面の[ソング名変更]ボタンを押します。 以下の文字入力画面が表示されます。 [E][F]ボタンまたはデータコントロールダイアルを使って、文字を入力し たい位置にカーソルを移動します。 カーソル DATA CONTROL または 7 5 ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R 文字種選択のボタンで、入力したい文字種を選びます。 NOTE 言語設定(17ページ)を 「ENGLISH」(英語)にしている 場合、ひらがなやカタカナは入 力できません。 ( ) NOTE XGソングのソング名は最大で 6 入力したい文字を押します。 最大で25文字(半角文字の場合は50文字)まで入力することができます。文字種を 「かな漢」にしているときは、漢字変換もできます。漢字変換については次のページ 全角23文字です。 をご覧ください。 7 108 ELS-01/01C/01X 取扱説明書 名前を決めたら[OK]ボタンを押して名前を確定します。 文字入力画面が閉じ、ツールページの表示に戻ります。
入力した文字を削除するには: 1 削除したい文字にカーソルを移動します。 カーソル DATA CONTROL または 2 画面右下の[削除]ボタンを押します。 カーソルの位置にある文字が一文字だけ削除されます。 漢字変換をするには: 1 7 入力した文字列が反転表示されているときに[漢字変換]ボタンを押します。 反転表示の範囲が漢字に変換されます。候補の漢字が出てこない場合は、[漢字変換] ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R ボタンを何度か押すと、次の候補が表示されます。 ・文節(反転表示の範囲)を変えたいときは、[E][F]ボタンまたはデータコント ロールダイアルを使います。 ・反転表示の文字をすべて一度に消したいときは、[キャンセル]ボタンを押します。 ( 2 [OK]ボタンを押すか、次の文字を入力すると、漢字が確定します。漢字に変換 された文字列をひらがなに戻したいときは、[削除]ボタンを押します。 ) ソング名やフォルダー名をつけて[OK]ボタンを押すと、 「入力されたファイル名は使用 できません」というメッセージが表示されることがあり
6 レジストレーションを保存する 演奏データを録音せずに、レジストレーションなどのデータだけを記録することもできま す。ここで記録されるデータは、レジストレーションメモリーの設定やレジストレーショ ンシフトだけでなく、ユーザーリズムや、リズムシーケンスデータ、そしてユーザーボイ スやVAカスタムボイスも含まれます。 1 記録したいデータを設定し、記録させたいソングを選択します。 何も記録されていないソングを選びます。ソングの選択については、99ページを ご覧ください。 2 3 [レジスト編集]ボタンを押します。 [保存]ボタンを押します。 レジストレーションデータの読み込み中であることを示すメッセージが、画面上に 表示されます。メッセージが消えたあと、[閉じる]ボタンを押すと、レジストレー ションが保存されたソングに、 「SONG XX」というソング名が表示されます(XXに は数字が入ります)。 7 ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R 1つのソングに複数のレジストレーションを保存する 関連ページ ネクストレジスト(90ページ) レジストレーションシーケンス (18
3 4 表示されているレジストレーションの一番下にある、空白のボタンを押します。 [保存]ボタンを押します。 あらかじめ保存されていたレジストレーションの下に、新しくレジストレーション が追加されます。 レジストレーションを読み込んだときには、ここで一番上に表示されているレジス トレーションが読み込まれることになります。順番を入れ替えたい場合は、112 ページ「ネクストレジスト機能の設定」をご覧ください。 7 レジストレーションだけを入れ替える ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R 演奏データを変えることなく、録音されている曲のレジストレーションだけを変えること もできます。 1 演奏データの入っているソングを選択します。 ソングの選択については、99ページをご覧ください。 ( 3 4 [レジスト編集]ボタンを押します。 画面内にはソングに保存されているレジストレーションが表示されます。 ) 2 上書
ネクストレジスト機能の設定 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 16以上のレジストレーションを使用する曲を演奏する場合は、1つのソング内に複数の レジストレーションデータを保存しておき、それらをつぎつぎに呼び出して再生できます。 これをネクストレジスト機能といいます。 M1 M16 REG_001 M1 M16 REG_002 ネクストレジスト機能を使うには、以下のどちらかの設定をしておく必要があります。 NOTE ●レジストレーションシフトの設定をユーザーモードにして、シフトエンドにネク ネクストレジストを使用すると、 ストレジストを選びます。詳しくは87ページをご覧ください。 ユーザーボイスやVAカスタムボ イスを読み込むときに、発音し ●レジストレーションシーケンスにネクストレジストを入力します。詳しくは180 ない時間が生じることがありま ページをご覧ください。 す。 1 7 1曲で使用したい複数のレジストレーションを、1つのソングに保存します。 レジ
4 1 5 6 7 2 3 1 レジストレーションリスト 編集したいレジストレーションを選びます。選ばれたレジストレーションはオレンジ色に なります。5つ以上のレジストレーションが保存されている場合は、上下のスクロールボタ ン で表示をスクロールできます。 2 移動 選ばれているレジストレーションを、1つずつ上または下に移動します。 3 読み込むデータ 7 選ばれているレジストレーションをパネル上に呼び出すときに、呼び出したいデータだけ をオンにします。114ページをご覧ください。 ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R 4 読み込み 選ばれているレジストレーションをパネル上に呼び出します。呼び出したあとで鍵盤を弾 くことで、レジストレーションの内容を確認できます。 5 保存 ( 現在パネル上に呼び出されているレジストレーションを保存します。現在レジストレー ションリスト(1)で選択されているレジストレーションに保存されます。 ) 6 コピー 画面上で選ばれているレジストレーションをコピーします。コピーされたレジストレー ションは、表示されているレジストレー
7 レジストレーションなどのデータを読み込む ソングに記録されたレジストレーションなどのデータは、簡単にエレクトーンに読み込む ことができます。また、レジストレーションに含まれている以下の5つの情報を、個別に読 み込むこともできます。 ・レジスト:レジストレーション(レジストレーションメモリーに保存されている情報) ・ユーザーボイス:ユーザーボイス、VAカスタムボイス ・K.B.P.
5 [読み込み]ボタンを押すと、手順4で選んだデータが読み込まれます。 NOTE 6 リズムの再生中にレジストレー 画面右上の[閉じる]ボタンを押して、レジスト編集画面を閉じます。 ションを読み込むと、シーケン スデータやユーザーリズムは読 み込まれません。 プロテクトソングの選択中は、読み込むデータのボタンが使用できない場合があります (ボタンがグレーアウトされて、選べなくなります)。これは、プロテクトソングの著作 権を保護するためです。たとえば、プロテクトソングの一部分だけを別のソングに読み 込んで別のソングとして保存することはできません。 プロテクトソングについて 市販のソングデータの中には、誤消去防止、または著作権保護のため、上書きやコピー ができないようにプロテクトがかけられているものがあります。このようなソングデー NOTE タのことを「プロテクトソング」といいます。プロテクトソングは、ID付きのスマート 使用できるUSBフラッシュメモ メディアまたはUSBフラッシュメモリーに保存できます。 リーについては、インターネッ トのヤマハエレクトーンホーム プロテクトソングも、
プロテクトソングの詳細表示 関連ページ 画面に表示させる言語を選ぶ (17ページ) ELS-01/01C/01X用の市販データについて、作曲者や編曲者などの情報を、エレク トーンの画面上で確認できます。この機能を使うときは、言語設定を[日本語]にしてお いてください。 NOTE 1 ソング選択画面で、情報を確認したいプロテクトソングを選びます。 EL-900などの市販データをEL →ELS変換したソングについて プロテクトオリジナルソングを選んでください。プロテクト編集ソングを選んだ は、情報は表示されません。 場合は、情報は表示されません。ソングの選択については99ページをご覧くだ さい。 2 手順1で選んだソングのボタンをもう一度押します。 画面上に曲名や作曲者名などの情報が表示されます。表示される内容は、ソング によって異なります。[次へ]ボタンを押すと、さらに情報を見ることができます。 7 3 [OK]ボタンを押して、情報表示を閉じます。 ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R 8 ソングを再生する ( 1 2 再生させたいソングを選択します。
カスタムプレイ レジストレーションやほかのデータを読み込まないで、演奏データだけを再生したい場 合は、[F](再生)ボタンの代わりに[カスタム]ボタンを押します。すぐに再生がスター トします。 ネクストレジスト機能を使った曲を再生する場合には、[カスタム]ではなく[F](再生) ボタンで再生をスタートさせてください。 7 特定のパートだけを再生する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● MDRでは、演奏データの特定のパートだけを再生することもできます。特定のパートの練 ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R 習をする場合などに便利です。 特定のパートだけを再生するには: ソングの再生中に、画面の各パートボタンを押して、再生したいパートは「PLAY」、再生 したくないパートは「OFF」に設定します。 ( ) ELS-01/01C/01X 取扱説明書 117
早送り/巻戻し/一時停止 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 再生中に、早送りや巻戻し、一時停止などができます。 早送り/巻戻しをするには: 画面上の[ H](早送り)または[G](巻戻し)ボタンを押したままにします。再生は中断され、 画面の時間表示も、早送り/巻戻しに従って変化します。 ボタンを押さえるのをやめても、再生は中断されたままです。早送り/巻き戻しをしたところ から再生をスタートするには、[ F](再生)ボタンまたは[カスタム]ボタンを押してください。 一時停止するには: 再生中に、画面上の[ K](一時停止)ボタンを押すと、ソングを一時停止します。 [ K](一時停止)ボタンをもう一度押すか、[F](再生)または[カスタム]ボタンを押すと、 一時停止したところから再生がスタートします。 再生テンポを変更する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● メディアに録音
変更したテンポをもとに戻すには: 一度変更したテンポをもとの状態(100%)に戻すには、テンポ表示の右にある[テンポ リセット]ボタンを押します。 リピート再生する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 特定の曲だけを繰り返し再生したり、同じフォルダーに録音されている全部の曲を繰り返 し再生することができます。 1 7 リピート再生したいソングを選択します。 フォルダー内の全曲をリピート再生したい場合は、1曲目に再生したい曲を選択し ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R ます。ソングの選択については99ページをご覧ください。 2 画面上の[リピート設定]ボタンを押します。 リピート設定の画面が表示されます。 ( 3 画面右上の[ツール]ボタンを押して、ツールページを表示させます。 ) ELS-01/01C/01X 取扱説明書 119
4 画面に表示されたボタンの中から、リピート再生の方法を選択します。 1 2 3 4 1 すべて 現在選ばれているフォルダー内のすべての曲を、順番に繰り返し再生します。 2 シングル 現在選ばれている曲を繰り返し再生します。 3 ランダム 現在選ばれているフォルダー内のすべての曲を、任意の順番で繰り返し再生します。 4 停止 7 リピート再生しません。 5 ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R 6 画面右上の[閉じる]ボタンを押して、画面を閉じます。 ソング選択ページの[F](再生)ボタンを押すと、上で選んだ方法でリピート再 生がスタートします。 再生を停止すると、リピート設定は解除されます。 ( ) 120 ELS-01/01C/01X 取扱説明書
XGソングデータの再生 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 市販のXGソングデータや、コンピューターを使って作ったMIDIデータを再生することがで 関連ページ きます。また、エレクトーンで演奏したデータ(録音したソング)をXG変換機能でXGデータ に変えた場合も、以下の手順で再生できます。また、エレクトーンで作成したソングと同 XG変換機能(127ページ) じように、再生中の早送り、巻き戻し、一時停止ができます。 1 2 3 XGソングデータの入ったメディアを挿入口に差し込みます。 ソング選択ページで、XGソングデータの入ったメディアを選択します。 メディアの変更については101ページをご覧ください。 7 ソング選択ページの[XG]ボタンを押して、メディア内のMIDIファイル(XGソ ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R ング)を画面に表示します。 1枚のメディアに、エレクトーンで作成したソングデータとXGソングの両方が入っ ている場合、画
5 画面の[F](再生)ボタンを押して再生を開始します。 下の画面が表示され、各パートのミュート(消音)設定や音量バランスの設定ができ ます。 3 1 2 1 パートボタン 各パートの再生/ミュートを切り替えます。パートボタンを押すたびに、PLAY/OFFが切 り替わります。再生したいパートを「PLAY」に、再生したくないパートを「OFF」に設 定します。 2 XGボリューム 7 XGソングの全体のボリュームを、0〜100の範囲で調節します。画面に直接触って操作す るか、データコントロールダイアルで操作します。 ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R 3 パート設定 各パートの音量バランスを設定します。このボタンを押すと、下の画面が表示されます。 ( ) XGソングのパートごとのボリュームを0〜100の範囲で調節します。[すべて]のスライ ダーでは、ソング全体のボリュームを調節します。XGボリューム(2)と同じ機能です。 スライダーの下のチャンネルボタン([CH1]など)を押すと、そのパートの再生/ミュートが 切り替わります。パートボタン(1)と同じ機能です。
9 その他の機能(ツール)を使う ソングをコピーしたり削除したり、あるいはソングの容量を確認したりなどさまざまな機 能があります。MDR画面のツールページで設定します。 ソングコピー ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 1つのソングのデータを、別のソングにコピーする機能です。1つのメディア内でも、異 なったメディア間でもコピーできます(EL-900などのELシリーズのソングはコピーできま せん)。メディアの容量が足りない場合や、フォルダー内に100曲のソングが存在している 場合は、コピーは実行されませんので、あらかじめ十分空き容量があることをご確認くだ さい。XGソングをコピーしたい場合は、ここで示す手順とは異なります。128ページ 「XGソングコピー」をご覧ください。 プロテクトソングの移動 プロテクトソングは、同一フォルダー内ではコピーできますが、別のメディアや別の フォルダーにはコピーできません。コピー先として別のメディアやフォルダーを指定す ると「移動しますか? 」というメッセー
3 画面の[ソングコピー ]ボタンを押します。 ソングコピーの画面が表示されます。 コピーしたいソングが、 「コピー元」に表示されていることを確認します。コピーす るソングを変更したい場合は、コピー元の[変更]ボタンを押して表示される画面で、 ソングを選び直します。 4 画面のコピー先[変更]ボタンを押して表示される画面で、コピー先のソングを 指定します。 何も入っていないソングを選んでください。すでにデータが入っているソングを選 んだ場合は、コピーを実行したときに、上書きするかどうか確認を求めるメッセー ジが表示されます。 7 ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R コピー中(またはプロテクトソン グの移動中)は、絶対に電源を 切ったり、メディアを抜いたり しないでください。データが失 われるおそれがあります。 5 コピー先の指定が終わったら、[実行]ボタンを押してソングコピーを実行しま す。[キャンセル]または[閉じる]ボタンを押すと、コピーせずにもとの画面に戻 ります。 コピー先のソング名は、もとのソング名の最初に「*」が付いたものになります。プ ロテクトソン
3 画面の[フォルダー選択]ボタンを押して表示される画面で、「MEMORY」を選 びます。 NOTE [MEMORY]ボタンが表示されな い場合は、画面の[上に]ボタンを 数回押して[MEMORY]を表示さ せます。 4 [実行]ボタンを押してフォルダー選択画面を閉じ、ソングコピーの画面に戻り ます。 「コピー先」に「MEMORY:/」が表示されていることを確認します。 5 [実行]ボタンを押します。 コピーしたいソングが、エレクトーンの内部メモリーにコピーされます。画面には コピーを中止したい場合は、 「コピー元のメディアを抜いてください」というメッセージが表示されます。 6 NOTE [キャンセル]ボタンを押します。 7 コピー元のメディアを抜きます。 コピー元のメディアを抜くと、画面には「コピー先のメディアを挿入してください」 と表示されます。 NOTE ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R プロテクトソングの移動中(手順 5〜9)は、絶対に電源を切らない でください。データが失われる 7 おそれがあります。 コピー先のメディアを挿入口
データの大きいプロテクトソングを移動する場合 別のスマートメディアにプロテクトソングを移動する場合は、移動したいソングをエレ クトーンの内部メモリー (MEMORY)にいったん移動したあとで、移動先のスマートメ ディアに移します。しかし、プロテクトソングの容量が大きい場合には、内部メモリー に入りきらないことがあります。この場合は、何回かに分けてソングを移動することに なり、手順6から9を繰り返す必要があります。画面の指示に従って操作してください。 ソングの削除 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ソング内のデータを削除します。レジストレーションデータだけ、演奏データだけを削除 したり、ソング自体を削除したりできます。ここで説明する方法は、ELS-01/01C/01X で作成したレジストレーションデータや演奏データの削除です(EL-900などのELシリーズ のソングは、削除できません)。 XGソングを削除したい場合は、ここで示す手順とは異なります。129ページ「XGソング の削除」をご覧く
