Owner’s Manual Keep This Manual For Future Reference.
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
Precautions 3 Precautions WARNING Installation • Connect this unit’s power cord only to an AC outlet of the type stated in this Owner’s Manual or as marked on the unit. Failure to do so is a fire and electrical shock hazard. • Do not allow water to enter this unit or allow the unit to become wet. Fire or electrical shock may result. • Do not place a container with liquid or small metal objects on top of this unit. Liquid or metal objects inside this unit are a fire and electrical shock hazard.
Precautions EMX62M—Owner’s Manual
Contents 5 Introduction Thank you for purchasing the Yamaha EMX62M Powered Mixer. In order to take full advantage of the EMX62M and enjoy long and trouble-free operation, read this owner’s manual carefully, and keep it in a safe place for future reference. Features • The EMX62M’s six input channels support a wide range of audio sources, including microphones, instruments, and line-level devices.
EMX62M Quick Guide EMX62M Quick Guide The following steps (1-5) explain the basic connection and operation of the EMX62M. Also, please read “Front and Rear Panel” and “Basic Operation” following this Quick Guide section to learn more about using the EMX62M. Connecting a microphone Make sure that the power is turned off to the EMX62M. Connect a microphone to the Low-Z jack of channel 1-4.
EMX62M Quick Guide • To connect a second player, use the LINE jack or HiZ jack. • You cannot use the Hi-Z jack and the Low-Z jack for the same channel at the same time. If a microphone has already been connected to the Low-Z jack of a channel, you cannot connect a player to the Hi-Z jack of the channel. • Connect a recorder to the REC OUT jacks. Connecting an electric acoustic guitar or electric bass Connect an electric acoustic guitar or electric bass to the Super Hi-Z jacks.
EMX62M Quick Guide STEP 2 Power on STEP 4 Applying built-in effects 1 Turn on the power to all external devices connected to the EMX62M. 2 Make sure that the MASTER controls in the MONITOR section and the MAIN section are set to “0,” then press the POWER switch on the EMX62M to turn on the power. 1 Turn on the ON switch in the DIGITAL EFFECT section. The ON switch indicator lights up. 2 Select one of three effect types, then press the switch.
Front & Rear Panels 9 Front & Rear Panels Control Panel ■ Channel Section The channel controls are used to set the EQ, MONITOR and EFFECT send levels, channel LEVEL, and PAD for each channel. The MONITOR control is not affected by the channel’s LEVEL control 4, since the MONITOR signal is sourced before that control.
Front & Rear Panels ■ DIGITAL EFFECT Section The DIGITAL EFFECT section is used to turn the built-in digital effects processor on and off and select effects programs. ■ MAIN Section The MAIN section is used to set the MAIN MASTER level, 7-band graphic equalizer, AUX IN and 2TR IN levels, and MAIN EFFECT RTN level. It also contains the LIMITER indicator and main output level meter.
Front & Rear Panels 11 ■ PHANTOM switch and indicator M Peak level indicator This indicator indicates the level of the signal output from the MAIN OUTPUT jack (input/ output panel 9). Adjust the MASTER control B so that this indicator lights up only momentarily to avoid distortion. G N LIMITER indicator The LIMITER indicator lights up when the limiter circuit, which is designed to protect the internal power amplifier against excessive input signals and load mismatches, activates.
Front & Rear Panels Input/Output Panel 4 2 1 3 1 Hi-Z, Low-Z (inputs 1–4) Hi-Z (TRS phone jack) Pin 1: ground Sleeve: ground Pin 2: hot (+) Ring: cold (–) Pin 3: cold (–) Tip: hot (+) S + - GND R T GND - + Note: The Low-Z and Hi-Z input of each channel cannot be used simultaneously. Use the input appropriate for the source.
Front & Rear Panels 13 I MAIN—OUTPUT jack The MAIN—OUTPUT phone jack outputs the MAIN bus signal after the 7-band graphic equalizer and MASTER level control, and can be connected to the input of a larger mixer, or a more powerful amplifier, for example. J MONITOR—OUTPUT The MONITOR—OUTPUT phone jack outputs the MONITOR bus signal after the MONITOR MASTER control, and can be connected to the input of a powered monitor speaker.
