OWNER’S MANUAL FZS1000R FZS1000RC FZS1000SR FZS1000SRC YAMAHA MOTOR CO., LTD. PRINTED ON RECYCLED PAPER PRINTED IN JAPAN 2002.06-1.
EAU03438
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM EAU00002 INTRODUCTION Congratulations on your purchase of the Yamaha FZS1000/FZS1000S. This model is the result of Yamaha’s vast experience in the production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields. This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle.
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM IMPORTANT MANUAL INFORMATION Particularly important information is distinguished in this manual by the following notations: The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Failure to follow WARNING instructions could result in severe injury or death to the motorcycle operator, a bystander or a person inspecting or repairing the motorcycle.
U5LV12.book Page 2 Thursday, June 27, 2002 5:49 PM IMPORTANT MANUAL INFORMATION EW000000 WARNING PLEASE READ THIS MANUAL AND THE “YOU AND YOUR MOTORCYCLE: RIDING TIPS” BOOKLET CAREFULLY AND COMPLETELY BEFORE OPERATING THIS MOTORCYCLE. DO NOT ATTEMPT TO OPERATE THIS MOTORCYCLE UNTIL YOU HAVE ATTAINED ADEQUATE KNOWLEDGE OF ITS CONTROLS AND OPERATING FEATURES AND UNTIL YOU HAVE BEEN TRAINED IN SAFE AND PROPER RIDING TECHNIQUES.
U5LV12.book Page 3 Thursday, June 27, 2002 5:49 PM IMPORTANT MANUAL INFORMATION AFFIX DEALER LABEL HERE EAU04247 FZS1000R/FZS1000RC/FZS1000SR/FZS1000SRC OWNER’S MANUAL ©2002 by Yamaha Motor Corporation, U.S.A. 1st edition, May 2002 All rights reserved. Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A. is expressly prohibited. Printed in Japan.
U5LV12.
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM SAFETY INFORMATION Safe riding .......................................................................................... 1-1 Protective apparel .............................................................................. 1-3 Modifications ...................................................................................... 1-3 Loading and accessories ................................................................... 1-3 Gasoline and exhaust gas.......
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM SAFETY INFORMATION EAU00014 1- 1 2 3 4 5 6 7 8 9 MOTORCYCLES ARE SINGLE TRACK VEHICLES. THEIR SAFE USE AND OPERATION ARE DEPENDENT UPON THE USE OF PROPER RIDING TECHNIQUES AS WELL AS THE EXPERTISE OF THE OPERATOR. EVERY OPERATOR SHOULD KNOW THE FOLLOWING REQUIREMENTS BEFORE RIDING THIS MOTORCYCLE. HE OR SHE SHOULD: 1. OBTAIN THOROUGH INSTRUCTIONS FROM A COMPETENT SOURCE ON ALL ASPECTS OF MOTORCYCLE OPERATION. 2.
U5LV12.book Page 2 Thursday, June 27, 2002 5:49 PM SAFETY INFORMATION 4. Many accidents involve inexperienced operators. In fact, many operators who have been involved in accidents do not even have a current motorcycle license. a. Make sure that you are qualified and that you only lend your motorcycle to other qualified operators. b. Know your skills and limits. Staying within your limits may help you to avoid an accident. c.
U5LV12.book Page 3 Thursday, June 27, 2002 5:49 PM SAFETY INFORMATION Protective apparel 1 2 3 4 5 The majority of fatalities from motorcycle accidents are the result of head injuries. The use of a safety helmet is the single most critical factor in the prevention or reduction of head injuries. 1. Always wear an approved helmet. 2. Wear a face shield or goggles. Wind in your unprotected eyes could contribute to an impairment of vision that could delay seeing a hazard. 3.
U5LV12.book Page 4 Thursday, June 27, 2002 5:49 PM SAFETY INFORMATION Loading The total weight of the operator, passenger, accessories and cargo must not exceed the maximum load limit of FZS1000, FZS1000S: 189 kg (417 lb) / FZS1000C, FZS1000SC: 188 kg (415 lb). When loading within this weight limit, keep the following in mind: 1. Cargo and accessory weight should be kept as low and close to the motorcycle as possible.
U5LV12.book Page 5 Thursday, June 27, 2002 5:49 PM SAFETY INFORMATION 1 2 3 4 5 6 7 8 9 a. Accessories fitted to the handlebar or the front fork area can create instability due to improper weight distribution or aerodynamic changes. If accessories are added to the handlebar or front fork area, they must be as lightweight as possible and should be kept to a minimum. b. Bulky or large accessories may seriously affect the stability of the motorcycle due to aerodynamic effects.
U5LV12.book Page 6 Thursday, June 27, 2002 5:49 PM SAFETY INFORMATION a. The engine and exhaust system may be hot, therefore, park the motorcycle in a place where pedestrians or children are not likely to touch these hot areas. b. Do not park the motorcycle on a slope or soft ground, otherwise it may fall over. c. Do not park the motorcycle near a flammable source (e.g., a kerosene heater, or near an open flame), otherwise it could catch fire. 4.
U5LV12.book Page 7 Thursday, June 27, 2002 5:49 PM SAFETY INFORMATION EAU02977 Location of important labels Please read the following important labels carefully before operating this motorcycle.