4 削除したいデータ(レジストレーション、ソング)を選択します。 ソング全体を削除する場合は「レジスト」と「ソング」の両方にチェックをつけま す。「レジスト」だけにチェックをつけると、ソング内のレジストレーションデータ だけが削除されます。「ソング」だけにチェックをつけると、ソング内の演奏データ だけが削除されます(レジストレーションデータが入っていないソングでは、「レジ スト」にチェックをつけることはできません。また、演奏データが入っていないソ ングでは、「ソング」にチェックをつけることはできません)。 5 [実行]ボタンを押します。 「削除しますか?」というメッセージが表示され、[削除]を選ぶと削除を実行します。 [キャンセル]を選ぶと削除せずにもとの画面に戻ります。 XG変換機能 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● XG変換機能は、ELS-01/01C/01Xで演奏したデータ(録音したソング)を、XG機器など で再生できるように変換する機能です。ただし、XGソングに変換した場合
4 [実行]を選択します。 画面に「確認しています・・・」というメッセージが表示され、ソングの再生が始 まります(エレクトーンのXG音源で再生します)。最後まで再生すると、以下のよう なメッセージが表示されます。 5 6 7 (必要に応じて)[名前変更]ボタンを押して、保存するソングに名前をつけます。 名前のつけ方は、107ページをご覧ください。 [変換]ボタンを押します。 XG変換が完了し、元の画面に戻ります。 XG変換機能を使って作成されたXGソングは、ソング選択ページで[XG]を選択する と画面に表示されます。XGソングについては、121ページの「XGソングデータの ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R 再生」をご覧ください。 XGソングコピー ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ( 1 コピーしたいXGソングを選択します。 XGソングの選択方法は、121ページ「XGソングデータの再生」をご覧ください。 ) 2 3 128 EL
コピーしたいソングが、「コピー元」に表示されていることを確認します。コピーす るソングを変更したい場合は、コピー元の[変更]ボタンを押して表示される画面で、 ソングを選び直します。 4 画面のコピー先[変更]ボタンを押して表示される画面で、コピー先のメディア 5 コピー先の指定が終わったら、[実行]ボタンを押してソングコピーを実行します。 を指定します。 [キャンセル]または[閉じる]ボタンを押すと、コピーせずにもとの画面に戻ります。 メディアの容量が足りない場合は、XGソングコピーはできません。画面にエラー メッセージが表示され、処理が中断されます。1つのフォルダーには、XGソングは 120曲まで保存できます。 XGソングの削除 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● XGソングを削除することができます。 1 2 7 削除したいXGソングを選びます。 XGソングの選択方法は、121ページ「XGソングデータの再生」をご覧ください。 ミ ュ ー ジ ッ ク デ ー タ レ コ
ELS→EL変換機能 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 関連ページ プロテクトソングについて(115 ページ) フロッピーディスクドライブ UD-FD01の取り付け (237ページ) NOTE ユーザーリズムはELS→EL変換 できません。 このエレクトーン用のソングを、EL-900などのELシリーズのエレクトーンで使用できる データに変換して、フロッピーディスクに保存します。ただし、市販のデータやインター ネットから購入したソングデータなどのプロテクトソングは、EL変換はできません。 ELS-01をお使いの場合は、別売のフロッピーディスクドライブUD-FD01を取り付ける 必要があります。 1 2 ELシリーズの形式に変換したいソングを選びます。 ソングの選択については99ページをご覧ください。 ツールページで[ELS→EL変換]ボタンを押します。 ELS→EL変換の画面が表示されます。 7 ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R 変換したいソングが選
1 2 3 フロッピーディスクを挿入口に差し込み、ELS変換をしたいソングを選びます。 ソングの選択については99ページをご覧ください。 ツールページで[EL→ELS変換]ボタンを押します。 ELS変換の画面が表示されます。 変換したいソングが選ばれていることを確認します。変換元に目的のソングが 表示されていない場合は、変換元[変更]ボタンを押して表示される画面で、ソ ングを選び直します。 4 7 画面の変換先[変更]ボタンを押して表示される画面で、変換先のソングを指定 します。 変換後のデータをこのエレクトーンで使用するためには、変換先をスマートメディ ミ ュ ー ジ ッ ク デ ー タ レ コ ー ダ ー M D R アまたはUSBフラッシュメモリーのソング1〜ソング100にしておく必要がありま す。ここで変換先を指定しない場合、空いているソングが自動的に変換先になりま す。 「EL→ELS変換を実行しますか?」というメッセージが表示され、[変換]を選ぶと ( 5 画面上の[実行]ボタンを押します。 EL→ELS変換が実行されます。変換先メディアの容量が足りない場合は、画面に 「
8 ボイスエディット V O IC E ED I T エレクトーンに内蔵されているボイスの音色や音量を変更して、オリジナルのボイスをつくることができます。この機 能をボイスエディット機能といいます。 まずは「ボイスの構成」を読んで、エレクトーンに入っているさまざまな楽器音がどのようにつくられているかを理解 しましょう。ボイスの構成が理解できたら、次に「ボイスをエディットする」を読みながら実際のエディット作業に進 みましょう。 この章の内容 1 ボイスの構成 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 3 エディットしたボイスを保存する . . . . . . . . . . . . . . . 142 • AWM音色の構成 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 • VA音色の構成 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VA音色の構成 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● VA音色は、生楽器の性質をシミュレートしてつくられています(VA音源)。 VA音色のボイスエディットでは、もとのボイスの音量や音質を変更したり、AWM音源で つくられたエレメントを加えたりして、オリジナルのボイスをつくることができます。 ELS-01C/01Xのリードボイス2に入っているボイスは、すべてVA音色です。それ以外の 音群は、すべてAWM音色です。 2 ボイスをエディットする エディットしたいボイスを選ぶ ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 1 エディットしたいボイスを鍵盤に呼び出します。 たとえば、アコーディオン1の音をエディットしたい場合は、いずれかの音群のボイ スボタン(またはユーザーボタン)でアコーディオン1を選んでおきます。 UPPER KEYBOARD VOICE 1 BRILLIANCE STR
2 [VOICE EDIT]ボタンを押しながら、パネル上のエディットしたいボイスボタン を押します。 [VOICE EDlT]ボタンを押すと、画面上に「エディットするボイスを選んでください !!」というメッセージが現れます。このメッセージが表示されている間に、ボイス ボタンを押します。 DISPLAY SELECT VOICE DISPLAY A.B.C. M.O.C. MDR UPPER KEYB FOOT SWITCH UTILITY INTERNET RHYTHM PROGRAM VOICE EDIT PATTERN SEQUENCE U.ORGAN FLUTES L.ORGAN ROTARY SP SPEED FLUTES STRINGS BRASS WOODWIND PIANO ORGAN PERCUSSION ボイスボタンを 押します 押しながら...
AWM音色のエディット ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● AWM音色のエディットは、ボイスエディット画面のAWMページとLAYER (レイヤー ) ページで行ないます。AWMページは、ボイス全体の音質を調整するためのページで、 LAYERページは、ボイスを構成する各エレメントを細かくエディットするためのページ です。 AWMページ 1 2 3 1 エレメントオン/オフ AWM音源の4つのエレメントとVA音源を表しています。押すたびに、オンとオフ(消音)が 切り替わります(オフにしたエレメントはグレー表示になります)。AWM音色をエディット している場合、[VA]ボタンをオンにすることはできません。 8 2 EQローフリケンシー /EQローゲイン 低い周波数の音量を変化させます。フリケンシースライダーでは、音量変化させたい周波 数を32Hz〜2.
LAYERページ 1 3 2 1 エレメント選択 エディットしたいエレメントを選択します。 2 エレメントオン/オフ AWM音源の4つのエレメントとVA音源を表しています。押すたびに、オンとオフ(消音)が 切り替わります(オフにしたエレメントはグレー表示になります)。エディット中のエレメン トだけをオンにしておくと、エディット内容が確認しやすくなります。ただし、いくつか のエレメントをオフにすると、鍵域や弾く強さによっては音が出ないこともあります。 3 画面切り替え LAYERページは、3つの画面で構成されています。 ボタンで画面を切り替えられ ます。それぞれの画面の内容は、以下のとおりです。 8 LAYERページ【1】 ボ イ ス エ デ ィ ッ ト このボタンで画面を 切り替えます 1 2 3 4 1 ボイス/エレメント エディット中のエレメントが表示されます。上のイラストでは、アコーディオン1のエレメ ント1をエディットしていることを表します。 別のボイスで使われているエレメントを呼び出して、現在エディットしているエレメント と差し替えることもできます。ボイス、エレメントのそ
2 レベル エレメントの出力レベルを設定します。 設定範囲:0〜127 3 ノートリミット エディット中のエレメントを発音させる音域を設定します。ここで設定した最低音(ロー ) と最高音(ハイ)の間でのみ発音します。最高音(ハイ)を最低音(ロー )より低く設定すること はできません。エレメントによっては、設定したとおりにノートリミットの効果がかから ないものもあります。 設定範囲:C−2〜G8 4 パン ステレオ出力によるエレメントの左右の位置を設定します。 設定範囲:L64〜R63 LAYERページ【2】 1 2 3 4 5 8 6 ボ イ ス エ デ ィ ッ ト 1 ノートシフト 現在選択しているエレメントのピッチを、半音単位で移調します。 設定範囲:−64〜+63 2 チューンファイン 現在選択しているエレメントのピッチを、微調整します。 設定範囲:−64〜+63 3 アタックレート 鍵盤を押さえたとき、0から最大の出力レベルに達するまでの速さを設定します。値が大き 関連ページ エンベロープパラメーター (141ページ) いほど、音の立ち上がりが速くなります。 設定範囲:0〜127
5 カットオフフリケンシー フィルターのカットオフ周波数(フリケンシー )を設定します。 設定範囲:9600〜24000セント 6 レゾナンス カットオフ周波数付近の倍音(高調波)を強めて、クセのある音色にします。値を大きくする ほど、倍音が強調されます。エレメントによっては、効果のかかりにくいものがあります。 設定範囲:16〜140 フィルター (カットオフ周波数とレゾナンス) フィルターとは、ある特定の周波数帯だけを通過させて、ほかの周波数の信号を出力さ せない機構です。このエレクトーンでは、低い周波数だけを通過させ、高い周波数は出 力させないタイプのフィルター (ローパスフィルター )を採用しています。 カットオフ周波数 音量 周波数 この部分の周波数の音はフィルターを通過する 音量 レゾナンス 8 周波数 ボ イ ス エ デ ィ ッ ト カットオフ周波数 どの周波数までを通過させるかを決めるのがカットオフ周波数です。カットオフ周波数 以下の信号は通過させ、それ以外の高周波はカットします。一般的には、カットオフ周 波数を下げるほど、高音がたくさんカットされるので音色は暗くなります。また、カ
LAYERページ【3】 1 2 3 4 5 1 LFOウェーブ LFOから発振される出力波形(ウェーブ)を選択します。140ページをご覧ください。 2 LFOスピード LFOから発振される信号の速さを設定します。値が大きいほど、スピードが上がります。 設定範囲:2〜93 3 LFOピッチ LFOでピッチを周期的に変化させます。値が大きいほど、ピッチの変化幅が大きくなりま す。値を0にすると、ピッチは変化しません。 8 設定範囲:0〜400 4 LFOフィルター ボ イ ス エ デ ィ ッ ト LFOでフィルターのカットオフ周波数(フリケンシー )を周期的に変化させます。値が大き いほど、変化幅が大きくなります。値を0にすると、周波数は変化しません。 設定範囲:0〜4800セント 5 LFOアンプリチュード LFOで音量を周期的に変化させます。値が大きいほど、音量の変化幅が大きくなります。 値を0にすると、音量は変化しません。 設定範囲:0〜128 上記1〜5のパラメーターをエディットしてつくったユーザーボイスは、ビブラートをプ 関連ページ リセットに設定して使用することをおすすめします
LFO (ローフリケンシーオシレーター ) LFOは、低い周波数の信号を発生する発振器です。LFOから発振された低周波で、 ピッチをふるわせてビブラート効果をかけたり、音質をふるわせてワウワウ効果をかけ たり、音量を揺らしてトレモロ効果をかけたり、といった使い方ができます。 発振する信号の波形としては以下の5種類が用意されています。いろいろな波形で どんな効果が得られるか、試してみてください。 鋸歯波 (saw) 三角波 (tri) 矩形波 (squ) ランダム (rnd) 正弦波 (sine) VA音色のエディット (ELS-01C/01X) ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● VA音色のエディットは、ボイスエディット画面VAページで行ないます。ELS-01ではVA ページは表示されません。 8 VAページ ボ イ ス エ デ ィ ッ ト 1 2 3 4 5 6 7 1 エレメントオン/オフ AWM音源の4つのエレメントとVA音源を表しています。押すたびに、オ
3 アタックレート 鍵盤を押さえたとき、0から最大の出力レベルに達するまでの速さを設定します。 値を+(プラス)にすると音の立ち上がりが速くなり、−(マイナス)にすると音の立ち上がり が遅くなります。 設定範囲:−64〜+63 4 ディケイレート 最大の出力レベルから(鍵盤を押さえている間、鳴り続ける)一定のレベルに達するまでの速 さを設定します。 設定範囲:−64〜+63 5 リリースレート 鍵盤から指をはなしたあと、出力レベルが0になるまでの速さを設定します。値を+(プラ ス)にすると音が消えるまでの時間が短くなり、−(マイナス)にすると音が消えるまでの時 間が長くなります。 設定範囲:−64〜+63 6 EQロー 関連ページ 音を構成する成分(周波数)のうち、低音部を強調したり(+)、抑えたり(−)します。 EQ (イコライザー ) (135ページ) 設定範囲:−64〜+63 7 EQハイ 音を構成する成分(周波数)のうち、高音部を強調したり(+)、抑えたり(−)します。 設定範囲:−64〜+63 8 ボ イ ス エ デ ィ ッ ト エンベロープパラメーター 個々の楽器によって、鍵盤を押さえた
3 エディットしたボイスを保存する ボイスエディットでつくったAWM音色は、ユーザーボイスとして16個まで保存できます。 また、VA音色は、VAカスタムボイスとして6個まで保存できます。 1 画面右上の[保存]ボタンを押して、保存ページを表示させます。 AWM音色とVA音色とで画面は異なります。 AWM音色の場合 VA音色の場合 2 画面上で、保存したいユーザーボイスナンバーまたはVAカスタムボイスナン バーを押します。 画面上に、保存してよいかどうか確認を求めるメッセージが表示されます。(前もっ て保存しておいたデータを間違って消したりしないようにするためです。) 8 3 ボ イ ス エ デ ィ ッ ト (必要に応じて)[名前変更]ボタンを押して、保存するボイスに名前をつけます。 名前のつけ方は、ソング(MDR)の名前のつけ方と同じです(ただし、ボイスネームは 最大で半角16文字までです)。107ページをご覧ください。 4 [保存]ボタンを押すと、 「保存しました」というメッセージが一時的に表示され て、ユーザーボイスまたはVAカスタムボイスが保存されます。[キャンセル]ボ タンを押
4 ボイスエディットを終了する ボイスを保存したあとや、エディットを中止したいときなど、どのページからでも簡単に 終了できます。 1 パネル上の[VOICE EDIT]ボタンを押します。 エディットしたボイスがすでに保存されている場合は、そのままボイスエディット を終了します。エディットしたボイスがまだ保存されていない場合には、保存せず に終了してよいか確認を求めるメッセージが現れます。 2 [終了]ボタンを押すと、エディットしたボイスを保存せずにボイスエディットを 終了します。 [キャンセル]ボタンを押すと、ボイスエディット画面に戻ります。 ボイスエディットを終了すると、画面の左上が数秒間、水色に点灯し、ボイス エディットの内容を保存していることを示します。点灯中は電源を切らないでく ださい。 5 保存したボイスを呼び出す 8 保存したユーザーボイスは、各音群のユーザーボタンを使って呼び出します。第2章の 「ユーザーボタンでボイスを選ぶ」(30ページ)をご覧ください。 UPPER KEYBOARD VOICE 1 BRILLIANCE STRINGS BRASS WOODWIND
9 リズムプログラム RH YTH M P R O G RA M リズムプログラムには、高品位でバラエティ豊かな打楽器音色を駆使して、ユーザーリズムパターンをつくり出せる リズムパターンプログラムと、内蔵されているリズムやユーザーリズムを1小節ずつ自由に並べ替えて、自分自身の リズムシーケンスが楽しめるリズムシーケンスプログラムがあります。リズムシーケンスプログラムでは、レジスト レーションシーケンスの情報も組み込んで、自動的にレジストレーションとリズムを切り替えながら演奏することもで きます。 この章の内容 1 リズムプログラムの概要 . . . . . . . . . . . . . . . . . . . . . . 144 2 リズムパターンをつくる:リズムパターンプログラム . . 145 • リズムパターンプログラムを始める . . . . . . . . . . . . . . . 145 • 入力するリズムの基本設定をする . . . . . . . . . . . . . . . . . 147 • 打楽器(リズム)を入カする−ステップ入力 . . . . . . . . . . .
