Revolabs Executive Elite™ Wireless Microphone System Room Control API Guide Models: 01-ELITEEXEC8 01-ELITEEXEC4 03-ELITEEXEC8-EU 03-ELITEEXEC4-EU 03-ELITEEXEC8-TW 03-ELITEEXEC4-TW 03-ELITEEXEC8-JP 03-ELITEEXEC4-JP
© YAMAHA UNIFIED COMMUNICATIONS INC. All rights reserved. No part of this document may be reproduced in any form or by any means without express written permission from Yamaha Unified Communications, Inc. Product specifications are subject to change without notice.
Contents Using an Executive Elite with a Control System .......................................................................... 4 Serial Command & Return Strings ............................................................................................... 5 Channel Number: .................................................................................................................................. 6 Examples: ..........................................................................................
Using an Executive Elite with a Control System The Executive Elite Base DSP can be monitored and controlled via an external control system. Communication can either be over the serial port of the Executive Elite, or over an IP connection. If several Executive Elite Base DSPs are part of an installation, each requires its own connection to the control system in order to communicate.
connection. Client mode in the executive Elite is persistent, meaning that if the server goes down or the connection is lost for any reason, the Executive Elite will periodically ping the server until the connection is re-established, without requiring a reboot. If the Executive Elite is the server, only one device can login at a time. The login username is revolabs and the password is elite, both case sensitive. The port number is the standard Telnet port 23.
Channel Number: The options for the portion of the serial strings are 1-8 for an Executive Elite 8, and 1-4 for an Executive Elite 4 system, since each Base station can only control up to 8 or 4 microphones, respectively. The corresponds to the channel number the microphone is paired to in the Executive Elite. A of “A” will control all microphones.
Command String Tables: Property/Action Command Format Description Response addmictogroup Add the given mic into the designated group. antennafwversion addmictogroup ch get antennafwversion antennalinkstatus get antennalinkstatus antennamacaddr get antennamacaddr Retrieve the antenna link status, 0 - link down, 1 - link is up. Retrieve antenna's MAC address.
Property/Action Command Format Description Response 23 - Costa Rica, 24 - Venezuela, 25 - Middle East create mutegroup create mutegroup get currentipaddress Create a new mute group. currentipdefaultgatew ay currentipdns get currentipdefaultgateway Retrieve current default gateway address. get currentipdns Retrieve current IP DNS address. currentipsubnet get currentipsubnet Retrieve current IP subnet. delete mutegroup Delete an existing group.
Property/Action Command Format Description Response logmask set logmask <0/1/2/3> Configure the debug log level, minimum severity, 0 - debug, 1 - warning, 2 - error, 3 - off. val logmask <0/1/2/3> lopassfilter set lopassfilter ch <0/12000/8000/4000> get lopassfilter ch Configure the low pass filter value for a given channel. macaddr get macaddr Retrieve system's MAC address.
Property/Action Command Format Description Response pushtotalk get pushtotalk pushtotalk set pushtotalk <0/1/2> get pushtotalkmic ch regnotify Retrieve group push to talk setting value, 1 - push to talk set, 0 - not set. Configure group push to talk setting, 1 - push to talk set, 0 - not set, 2 - toggle. Retrieve microphone's push to talk state. 1 - push to talk set, 0 - not set.
The command ‘regnotify’ listed above will turn on notifications. The following table lists the notifications sent by the system. Notifications Notification Format Description mute_group_change notify mute_group_change Notify client that changes that affect a given group have occurred. Actions include 'add' - add, 'del' delete, 'ren' - rename.
Notifications Notification Format Description status_change_antenna_link notify status_change_antenna_link status_change_battery notify status_change_battery ch Notify client antenna link status changed, 0 - unlinked, 1 - linked. Notify client the given microphone's battery status changes.
Legacy Notifications Notification Format Description batt val batt gain val gain… lock val lock… Mic battery status. 1 - 25%, 2 - 50%, 3 - 75%, 4 - 100% Reports gain value 80 - 100 = gain values -20db - 0db, in 1db increments. (ex: 81 = -19db) 101 – 120 = gain value 0db Mic lock status.