U5LV12.book Page 8 Thursday, June 27, 2002 5:49 PM SAFETY INFORMATION 1 5 California only CAUTION Cleaning with alkaline or acid cleaner, gasoline or solvent will damage windshield. Use neutral detergent.
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM DESCRIPTION Left view ............................................................................................. 2-1 Right view........................................................................................... 2-2 Controls and instruments ...................................................................
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM DESCRIPTION EAU00026 2- Left view 2 1. Front fork compression damping force adjusting screw 2. Front fork rebound damping force adjusting screw 3. Front fork spring preload adjusting bolt 4. Air filter element 5. Fuses 6. Storage compartment 7. Grab bar 8. Seat lock/helmet holder 9. Shock absorber assembly compression damping force adjusting screw 10. Shock absorber assembly spring preload adjusting ring 11.
U5LV12.book Page 2 Thursday, June 27, 2002 5:49 PM DESCRIPTION Right view 2 13. Owner’s tool kit 14. Rear brake fluid reservoir 15. Battery 16. Front brake fluid reservoir 17. Radiator cap 18. Engine oil filter cartridge 19. Engine oil level check window 20. Brake pedal 21.
U5LV12.book Page 3 Thursday, June 27, 2002 5:49 PM DESCRIPTION Controls and instruments 2 1. Clutch lever 2. Left handlebar switches 3. Starter (choke) lever 4. Speedometer unit 5. Main switch/steering lock 6. Tachometer unit 7. Fuel gauge 8. Right handlebar switches 9. Brake lever 10.
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS Main switch/steering lock .................................................................. 3-1 Indicator and warning lights ............................................................. 3-2 Speedometer unit .............................................................................. 3-3 Tachometer unit ................................................................................. 3-4 Self-diagnosis devices ..........
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS EAU00027 3- 3 EAU00029 Main switch/steering lock The main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below. EAU00032 ON All electrical systems are supplied with power, and the headlight, meter lighting, taillight and position lights come on, and the engine can be started. The key cannot be removed.
U5LV12.book Page 2 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS EAU00063 EAU04881 High beam indicator light “ ” This indicator light comes on when the high beam of the headlight is switched on. Coolant temperature warning light “ ” This warning light comes on when the engine overheats. When this occurs, stop the engine immediately and allow the engine to cool. The electrical circuit of the warning light can be checked by turning the key to “ON”.
U5LV12.book Page 3 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS This information will enable you to plan future fuel stops. To set a mode Push the “SELECT” button to change between the odometer mode “ODO”, and the tripmeter modes “TRIP 1” and “TRIP 2” in the following order: ODO → TRIP 1 → TRIP 2 → ODO 3 1. 2. 3. 4. 5. 6. 7.
U5LV12.book Page 4 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS 1. Tachometer 2. Tachometer red zone 3. Clock EAU03954 Tachometer unit The electric tachometer allows the rider to monitor the engine speed and keep it within the ideal power range. EC000003 CAUTION: Do not operate the engine in the tachometer red zone. Red zone: 11,500 r/min and above _ To set the clock: 1. Push both the “SELECT” and “RESET” buttons for at least two seconds. 2.
U5LV12.
U5LV12.book Page 6 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS EAU03889 Turn signal switch “ / ” To signal a right-hand turn, push this switch to “ ”. To signal a left-hand turn, push this switch to “ ”. When released, the switch returns to the center position. To cancel the turn signal lights, push the switch in after it has returned to the center position. 1. Dimmer switch “ / 2. Turn signal switch “ 3.
U5LV12.book Page 7 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS 3 1. Clutch lever 1. Shift pedal EAU00152 EAU00157 Clutch lever Shift pedal The clutch lever is located at the left handlebar grip. To disengage the clutch, pull the lever toward the handlebar grip. To engage the clutch, release the lever. The lever should be pulled rapidly and released slowly for smooth clutch operation.
U5LV12.book Page 8 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS 2. Turn the key counterclockwise to the original position, remove it, and then close the lock cover. NOTE: The fuel tank cap cannot be closed unless the key is in the lock. In addition, the key cannot be removed if the cap is not properly closed and locked. _ 1. Brake pedal EAU00162 Brake pedal The brake pedal is on the right side of the motorcycle. To apply the rear brake, press down on the brake pedal. _ 1.
U5LV12.book Page 9 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS EAU00185 EAU04265 CAUTION: Immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteriorate painted surfaces or plastic parts. Recommended fuel: UNLEADED GASOLINE ONLY Fuel tank capacity: Total amount: 21 L (4.6 Imp gal, 5.5 US gal) Reserve amount: 4 L (0.9 Imp gal, 1.1 US gal) _ _ 3 1. Fuel tank filler tube 2. Fuel level ECA00104 CAUTION: Use only unleaded gasoline.
U5LV12.book Page 10 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS Your Yamaha engine has been designed to use regular unleaded gasoline with a pump octane number [(R+M)/2] of 86 or higher, or a research octane number of 91 or higher. If knocking (or pinging) occurs, use a gasoline of a different brand or premium unleaded fuel. Use of unleaded fuel will extend spark plug life and reduce maintenance costs. 3 1.