リズムパターンをつくる: 2 リズムパターンプログラム リズムパターンプログラムでは、下鍵盤と上鍵盤の各キーに割り当てられた打楽器音を 使って、オリジナルのリズムをつくることができます。つくったリズムパターンは、 48パターンまでユーザーリズムとして保存できます。 リズムパターンプログラムを始める ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● リズムパターンプログラムでは、エレクトーンに内蔵されているリズムや、すでにつくっ てあるユーザーリズムをもとに、一部だけ変更して新しいリズムをつくる方法と、何も入 力されていない状態からひとつひとつの打楽器を入力して、オリジナルのリズムをつくり 上げていく方法とがあります。 既存のリズムをもとにしたリズムをつくる場合: 内蔵リズムやすでに作成してあるユーザーリズムの中に、これからつくりたいリズムパ ターンと似たものがある場合は、既存のリズムパターンをもとにしてプログラムを始める と便利です。 1 2 もとになるリズムをパネルに呼び出します。 [PATTE
既存のリズムをもとにせず、最初からプログラムを始める場合: [PATTERN]ボタンを押して、すぐに手を離します。この場合は、何も入力されていない状 態からオリジナルのリズムパターンをつくることになります。 ひとつのリズムは、リズムパターンのバリエーションとして15種類のセクション(イントロ1〜3、メインA〜D、 フィルインA〜D、ブレイク、エンディング1〜3)から構成されています。 リズムパターンプログラムでは、これらのセクション1つ1つについて、打楽器を入力したり消去したり、あるい は、ほかのリズムで使っているセクションをコピーして集めてきたり(アセンブリー )して、新しいユーザーリズム をつくります。 ケース1:既存のリズムから一部を変更して、ユーザーリズムをつくる 既存のリズム ユーザーリズム イントロ1 メインA フィルインA 2 B B 3 C C D D イントロ1を イントロ1' に変更 保存 エンディング1 フィルインA イントロ1' メインA 2 B B 3 C C D D エンディング1 ブレイク 2 2 3 ブレイク 3
入力するリズムの基本設定をする ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 設定ページで、拍子や小節数などの設定を行ないます。また、別のリズムで使っているセク ションをコピーしたり、ドラムやアカンパニメントの各パートを削除したりもできます。 1 2 画面上の[設定]ボタンを押して、設定ページを表示させます。 リズムの拍子を設定します。 表示されているボタンの中から拍子を選びます。 9 リ ズ ム プ ロ グ ラ ム 既存のリズムをもとにしてプログラムを始める場合、現在入力されているリズムの 拍子とは異なる拍子が選ばれると、次のようなメッセージが現れます。 すべてのセクションのデータを消去する場合は[消去]ボタンを選びます。メッセージ 画面が閉じ、すべてのデータが消去されて拍子が変更されます。 [キャンセル]ボタンを選ぶと、拍子を変更せずに、もとの画面に戻ります。 ELS-01/01C/01X 取扱説明書 147
3 リズムパターンを入力するセクションを選びます。 画面上でセクションのボタンを押すと、セクション選択画面が表示されます。選択 画面でセクションを選ぶと、自動的に選択画面が閉じます。 セクションを変更して、パネル上の[START]ボタンでリズムをスタートすると、選 んだリズムを確認できます。リズムを鳴らしながらセクションを変更することもで きます。アカンパニメントをオフにしたい場合は、163ページをご覧ください。 4 入力する小節数を選びます。 画面上で小節数のボタンを押して、表示される一覧の中から、リズムパターンの 長さ(小節数)を選びます。ただし、セクションにフィルインやブレイクを選んでいる 場合は、自動的に1小節に設定され、変更することはできません。 5 必要に応じて、メトロノームやアセンブリーなどの設定をします。 9 2 リ ズ ム プ ロ グ ラ ム 3 1 1 メトロノーム 関連ページ ステップ入力とリアルタイム入力 (150ページ) 打楽器(リズム)を入力する−リア ルタイム入力(158ページ) 148 メトロノームのオン/オフを設定します。メトロノームをオンにしてリズム
2 アセンブリー ほかのリズムから現在プログラム中のリズムに、パートをコピーします。複数のリズムか らセクションを組み合わせてユーザーリズムを作成する場合に便利です。 [アセンブリー ]ボタンを押すと、以下の画面が表示されます。 コピー元のリズム、 セクション、パートを 選びます コピー先のセクション、 パートを選びます コピーを実行するときに押します どのリズム/セクションのどのパートをコピーするかを選択します。打楽器パートやアカンパ ニメントのうちの1パートだけをコピーしたり、すべてのパートをコピーしたりできます。 コピー先のセクションとパートを選択したあと、コピー元のリズム、セクション、パートを 選択してください。 コピー元とコピー先の設定ができたら、[実行]ボタンを押します。コピーが実行され、元の 画面に戻ります。 3 パート消去 現在入力されているリズムやアカンパニメントのパートを消去します。[パート消去]ボタン を押すと、以下の画面が表示されます。 9 リ ズ ム プ ロ グ ラ ム 表示されたパートの中から、消去したいパートを選びます。データの入っていないパートは 選択できません。[
ステップ入力とリアルタイム入力 リズムパターンプログラムでリズムパターンを入力するには、ステップ入力とリアル タイム入力の2つの方法があります。 ステップ入力は、「何小節目の何拍目に」 「どの打楽器が」「どのくらいの音量で鳴る」 という情報を、ひとつひとつの打楽器音について入力していくことで、リズムパターン をつくる方法です。バスドラムのように1小節の中で決まった位置と音量で使用される 打楽器音をプログラムしたり、また、正確さが要求される場合に適しています。 リアルタイム入力は、鍵盤で弾いた打楽器音がそのままデータとして入力され、前に 入力した音を聞きながら、新しいパートを次々と重ねていくことで、リズムパターンを つくる方法です。実際にパーカッションを演奏することがプログラムすることになるの で、フィーリングをそのまま表現できます。 つくりたいリズムの種類や好みによって、どちらの方法で入力するか選べます。もちろ ん、2つの方法をミックスして、パートごとに使い分けながら、ひとつのリズムをつく ることもできます。ステップ入力で基本ビートをプログラムし、リアルタイム入力でア クセントや装飾音を付けるとよいでしょう。
3 入力したい打楽器のセット(キット)を、鍵盤に呼び出します。 キット名が表示されているボタンを押すと、選択できるキットの一覧が表示されま す。ドラムキットとSFXキットの2つのカテゴリーからキットを選択できます。 それぞれのキットについては、172ページの「キットリスト」をご覧ください。 一覧の中から呼び出したいキット名を押すと、一覧表示が閉じ、選んだキットが上 鍵盤と下鍵盤に呼び出されます。 ドラムキット SFXキット キットは、メインドラムとアドドラムのそれぞれについて1種類ずつしか選べませ ん。違うキットの打楽器音を組み合わせてリズムをつくりたい場合は、メインドラ ムとアドドラムにそれぞれ別のキットを割り当てることで、2種類のキットの打楽器 が混ざったリズムを作成できます。 4 入力したい打楽器が割り当てられているキー (鍵)を押さえて、入力する打楽器 を選びます。 キーを押さえると、その打楽器名が画面に表示され、入力できる状態になります。 選んだキー 5 9 打楽器名 リ ズ ム プ ロ グ ラ ム 入力したいリズムに適したクオンタイズを設定します。 157ページをご覧ください。
6 ホイッスルなどの持続音を入力する場合は、ゲートタイム(音符の長さ)を設定 します。 ゲートタイムの設定が必要な打楽器は、172ページのキットリストでご確認くださ い。ゲートタイムの設定については、161ページをご覧ください。 7 アクセントボタンを押して、表示されているリズムクロックの位置に打楽器音 を入力します。リズムクロックの変更は、クオンタイズ[E][F]ボタンで行 ないます。 1 2 3 1 リズムクロック表示ボックス 関連ページ 入力するリズムの基本設定をする (147ページ) リズムパターンの現在の位置を[小節:拍:クロック]で表示します。 表示の中ではクロックが一番細かく、1拍は480のクロックで構成されています。 設定ページで決めた小節の長さ分の入力を終えると、先頭のクロック[01:01:000]に戻り ます。 2 アクセントボタン 入力したい音量のアクセントボタンを押すたびに、打楽器音が入力されていきます。[ppp] 9 ボタンが一番小さい音、[fff]ボタンが一番大きい音で、8段階の音量で入力できます。入力 と同時に、リズムクロックの表示も、現在選択されているクオンタ
入力した音符を編集/消去する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 入力を間違えた場合には、次の方法で入力した打楽器音の音量を変えたり、消去したりで きます。 入力した音符の音量を変えるには: 1 音量を変えたい音符を選択します。 1 1 2 23 4 5 3 1 次の楽器 入力されている打楽器を、左にあるキーから順に検索します。このボタンを押すたびに、 入力されている打楽器のうち、現在選ばれている打楽器の次(右側)にあるキーが選択され、 打楽器が切り替わります。すでに入力してある打楽器を選びたいときに使用します。 2 音符[ E][F] 同一打楽器内で、現在選ばれている音符の前または次に入力されている音符を選びます。 たとえば上図では、休符である2や5はとばして、1、3、4を順番に選択できます。 9 3 クオンタイズ[ E][F] リ ズ ム プ ロ グ ラ ム 1ステップずつリズムクロックの表示を前または次に進めます。ステップは、選択されてい るクオンタイズによ
2 アクセント表示ボックス、またはアクセントボタンで、音量を変更します。 アクセント表示ボックスで音量を変更する方が、より細かい調整ができます。 1 2 1 アクセント表示ボックス アクセント表示ボックスを押すと、ボックスのまわりに青枠が表示されます。 この状態でデータコントロールダイアルを回すと、0〜127の範囲で、細かく音量を変更 できます。0に設定すると、音は鳴りません。 2 アクセントボタン ppp (ピアニッシッシモ)〜fff (フォルティッシッシモ)の8段階で、音量を変更できます。 変更したい音量のボタンを押すと、現在選択されている音符が、選択した音量に変わります。 入力した音符の位置を移動するには: 1 9 2 リ ズ ム プ ロ グ ラ ム 3 154 ELS-01/01C/01X 取扱説明書 153ページの手順1に従って、移動したい音符を選択します。 リズムクロック表示ボックスを押します。 リズムクロック表示ボックスのまわりに青枠が表示されます。 データコントロールダイアルを回して、音符の位置をクロック単位で変更します。
入力した音符の長さを変えるには: スネアロールやホイッスルのような持続音については、ゲートタイムを変更することで、 音の鳴る長さを調節できます。162ページをご覧ください。 入力した音符を消去するには: 1 2 153ページの手順1に従って、消去したい音符を選択します。 消したい音を選んだ状態で、[休符]ボタンを押します。 入力されていた音が消去されて、休符に置き換わります。 また、特定の打楽器音をすべて消去したり、すべての打楽器の音を消去したりすることも できます。 特定の打楽器音をすべて消去するには: 1 消去したい打楽器が割り当てられているキーを押します。 選んだキー 2 9 選んだキーと打楽器名が、画面に表示されます。 リ ズ ム プ ロ グ ラ ム 打楽器名 画面右下の[消去]ボタンを押します。 次のような表示が現れ、すべての打楽器音を消去するか、選ばれている打楽器音を 消去するかの確認を求めてきます。 ELS-01/01C/01X 取扱説明書 155
3 [消去]を選びます。 「ピンポン」という音がして、選択した打楽器音が消去されたことを知らせます。 このほかに、以下の方法で特定の打楽器音を消去することもできます。 [消去]ボタンを押しながら、 消去したい打楽器音が割り当てられているキーを押します。 「ピンポン」という音がして、その打楽器音が消去されたことを知らせます。 すべての打楽器音を消去するには: 1 画面右下の[消去]ボタンを押します。 次のような表示が現れ、選ばれている打楽器音を消去するか、すべての打楽器音を 消去するかの確認を求めてきます。 2 9 [全てを消去]ボタンを選びます。 瞬間的にすべての打楽器音が消去されます。 また、入力する打楽器を間違えた場合などは、一度消去してから入力し直さなくても、以 下の方法で、すでに入力してある打楽器音をほかの打楽器音に置き換えることもできます。 リ ズ ム プ ロ グ ラ ム ほかの打楽器音に置き換えるには: リズムをストップした状態で、以下の操作をします。 1 変えたい打楽器音が割り当てられているキーを押します。 選んだキーと打楽器名が、画面に表示されます。 選んだキー
クオンタイズについて ステップ入力で楽器音を入力する際の入力タイミング、あるいはリアルタイム入力で タイミングを補正する精度を、クオンタイズで設定します。9種類のクオンタイズ値が 選べます。 このボタンで 切り替えます 1 2 3 4 5 6 7 8 9 5 ステップ入力を行なう場合 選択したクオンタイズで、楽器音を入力することができます。入力ページのクロック表 示ボックスでは、クオンタイズに応じた数字が表示されます。 各クオンタイズで移動できるタイミング 1 2 240 3 120 4 60 6 320 7 160 8 80 9 9 40 クロック 0 120 240 360 480 (1拍) リ ズ ム プ ロ グ ラ ム フリー (5)に設定すると、1クロック(1/480拍)ずつタイミングが移動できます。 リアルタイム入力を行なう場合 クオンタイズを選択すると、入力の際に鍵盤を弾くタイミングが少し前後にずれても、 正しい位置に補正して入力します。ただし、クオンタイズをフリーに設定した場合は、 補正機能は働きません。クオンタイズの設定は、入
打楽器(リズム)を入カする−リアルタイム入力 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● すでに入力してあるリズムを鳴らしたり、メトロノームを鳴らしたりしながら、鍵盤を 弾いて打楽器音を入力します。弾いた音がそのままリズムとして入力されます。 1 2 150ページの手順1〜3に従って、入力するパートやキットを選びます。 入力したいリズムに適したクオンタイズを設定します。 設定されたクオンタイズによって、入力する音符のタイミングが自動的に補正され ます。157ページをご覧ください。 3 リズムの[START]ボタンを押します。 既存のリズムをもとにプログラムする場合はもちろん、何も入力されていない状態 から始める場合にも、リズムをスタートさせます。リズムをスタートさせることが、 リアルタイム入力をスタートすることになり、入力ページは下のようなリアルタイ ム入力の画面に自動的に切り替わります。 9 リ ズ ム プ ロ グ ラ ム 4 リズム(またはメトロノーム)に合わせて、入力したい打楽器
入力を間違えたときには、リズムが鳴っている状態のままで、特定の打楽器音をすべて 消去できます。 特定の打楽器音を消去するには: [消去]ボタンを押しながら、消去したい打楽器音が割り当てられているキーを押します。 指定された打楽器音は、瞬間的にすべて消去されます。 音量や入力位置などを修正する場合は、リズムを停止した状態で操作します。153ページ の「入力した音符を編集/消去する」をご覧ください。 アカンパニメントを選ぶ/つくる(ロワーリズミック機能) ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 自分でつくったリズムに、既存のリズムのアカンパニメントをあわせて一緒に使用したり、 ロワーリズミック機能を使って、下鍵盤にオリジナルのバッキングパターンをつけたりで きます。 既存のリズムのアカンパニメントを選ぶには: 1 2 3 画面上の[設定]ボタンを押して設定ページを表示させます。 [アセンブリー ]ボタンを押します。 コピー先、コピー元を選ぶ画面が現れます。 コピー元の[リズム]ボタンや[
オリジナルのリズミックパターンをつくるには: リズミックパターンの場合も、リズムパターンと同じように、ステップ入力とリアルタイ ム入力のどちらかの方法で入力します。 1 2 画面上の[入力]ボタンを押して、入力ページを表示させます。 パートのボタンで、リズミックパターンを入力するパート(コード1または コード2)を選びます。 ロワーリズミックは、コード1またはコード2のパートに入力します。 既存のリズムからコピーしたデータが入っていた場合は、 「消去しますか?」という メッセージが表示されます。消去してオリジナルのリズミックパターンをつくる場 合は[消去]ボタンを選びます。 NOTE ここで選べるボイスは、各音群で 3 選べるボイスとは異なります。 リズミックパターンに使用する楽器音(ボイス)を選びます。 ボイス名が表示されているボタンを押すと、ボイスメニューが表示されます。ボイ スメニューの中から使用したいボイス名を選ぶと、一覧表示が閉じ、選んだボイス が上鍵盤と下鍵盤に呼び出されます。 9 リ ズ ム プ ロ グ ラ ム ボイスは、リズミックパターンを入力したあとでも、この方法で変更で
4 入力したいリズミックパターンに適したクオンタイズを設定します。 5 ゲートタイムを設定します。 157ページをご覧ください。 ゲートタイムの ボタンで操作するか、ゲートタイムが青枠で囲まれて いる状態でデータコントロールダイアルを操作することで、ゲートタイムを設定し ます。 DATA CONTROL ゲートタイムというのは、音符が実際に発音する長さです。たとえば、ひとくちに4分 音符といっても、スタッカートで弾くこともあれば、テヌートで弾く場合もあります。 そのような「実際に音符を弾く長さ」がゲートタイムです。 1拍は480クロックで構成されているので、4分音符をテヌートで入力する場合は450 〜470程度に、スタッカートで入力する場合は240前後に設定するとよいでしょう。 6 リズミックパターンを入力します。 9 リズムパターンとまったく同じ方法で入力できます。ただし、リズミックパターン の入力時は、鍵盤のどのキーを押してもCの和音(ドミソ)が鳴ります。ステップ入力 の場合は152ページの手順7をご覧ください。リアルタイム入力の場合は158ペー リ ズ ム プ ロ グ ラ ム
ゲートタイムを変更するには: 1 2 3 153ページの手順1に従って、ゲートタイムを変更する音符を選びます。 ゲートタイム表示ボックスを押します。 ゲートタイム表示ボックスのまわりに青枠が表示されます。 データコントロールダイアルを回して、ゲートタイムを変更します。 コード1、コード2以外のアカンパニメントを変更する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● リズムパターンプログラムでは、打楽器パート(メインドラムとアドドラム)、リズミック パート(コード1とコード2)は作成できますが、その他のアカンパニメントのパート (パッド、フレーズ1、フレーズ2)は作成できません。 しかし、パッド、フレーズ1、フレーズ2に関しても、既存のリズムで使われているものを 9 コピーしてそのまま使うだけでなく、音色(ボイス)を変更することができます。 ボイス/エフェクトページでボイスを変更できます。 1 リ ズ ム プ ロ グ ラ ム 2 162 ELS-01/01C/01X 取扱説明書