Front & Rear Panels Rear Panel 2 1 1 SPEAKERS 1 & 2 jacks The SPEAKER 1 & 2 phone jacks output the main signal from the internal power amplifier and are used to connect speakers. They are internally connected in parallel and output the same signal. Connecting one speaker Installation The EMX62M uses a forced cooling system with intake on the bottom of the rear panel and exhaust on the top of the rear panel to avoid blocking the heated air flow.
Front & Rear Panels 15 Hookup Example Recorder (Cassette, DAT, MD) CD player Effects processor 88 Synthesizer, Drum machine, Guitar processor Powered monitor VOL *2 Headphones *1 Footswitch (YAMAHA FC5) Microphone Larger mixer or Amplifier Electric-acoustic guitar * The Low-Z and Hi-Z input of each channel cannot be used simultaneously. Electric bass *1.
Basic Operation Basic Operation Connecting Sources Before connecting any microphones or instruments, make sure that the EMX62M and any other applicable equipment is turned off. Also make sure that the LEVEL control on each EMX62M input channel, and the MAIN MASTER and MONITOR MASTER controls are turned down. 1 Connect cables to your mics and instru- input channel MONITOR controls are not affected by the LEVEL controls. 1 Set the MONITOR MASTER control to the √” position.
Installing an optional rack mount kit 17 Installing an optional rack mount kit You can rack-mount the EMX62M using an optional rack mount kit (RK-88). Rack mount kit RK-88 Installing the rack mount bracket 1 Remove the carrying handle by loosening and removing four screws. • Bracket × 2 • Screw × 6 Before you rack-mount the EMX62M, make sure that sufficient ventilation will be maintained. (Never install the unit in a sealed rack.
Troubleshooting Troubleshooting The following table describes the possible malfunctions of this demvice, and the appropriate actions to be taken in each case. Problem The POWER indicator is lit. Sound is no longer output from the speakers. Cause Action The load on the amplifier of this device was too great, and the protection circuit for the amplifier has operated.
Specifications 19 Specifications ■ General Specifications Maximum output power 135 W/8Ω @0.5% THD at 1 kHz (SPEAKERS OUT) 200 W/4Ω @0.5% THD at 1 kHz (SPEAKERS OUT) 175 mW/40Ω @0.5% THD at 1 kHz (PHONES OUT) Frequency response 20 Hz–20 kHz +1 dB, –3 dB @1 W output into 8Ω (SPEAKERS OUT) 20 Hz–20 kHz +1 dB, –3 dB @+4 dB output into 10 kΩ (MAIN OUT, MONITOR OUT, EFFECT OUT) Total harmonic distortion Less than 0.5% @20 Hz–20 kHz, 100 W output into 4Ω (SPEAKERS OUT) Less than 0.
Specifications ■ Input Specifications Input connectors PAD CH INPUT (Lo-Z) (CH1–4) OFF CH INPUT (Hi-Z) (CH1–4) OFF ON ON Actual load impedance 3 kΩ 10 kΩ Input level Nominal impedance Sensitivity*1 50–600Ω Mics 600Ω Lines Connector type Nominal level Max. before cliping –62 dB (0.616 mV) –50 dB (2.45 mV) –20 dB (77.5 mV) –32 dB (19.5 mV) –20 dB (77.5 mV) +10 dB (2.45 V) 50–600Ω Mics –52 dB (1.95 mV) –40 dB (7.75 mV) –10 dB (245 mV) 600Ω Lines –22 dB (61.
CH6 IN CH5 IN –50dB –40dB –30dB –20dB –10dB 0dB +10dB +20dB +30dB SUPER Hi-Z [–30dB] LINE [–10dB] Hi-Z [–40/–10] 2 1 2 1 Low-Z, MIC [–50dB] Hi-Z [–40dB] SUPER Hi-Z [–30dB] Low-Z [–20dB] Hi-Z [–10dB] HA HA ON OFF [–10dB] FOOT SW (MITE) [–10dB] 2-Stage EQ 2-Stage EQ 2-Stage EQ Clip Level [+20dB] BA BA AUX IN [–10dB] 2TR IN [–10dBV] SMALL HALL LARGE HALL VOCAL REVERB 2 1 AUX IN [–10dB] PAD 2TR IN [–10dBV] [–7.
YAMAHA CORPORATION V833080 R0 1 AP 24 NP Printed in Taiwan Pro Audio & Digital Musical Instrument Division P.O.