U5LV12.book Page 11 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS 3 1. Seat lock 2. Unlock. 1. Projection 2. Seat holder EAU03956 Seat To remove the seat 1. Insert the key into the seat lock, and then turn it clockwise. 2. While holding the key in that position, lift the rear of the seat, and then pull the seat off. 1. Helmet holder 2. Unlock. To install the seat 1. Insert the projection on the front of the seat into the seat holder as shown. 2.
U5LV12.book Page 12 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS When storing the owner’s manual or other documents in the storage compartment, be sure to wrap them in a plastic bag so that they will not get wet. When washing the motorcycle, be careful not to let any water enter the storage compartment.
U5LV12.book Page 13 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS 3 1. Spring preload adjusting bolt Spring preload To increase the spring preload and thereby harden the suspension, turn the adjusting bolt on each fork leg in direction a. To decrease the spring preload and thereby soften the suspension, turn the adjusting bolt on each fork leg in direction b. 1. Current setting 2. Front fork cap bolt 1.
U5LV12.book Page 14 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS EC000015 CAUTION: Never attempt to turn an adjusting mechanism beyond the maximum or minimum settings. _ _ NOTE: Although the total number of clicks of a damping force adjusting mechanism may not exactly match the above specifications due to small differences in production, the actual number of clicks always represents the entire adjusting range.
U5LV12.book Page 15 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS NOTE: ● Align the appropriate notch in the adjusting ring with the position indicator on the shock absorber. ● Use the special wrench included in the owner’s tool kit to make the adjustment. _ 3 1. Spring preload adjusting ring 2. Special wrench 3. Position indicator Spring preload To increase the spring preload and thereby harden the suspension, turn the adjusting ring in direction a.
U5LV12.book Page 16 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS NOTE: Although the total number of clicks of a damping force adjusting mechanism may not exactly match the above specifications due to small differences in production, the actual number of clicks always represents the entire adjusting range. To obtain a precise adjustment, it would be advisable to check the number of clicks of each damping force adjusting mechanism and to modify the specifications as necessary.
U5LV12.book Page 17 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS EAU01571 3 EAU00330 EXUP system Sidestand This motorcycle is equipped with Yamaha’s EXUP (EXhaust Ultimate Power valve) system. This system boosts engine power by means of a valve that regulates the diameter of the exhaust pipe. The EXUP system valve is constantly adjusted in accordance with the engine speed by a computercontrolled servomotor. The sidestand is located on the left side of the frame.
U5LV12.book Page 18 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS EAU03741 EW000046 Ignition circuit cut-off system The ignition circuit cut-off system (comprising the sidestand switch, clutch switch and neutral switch) has the following functions. ● It prevents starting when the transmission is in gear and the sidestand is up, but the clutch lever is not pulled. ● It prevents starting when the transmission is in gear and the clutch lever is pulled, but the sidestand is still down.
U5LV12.book Page 19 Thursday, June 27, 2002 5:49 PM INSTRUMENT AND CONTROL FUNCTIONS CD-01E With the engine turned off: 1. Move the sidestand down. 2. Make sure that the engine stop switch is set to “ 3. Turn the key to “ON”. 4. Shift the transmission into the neutral position. 5. Push the start switch. Does the engine start? 3 YES NOTE: This check is most reliable if performed with a warmed-up engine. ”. NO The neutral switch may be defective.
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM PRE-OPERATION CHECKS Pre-operation check list .....................................................................
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM PRE-OPERATION CHECKS EAU01114 4- The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly, even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or loss of tire air pressure could have serious consequences.
U5LV12.book Page 2 Thursday, June 27, 2002 5:49 PM PRE-OPERATION CHECKS ITEM Throttle grip CHECKS • Make sure that operation is smooth. • Check cable free play. • If necessary, have Yamaha dealer adjust cable free play and lubricate cable and grip housing. PAGE 6-22, 6-33 Control cables • Make sure that operation is smooth. • Lubricate if necessary. Drive chain • • • • Check chain slack. Adjust if necessary. Check chain condition. Lubricate if necessary.
U5LV12.book Page 3 Thursday, June 27, 2002 5:49 PM PRE-OPERATION CHECKS NOTE: Pre-operation checks should be made each time the motorcycle is used. Such an inspection can be accomplished in a very short time; and the added safety it assures is more than worth the time involved. _ _ EWA00033 WARNING If any item in the Pre-operation check list is not working properly, have it inspected and repaired before operating the motorcycle.
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM OPERATION AND IMPORTANT RIDING POINTS Starting and warming up a cold engine ............................................. 5-1 Starting a warm engine ..................................................................... 5-3 Shifting .............................................................................................. 5-4 Engine break-in ................................................................................. 5-5 Parking ...................
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM OPERATION AND IMPORTANT RIDING POINTS EAU00372 5- _ 5 EAU00373 EAU00376 WARNING ● Become thoroughly familiar with all operating controls and their functions before riding. Consult a Yamaha dealer regarding any control or function that you do not thoroughly understand. ● Never start the engine or operate it in a closed area for any length of time.