3 画面に表示されているボタンのうち、ボイスを変更したいパートのボタンを押 します。 ボイスメニューが表示されます。 4 ボイスメニューの中から、使用したいボイスを選びます。 NOTE ボイスメニューが自動的に閉じ、もとの画面に戻ります。 ここで選べるボイスは、各音群で 選べるボイスとは異なります。 上の手順で好きなボイスを選び、各パートのボリュームやパン、エフェクトを調節す ることで、自分のイメージに近いアカンパニメントを作成することができます。 ボリューム/パンを設定する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ボリュームやパンは、ボイス/エフェクトページで設定します。 ボリューム画面 9 1 リ ズ ム プ ロ グ ラ ム 2 1 オン/オフ 各パートのオン/オフを設定します。オフ(OFF)にしたパートはミュート(消音)されます。 2 ボリュームスライダー 各パートのボリュームを設定します。 設定範囲:0〜127 ELS-01/01C/01X 取扱説明書 163
パン画面 各パートのパン(ステレオ出力の左右の位置)を設定します。 設定範囲:L64〜R63 エフェクトをかける ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● リバーブ、コーラス、バリエーションの3種類のエフェクトをかけることができます。 リバーブは音が響き渡るような効果で広がりや奥行き感を与え、コーラスは複数の音が同 時になっているような効果で音に厚みを持たせます。バリエーションは、さまざまな エフェクトの中から好きなものを選んで使用できます。ボイス/エフェクトページで設定し ます。 リバーブ画面 9 リ ズ ム プ ロ グ ラ ム 各パートのリバーブ量を設定します。 設定範囲:0〜127 164 ELS-01/01C/01X 取扱説明書
コーラス画面 1 2 1 コーラスタイプ コーラスエフェクトの種類を選びます。コーラスタイプの表示されているボタンを押すと、 コーラスタイプ一覧が表示されます。 一覧の中から使用したいコーラスエフェクトを選ぶと、一覧表示は自動的に閉じます。 2 コーラススライダー 各パートにコーラスエフェクトをかける量を設定します。 9 設定範囲:0〜127 リ ズ ム プ ロ グ ラ ム ELS-01/01C/01X 取扱説明書 165
バリエーション画面 1 2 3 関連ページ エフェクトリスト(53ページ) 1 バリエーションエフェクトカテゴリー バリエーションエフェクトとして使用したいエフェクトのカテゴリーを選びます。エフェ クト名の表示されているボタンを押すと、エフェクトカテゴリー一覧が表示されます。 一覧の中から使用したいバリエーションエフェクトを選ぶと、一覧表示は自動的に閉じます。 ここで選んだエフェクトに応じて、バリエーションタイプ (2)は自動的に変更されます。 2 バリエーションタイプ 9 バリエーションエフェクトのタイプを選びます。タイプ名の表示されているボタンを押す と、エフェクトタイプ一覧が表示されます。 リ ズ ム プ ロ グ ラ ム LCD 一覧の中から使用したいエフェクトタイプを選ぶと、一覧表示は自動的に閉じます。 3 バリエーションスライダー 各パートにバリエーションエフェクトをかける量を設定します。 設定範囲:0〜127 166 ELS-01/01C/01X 取扱説明書
各打楽器の細かい設定をする ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● それぞれの打楽器音について、チューニングを変更したり、打楽器ごとのパンやボリュー ムを変更したりできます。 1 2 3 画面上の[ドラムセットアップ]ボタンを押して、ドラムセットアップページを 表示させます。 設定を変更したい打楽器パート(メインドラムまたはアドドラム)を選びます。 設定を変更したい打楽器音が割り当てられているキーを押します。 画面に打楽器名が表示され、その打楽器の設定を変更できることを示します。 9 4 リ ズ ム プ ロ グ ラ ム 設定を変更します。 パン、ボリューム、リバーブ、ピッチを変更できます。 1 2 3 4 5 6 ELS-01/01C/01X 取扱説明書 167
1 キット名 選択しているパートで使用しているキット名を表示します。キット名のボタンを押して表 関連ページ キットリスト(172ページ) 示される一覧で、キットを変更することもできます。キットを変更した場合は、すでに入 力されている打楽器音は、新しく選んだキットの音に置き換わります。 2 パン 現在選ばれている打楽器の、ステレオ出力による位置を設定します。 設定範囲:L63〜R63 3 ボリューム 現在選ばれている打楽器のボリュームを設定します。 設定範囲:0〜127 4 リバーブ 現在選ばれている打楽器のリバーブの量を設定します。 設定範囲:0〜127 5 ピッチコース 現在選ばれている打楽器のピッチを、100セント単位で設定します。 設定範囲:−64〜+63 6 ピッチファイン 現在選ばれている打楽器のピッチを、1セント単位で設定します。ピッチコース(5)よりも 細かく設定できます。 設定範囲:−64〜+63 リズムパターンを保存する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 作成したリズム
4 [保存]ボタンを押すと、「保存しました!!」というメッセージが一時的に表示さ れて、リズムパターンが保存されます。[キャンセル]ボタンを押すと、保存し ないで前の画面に戻ります。 画面の右上に、パターンを保存するメモリーの残量が、パーセントで表示されています。 リズムパターンを保存 するメモリー残量 メモリー残量が足りず、パターンを保存できなかったときは、「データがいっぱいで す!!」というメッセージが表示されます。この場合は[OK]ボタンを選択して、前の 画面に戻ってください。 このようなことが起こらないように、データを入力するたびにメモリー残量を チェックすることを心がけてください。メモリー残量が足りず、パターンが保存で きない場合は、必要度の低い打楽器音のデータを消去してから、もう一度試みてく ださい。 リズムパターンを保存したあとは、必ず170ページの方法でリズムパターンプログラムを 終了してください。リズムパターンプログラムを終了せずに電源を切ると、エディットし た内容が失われてしまいます。 保存するリズムパターンの確認 作成したリズムパターンは、15種類のセクションをまとめて、1
リズムパターンプログラムを終了する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● どのページでも、リズムパターンプログラムを終了できます。 1 パネル上の[PATTERN]ボタンを押します。 リズムが鳴っているときに[PATTERN]ボタンを押した場合、リズムは自動的に止 まります。 つくったリズムパターンがすでに保存されている場合は、そのままリズムパターン プログラムを終了します。 リズムパターンがまだ保存されていない場合には、保存せずに終了してよいか確認 を求めるメッセージが現れます。 2 [終了]ボタンを押すと、作成中のリズムパターンを保存せずにリズムパターン プログラムを終了します。[キャンセル]ボタンを押すと、終了せずに前の画面 に戻ります。 リズムパターンプログラムを終了すると、画面の左上が数秒間、水色に点灯し、 エディット内容を保存していることを示します。点灯中は電源を切らないでくだ さい。 保存したユーザーリズムを呼び出す ● ● ● ● ● ● ● ● ● ● ● ● ●
外部メディアからパターンを読み込む ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● スマートメディアやフロッピーディスクなどの外部メディアに保存されたパターンを読み 込んで、ユーザーリズムとして保存して使用できます。エレクトーン用のデータだけでな く、ほかの楽器でつくったパターンファイルも読み込むことができます。 1 2 3 4 読み込みたいパターン(パターンファイル)が入ったメディアを、挿入口に差し込み ます。 パネル上の[PATTERN]ボタンを押します。 画面右上の[ファイル]ボタンを押して、ファイルページを表示させます。 リズム再生中にファイルページを表示させると、リズムは自動的に止まります。 [選択]ボタンを押して、読み込みたいパターンファイルを選択します。 ファイルの選び方は、MDR機能のフォルダー選択と同じです。101ページ「メディ アやフォルダーを変更するには」をご覧ください。 5 9 [実行]ボタンを押すか、選択されているファイルをもう一度押して、パターン を楽器に読み込
キットリスト ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● C-1 C -1 D-1 D -1 E-1 F-1 G-1 A-1 F -1 G -1 A -1 B-1 C0 C 0 D0 D 0 E0 F0 G0 A0 下 鍵 盤 F 0 G 0 A 0 B0 C1 C 1 D1 D 1 E1 F1 G1 A1 F 1 G 1 A 1 B1 C2 C 2 D2 D 2 E2 F2 G2 A2 9 F 2 G 2 A 2 B2 リ ズ ム プ ロ グ ラ ム C3 C 3 D3 D 3 E3 F3 G3 A3 F 3 G 3 A 3 B3 上 鍵 盤 C4 C 4 D4 D 4 E4 F4 G4 A4 F 4 G 4 A 4 B4 C5 C 5 D5 D 5 スタンダードキット1 ライブ! スタンダードキット ライブ! Std.
C-1 C -1 D-1 D -1 E-1 F-1 G-1 A-1 F -1 G -1 A -1 B-1 C0 C 0 D0 D 0 E0 F0 G0 A0 下 鍵 盤 F 0 G 0 A 0 B0 C1 C 1 D1 D 1 E1 F1 G1 A1 F 1 G 1 A 1 B1 C2 C 2 D2 D 2 E2 F2 G2 A2 F 2 G 2 A 2 B2 C3 C 3 D3 D 3 E3 F3 G3 A3 F 3 G 3 A 3 B3 上 鍵 盤 C4 C 4 D4 D 4 E4 F4 G4 A4 F 4 G 4 A 4 B4 C5 C 5 D5 D 5 アナログキット ダンスキット ジャズキット ブラッシュキット ライブ! ブラッシュキット ライブ! ブラッシュ +Pキット シンフォニーキット ELキット1 スルドミュート スルドオープン ハイQ ホイップスラップ スクラッチH スクラッチL フィンガースナップ クリックノイズ メトロノームクリック メトロノームベル SeqクリックL SeqクリックH ブ
ELキット2 C-1 C -1 D-1 D -1 E-1 F-1 G-1 A-1 F -1 G -1 A -1 B-1 C0 C 0 D0 D 0 E0 F0 G0 A0 下 鍵 盤 F 0 G 0 A 0 B0 C1 C 1 D1 D 1 E1 F1 G1 A1 F 1 G 1 A 1 B1 C2 C 2 D2 D 2 E2 F2 G2 A2 F 2 G 2 A 2 B2 9 C3 C 3 D3 D 3 E3 リ ズ ム プ ロ グ ラ ム F3 G3 A3 F 3 G 3 A 3 B3 上 鍵 盤 C4 C 4 D4 D 4 E4 F4 G4 A4 F 4 G 4 A 4 B4 C5 C 5 D5 D 5 マラカスハイ スルドミュート マラカスロー スルドモフ スルドリム クイーカハイ スルドオープン クイーカミドル タンボリンミュート クイーカロー タンボリンオープン パンデイロ ボンゴハイ コンガスライド ボンゴロー コンガスラップ コンガモフ ボンゴミュート コンガハイ ボンゴスラップ コンガロー ティン
リズムを自動で切り替える: 3 リズムシーケンスプログラム リズムシーケンスプログラムを使えば、自分で作ったユーザーリズムや、エレクトーンに 内蔵されているリズムを1小節ずつ自由に組み合わせて、完成されたリズム譜として1曲分 のデータ(リズムシーケンス)を作ることができます。 リズムシーケンスは、パネル上の4つのシーケンスボタンに、それぞれ140小節まで保存 できます。複数のボタンに入ったデータを連続して再生することができるので、必要に応 じてデータを分けておけば、次のような使い方ができます。 ● 何曲かをメドレー形式で演奏する場合に、1曲ごとに別のシーケンスボタンにシーケン スデータを保存します。曲別に練習したいときに、目的の曲だけを再生できます。 ● 1曲をいくつかの部分に分けて、イントロをシーケンス[1]ボタン、Aメロを[2]ボタン、 サビを[3]ボタンなどと、それぞれ別のシーケンスボタンに保存しておきます。サビを練 習したいときには[3]ボタンを再生すれば、すぐに目的の場所から演奏が始められます。 リズムシーケンスプログラムを始める ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
2 画面上のメニュー [シーケンス1]〜[シーケンス4]ボタンを押して、シーケンス プログラムを保存したいシーケンスナンバーを選びます。 シーケンスナンバーを選ぶと、パネル上のシーケンスボタンのランプが点灯します。 RHYTHM SEQ. SEQ. 1 2 SEQ. SEQ. 3 4 MARCH WALTZ SWING& JAZZ LATIN WORLD MUSIC BALLAD または、パネル上のシーケンスボタン[SEQ.1]〜[SEQ.
3 4 リズムメニューの中から、入力したいリズムを選びます。 パネル上のボタンで、入力したいセクション(メインA〜D、フィルインA〜D、 NOTE イントロセクションを入力する場 イントロ1〜3、エンディング1〜3、ブレイク)を選びます。 合、入力するセクションの小節数 選んだリズムは、画面上部の中央に表示されます。 を画面上部で確認し、その小節数 だけセットしてください。 5 画面の[セット]ボタンを押します。 選んだリズムが1小節だけ入力され、画面上にボックスで表示されます。リズムを入 力すると、カーソルが自動的に1つ進み、次のリズムを入力できる状態になります。 ひとつのシーケンスボタンに、140小節までのリズムが入力できます。エンディン グを入力する場合は、エンディングパターンがすべて入力されます。(たとえば、 2小節のエンディングパターンの場合は、[セット]を押すと2小節分入力されます。) エンディングを入力したあとの小節には、シーケンスは入力できません。 6 手順2〜5の操作を繰り返して、リズムを入力していきます。 9 リズムシーケンスプログラムの途中で電源を切ると、入力
リズムシーケンスを試聴する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● シーケンスプログラムの途中で、作成中のシーケンスを試聴できます。 1 シーケンス再生させたい位置までカーソルを移動します。 カーソルの移動は、データコントロールダイアルまたは画面のポジションボタンで 行ないます。 DATA CONTROL 2 リズムの[START]ボタンを押します。 SYNCHRO START START BREAK これで、シーケンス再生が始まります。試聴をストップするには、もう一度リズム の[START]ボタンを押します。 9 入力したリズムシーケンスを編集する リ ズ ム プ ロ グ ラ ム ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● すでに入力したリズムの間に違うリズムを挿入したり、入力してあるリズムを削除したり できます。 1 178 ELS-01/01C/01X
1 ポジション 編集画面にあるカーソル(オレンジ色表示)を移動するボタンです。カーソルは、自分で設定 したリズムシーケンスの小節内で移動させることができます。 カーソルを最初の位置に戻します。 カーソルを1つだけ左に移動します。 カーソルを1つだけ右に移動します。 カーソルを5つ右に移動します。 2 データ リズムシーケンスデータの設定、編集作業をします。 セット 初めてリズムを入力するときや、カーソルの位置にあるリズムを別のリズムに置き 換える場合に使います。 [セット]ボタンを押すと、カーソルの位置に、現在リズムメニューで選ばれているリ シーケンスの途中にエンディン グパターンを挿入すると、それ 以降のシーケンスは自動的に削 除されます。 ズムを入力します。ただし、エンディングパターンの途中にある小節を別のリズム に置き換えることはできません。 挿入 カーソル位置の前にリズムを挿入する場合に使います。カーソルを、挿入したいと ころの次のリズムの位置に合わせます。挿入したいリズムをリズムメニューで選択 したあと、[挿入]ボタンを押します。カ一ソルの直前に、挿入したリズムが表示さ れ、カ一ソルの位置以降の
レジストレーションシーケンスをつくる ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● レジストレーションシーケンスは、「何小節目のどのタイミングで、レジストレーションが 何番に切り替わる」という情報をプログラムする機能で、リズムシーケンスの一部として 保存されます。レジストレーションシーケンスのデータをつくっておくと、リズムシーケ ンスを再生したときに、自動的にレジストレーションも切り替わります。フットスイッチ でレジストレーションを切り替える必要がなくなり、演奏に専念できます。また、レジス トレーションシーケンスの中にネクストレジストをプログラムすることもできます。 1 NOTE 画面右上の[レジスト]ボタンを押して、レジストページを表示させます。 リズムの再生中にレジストレー ションを読み込むと、シーケンス データやユーザーリズムは読み込 まれません。 レジストページで、レジストレーションシーケンスをプログラムします。入力され たレジストレーションは、画面の中央に横一列に表示されます。 2
4 画面のデータ[セット]ボタンを押します。 選んだレジストレーションが入力され、小節/拍/クロックの早い方から順に画面上 に表示されます。レジストレーションを入力すると、カーソルが自動的に1つ進み、 次のレジストレーションを入力できる状態になります。140までのレジストレー ションが入力できます。 複数のレジストレーションを同じ小節/拍/クロックに入力すると、最後に入力した レジストレーションが有効になります。 5 2〜4の操作を繰り返して、レジストレーションシーケンスを入力します。 ネクストレジストを入力する: レジストレーションシーケンスにネクストレジストのデータを入力しておくと、MDRで再 生しているソングに入っている次のレジストレーションを自動的に読み込みます。 1 ネクストレジストを入力したいバー (小節)/ビート(拍)/クロックを設定します。 ボタンやデータコントロールダイアルを使ってバー /ビート/クロックを 設定します(1拍=96クロックです)。 2 画面のネクストレジスト[挿入]ボタンを押します。 1で設定した位置にネクストレジストが入力され、小節/拍/クロックにそって画面
3 レジストレーションナンバーのタイミングを変更する場合は、画面のデータ [セット]ボタンを、ネクストレジストのタイミングを変更する場合は、画面の ネクストレジスト[セット]ボタンを押します。 タイミングが変更され、画面上に表示されるレジストレーションまたはネクストレ ジストは、小節/拍/クロックにそって並びます。 レジストレーションまたはネクストレジストを削除する: 1 ポジションボタンを使って、削除したいレジストレーションナンバーまたはネ 2 画面のデータ[削除]ボタンを押します。 クストレジストにカーソル(オレンジ色表示)を移動させます。 リズムシーケンスプログラムを終了する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● どのページでも、リズムシーケンスプログラムを終了することができます。リズムシーケ ンスプログラムを終了すると、それまでに作成したシーケンスは、自動的に保存されます。 リズムシーケンスプログラムを終了するには: パネル上の[SEQUENCE]ボタンを押します。
リズムシーケンスを再生する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● リズムシーケンスを再生するには: 1 シーケンスの入っているシーケンスボタン([SEQ.1]〜[SEQ.4])を押します。 SEQ.ボタンのランプが点灯します。 RHYTHM VOLUME MAX SEQ. SEQ. 1 2 SEQ. SEQ.
