User Manual

2 green Euroblock Connectors
2 black Euroblock Connectors
2 Ferrites
Elite – 2 Quick Guide
1. Power In (100-240 VAC, 50/60 Hz)
2. Remote Antenna Connector, PoE enabled
3. Not used
4. LAN network connector
5. Serial port for room control interface
6. Not used
7. Not used
8. Euroblock Connectors microphone channels 1-2, analog audio in (black)
and audio out (green). Connectors for channel 3 and 4 are not acve.
Installing the Base DSP Unit
Remove the Execuve Elite Base DSP unit from the packaging. To install
the Execuve Elite Base in an AV rack, locate the rack ears on each side.
Use screws (not provided) to secure the Elite base in the rack.
Content
1 Base DSP Unit
1 Antenna
1 Antenna Back-plate
1 Charging Base
1 Power Supply
1 Power cord
1 Cat 5 Cable
1 USB Cable
Plug the power cord into the back of the Elite Base (1); If adding the Elite
system to a network, connect the LAN cable (4).
Analog Audio is processed through Euroblock inputs and outputs, separated
by channel, 1 - 2 (8). See documentaon on the polarity of the connectors.
Control systems may use the serial connector (5) on the back of the Base
unit, or connect through the network.
Installing the Antenna
Locate the Antenna back-plate and the Antenna.
Mount the back plate using the correct
holes for your installaon type.
For a wall installaon, the snap
should be at the boom. When
installing the Antenna on the ceiling,
whether using a Revolabs Ceiling kit or other installaon methods, please ensure that you
add addional safety wires in case the snaps fail, to prevent injury from a falling Antenna.
The Elite Antenna is aached to the Base with a Cat 5 or Cat 6 cable.
Install one of the ferrites on the antenna network cable going into the base,
approximately 1/4 inch (6 mm) from the connector. On the Base side, plug the cable into
the Antenna connector (2). The connecon between the Base DSP Unit and the Antenna
is me crical and needs to be a direct connecon, not routed through a switch.
If the antenna wire is meant to be routed
through the network cable opening in the
back-plate, route the cable through that opening before aaching the second ferrite.
Otherwise, aach the ferrite to the cable first, then put it through one of the roung
channels. Either way, the ferrite should be placed 5 inches (12.5 cm)
from the end of the cable. Aach the cable to the antenna,
placing the ferrite in the storage opening in the antenna.
Make sure that the cable is plugged in securely before
connuing.
Finally, aach the antenna to the back plate by hooking the top
of the antenna over the two hooks at the top of the back plate.
Then push the boom into the back plate unl the snap clicks in.
To remove the antenna from the back-plate later, first find the slit
along the boom. Insert a screwdriver into the slit
and press the snap inside so the Antenna can be swung off.
Installing the Charger Base
Remove the Charger Base from the box, along
with the 24 volt power supply.
Plug the power connector into the back of the
charger tray, and connect it to the power mains.
The Charger Base is ready for use.
Place Execuve Elites microphones into the tray with the charging contacts of the micro-
phone matching the charging contacts of the Charger. A magnet will pull the microphones
in, and maintain contact for charging.
Network
cable
opening
For full documentaon please visit
hp://www.uc.yamaha.com/Elite-2
1
2
3
4
5
6
7
8
MN-ELITE-2-QSG-20180511-EN © Yamaha Unified Communicaons, Inc.