U5LV12.book Page 2 Thursday, June 27, 2002 5:49 PM OPERATION AND IMPORTANT RIDING POINTS 1. Turn the key to “ON” and make sure that the engine stop switch is set to “ ”. ECA00108 CAUTION: The oil level warning light, coolant temperature warning light and fuel level warning light should come on for a few seconds, then go off. If a warning light does not go off, have a Yamaha dealer check the electrical circuit. _ 4. Start the engine by pushing the start switch.
U5LV12.book Page 3 Thursday, June 27, 2002 5:49 PM OPERATION AND IMPORTANT RIDING POINTS not come on for a few seconds, then go off, or if it does not go off after starting with sufficient fuel, have a Yamaha dealer check the electrical circuit. _ 5. After starting the engine, move the starter (choke) back halfway. ECA00055 CAUTION: For maximum engine life, always warm the engine up before starting off. Never accelerate hard when the engine is cold! _ 5 _ 6.
U5LV12.book Page 4 Thursday, June 27, 2002 5:49 PM OPERATION AND IMPORTANT RIDING POINTS EC000048 _ 1. Shift pedal N. Neutral position EAU00423 Shifting Shifting gears lets you control the amount of engine power available for starting off, accelerating, climbing hills, etc. The gear positions are shown in the illustration. CAUTION: ● Even with the transmission in the neutral position, do not coast for long periods of time with the engine off, and do not tow the motorcycle for long distances.
U5LV12.book Page 5 Thursday, June 27, 2002 5:49 PM OPERATION AND IMPORTANT RIDING POINTS 5 EAU00427 EAU02989 To decelerate 1. Apply both the front and the rear brakes to slow the motorcycle. 2. Shift the transmission into first gear when the motorcycle reaches 25 km/h (15.5 mi/h). If the engine is about to stall or runs very roughly, pull the clutch lever in and use the brakes to stop the motorcycle. 3. Shift the transmission into the neutral position when the motorcycle is almost completely stopped.
U5LV12.book Page 6 Thursday, June 27, 2002 5:49 PM OPERATION AND IMPORTANT RIDING POINTS EAU03749* 0–1,000 km (0–600 mi) Avoid prolonged operation 5,000 r/min. EAU00460 Parking above When parking, stop the engine, and then remove the key from the main switch. 1,000–1,600 km (600–1,000 mi) Avoid prolonged operation above 6,000 r/min. EW000058 _ EC000052* CAUTION: After 1,000 km (600 mi) of operation, the engine oil must be changed and the oil filter cartridge replaced.
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR Periodic maintenance ..........................................6-1 Owner’s tool kit ....................................................6-1 Periodic maintenance chart for the emission control system ...................................................6-3 General maintenance and lubrication chart .........6-5 Removing and installing panels ...........................6-8 Checking the spark plugs ..........................
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU00462 6- EAU01790 Safety is an obligation of the owner. Periodic inspection, adjustment and lubrication will keep your vehicle in the safest and most efficient condition possible. The most important points of motorcycle inspection, adjustment, and lubrication are explained on the following pages.
U5LV12.book Page 2 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: If you do not have the tools or experience required for a particular job, have a Yamaha dealer perform it for you. _ _ EW000062 WARNING Modifications not approved by Yamaha may cause loss of performance, excessive emissions, and render the vehicle unsafe for use. Consult a Yamaha dealer before attempting any changes.
U5LV12.book Page 3 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU00471 Periodic maintenance chart for the emission control system CP-03E INITIAL No. ITEM 1 * Valve clearance 6 ROUTINE ODOMETER READINGS 20,000 mi 16,000 mi 12,000 mi 8,000 mi 4,000 mi 600 mi (1,000 km) (7,000 km) (13,000 km) (19,000 km) (25,000 km) (31,000 km) or or or or or or 6 months 12 months 18 months 24 months 30 months 1 month • Check and adjust valve clearance when engine is cold.
U5LV12.book Page 4 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR No. 9 * 10 * ITEM ROUTINE Evaporative emission control system (For California only) • Check control system for damage. • Replace if necessary. Air induction system • Check the air cut valve and reed valve for damage. • Replace the entire air induction system if necessary.
U5LV12.book Page 5 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU00472 General maintenance and lubrication chart INITIAL No. ITEM ROUTINE 1 Engine oil • Replace (warm engine before draining). (See NOTE on page 6-7.) √ 2 Engine oil filter cartridge • Replace at initial 600 mi (1,000 km) or 1 month, and thereafter every 8,000 mi (13,000 km) or 12 months.
U5LV12.book Page 6 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR No. ITEM Swingarm pivot 9 * bearing ROUTINE INITIAL ODOMETER READINGS 600 mi (1,000 km) or 1 month 20,000 mi 16,000 mi 12,000 mi 8,000 mi 4,000 mi (7,000 km) (13,000 km) (19,000 km) (25,000 km) (31,000 km) or or or or or 6 months 12 months 18 months 24 months 30 months • Check bearing assembly for looseness. • Moderately repack every 16,000 mi (25,000 km) or 24 months. #2 √ √ Repack. √ √ Repack.
U5LV12.book Page 7 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR INITIAL No. ITEM ROUTINE 19 * Sidestand switch • Check and clean or replace if necessary. 20 * Chassis fasteners • Check all chassis fitting and fasteners. • Correct if necessary. Muffler and exhaust pipe • Check the screw clamp for looseness.