左フットスイッチを使って、シーケンスをスタートさせるには: 左フットスイッチを使ってリズムシーケンスのデータを再生することもできます。 1 2 3 4 使用したいすべてのSEQ.ボタンを押して、ランプを点灯させます。 [FOOT SWITCH]ボタンを押してフットスイッチ画面を呼び出し、レフトペー ジを表示させます。 モードを[リズム]にし、リズム設定で[停止]を選びます。 (フットスイッチの詳細については、185ページをご覧ください。 ) 左フットスイッチを右足で軽く押します。 これでリズムシーケンスがスタートします。リズムシーケンスの再生中に左フット スイッチを押すとリズムは停止します。 複数のシーケンスボタンを使用している場合、フットスイッチでリズムシーケンス をいったんストップさせたあと、もう一度フットスイッチでスタートさせると、次 のシーケンスボタンの最初から再生されます。 (たとえば[SEQ.1]、[SEQ.2]の2つ をオンにした場合、[SEQ.1]の途中にフットスイッチでストップさせて、そのあと で再スタートすると、[SEQ.
10 フットスイッチ/ニーレバー / エクスプレッションペダル FOOT SWITCH, KNEE LEVER AND EXPRESSION PEDAL フットスイッチやニーレバー、エクスプレッションペダルを使用すると、演奏中に右足を使っていろいろな機能を操作 したり、エフェクトのオン/オフを切り替えたりできます。手を使ってレジストレーションやリズムなどを切り替える必 要がなくなるので、演奏に専念できます。 この章の内容 1 フットスイッチ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 • リズムをコントロールする . . . . . . . . . . . . . . . . . . . . . . 186 • グライドをコントールする . . . . . . . . . . . . . . . . . . . . . . 187 • ロータリースピーカーをコントロールする . . . . . . . . . . 188 2 ニーレバー . . . . . . . . . . . . . . . . . . . . . .
DISPLAY SELECT VOICE DISPLAY A.B.C. M.O.C. MDR FOOT SWITCH UTILITY INTERNET RHYTHM PROGRAM VOICE EDIT PATTERN SEQUENCE U.ORGAN FLUTES L.
4 イントロ1〜3 フットスイッチを押すと、パネル上のINTRO [1]〜[3]ボタンを押したときと同じ効果が得 られます。 5 エンディング1〜3 フットスイッチを押すと、パネル上のENDING [1]〜[3]ボタンを押したときと同じ効果が 得られます。 グライドをコントールする ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 左フットスイッチでグライド効果をコントロールします。 1 2 フットスイッチを押すと、上鍵盤/下鍵盤の音群ごとに音色のピッチを半音下げます。 フットスイッチから足をはなすと、ゆるやかに元の音程に戻ります。 1 上鍵盤1/上鍵盤2/リード1/リード2/下鍵盤1/下鍵盤2 グライドをかけたい音群を選択します。複数の音群をオンにしておくこともできます。 2 タイム フットスイッチから足をはなしたときに、音程が戻る速さを設定します。設定値を大きく すると、音程が戻る速さは遅くなります。 10 設定範囲:1〜5 フ ッ ト ス イ ッ チ / ニ ー レ バ ー / エ ク
ロータリースピーカーをコントロールする ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 関連ページ 左フットスイッチで、ロータリースピーカーのオン/オフを切り替えます。 ロータリースピーカー (51ページ) ここで[ロータリースピーカー ]ボタンを選んで、フットスイッチを押すと、パネル上の [ROTARY SP SPEED]ボタンを押したときと同じ効果が得られます。この機能を使うた めには、あらかじめ、それぞれの音群やオルガンフルート音色で、ロータリースピーカー が正しく設定されていることが必要です。詳しくは、51ページをご覧ください。 2 ニーレバー 鍵盤下にあるニーレバーは、上鍵盤と下鍵盤のサステイン、メロディオンコード、リード スライド効果、ソロ機能の切り替えをコントロールします。 サステインをコントロールする ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 上鍵盤と下鍵盤のサステインを
3 演奏中にサステインをかけたいところで、右足でニーレバーを右に押します。 押している間だけ、サステインがかかります。ニーレバーを押すのをやめると、 サステインはかからなくなります。 1 ニーレバーがたたんである場合: パネルのサステインボタンがオンになっていると、サステインがかかります。 2 ニーレバーが垂直の場合: パネルのサステインボタンがオンになっていても、サステインはかかりません。 3 ニーレバーが右に押されている場合: パネルのサステインボタンがオンになっていると、サステインがかかります。 1 (オン) (オフ) (オン) 2 3 メロディオンコードをコントロールする ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 1 2 [A.B.C./M.O.C.
リードスライドをコントロールする ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 関連ページ ボイスコンディション画面 (42ページ) 1 2 3 リードスライドをかけたいリードボイスの、ボイスコンディション画面2ページ 目を表示させます。 スライドの[ニーレバー ]ボタンを選択します。 演奏中にスライドをかけたいところで、右足でニーレバーを右に押します。 押している間だけ、リードボイスにスライドがかかります。ニーレバーを押すのを やめると、リードスライドはかからなくなります。 ソロ機能をコントロールする ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● リードボイス2のソロ機能を、ニーレバーでオン/オフできます。 29ページをご覧ください。 3 エクスプレッションペダル 10 エクスプレッションペダルは、演奏中に音の強弱をコントロールします。また、ELS関連ページ フ ッ ト ス
1 [UTILITY]ボタンを押します。 ユーティリティ画面が表示されます。 2 画面右上の[EXP.](エクスプレッション)を押して、エクスプレッションページ を表示させます。 DISPLAY SELECT VOICE DISPLAY A.B.C. M.O.C. MDR FOOT SWITCH UTILITY INTERNET RHYTHM PROGRAM VOICE EDIT PATTERN SEQUENCE U.ORGAN FLUTES L.
値が12 (WIDE:ワイド=広い)の場合は、セカンドエクスプレッションペダルを踏み込んだ ときに1オクターブの範囲でピッチを変化させます。 2 ピッチベンド ピッチベンドをコントロールしたい音群をONにします。ピッチベンドは、上鍵盤ボイス1、2、 リードボイス1、2、ペダルボイス1、2にかかります。 リズムテンポをコントロールする ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 1 2 1 モード リズムテンポの変化の幅を設定します。 設定範囲:1〜12 値が2 (NARROW:ナロー =狭い)の場合は、セカンドエクスプレッションペダルを踏み込ん だときに、テンポを70%〜140%の範囲で変化させます。 値が12 (WIDE:ワイド=広い)の場合は、セカンドエクスプレッションペダルを踏み込んだ ときに、テンポを50%〜200%の範囲で変化させます。 2 テンポ セカンドエクスプレッションペダルでリズムテンポをコントロールする場合は、ここをON 10 にします。 フ ッ ト ス イ ッ チ /
11 トランスポーズ/ピッチ TRAN SP O SE A ND PI T CH エレクトーンの音程を変更する機能として、半音ずつ移調するトランスポーズと、音程の微調整をするピッチがあります。 ユーティリティ画面で、トランスポーズやピッチに関する設定を行ないます。(ここでの設定はMDRに記録することは できません。) 1 2 [UTILITY]ボタンを押します。 ユーティリティ画面が表示されます。 画面右上の[ピッチ]ボタンを押して、ピッチページを表示させます。 DISPLAY SELECT VOICE DISPLAY A.B.C. M.O.C. MDR FOOT SWITCH UTILITY INTERNET RHYTHM PROGRAM VOICE EDIT PATTERN SEQUENCE U.ORGAN FLUTES L.
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ピッチとチューニング オーケストラのように複数の人数で楽曲を演奏するときには、かならず演奏前に「チューニ ング」と呼ばれる作業を行ないます。たとえば、A (ラの音)を演奏したときに435Hz (ヘル ツ)の音を出す楽器、440Hzの音を出す楽器、445Hzの音を出す楽器を同時に演奏すると、 不協和音になってしまいます。 こんなことがおこらないように各楽器のピッチをそろえる作業が「チューニング」です。楽 器によって「調律」「調弦」などと呼ばれることもあります。 チューニングの方法は、大きく分けて2通りあります。 1つめは、奏者ひとりひとりが自分の楽器を決められたピッチに合わせる方法。音叉や チューニングメーターなどを使って正確なピッチに合わせます。ギター合奏などはこの方法 で行なうことが多いでしょう。たとえばロックバンドの場合は、ギタリストとベーシストが それぞれの楽器を「A=440Hz」に合わせておきます。する
12 インターネットダイレクト接続機能 IN TER N ET D I R E CT CO NNECT I O N インターネットダイレクト接続機能では、楽器から直接インターネット上のエレクトーン専用サイトにアクセスして、 曲データを購入したり、ウェブページを閲覧したりできます。購入した曲データは、スマートメディアまたはUSBフ ラッシュメモリーに保存できます。この章では、コンピューターや通信規格に関する用語が出てきます。わからない用 語が出てきたら、210ページの「インターネット用語辞典」をご覧ください。 この章の内容 1 楽器をインターネットに接続する . . . . . . . . . . . . . . . 195 2 エレクトーン専用サイトを見る . . . . . . . . . . . . . . . . . 196 • 画面をスクロールする . . . . . . . . . . . . . . . . . . . . . . . . . . 197 • リンクをたどる. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
接続例2:有線で接続する(ルーター機能のついているモデムを使用) NOTE ADSLモデム モデムの種類によっては、複数 LANケーブル ルーター機能あり の機器(コンピューターと楽器な ど)を接続するために、別途ハブ LANケーブル が必要な場合もあります。 USB-LANアダプター 接続例3:無線で接続する モデム* ルーター アクセス ポイント USB無線LANアダプター *モデム=ADSLモデム、ONU (光ネットワークユニット)、ケーブルモデム 2 エレクトーン専用サイトを見る 楽器がインターネットに正しく接続された状態で[INTERNET]ボタンを押すと、エレクトーン 専用サイトのトップページが表示され、エレクトーンのデータを購入したり、試聴したりする ことができます。(エレクトーン専用サイトをご覧いただくためには、ユーザー登録が必要で す。詳しくは、サイト内の説明をお読みください。 ) DISPLAY SELECT A.B.C. M.O.C.
画面の左側のコントロールメニューでは、表示するウェブページを操作したり、インター ネット機能の設定を行なったりします。画面の右側のブラウザーは、ウェブページの内容 を表示する部分です。 エレクトーンの電源を入れたあと、はじめてインターネット機能に入ったときにブラウ ザーに表示される画面を「ホームページ」といいます。ほかのウェブページからホーム ページに戻る場合は、コントロールメニューの[ホーム]ボタンを押します。 関連ページ ホームページを変更する (204ページ) 画面をスクロールする ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ウェブページのサイズが大きくてブラウザーに収まらない場合は、ブラウザーの右端や下 辺にスクロールバーが表示されます。スクロールバーに直接触って画面をスクロールさせ ると、隠れていた部分を表示させることができます。 リンクをたどる ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
通信状態について コントロールメニューの上には、インターネット接続の状況に応じて、アイコンやメッ セージが表示されます。 1234 5 1 オフライン表示( ) 楽器がインターネットに接続されていないときに表示されます。このアイコンが表示さ れている状態では、ウェブページを見ることができません。 2 通信中表示( ) ウェブページを読み込んでいるときに点滅し、通信中であることを示します。読み込み が終わると点灯します。 3 SSL表示( ) SSLを使用しているウェブページを表示しているときに点灯し、情報が暗号化されて 通信されていることを示します。 4 無線LANの電波表示 無線LANでインターネットに接続している場合に、電波の強さ(受信状態)が表示されま す。電波が弱い(または届かない)ときは、エレクトーンをアクセスポイントの近くに移 動し、電波が届く状態にしてください。 強 中 弱 (インターネットに接続できない場合があります) 圏外 (インターネットに接続できません) 5 ウェブページの読み込み状態表示 ウェブページの読み込み状態に応じて、以下の3つのメッセージが表示されます。 1
ページを更新/キャンセルする ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 現在表示されているウェブページを最新の情報に更新するには、コント ロールメニューの[更新]ボタンを押します。 ウェブページの表示に時間がかかる場合や、ウェブページの読み込み中に そのウェブページの表示をキャンセルしたい場合には、コントロールメ ニューの[中止]ボタンを押します。 直前に表示していたウェブページへ移動する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 直前に表示していたウェブページに戻るには、コントロールメニューの [戻る]ボタンを押します。 [戻る]ボタンを押す前に表示していたウェブページに戻るには、コントロー ルメニューの[進む]ボタンを押します。 文字を入力する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
試聴中の操作: 参考演奏の試聴中には、次のような画面が表示され、特定のパートをミュートしたり、テ ンポを変更したりできます。詳しくは117ページをご覧ください。 [ K](一時停止) ボタンや[J](停止)ボタンを押すと、再生が中断/停止されます。再生を 停止した状態で鍵盤を弾くと、各鍵盤のボイスを確認することができます。[ F](再生)ボ タンを押すと、再び参考演奏の再生が始まります。何度でも試聴できます。試聴を終了し てもとのエレクトーン専用サイトに戻るには、[試聴終了]ボタンを押します。 購入(ダウンロード)後の操作: 購入(ダウンロード)したデータは、スマートメディアまたはUSBフラッシュメモリーに保 NOTE ID付きのスマートメディアまた はUSBフラッシュメモリーが必 存できます。ウェブページ上でデータ購入の操作をすると、購入(ダウンロード)したデータ をどこに保存するか選択する画面が表示されます。保存先フォルダーを選んで、[保存]ボタ ンを押すと、ダウンロードが実行されます。 要です。 NOTE 保存ボタンを押す前に[閉じる]ボ タンを押して画面を閉じると、 データがダウンロードされず
表示されているウェブページをブックマーク(お気に入り) に登録する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ブラウザーに表示されているウェブページを、お気に入りとしてブックマークに登録するこ とができます。ブックマークに登録したウェブページは、すぐに呼び出すことができます。 1 ブックマークに登録したいウェブページが表示されている状態で、コントロー ルメニューの[ブックマーク]ボタンを押します。 ブックマーク画面が表示され、現在登録されているブックマークが一覧表示されま す。一覧表示の下には、ブックマークに登録するウェブページのタイトルが表示さ れます。 2 コントロールメニューの[追加]ボタンを押します。 コントロールメニューの表示が変わり、新たにブックマークを登録できる状態にな ります。 ウェブページのタイトル 12 ELS-01/01C/01X 取扱説明書 201 イ ン タ ー ネ ッ ト ダ イ レ ク ト 接 続 機 能
3 ブックマークリストで、ブックマークを登録する場所を選択します。 ブックマークリストに直接触るか、データコントロールダイアルまたは[カーソル上 移動]、[カーソル下移動]ボタンを使って、ブックマークを登録する場所を選びます。 ここで選んだ位置に、ブックマークが登録されます。右側のスクロールボタンで、 表示をスクロールさせることもできます。 DATA CONTROL 4 コントロールメニューの[実行]ボタンを押します。 表示していたウェブページがブックマークに登録され、手順1のブックマーク画面に 戻ります。 [中止]ボタンを押すと、ブックマークに登録せずにブックマーク画面に戻ります。 5 12 イ ン タ ー ネ ッ ト ダ イ レ ク ト 接 続 機 能 202 ELS-01/01C/01X 取扱説明書 コントロールメニューの[閉じる]ボタンを押して、ブラウザー画面に戻ります。
ブックマークに登録したウェブページを表示するには: 1 2 ブックマーク画面で、表示させたいブックマークを選びます。 コントロールメニューの[ジャンプ]ボタンを押します。 自動的にブックマーク画面が閉じ、ブックマーク画面で選択したウェブページが ブラウザーに表示されます。 ブックマークを編集する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ブックマーク画面では、ブックマークのタイトルを変更したり、登録を削除したり、順番 を入れ替えたりできます。 1 2 3 4 5 6 7 1 カーソル上移動/カーソル下移動 ブックマークリスト内の選択位置を移動します。 2 ジャンプ ブックマークリストで現在選ばれているウェブページをブラウザーに表示します。 3 追加 ブックマークに登録するときに使用します。201ページをご覧ください。 4 タイトル変更 現在選ばれているブックマークのタイトルを変更します。このボタンを押すと、文字入力 画面が表示されます。文字入力について詳しくは、107ページをご覧ください。
6 移動 ブックマークの順番を入れ替えます。 1 位置を移動したいブックマークを選んだあと、[移動]ボタンを押します。 コントロールメニューの表示が変わり、選択したブックマークを移動できる状態に なります。 2 ブックマークリストで、ブックマークを移動する場所を選択します。 ブックマークリストに直接触るか、データコントロールダイアルまたは[カーソル上 移動]、[カーソル下移動]ボタンでブックマークを移動する場所を選びます。 3 コントロールメニューの[実行]ボタンを押します。 選択したブックマークが移動し、ブックマーク画面に戻ります。 7 閉じる ブックマーク画面を閉じ、ブラウザー画面に戻ります。 ホームページを変更する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 初期状態では、エレクトーン専用サイトがホームページとして登録されていますが、現在 表示されているウェブページをホームページとして登録することで、よく使うページを ホームページに指定することもできます。 1 2 3 12 イ ン
3 環境設定画面について 環境設定画面では、インターネット接続に関する設定や、ブラウザーや文字入力画面の表 示方法などの、さまざまな設定を行ないます。環境設定画面は、ブラウザー、LAN、無線 LAN、その他の4つのページで構成されています。 ブラウザーページ ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 1 2 3 4 5 6 7 1 エンコード ブラウザーに表示される文字コードを設定します。 2 ホームページ ホームページとして登録されているウェブページのタイトルを表示/編集します。 3 ページをホームに登録 204ページ「ホームページを変更する」をご覧ください。 4 ホームを初期状態に戻す [初期状態に戻す]ボタンを押すと、ホームページの設定が工場出荷時の状態に戻ります。 5 画像データの読み込み [オン]にすると、ウェブページ内の画像データをブラウザー上に表示します。[オフ]にする と、画像データは表示されません。 6 ソフトキーボード配列 [ABC順配列]を選ぶと、アルファベットを入力すると
LANページ ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 設定をメモしておきましょう。 1 2 DHCPの使用 DNSサーバー 1 3 DNSサーバー 2 IPアドレス サブネットマスク ゲートウェイ LAN(ラン)の環境設定を行なうページです。有線で接続する場合だけでなく、無線で接続す る場合にもここでの設定が必要です。詳しくは、接続機器(ルーターなど)の設定をご確認い ただくか、インターネットプロバイダーにご確認ください。 1 DHCPの使用 DHCPを使用するかどうか設定します。使用しているルーターがDHCPに対応している場 合は、[使用する(DNSを自動設定)]を選びます。 2 DNSサーバー 1/DNSサーバー 2 プライマリー DNSサーバー /セカンダリー DNSサーバーのアドレスを設定します。 DHCPの使用(1)で[使用する(DNSを手動設定)]または[使用しない]を選んだ場合、ここで の設定が必要です。設定内容については、ルーターの取扱説明書などをご確認ください。 3 IP
無線LANページ ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 設定をメモしておきましょう。 1 2 3 4 5 SSID チャンネル Ch 暗号化 □ する □ しない 暗号キーの形式 □ ASCII □ 16進数 暗号キーの長さ □ 64bit □ 128bit 暗号キー 無線LAN(ラン)の環境設定を行なうページです。アクセスポイント側で設定している内容と 同じに設定してください。アクセスポイントの設定の確認/変更については、アクセスポイ NOTE WEP以外の暗号化形式で暗号化 ント(無線LAN親機)の取扱説明書をご覧ください。 されたアクセスポイントは、使 用できません。 1 アクセスポイント [表示する]ボタンを押すと、エレクトーンの近くにあるアクセスポイントの一覧が表示され NOTE アクセスポイントから電波が届 ます。 かない場合は、表示されません。 一覧の中から所有するアクセスポイントを選んで[OK]を押すと、アクセスポイントの設定 をエレクト
その他ページ ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 1 2 3 4 5 1 プロキシサーバー /プロキシポート/プロキシを使わないサーバー NOTE プロキシを使わないサーバーを 複数設定する場合は、コンマ( , ) プロキシサーバーの名前、ポート番号、プロキシを使用しないサーバー名を設定します。 プロキシを使用する場合のみ、ここでの設定が必要です。 で区切って入力してください。 2 クッキーの削除 [削除する]ボタンを押すと、保存されているクッキーの設定がすべて削除されます。 3 ブックマークの全削除 [削除する]ボタンを押すと、登録されているブックマークがすべて削除されます。 4 環境設定の初期化 環境設定画面で行なったすべての設定項目を、工場出荷時の状態に戻します。209ページ 「インターネット設定の初期化」をご覧ください。 5 接続情報 [接続情報]ボタンを押すと、現在の接続情報の詳細が確認できます。 12 イ ン タ ー ネ ッ ト ダ イ レ ク ト 接 続 機 能 20
4 インターネット機能を終了する パネル上のボイスボタンやリズムボタンなどを押すと、インターネットダイレクト接続機 能は終了し、インターネットへの接続は自動的に切断されます。もういちど[INTERNET] ボタンを押すと、自動的にインターネットに接続され、前回開いていたウェブページが表 示されます。 5 インターネット設定の初期化 インターネットダイレクト接続機能の設定は、エレクトーンの初期化(23ページ)では初期 化されません。ここで説明する方法で初期化する必要があります。初期化を実行すると、 環境設定画面で行なったすべての設定が工場出荷時の状態に戻ります。 1 2 3 4 コントロールメニューの[環境設定]ボタンを押します。 環境設定画面が表示されます。 画面右上の[その他]ボタンを押して、その他ページを表示させます。 [初期状態に戻す]ボタンを押します。 初期化してよいかどうか確認を求める画面が表示されます。 12 [はい]を選択すると、設定を初期化します。[いいえ]を選択すると、初期化せず にもとの画面に戻ります。 ELS-01/01C/01X 取扱説明書 209 イ ン タ ー
6 インターネット用語辞典 12 イ ン タ ー ネ ッ ト ダ イ レ ク ト 接 続 機 能 210 インターネット コンピューター間の通信規格にもとづいて、世界中のコンピューターや携帯電話などを接続した、 巨大な ネットワークのこと。 ウェブページ サイトを構成する各ページのこと。 クッキー (Cookie) ユーザーがウェブページとの間でやりとりした内容を記憶するしくみ。以前訪れたウェブページで、 そのと きに入力した内容があらかじめ表示されるのはこのしくみによるもの。 ゲートウェイ ネットワーク上で、通信規格の異なるデータを相互に変換してやりとりするためのシステム。 サイト 正式には「ウェブサイト」という。ひとまとまりに公開されているウェブページ群。たとえば、 "http:// www.yamaha.co.
13 外部機器との接続 C ON N EC T IO N S このエレクトーンには、鍵盤の下側にいろいろな端子があります。左側には入/出力端子があり、CDの再生音やマイク からの音声を入力したり、エレクトーンの音をヘッドフォンや外部のスピーカーやステレオ機器から出力したりできま す。右側にはUSB端子やMIDI端子があり、エレクトーンとコンピューターをつないでデータをやり取りしたり、エレ クトーンでほかの楽器をコントロールしたりできます。また、ELS-01Xには、ペダルユニットにも出力端子がありま す。 この章の内容 1 付属端子の名称と機能 . . . . . . . . . . . . . . . . . . . . . . . . 211 2 外部機器との接続 . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 • スピーカーから音を出さずヘッドフォンで音を聞く. • エレクトーンの音を外部スピーカーから出力する . . • エレクトーンの音をMDレコーダーなどに録音する .
5 6-1 AUX IN L / L+R R 7 AUX OUT L / L+R R AUX OUT L R (LEVEL FIXED) (ELS-01Xのみ) (LEVEL FIXED) R L R L AUX OUT 8 関連ページ CDやMDの音をエレクトーンの スピーカーから流す( 216ページ) 関連ページ 6-2 5 AUX INフォーン端子 L/L+R、R 外部機器からの音声信号をステレオ入力する端子です。入力された信号は、エレクトーン の音と一緒にエレクトーンのスピーカーから出力されます。 6 AUX OUTフォーン端子 6-1 AUX OUTフォーン端子 L/L+R、R エレクトーンの音を外部スピー カーから出力する(214ページ) エレクトーンの音声信号をステレオ出力する端子です。MASTER VOLUMEダイア エレクトーンの音をMDレコー ダーなどに録音する(216ページ) ルで音量を調節できます。 6-2 AUX OUTフォーン端子 L、R (LEVEL FIXED)(ELS-01Xのみ) エレクトーンの音声信号をステレオ出力する端子です。
) USB端子 ) - 1 USB TO DEVICE端子 (ELS-01: 1つ、ELS-01C/01X: 2つ) 関連ページ USB対応の記憶装置(フロッピーディスクドライブなど)を接続するための端子です。 また、インターネットダイレクト接続機能を使用する場合には、この端子を使って インターネットに接続します。 インターネットダイレクト接続 機能(195ページ) USB記憶装置やUSB-LANアダ プターを接続する(219ページ) ) - 2 USB TO HOST端子 コンピューターのUSB端子と接続するための端子です。USBケーブルを使って直接 接続できます(接続にはUSB-MIDIドライバーが必要です)。 コンピューターとの接続(220 ページ) USBとは USBとは、Universal Serial Bus (ユニバーサルシリアルバス)の略で、コンピュー ターと周辺機器を接続するためのシリアルインターフェースです。 ! MIDI IN/OUT端子 ほかのMIDI (Musical Instrument Digital Interface)規格の楽器と接続するための端子で す。エレクト
エレクトーンの音を外部スピーカーから出力する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● コンサートなどでは、エレクトーンの音をアンプ内蔵の外部スピーカーから鳴らすことが できます。AUX OUT端子を使用します。スピーカーを1台だけ使う場合は、AUX OUT フォーンL/L+R端子を使用します。 AUX OUT L/L+R R スピーカー(左側) スピーカー(右側) 接続例:ミキサーを使ったライブ演奏 エレクトーンをコンサートなどで使用する場合は、エレクトーンを直接外部スピーカー に接続するのではなく、エレクトーンとミキサーを接続し、ミキサーを外部スピーカー に接続するのが一般的です。 ミキサーを通すことで、他の楽器との間で音量/音質バランス調整が容易に行なえるよ うになり、調整することでまとまりのある演奏になります。 ミキサーとの接続には、エレクトーンのAUX OUT端子を使用します。 エレクトーンのAUX OUTには、MASTER VOLUMEダイアルに連動して出力レベル を調整できる
メインスピーカー (アンプ内蔵のパワードスピーカー等) モニタースピーカー 再生音 再生音 再生音 再生音 キーボード MUSIC PRODUCTION SYNTHESIZER AUX OUT マイク 再生音 ミキサー STAGEA 電源を入れる順番 電源オン/オフ時のノイズからスピーカーを保護するため、電源を入れる順番に気を配 りましょう。 電源を入れる前に、すべての機器のボリュームが絞られている(0になっている)ことを 確認し、以下の順序で電源を入れます。 (1)エレクトーンやキーボードなどの外部音源 (2)ミキサー (3)スピーカーアンプ(パワードスピーカー) 電源を切る場合は、すべての機器のボリュームを下げたあと、逆の順番(3→2→1) で切ってください。 13 ELS-01/01C/01X 取扱説明書 215 外 部 機 器 と の 接 続
エレクトーンの音をMDレコーダーなどに録音する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● エレクトーンの音をカセットテープやMDなどに録音できます。OPTICAL OUT端子を使 う方法と、AUX OUT端子を使う方法があります。OPTICAL OUT端子からは、エレク トーンの演奏がデジタル信号で出力され、音質劣化のない状態で録音できます。お使いの NOTE AUX IN端子からの入力音もいっ しょに録音する場合は、鍵盤の MDレコーダーなどの機器がOPTICAL INに対応している場合は、光デジタルケーブルを 使ってOPTICAL OUT端子と接続してください。また、AUX OUT端子を使用する場合は、 ケーブルの形状に合わせてピン端子、フォーン端子のどちらかに接続してください。 下にあるAUX OUTフォーン端子 を使用してください。 MD、カセットレコーダーなど MD、カセットレコーダーなど R LINE IN L OPTICAL IN AUX OUT L OPTICAL OU
マイクやギターをつないで使う ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● マイクを接続して弾き語りやカラオケを楽しんだり、ギターなどを接続してエレクトーン と一緒にアンサンブル演奏を楽しむことができます。MIC./LINE IN端子にマイクやギター などを接続して、エレクトーンのスピーカーから音を出します。 1 マイクやギターなどをMIC./LINE IN端子に接続します。 マイクを使用する場合はダイナミックマイクをご使用ください。 MIC./LINE IN 2 音声を入力する場合は、MIC./LINE切り替えスイッチをMIC.側に、ギターなど 出力レベルの高い機器を接続する場合はLINE側に切り替えます。 NOTE MIC. LINE MIC. LINE MIC.とLINEのどちらにするべき かわからない場合は、LINEの状 態で音を出してみて、音が小さ ければMIC.