U5LV12.book Page 8 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR 1. Panel A 2. Panel B 1. Panel C 1. Panel A 2. Screw EAU01122 EAU04003 Removing and installing panels Panels A and C To remove one of the panels Remove the screw, and then pull the panel off as shown. The panels shown above need to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time a panel needs to be removed and installed.
U5LV12.book Page 9 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR 1. Panel C 2. Screw To install the panel Place the panel in the original position, and then install the screw 6 1. Panel B 2. Screw (× 3) EAU01315 Panel B To remove the panel Remove the screws, and then take the panel off. To install the panel Place the panel in the original position, and then install the screws.
U5LV12.book Page 10 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: If any spark plug shows a distinctly different color, the engine could be defective. Do not attempt to diagnose such problems yourself. Instead, have a Yamaha dealer check the motorcycle. _ _ 1. Spark plug cap 1. Spark plug wrench EAU03329 Checking the spark plugs The spark plugs are important engine components, which are easy to check.
U5LV12.book Page 11 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR 3. Install the spark plug with the spark plug wrench, and then tighten it to the specified torque. Tightening torque: Spark plug: 12.5 Nm (1.25 m·kgf, 9.0 ft·lbf) a. Spark plug gap To install a spark plug 1. Measure the spark plug gap with a wire thickness gauge and, if necessary, adjust the gap to specification. 6 Spark plug gap: 0.7–0.8 mm (0.028–0.
U5LV12.book Page 12 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR To change the engine oil (with or without oil filter cartridge replacement) 1. Start the engine, warm it up for several minutes, and then turn it off. 2. Place an oil pan under the engine to collect the used oil. EAU04625 Engine oil and oil filter cartridge The engine oil level should be checked before each ride.
U5LV12.book Page 13 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR Left side 1. Engine oil drain bolt 3. Remove the engine oil filler cap and drain bolt to drain the oil from the crankcase. 6 NOTE: ● Skip steps 4–6 if the oil filter cartridge is not being replaced. ● When draining the engine oil, use a funnel or similar device to keep the oil away from the exhaust pipe. _ 1. Oil filter wrench 2. Oil filter cartridge 1. O-ring 4.
U5LV12.book Page 14 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR 8. Add the specified amount of the recommended engine oil, and then install and tighten the oil filler cap. 1. Torque wrench 6. Install the new oil filter cartridge with an oil filter wrench, and then tighten it to the specified torque with a torque wrench. Tightening torque: Oil filter cartridge: 17 Nm (1.7 m·kgf, 12 ft·lbf) Recommended engine oil: See page 8-1.
U5LV12.book Page 15 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EC000067 CAUTION: If the oil level warning light flickers or remains on, immediately turn the engine off and have a Yamaha dealer check the vehicle. _ _ 10. Turn the engine off, and then check the oil level and correct it if necessary. EAU04879 Coolant The coolant level should be checked before each ride.
U5LV12.book Page 16 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EW000067 Coolant reservoir capacity (up to the maximum level mark): 0.3 L (0.26 Imp qt, 0.32 US qt) WARNING Never attempt to remove the radiator cap when the engine is hot. _ _ EC000080 _ CAUTION: ● If coolant is not available, use distilled water or soft tap water instead. Do not use hard water or salt water since it is harmful to the engine.
U5LV12.book Page 17 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU04299 To change the coolant 1. Place the motorcycle on the centerstand and let the engine cool if necessary. 2. Remove panels A and B. (See pages 6-8 and 6-9 for panel removal and installation procedures.) 3. Place a container under the engine to collect the used coolant. 1. Radiator cap 1. Coolant drain bolt 4. Remove the radiator cap. 5. Remove the coolant drain bolt to drain the cooling system. 6.
U5LV12.book Page 18 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR 8. Pour the recommended coolant into the radiator until it is full. EC000080 _ Recommended antifreeze: High-quality ethylene glycol antifreeze containing corrosion inhibitors for aluminum engines Antifreeze/water mixture ratio: 1:1 Coolant quantity: Total amount: 2.4 L (2.11 Imp qt, 2.54 US qt) Coolant reservoir capacity: 0.3 L (0.26 Imp qt, 0.
U5LV12.book Page 19 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU04051* Cleaning the air filter element The air filter element should be cleaned at the intervals specified in the periodic maintenance and lubrication chart. Clean the air filter element more frequently if you are riding in unusually wet or dusty areas. 1. Remove the seat. (See page 3-11 for seat removal and installation procedures.) 1. Bolt (× 3) 2. Remove the fuel tank bolts. 3.
U5LV12.book Page 20 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR 1. Air filter case cover 2. Screw (× 4) 1. Air filter element 1. Air filter element 7. Pull the air filter element out. 6. Remove the air filter case cover by removing the screws. 6-20 8. Lightly tap the air filter element to remove most of the dust and dirt, and then blow the remaining dirt out with compressed air as shown. If the air filter element is damaged, replace it. 9.
U5LV12.book Page 21 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR ECA00089* EAU00628 Adjusting the carburetors CAUTION: The engine should never be operated without the air filter element installed, otherwise the pistons and/or cylinders may become excessively worn. _ The carburetors are important parts of the engine and emission control system, which require very sophisticated adjustment.
U5LV12.book Page 22 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU00637 Adjusting the valve clearance The valve clearance changes with use, resulting in improper air-fuel mixture and/or engine noise. To prevent this from occurring, the valve clearance must be adjusted by a Yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart. a.
U5LV12.book Page 23 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU03581 CE-22E Tires To maximize the performance, durability, and safe operation of your motorcycle, note the following points regarding the specified tires. Tire air pressure The tire air pressure should be checked and, if necessary, adjusted before each ride. 6 WARNING ● The tire air pressure must be checked and adjusted on cold tires (i.e., when the temperature of the tires equals the ambient temperature).
U5LV12.book Page 24 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EW000094 _ 1. Tire sidewall 2. Tire wear indicators a. Tire tread depth Tire inspection Always check the tires before operating the motorcycle. If a tire tread shows crosswise lines (minimum tread depth), if the tire has a nail or glass fragments in it, or if the side wall is cracked, contact a Yamaha dealer immediately and have the tire replaced. WARNING ● It is dangerous to ride with a worn-out tire.
U5LV12.book Page 25 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EW000080 _ ● ● ● 6 ● WARNING The front and rear tires should be of the same make and design, otherwise the handling characteristics of the motorcycle cannot be guaranteed. After extensive tests, only the tires listed below have been approved for this model by Yamaha Motor Co., Ltd. Always make sure that the valve caps are securely installed to prevent air pressure leakage.
U5LV12.book Page 26 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU03773 Cast wheels To maximize the performance, durability, and safe operation of your motorcycle, note the following points regarding the specified wheels. ● The wheel rims should be checked for cracks, bends or warpage before each ride. If any damage is found, have a Yamaha dealer replace the wheel. Do not attempt even the smallest repair to the wheel. A deformed or cracked wheel must be replaced.
U5LV12.book Page 27 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: If the specified free play cannot be obtained as described above or if the clutch does not operate correctly, have a Yamaha dealer check the internal clutch mechanism. _ _ 1. Clutch lever free play adjusting bolt c. Clutch lever free play a.
U5LV12.book Page 28 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EW000109 WARNING A soft or spongy feeling in the brake pedal can indicate the presence of air in the hydraulic system. If there is air in the hydraulic system, have a Yamaha dealer bleed the system before operating the motorcycle. Air in the hydraulic system will diminish the braking performance, which may result in loss of control and an accident. _ _ 1. Rear brake light switch 2.
U5LV12.book Page 29 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR Rear Front 1. Brake pad wear indicator groove 1. Brake pad wear indicator groove EAU01314 Checking the front and rear brake pads 6 Front brake The front and rear brake pads must be checked for wear at the intervals specified in the periodic maintenance and lubrication chart.
U5LV12.book Page 30 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR Rear brake 1. Minimum level mark Observe these precautions: ● When checking the fluid level, make sure that the top of the brake fluid reservoir is level. ● Use only the recommended quality brake fluid, otherwise the rubber seals may deteriorate, causing leakage and poor braking performance. ● Be careful that water does not enter the brake fluid reservoir when refilling.
U5LV12.book Page 31 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR Drive chain slack: 40–50 mm (1.6–2.0 in) 5. If the drive chain slack is incorrect, adjust it as follows. a. Drive chain slack b. Measurement point: 135 mm (5.3 in) 1. 2. 3. 4. EAU00745 Drive chain slack 6 Axle nut Drive chain slack adjusting bolt Locknut Alignment marks EAU03608 The drive chain slack should be checked before each ride and adjusted if necessary. To adjust the drive chain slack 1.
U5LV12.book Page 32 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: Using the alignment marks on each side of the swingarm, make sure that both chain pullers are in the same position for proper wheel alignment. _ _ EC000096 CAUTION: Improper drive chain slack will overload the engine as well as other vital parts of the motorcycle and can lead to chain slippage or breakage. To prevent this from occurring, keep the drive chain slack within the specified limits.
U5LV12.book Page 33 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU03297 EAU04034 Checking and lubricating the cables Checking and lubricating the throttle grip and cable The operation of all control cables and the condition of the cables should be checked before each ride, and the cables and cable ends should be lubricated if necessary. If a cable is damaged or does not move smoothly, have a Yamaha dealer check or replace it.
U5LV12.book Page 34 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR Recommended lubricant: Lithium-soap-based grease (all-purpose grease) EAU03164 EAU03371 Checking and lubricating the brake and clutch levers Checking and lubricating the centerstand and sidestand The operation of the brake and clutch levers should be checked before each ride, and the lever pivots should be lubricated if necessary.
U5LV12.book Page 35 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU04282 Lubricating the rear suspension The pivoting points of the rear suspension must be lubricated at the intervals specified in the periodic maintenance and lubrication chart. EAU02939 Checking the front fork The condition and operation of the front fork must be checked as follows at the intervals specified in the periodic maintenance and lubrication chart.
U5LV12.book Page 36 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU00794 EAU01144 Checking the steering Checking the wheel bearings Worn or loose steering bearings may cause danger. Therefore, the operation of the steering must be checked as follows at the intervals specified in the periodic maintenance and lubrication chart. 1. Place a stand under the engine to raise the front wheel off the ground.