ボリューム/リバーブを変更するには: 1 関連ページ リバーブ( 49ページ) 2 パネル上の[UTILITY]ボタンを押して、ユーティリティ画面を表示させます。 設定ページのマイクボリューム、マイクリバーブのスライダーで、ボリューム とリバーブの量を変更します。 ボリュームスライダーの値を最大にしても、INPUT VOLUMEつまみが最小になっ ていると、マイクの入力音声は聞こえません。また、リバーブスライダーの値を最 大にしても、パネル上のREVERBボタンが最小になっていると、リバーブはかかり ません。 エレクトーンから外部MIDI音源を鳴らす ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 関連ページ MIDIとは(221ページ) エレクトーンを演奏すると、接続先の機器もその機器の音色で同時に鳴らすことができま す。音に厚みを出すときなど便利です。(ただし、外部MIDI機器の受信チャンネルがエレク トーンの送信チャンネルと一致していることが必要です。) この他にもいろいろな演奏の動
外部MIDI機器からエレクトーンをコントロールする ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 外部のMIDIキーボードを演奏してエレクトーンを同時に鳴らしたり、シーケンサーからエ レクトーンにMIDI信号を送ってエレクトーンの音源を鳴らしたり、レジストレーションを 切り替えたりできます。(ただし、外部MIDI機器の送信チャンネルがエレクトーンの受信 NOTE MDR使用時は、外部機器からの MIDI信号は受信できません。 チャンネルと一致していることが必要です。) 外部MIDIキーボードやシンセサイザー MUSIC PRODUCTION SYNTHESIZER MIDI IN MIDI OUT MIDIケーブル メッセージ USB TO HOST端子を使用している場合は、MIDI端子は使用できません。 USB記憶装置やUSB-LANアダプターを接続する ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
3 コンピューターとの接続 USB端子、またはMIDI端子を使って、エレクトーンとコンピューターを接続できます。 エレクトーンとコンピューター間で直接MIDI信号を送受信できます (MIDIについては、 221ページをご覧ください)。実際にMIDI信号をやり取りするためには、お使いのコン ピューターに合ったMIDIドライバーが必要になります。 コンピューターと接続する前に、コンピューターにMIDIドライバーをインストールし ておいてください。最新のMIDIドライバーは、インターネット上のヤマハホームペー ジ
MIDI端子を使った接続 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● エレクトーンのMIDI端子を使って、コンピューターと接続できます。この場合は、MIDI NOTE ケーブルのほかに、MIDIインターフェースが必要です。MIDIインターフェースのMIDI お使いのMIDIインターフェース OUT端子とエレクトーンのMIDI IN端子を接続します。また、MIDIインターフェースの によっては、コンピューターの MIDI IN端子とエレクトーンのMIDI OUT端子を接続します。 シリアル端子と接続することも できます。 コンピューター IN OUT MIDI MIDI OUT MIDI IN MIDIインターフェース (UX16など) 4 MIDIに関する基礎知識 ここでは、エレクトーンが音を出す仕組みや、エレクトーンがコンピューターやほかの 楽器とどのようにデータをやり取りしているかについて説明します。 MIDIとは ● ● ● ● ● ● ● ● ● ● ● ● ● ●
前のイラストのように、電子楽器では演奏情報をもとに、音源部(電子回路)に記憶されてい るサンプリング音(あらかじめ録音されている音)が発音するのです。それでは、発音のもと になる演奏情報とはいったい何なのでしょうか? たとえば、エレクトーンの鍵盤で、グランドピアノの音色で「ド」の音を4分音符の長さで 強く弾いたとします。共鳴して音を出すアコースティック楽器と異なり、電子楽器は 「どのボイスで」 「どの鍵盤を」「どのくらいの強さで」 「いつ押さえたか」「いつはなした か」といった演奏情報を作り出します。そして、ひとつひとつの演奏情報は、数値に置き 換えて音源部に伝えられます。音源部ではその数値をもとに、記憶されているサンプリン グ音が鳴るのです。 演奏情報の例 ボイスナンバー (どのボイスで) 1(グランドピアノ) ノートナンバー (どの鍵盤を) 60(ド:C3) ノートオン(いつ押さえたか)& ノートオフ(いつはなしたか) タイミングを数値化(4分音符) ベロシティ (どのくらいの強さで) 120(強く) このようにエレクトーンでは、鍵盤演奏やボイス変更などのパネル操作のひとつひとつが MID
チャンネルメッセージ ● キー情報(ノートオン/ノートオフ/ベロシティ) 演奏に関わる最も重要な情報で、エレクトーンの鍵盤を弾いたときにこれらのメッセージ が送信されます。また、ほかのキーボードやシーケンサーなどからこれらの情報を送信し てエレクトーンを演奏させることができます。 ノートオン: このキーを押した、ということを示す情報です。弾いた音の高さを表すため に半音ごとに割り当てられた0〜127のノートナンバーが内部的には用いら れています。演奏時にノートナンバーを意識する必要はありませんが、エレ クトーンのC3の鍵盤を弾いたときにノートナンバー 60が送信されるように なっています。 ノートオフ: 鍵盤から指をはなした、ということを示す情報です。 ベロシティ: 鍵盤を弾いたときのタッチの強弱を示す情報です。 エレクトーンのキー情報や上鍵盤、下鍵盤に対応するノートナンバーについてはMIDIイン プリメンテーションチャート(250ページ)やMIDIデータフォーマット(238ページ)をご覧 ください。 ● プログラムチェンジ 音色を切り替えるための情報です。コンピューターやシーケンサーなどからこれらのメッ セ
MIDIチャンネル ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● MIDIの情報には、MIDIチャンネルという1〜16の番号が割り当てられています。この MIDIチャンネルを使って、1本のMIDIケーブルで同時に16パート用の情報を送るしくみに なっています。 MIDIチャンネルは、テレビのチャンネルと同じようなものだと考えることができます。テ レビの放送局は、あらかじめ割り当てられたチャンネルで情報を送信します。各家庭では 複数の放送局から送られてきた情報を同時に受信した上で、特定のチャンネルを選択する ことで目的の放送局の情報(番組)をみることができるわけです。 天気予報 NEWS 1 2 NEWS 2 MIDIチャンネルもこれと同じしくみです。MIDIメッセージは、送信側の楽器で設定された MIDIチャンネル(MIDI送信チャンネル)によってMIDIケーブルを通り受信側の楽器に送られ ます。このとき、受信側の楽器で設定されるMIDIチャンネル(MIDI受信チャンネル) が、送 信側のMI
5 MIDIコントロール エレクトーンをほかのMIDI機器やコンピューターと接続したときに、外部機器からどのよ うにエレクトーンをコントロールするか、またはエレクトーンからどのように外部機器を コントロールするかを設定します。送信チャンネルを選択したり、外部機器との同期設定 をしたりします。 1 2 [UTILITY]ボタンを押します。 ユーティリティ画面が表示されます。 画面右上の[MIDI]ボタンを押して、MIDIページを表示させます。 1 2 3 3-1 3 -2 3 -3 1 アウトプット MIDIの送信チャンネルを変えることができます。上鍵盤、下鍵盤、ペダル鍵盤のそれぞれ について、チャンネル1〜16のいずれかを設定できます。ここで設定した送信チャンネル で各鍵盤の演奏情報を送信することができます。MIDIメッセージを送信したい機器(コン ピューターやMIDI音源など)の受信チャンネルに合わせて、送信チャンネルを設定してくだ さい。 送信チャンネルボタンを押すと、チャンネル(CH)1〜16のリストが表示されます。その中 から設定したいチャンネルナンバーを選ぶと、自動的にリストが閉
3 インターナル/エクスターナル 表示された各項目のコントロールをエレクトーンで行なう(インターナル)か、外部機器で行 なう(エクスターナル)かを切り替えます。 3 - 1 リード1 リードボイス1の発音方法を設定します。 インターナル:リードボイス1は、上鍵盤(トゥーロワー機能をオンにした場合は下 鍵盤)で発音します。 エクスターナル:リードボイス1は、MIDIチャンネル4で外部から送信された演奏情 報を受けて、発音します。 3 - 2 同期 リズムを同期させるためのタイミング決定を、どの機器で行なうかを設定します。 通常はインターナルにします。 インターナル:エレクトーンのリズムの[START]ボタンや[SYNCRO START]ボタ ンを押すと、外部の接続機器(シーケンサーなど)のリズムがいっしょにスタートしま す。エレクトーンから外部機器をコントロールするための設定です。 エクスターナル:外部機器から送信された信号によって、エレクトーンのリズムを スタート/ストップします。外部機器からエレクトーンをコントロールするための設 定です。 3 - 3 エクスプレッション エクスプレッションペダルの機能をコン
14 付録 A PPEN DIX ELS-01/01C/01Xの分解/組み立て エレクトーンを分解/組み立てする前に、以下の手順を必ずお読みください。 分解せずに運搬する場合でも、必ずペダルユニットを外してください。ペダルユニットをつけたまま運ぶと、運搬中に傾いてペダルユニットが外 れるおそれがあります。 エレクトーンの分解手順 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 分解すると231ページの状態になります。 ■ ご注意 分解は、必ず2人以上で行なってください。 手をはさんだり、取り外したユニットを落としたりしないよう、必ず指定された位置を持ってください。 本体の分解には、大小2種類の六角レンチ(対面6mmと4mm、椅子の座面裏に付属)を使用します。六角レンチの使用方法については230ページを ご覧ください。 1 エレクトーンの電源を切り、電源プラグをコンセント から抜きます。 2 ペダルユニットを取り外します。 2-1 左右のサイド
2-4 ペダル鍵盤の下のフレームを持ち上げて左右の突起か 3-2 左側の電源コードを外します。また、右側のコードの ら外し、そのまま手前に引っ張ってペダルユニットを ナットを回して、コードを外します。 外します。 ELS-01Xの場合は、出力用コードの金属部分を引っぱっ て、出力用コードも外します。 ELS-01/01C ELS-01/01C ELS-01X ELS-01X 4 前面に回り、スピーカーユニットとキーボードユニッ トとをつないである、スピーカーコード、電源コード の2本を外します。 NOTE 鍵盤を持たないでください。故障の原因になることがあります。 ELS-01Xにはスピーカーユニットはありません。手順5へ進んでください。 3 リアプレートを外します。 3-1 上部右側の穴に六角レンチを差し込み、手前に引っ 張ってプレートを外します。 POWER 5 REAR SPEAKE OFF ON (フロッピーディスクドライブUD-FD01を接続して ある場合は)UD-FD01のUSBケーブルを外し、コー ドクランプにはさみます。 237ページの手順5をご覧くだ
7 6 キーボードユニットを取り外します。 6-1 キーボードユニットの下側にある、左右3本ずつの黒 スピーカーユニットを取り外します。 持ち手をつかんでスピーカーユニットを持ち上げ、左右 の位置決め突起から浮かせた状態で、スピーカーユニッ トを前方にスライドさせて外します。 ネジを、六角レンチ(小)を使って外します。 NOTE ELS-01Xにはスピーカーユニットはありません。手順8へ進んでください。 位置決め突起 6-2 図のように、キーボードユニットの背面の切り込み 取り外したスピーカーユニットは、必ず持ち手が上になるように 置いてください。 と、前面下部の波形ガイドに手をかけて、キーボード ユニットを真上に持ち上げ、外します。 スピーカーネットは、スピーカーに取り付けたままにしておいて ください。 ここを持つ ここを持つ 8 サイドフレームとリアフレームとを分解します。 8-1 背面が下になるように、フレームを倒します。 8-2 リアフレームの上下左右にある8本の黄ネジを、六角 レンチ(大)を使って外します。 ここを持つ ここを持つ ネジを外してから サイドフ
六角レンチの使い方 エレクトーンの分解や組み立てには、六角レンチを使用し ます。大小2種類の六角レンチが、エレクトーンの椅子の 座面裏に付属しています。 レンチの端を蹴ったり叩いたりして、衝撃を与えないでくだ さい。レンチが破損したり、お客様がけがをしたりする原因 になります。 ネジを締めるときには: 1 六角レンチの長い方か、または手で、ネジを時計 回りに軽く締めます。 六角レンチを使う場合 2 ある程度まで締めたら、六角レンチの短い方を ネジ穴に差し込み、長い方を持って時計回りに 回し、本締めします。 ネジがゆるまないよう、しっかりと締めてください。 ネジを外すときには、逆の手順で行ないます。 付 録 14 230 ELS-01/01C/01X 取扱説明書
エレクトーンの組み立て手順 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● エレクトーンを組み立てる前に、必ずお読みください。 ■ ご注意 部品をまちがえたり、向きをまちがえたりしないように注意して、手順どおりに組み立ててください。 組み立ては、必ず2人以上で行なってください。 組み立ては、必ず平らなところで行なってください。 ネジは付属の指定サイズ以外のものは使用しないでください。サイズの違うネジを使用すると、製品の破損や故障の原因になる ことがあります。 ネジは各ユニット固定後、ゆるみがないようきつく締め直してください。 本体の組み立てには、大小2種類の六角レンチ(対面6mmと4mm 、椅子の座面裏に付属)が必要です。六角レンチの使用方法については、230ペー ジをご覧ください。 1 すべての部品がそろっていることを確認します。 後 REAR OFF SPEAKER ON POWER キーボードユニット (約38kg) 前 スピーカーユニ
2 上下2つのリアフレームに左右のサイドフレームを取 り付けます。 3 スピーカーユニットを取り付けます。 NOTE 2-1 2つのリアフレームを、ネジ穴が見えるように置きま す。上下を間違えないようにしてください。 2-2 ELS-01Xにはスピーカーユニットはありません。手順4へ進んでください。 3-1 スピーカーユニットの持ち手をつかみ、2人でスピー リアフレームの端に、サイドフレームを上からはめ込 カーユニットを水平に持ったまま、楽器の前面から、 みます。 サイドフレーム上部のガイドレールに沿ってスライド させます。 サイドフレーム(左) フレーム前面にスピーカーユニットをぶつけないようにご注意く ださい。 スピーカーユニットを落とさないようにご注意ください。 リアフレーム(上) リアフレーム(下) 2-3 コードクランプ 黄ネジをネジ穴に差し込み、六角レンチ(大)を使って しっかり固定します。 3-2 ガイドレールの位置決め突起に、スピーカーユニット の穴を合わせます。 ここに合わせる 2-4 左右のサイドフレームが固定できたら、フレームを立 てます。
4 キーボードユニットを取り付けます。 4-1 図のように2人でキーボードユニットを持ち、スピー 4-4 背面に回り、左側の電源コードのプラグをキーボード ユニットのACインレットに差し込みます。右側のコ ネクターをつなぎ、ナットを回して固定します。 カーユニットの上に真上から下ろして、左右や背面に ELS-01Xの場合は、出力用コードも接続します。 突起を 隙間ができないようにはめます。 合わせて押し込みます。 ELS-01/01C 指や服をはさんだり、キーボードユニットを落としたりしないよ うご注意ください。 キーボードユニットとスピーカーユニットの間に電源コードなど をはさまないようご注意ください。 鍵盤に手をかけないでください。故障の原因になることがあります。 4-2 キーボードユニットの下側から、左右3本ずつの黒ネ ジを、六角レンチ(小)を使って固定します。 ELS-01X 5 リアプレートを取り付けます。 リアプレートの下をキーボードユニットの取り付け位置 に合わせてから、マジックテープで固定します。 4-3 前面のスピーカーコードと電源コードで、スピーカー ユニッ
6 ペダルユニットを取り付けます。 6-1 ペダルユニットの突起をサイドフレームの切り込みに 6-2 ペダルユニット左側のペダル鍵盤コードをつなぎ、 ナットを回して固定します。 あわせます。 ELS-01/01C 2 1 ELS-01X ELS-01Xの場合は、出力用コードも接続します。 突起を 合わせて押し込みます。 鍵盤を持たないでください。故障の原因になることがあります。 ペダルユニットとサイドフレームの間に、ペダル鍵盤コードをは さまないようご注意ください。 6-3 電源ケーブルをリアフレームのコードクランプにはさ みます。 付 録 14 234 ELS-01/01C/01X 取扱説明書
6-4 左右のサイドカバーを取り付けます。 ペダルユニットの突起と、サイドカバーの穴を合わせ、 ■ 必ず以下の点をチェックしてください。 サイドカバーを奥にスライドさせます。 ・エレクトーンの電源は入りますか? → 電源コードが確実に本体に差し込まれているかどうか 確認してください。(233ページ 4-4) ・エレクトーンの音は出ますか? → スピーカーコードやペダル鍵盤コードが確実に本体に 差し込まれているかどうか確認してください。(233 ページ 4-3、234ページ 6-2) → (ELS-01/01Cの場合)スピーカーユニットの電源が ONになっているかどうか確認してください。 使用中にエレクトーン本体や椅子がきしむ、 横ゆれする、 ぐらつくなどの症状がでたら、組み立て図に従って各部の ネジを締め直してください。 ■ 必ず以下の点をチェックしてください。 ・部品が余っていませんか? → 組み立て手順を再確認してください。 ・部屋のドアなどがエレクトーンにあたりませんか? → エレクトーンを適切な位置に移動してください。 ・エレクトーンがゆれませんか? → すべてのネジを確実に締め直して
椅子の組み立て手順 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 椅子の組み立てには、+(プラス)のドライバーが必要です。ご用意ください。 ELS-01の椅子の組み立て ELS-01C/01Xの椅子の組み立て 1 1 椅子座板を裏返しに置き、前側2本の椅子脚を取り付 けます。 椅子座板を裏返しに置き、六角レンチ(小)を使って左 右の椅子脚を取り付けます。 図のように、付属のスパナを使って、ボルトでしっかり 斜めになっている脚が前面に来るようにして、左右4本ず と固定します。 つのネジをしっかりと固定してください。 椅子座板とナットの間にワッシャーをはさみ、ボルトとワッシャー のすき間がなくなるまで締めつけてください。 椅子座板とナットの間にワッシャーをはさみ、 ネジとワッシャーの すき間がなくなるまで締めつけてください。 R ワッシャー ボルト R L L 文字のある方が うしろ 文字のある方が うしろ 2 +(プラス)
オプション品の取り付け フロッピーディスクドライブUD-FD01の取り付け ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● UD-FD01は、付属のケースと取り付けネジを使用して、エレ クトーンの鍵盤の下側に取り付けることができます。取り付け 2 USBケーブルを、ケースに収まるように折りたたみ 3 エレクトーンの鍵盤の右下に、取り付けネジでケース 4 USBケーブルをUSB TO DEVICE端子に挿します。 ます。 には+(プラス)のドライバーが必要です。ご用意ください。 1 を固定します。 ケースの3か所の両面テープから、はくり紙をはがし、 UD-FD01を、ケースに取り付けます。 両面テープ ELS-01C/01Xの場合はUSB TO DEVICE端子が2つあ るので、上の端子に挿してください。 5 コードクランプをOPTICAL OUT端子の左側に取り 付けます。 コードクランプは、エレクトーンの分解の際に使用しま
MIDIデータフォーマット 1. チャンネルメッセージ 1.
コード 受信 送信 オールサウンドオフ リセットオールコントローラ オールノートオフ オムニオフ オムニオン モノ ポリ 5-14ch × Cn, nn プログラムチェンジ 5-14ch 16ch × 16ch Dn, 00-7F アフタータッチ 1ch 2ch 3ch (4ch)* 5-14ch (1ch)* (2ch)* (3ch)* 上鍵盤 下鍵盤 ペダル鍵盤 リード1 XG En, 00-7F, 00-7F ピッチベンド 1ch 2ch (4ch)* 5-14ch (1ch)* (2ch)* × 上鍵盤 下鍵盤 リード1 XG 受信 送信 1-16ch × Bn, Bn, Bn, Bn, Bn, Bn, Bn, 78, 00 79, 00 7B, 00 7C, 00 7D, 00 7E, 00 7F, 00 ファンクション 備考 XG XG コントロール *MIDIコントロール(225ページ)で変更。 **4chに設定したときのみ出力される。 1.
コード Bn, 5B, 00-7F ファンクション リバーブセンドレベル 受信 送信 1-16ch × Bn, 5D, 00-7F コーラスセンドレベル 1-16ch × Bn, 5E, 00-7F バリエーションエフェクトセンドレベル 1-16ch × Bn, 60, 00-7F Bn, 61, 00-7F データインクリメント データデクリメント 1-16ch × Bn, 62, 00-7F Bn, 63, 00-7F NRPN LSB NRPN MSB 1-16ch × Bn, 64, 00-7F Bn, 65, 00-7F RPN LSB RPN MSB 1-16ch × Bn, Bn, Bn, Bn, Bn, Bn, Bn, オールサウンドオフ リセットオールコントローラ オールノートオフ オムニオフ オムニオン モノ ポリ 1-16ch × 78, 00 79, 00 7B, 00 7C, 00 7D, 00 7E, 00 7F, 00 Cn, 00-7F プログラムチェンジ 16ch 備考 コントロール 1-16ch Dn,
メッセージ 受信 送信 F0, 7F, 7F, 09, 03, 0n, CC, PP, VV, ..., F7 XN コード GM2コントロールチェンジパラメーター ○ × F0, 7F, 7F, 0A, 01, 0n, KK, CC, PP, VV, ..., F7 XN GM2キーベースドコントローラー ○ × ユニバーサルノンリアルタイムメッセージ 受信 送信 F0, 7E, 7F, 09, 01, F7 XN コード GM ON メッセージ ○ × F0, 7E, 7F, 09, 03, F7 XN GM2 ON ○ × F0, 7E, 7F, 09, 02, F7 XN GM OFF ○ × F0, 7E, 7F, 08, 08, JJ, GG, MM, ..data.., F7 XN GM2スケール/オクターブチューニング ○ × 受信 送信 XGネイティブ コード メッセージ F0, 43, 1N, 4C, AH, AM, AL, ..data..