U5LV12.book Page 37 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR • EXTERNAL: Flush with plenty of water. • INTERNAL: Drink large quantities of water or milk and immediately call a physician. • EYES: Flush with water for 15 minutes and seek prompt medical attention. ● Batteries produce explosive hydrogen gas. Therefore, keep sparks, flames, cigarettes, etc., away from the battery and provide sufficient ventilation when charging it in an enclosed space.
U5LV12.book Page 38 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR 2. Remove the blown fuse, and then install a new fuse of the specified amperage. EC000102 _ CAUTION: keep the battery ● Always charged. Storing a discharged battery can cause permanent battery damage. ● To charge a sealed-type (MF) battery, a special (constantvoltage) battery charger is required. Using a conventional battery charger will damage the battery.
U5LV12.book Page 39 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR 1. Headlight bulb cover 2. Headlight coupler 1. Headlight bulb holder EAU04226 Replacing a headlight bulb 6 This motorcycle is equipped with two quartz bulb headlights. If a headlight bulb burns out, replace it as follows. 1. Remove panel B. (See page 6-9 for panel removal and installation procedures.) 2. Disconnect the headlight coupler, and then remove the bulb cover. 3.
U5LV12.book Page 40 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EC000104 CAUTION: Take care not to damage the following parts: ● Headlight bulb Do not touch the glass part of the headlight bulb to keep it free from oil, otherwise the transparency of the glass, the luminosity of the bulb, and the bulb life will be adversely affected. Thoroughly clean off any dirt and fingerprints on the headlight bulb using a cloth moistened with alcohol or thinner.
U5LV12.book Page 41 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR 1. Tail/brake light bulb cover 1. Socket EAU03961 Replacing a tail/brake light bulb 6 1. Remove the seat. (See page 3-11 for seat removal and installation procedures.) 2. Remove the tail/brake light bulb cover. 1. Screw 3. Remove the socket (together with the bulb) by turning it counterclockwise. 4. Remove the defective bulb by pushing it in and turning it counterclockwise. 5.
U5LV12.book Page 42 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR ECA00065 CAUTION: Do not overtighten the screw, otherwise the lens may break. _ _ 1. Wheel axle 2. Front wheel axle pinch bolt EAU03962 Front wheel 1. 2. 3. 4. 3. Remove the brake hose holder on each side by removing the bolts. 4. Remove the brake caliper on each side by removing the bolts. To remove the front wheel EW000122 _ WARNING It is advisable to have a Yamaha dealer service the wheel.
U5LV12.book Page 43 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU03963 To install the front wheel 1. Lift the wheel up between the fork legs. 2. Insert the wheel axle. 3. Lower the front wheel so that it is on the ground. 4. Install the brake calipers by installing the bolts. NOTE: Make sure that there is enough space between the brake pads before installing the brake calipers onto the brake discs. _ 6 Tightening torques: Wheel axle: 72 Nm (7.
U5LV12.book Page 44 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR 1. 2. 3. 4. 5. Bolt (× 2) Brake torque rod Brake torque rod bolt Brake torque rod nut Brake caliper bracket 1. Axle nut 2. Drive chain slack adjusting bolt 3. Locknut 3. Disconnect the brake torque rod from the brake caliper by removing the nut and the bolt. 4. Remove the axle nut, then the brake caliper by removing the bolts. 6. Turn the drive chain slack adjusting bolts fully in direction a. 7.
U5LV12.book Page 45 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR 5. Install the brake caliper by installing the bolts. NOTE: Make sure that there is enough space between the brake pads before installing the brake caliper onto the brake disc. _ _ EAU03895 6 To install the rear wheel 1. Place the wheel and the brake caliper bracket in the original position. 2.
U5LV12.book Page 46 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU02990 Troubleshooting charts Starting problems or poor engine performance EW000125 WARNING Keep away open flames and do not smoke while checking or working on the fuel system. _ _ 1. Fuel There is enough fuel. Check the compression. There is no fuel. Supply fuel. There is compression. Check the ignition. There is no compression. Have a Yamaha dealer check the vehicle.
U5LV12.book Page 47 Thursday, June 27, 2002 5:49 PM PERIODIC MAINTENANCE AND MINOR REPAIR Engine overheating EW000070 _ WARNING Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM MOTORCYCLE CARE AND STORAGE Care .................................................................................................. 7-1 Storage ..............................................................................................
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM MOTORCYCLE CARE AND STORAGE EAU03426 7- Care While the open design of a motorcycle reveals the attractiveness of the technology, it also makes it more vulnerable. Rust and corrosion can develop even if high-quality components are used. A rusty exhaust pipe may go unnoticed on a car, however, it detracts from the overall appearance of a motorcycle.
U5LV12.book Page 2 Thursday, June 27, 2002 5:49 PM MOTORCYCLE CARE AND STORAGE ● Do not use any harsh chemical products on plastic parts. Be sure to avoid using cloths or sponges which have been in contact with strong or abrasive cleaning products, solvent or thinner, fuel (gasoline), rust removers or inhibitors, brake fluid, antifreeze or electrolyte.