*1. スイッチ 受信 送信 45H nn レフトフットスイッチ スイッチ ○ ○ 47H ニーレバー ○ ○ 48H フィルイン ○ × 4BH イントロ/エンディング ○ × 4DH ソロバー ○ ○ *2.
ブリリアンス cc スイッチ コード dd 備考 受信 受信値 送信 送信値 42 上鍵盤ボイス1ブリリアンス ○ [00-06] ○ [00-06] 00:BRILLIANT, 06:MELLOW 43 下鍵盤ボイス1ブリリアンス ○ [00-06] ○ [00-06] 00:BRILLIANT, 06:MELLOW 44 上鍵盤ボイス2ブリリアンス ○ [00-06] ○ [00-06] 00:BRILLIANT, 06:MELLOW 45 下鍵盤ボイス2ブリリアンス ○ [00-06] ○ [00-06] 00:BRILLIANT, 06:MELLOW 46 リードボイス1ブリリアンス ○ [00-06] ○ [00-06] 00:BRILLIANT, 06:MELLOW 47 ペダルボイス1ブリリアンス ○ [00-06] ○ [00-06] 00:BRILLIANT, 06:MELLOW 48 ペダルボイス2ブリリアンス ○ [00-06] ○ [00-06] 00:BRILLIANT,
*3.
Address Size Data データ 受信 受信値 送信 送信値 41 2 00007F7F エフェクト1パラメーター 1 MSB/LSB 0000-7F7F ○ 00007F7F ○ 00007F7F 00-07 42 2 00007F7F エフェクト1パラメーター 2 MSB/LSB 0000-7F7F 00007F7F 00007F7F 10 00-07 43 2 00007F7F エフェクト1パラメーター 3 MSB/LSB 0000-7F7F 00007F7F 00007F7F 10 00-07 44 2 00007F7F エフェクト1パラメーター 4 MSB/LSB 0000-7F7F 00007F7F 00007F7F 10 00-07 45 2 00007F7F エフェクト1パラメーター 5 MSB/LSB 0000-7F7F 00007F7F 00007F7F 10 00-07 46 2 00007F7F エフェクト1パラメーター 6 MSB/LSB 0000-7F7F
オルガンフルート音色パラメーター (Address mm: 0〜1 = 上鍵盤、下鍵盤) Address Size Data 受信 受信値 送信 送信値 00 1 00-7F フッテージ 16フィート 00:MIN 7F :MAX ○ 00-7F ○ 00-7F 00-01 01 1 00-7F フッテージ 8フィート 00:MIN 7F :MAX ○ 00-7F ○ 00-7F 11 00-01 02 1 00-7F フッテージ 5-1/3フィート 00:MIN 7F :MAX ○ 00-7F ○ 00-7F 11 00-01 03 1 00-7F フッテージ 4フィート 00:MIN 7F :MAX ○ 00-7F ○ 00-7F 11 00-01 04 1 00-7F フッテージ 2-2/3フィート 00:MIN 7F :MAX ○ 00-7F ○ 00-7F 11 00-01 05 1 00-7F フッテージ 2フィート 00:MIN 7F :MAX ○ 0
リズム リズムパラメーター Address Size Data 受信 受信値 送信 送信値 00-0B 2 00007F7F リズムアサインナンバー 0000-7F7F ○ 00-7F 00-7F ○ 00-7F 00-7F 00 10 1 00-0B 00 11 1 00-7F リズムセレクタナンバー 00-0B ○ 00-0B ○ 00-0B パーカッション ボリューム 00:MIN 7F :MAX ○ 00-7F × - 13 00 12 1 00-7F パーカッション リバーブ(センドレベル) 00:MIN 7F :MAX ○ 00-7F ○ 00-7F 13 00 13 1 00-7F セカンドエクスプレッション テンポコントロール(オン/オフ) 00:OFF 01:ON ○ 00-7F ○ 00-01 13 00 14 1 00-7F フットスイッチ 00:イントロ1 01:イントロ2 02:イントロ3 08:メインA 09:メインB 0A:メインC 0B:メインD
M.O.C.
Address Size Data 08 1 00-7F 00 09 1 00-7F 00 0A 3 00-04 00-04 (00-03)* 00-0B hh mm ll 14 00 14 14 パラメーター データ 受信 受信値 送信 送信値 MIDIコントロール エクスプレッション (インターナル/エクスターナル) 00: インターナル 01: エクスターナル ○ 00-7F × - MIDIコントロール リード1 (インターナル/エクスターナル) 00: インターナル 01: エクスターナル ○ 00-7F × - 00-04 00-04 (00-03) 00-0B ○ 00-04 00-04 (00-03) 00-0B ○ 00-04 00-04 (00-03) 00-0B 受信 受信値 送信 送信値 レジストレーションメニュー *ELS-01 全体エフェクトパラメーター : リバーブ Address Size Data 00 1 00-7F リバーブ デプス 00:MIN 7F :MA
MIDIインプリメンテーションチャート Date: 19-Sep-2003 Version: 1.
Date: 19-Sep-2003 Version: 1.
困ったときは 現象 原因と対処 楽器全般 電源を入れて10秒程度待たないと音が出ない。 時々ガリッとかポツンという雑音が入る。 システムの起動に時間がかかるためです。故障ではありません。 近くで電気器具の電源をオン/オフしたり、電気ドリルなどを使用している場合は、雑音 が入ることがあります。原因と思われる機器から、なるベく離れたコンセントを使ってく ださい。また、原因不明の場合は、サービスセンターまでご相談ください。 携帯電話や、ラジオ、テレビ、無線などの電波 が入る。 近くで携帯電話を使用していたり、近くに放送局やアマチュア無線局があるためです。 どうしても気になる場合は、サービスセンターまでご相談ください。 ラジオやテレビなどに雑音が入ることがある。 エレクトーンのすぐ近くにラジオやテレビを置くと、雑音が入ることがあります。できる かぎり離してご使用ください。 音が周囲のものを共鳴させてびりつく。 エレクトーンの音は持続音が多いため、周囲の戸棚やガラスなどの家具類を共鳴させる ことがあります。気になる場合は、家具類の配置を一工夫するか、エレクトーンの音量を 小さくしてください。 LCD
現象 原因と対処 ボイス/リズム 選んだボイスによって、鍵盤位置による音量の ばらつきがある。 一般に電子楽器は、音色を変えるという本質的な要素を持つため、音色による各鍵盤の音 量ばらつきをなくすことは非常に困難です。エレクトーンはどのボイスでも演奏上問題の ないように設計、調整されていますが、設置場所や聞く位置によって音量や音色が異なる ことがあります。どうしても気になる場合は、サービスセンターまでご相談ください。 ペダル鍵盤ではピッチが高く、上/下鍵盤の 高音部ではピッチが低く感じられる。 特にピアノと比較した場合に感じることです。ピアノでは倍音構成が複雑なため、高音と 低音の調律は実音での調律ができず、倍音を聞いて調律しています。エレクトーンの場合 は逆に実音で調律していますから、ピアノとエレクトーンでは、高音と低音の調律自体が 本質的に違うわけです。 割れるような感じや、ノイズが入るような感じ のするボイスがある。 おもに管楽器の音色で感じることです。これは実際の楽器音の特長を再現するため、意図 的に組み込まれた音色効果です。ブラスの振動やブレスノイズなど、よりリアルな特徴を そなえた音
現象 原因と対処 A.B.C./アカンパニメント/M.O.C. A.B.C.のシングルフィンガーで下鍵盤の高い方 を押さえても、音程が変わらない。 シングルフィンガーでは定められた1オクターブの中の音が出るようになっています。 同じコードまたは同じ音色であれば、下鍵盤のどの位置を押さえても同じ音程で和音が 得られます。 イントロ/エンディングパターンが鳴っている イントロ/エンディングパターンの演奏中はアカンパニメントコードが自動的に選択演奏 とき、下鍵盤を弾いても発音しない。 されるので、その他の音は発音しないようになっています。 アカンパニメントを選んでリズムをスタート ● アカンパニメントのボリュームが0に設定されています。リズムコンディション画面 させたが、アカンパニメントが鳴らない。 でアカンパニメントのボリュームを上げてください(65ページ)。 ● アカンパニメントのパートがすべてOFFになっています。ONに設定してください(64 ページ)。 メロディオンコード(M.O.C.
現象 原因と対処 MDR 録音/再生ができない。 ● パート選択ボタンがOFFになっていると、そのパートは録音/再生されません。画面上 で録音/再生したいパー卜のボタンを押してRECまたはPLAYにしてください。 ● 演奏データの容量が大きすぎます。 録音/再生できる演奏データの容量は1MBまでです。 ● メディアにライトプロテクトがかかっています。 ライトプロテクトのかかったメディア には録音できません。ライトプロテクトを外してください(96ページ)。 ● フォルダーにEL-900などのELシリーズのソングが入っていると、 そのフォルダーには 録音できません。 ELS-01/01C/01Xのソングを録音するフォルダーを作成してくだ さい。 演奏が終わる前に録音がストップしてしまった。 ● メディアの空き容量が不足しています。別のメディアを使用してください。 ● 既に録音してあるソングナンバーに録音する場合、録音する曲の長さは前に録音した 曲の長さになります。前に録音したソングを削除してから、録音しなおしてください (126ページ)。 ● 演奏データの容量が大きすぎます。容量が1MBを超える演奏は録
仕様 Electone STAGEA ELS-01 Electone STAGEA ELS-01C AWM (4) 音源 鍵盤 AWM (4) + VA + ORGAN 上鍵盤: 49鍵 (C〜C)、下鍵盤: 49鍵 (C〜C)、ペダル鍵盤: 20鍵 (C〜G) 鍵盤種 スタンダード鍵盤 (FS鍵盤) アフタータッチ 音色 カスタム鍵盤 (FSV鍵盤) 上鍵盤、下鍵盤 上鍵盤、下鍵盤、ペダル鍵盤 ホリゾンタルタッチ − 上鍵盤、下鍵盤 レジストレーション メニュー 240 300 レジストレーション メモリー M.(メモリー )、1〜16、D.
Electone STAGEA ELS-01 プログラム 機能 ボイスエディット ○ リズムパターン プログラム ○ リズムシーケンス プログラム フット スイッチ レフト プリセット1、2、ユーザー 1、2、3、4、5、6、7、8 (パン、ピッチコース、ピッチファイン、リバーブ、ボリューム) [リズム] 停止、ブレイク、メインA、B、C、D、イントロ1、2、3、エンディング1、2、3、 [グライド] 上鍵盤1、2、リード1、2、下鍵盤1、2、タイム設定 [ロータリースピーカー ] ライト レジストレーションシフト ○ エクスプレッション ペダル セカンドエクスプ レッションペダル ピッチベンド、テンポ (設定/再生 のみ) トランスポーズ -6〜+6 A=427.2〜452.
エレクトーン用語辞典 ここでは、エレクトーンに特有の機能や、パネル上または画面上に出てくる難しい用語について掲載します。 電子楽器全般に関する基本的な用語、ボイスエディットやエフェクトに関する各パラメーターの意味などは、 インターネット上の下記ページにも掲載してありますので、参考にしてください。 ■ ヤマハ電子楽器用語集 ■ エレクトーン用語検索
用語 解説 ページ 音群ごとに、ボイスのピッチを変更する機能。各音群のチューンをずらしておくことで、 演奏に厚みを持たせることができる。 45 チ チューン テ ディスプレイセレクト LCDディスプレイの右側にある12個のボタン群。 12 データコントロールダイアル 画面に表示される数値やスライダーなどを操作するためのダイアル。 16 トゥーロワー リードボイスやペダルボイスを、下鍵盤で演奏できる機能。 トランスポーズ 移調の設定。音群ごとでも楽器全体でも変更できる。 ニ ニーレバー 膝で操作するレバー。サステインやメロディオンコードなどをコントロールできる。 ネ ネクストレジスト 1つのソング内に複数のレジストレーションデータを保存した場合に、レジストレーショ ンシーケンスまたはフットスイッチ操作でそれらを次々に読み込む機能。 90、181 ハ パート再生/録音 MDR機能で演奏データを録音する場合に、鍵盤ごとに録音や再生を行なうこと。リード ボイスだけ、キーボードパーカッションだけを別に録音することもできる。 105、117 ト 28 45、19
用語 リ レ ロ 260 ページ リズムの発音状態(=コンディション)を設定する画面の名称。リズムボタンを2度押すと 表示される。 リズムシーケンスプログラム リズムパターンを1小節ずつ並べて、1曲分のリズムデータをプログラムする機能。 175 リズムパターンプログラム 打楽器音を入力することで、リズムパターンを作成する機能。内蔵されているリズムを 編集してオリジナルのパターンをつくることもできる。 145 リズムメニュー リズムボタンを押したときに表示される画面。 リードボイス 上鍵盤で演奏できるリードパート用の音群。単音で発音する。 24 リバーブ 音に残響をつけ、広いホールなどで演奏しているような響きを与えるエフェクト。 46 レジストレーション 上鍵盤、下鍵盤、ペダル鍵盤のボイスや、エフェクト、リズム、アカンパニメントなどの 設定情報のこと。 83 レジストレーションシーケンス リズムと同期して自動的にレジストレーションを切り替える機能。どのタイミングで レジストレーションを切り替えるかは、あらかじめ設定しておく。 レジストレーションシフト フットス
索引 A M A.B.C./M.O.C. ............................................................ 65, 67 [M.](メモリー ) .................................................................. 83 AUX IN ........................................................................... 212 M.O.C. ............................................................................... 67 AUX OUT ....................................................................... 212 MAIN/FILL IN ............................................................
V ア VA (ボイスエディット) .................................................... 140 アーリー /カラオケ ............................................................ 53 VA音源 .............................................................................. 36 アカンパニメント ............................................................... 64 VAカスタムボイス ........................................................... 142 アクセント ....................................................................... 152 VOICE DISPLAY .....................
ケ ソ ゲートタイム ................................................................... 161 送信チャンネル(MIDI) ...................................................... 225 言語/LANGUAGE ............................................................ 17 ソロ ................................................................................... 29 ソング ........................................................................ 99, 103 コ ソングコピー ................................................................... 123 コード1 ...........
ノ ヘ ノートシフト ................................................................... 137 ペダルボイス ..................................................................... 25 ノートリミット ................................................................ 137 ペダルポリモード ............................................................... 43 ヘッドフォン ................................................................... 213 ハ バー /ビート ...................................................................... 59 ホ バージョン .................
ラ ラスト(リードボイス) ......................................................... 43 リ リアルタイム入力 .................................................... 150, 158 リードスライド .................................................................. 45 リード分離 ....................................................................... 105 リードボイス ..................................................................... 24 リズム ............................................................................... 54 リズムクロック(リズムパターンプログラム) ..............
メモ ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 266 ELS-01/01C/01X 取扱説明書
保証とアフターサービス ■ ヤマハ電気音響製品サービス拠点 (修理受付および修理品お持込み窓口) サービスのご依頼、お問い合わせは、お買い上げ店、またはお近 くのヤマハ電気音響製品サービス拠点にご連絡ください。 ◆ 修理のご依頼 / 修理についてのご相談窓口 ヤマハ電気音響製品修理受付センター ● 保証書 受付時間 本機には保証書がついています。 保証書は販売店がお渡ししますので、必ず「販売店印・お買い上 げ日」などの記入をお確かめのうえ、大切に保管してください。 月曜日〜金曜日 9:00〜19:00、土曜日 9:00〜 17:30 (祝祭日および弊社休業日を除く) 0570-012-808 ナビダイヤル (全国共通番号) ※一般電話・公衆電話からは、市内通話料金でご利用いただけます。 FAX (053) 463-1127 ● 保証期間 お買い上げ日から1年間です。 ◆ 修理品お持込み窓口 受付時間 ● 保証期間中の修理 保証書記載内容に基づいて修理いたします。詳しくは保証書を 月曜日〜金曜日 9:00〜17:45 (祝祭日および弊社休業日を除く) * お電話は、電気音響製品
国内楽器営業本部 鍵盤統括部 企画推進室 〒108-8568 東京都港区高輪2-17-11 TEL 03(5488)5443 PA•DMI事業部 EKBマーケティング部 ELグループ 〒430-8650 浜松市中沢町10-1 TEL 053(460)2191 エレクトーンに関するご質問にお答えいたします。 エレクトーンインフォメーションセンター 営業日時: 月〜土 10:30〜19:00 フリーダイヤル 0120–186–808 (携帯電話からおかけになる場合は053-460-4836) サポート:http://www.yamaha.co.jp/support/ インターネットホームページ ヤマハ株式会社ホームページ http://www.yamaha.co.jp/ ヤマハエレクトーン総合情報サイト Electone Station http://electone.jp/ ヤマハマニュアルライブラリー http://www.yamaha.co.jp/manual/japan/ あなたの音楽生活をフルサポート ミュージックイークラブ http://www.music-eclub.