U5LV12.book Page 3 Thursday, June 27, 2002 5:49 PM MOTORCYCLE CARE AND STORAGE ECA00012 CAUTION: Do not use warm water since it increases the corrosive action of the salt. _ _ 2. Apply a corrosion protection spray on all metal, including chromeand nickel-plated, surfaces to prevent corrosion. 7 After cleaning 1. Dry the motorcycle with a chamois or an absorbing cloth. 2. Immediately dry the drive chain and lubricate it to prevent it from rusting. 3.
U5LV12.book Page 4 Thursday, June 27, 2002 5:49 PM MOTORCYCLE CARE AND STORAGE ECA00013 _ CAUTION: ● Apply spray oil and wax sparingly and make sure to wipe off any excess. ● Never apply oil or wax to any rubber and plastic parts, but treat them with a suitable care product. ● Avoid using abrasive polishing compounds as they will wear away the paint. Storage Short-term Always store your motorcycle in a cool, dry place and, if necessary, protect it against dust with a porous cover.
U5LV12.book Page 5 Thursday, June 27, 2002 5:49 PM MOTORCYCLE CARE AND STORAGE 7. Check and, if necessary, correct the tire air pressure, and then lift the motorcycle so that both of its wheels are off the ground. Alternatively, turn the wheels a little every month in order to prevent the tires from becoming degraded in one spot. 8. Cover the muffler outlet with a plastic bag to prevent moisture from entering it. 9. Remove the battery and fully charge it.
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM SPECIFICATIONS Specifications ....................................................................................
E_5lv_Spec.fm Page 1 Wednesday, July 3, 2002 8:55 AM SPECIFICATIONS EAU01038 8- Specifications CS-01E Model FZS1000/FZS1000S Engine oil Type Dimensions Overall length Overall width Overall height 2,125 mm (83.7 in) 1,190 mm (46.9 in) Seat height 820 mm (32.3 in) Wheelbase 1,450 mm (57.1 in) Ground clearance Minimum turning radius 0 765 mm (30.1 in) 30 2,900 mm (114.
U5LV12.book Page 2 Thursday, June 27, 2002 5:49 PM SPECIFICATIONS Cooling system capacity (total amount) 2.4 L (2.11 Imp qt, 2.54 US qt) Number of drive chain sprocket teeth (front/rear) 16/44 Air filter Dry type element Transmission type Constant-mesh 6-speed Operation Left foot Fuel Type UNLEADED GASOLINE ONLY Gear ratio Fuel tank capacity 21 L (4.6 Imp gal, 5.5 US gal) 1st 2.500 Fuel reserve amount 4 L (0.9 Imp gal, 1.1 US gal) 2nd 1.842 Carburetor 3rd 1.
U5LV12.book Page 3 Thursday, June 27, 2002 5:49 PM SPECIFICATIONS Rear Wheels Type Tubeless tire Size 180/55 ZR17 (73W) Type 180/55 ZR17 M/C (73W) Size Manufacturer/ model Front Bridgestone / BT020R U Rear Type FZS1000/FZS1000S 189 kg (417 lb) FZS1000C/FZS1000SC 188 kg (415 lb) Size Front 250 kPa (2.50 kgf/cm2, 36 psi) Type Dual disc brake 270 kPa (2.
U5LV12.book Page 4 Thursday, June 27, 2002 5:49 PM SPECIFICATIONS Wheel travel Front Coolant temperature warning light 140 mm (5.5 in) Rear 135 mm (5.3 in) Electrical system Ignition system T.C.I. (digital) Charging system Model A.C.
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM CONSUMER INFORMATION Identification numbers ....................................................................... 9-1 Key identification number .................................................................. 9-1 Vehicle identification number ............................................................. 9-1 Model label ........................................................................................ 9-2 Reporting safety defects .................
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM CONSUMER INFORMATION EAU01039 9- EAU02944 Identification numbers Record the key identification number, vehicle identification number and model label information in the spaces provided below for assistance when ordering spare parts from a Yamaha dealer or for reference in case the vehicle is stolen. 1. Key identification number 1. KEY IDENTIFICATION NUMBER: CA-02E 2.
U5LV12.book Page 2 Thursday, June 27, 2002 5:49 PM CONSUMER INFORMATION 1. Model label EAU01050 Model label The model label is affixed to the frame under the seat. (See page 3-11 for seat removal and installation procedures.) Record the information on this label in the space provided. This information will be needed when ordering spare parts from a Yamaha dealer.
U5LV12.book Page 3 Thursday, June 27, 2002 5:49 PM CONSUMER INFORMATION EAU01051 Reporting safety defects If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation, U.S.A.
U5LV12.
U5LV12.book Page 5 Thursday, June 27, 2002 5:49 PM CONSUMER INFORMATION EAU01874 Maintenance record Copies of work orders and/or receipts for parts purchased and installed on your motorcycle will be required to document that maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder that maintenance work is required. It is not acceptable proof of maintenance work.
U5LV12.
U5LV12.book Page 7 Thursday, June 27, 2002 5:49 PM CONSUMER INFORMATION EAU02918 YAMAHA MOTOR CORPORATION, U.S.A.
U5LV12.
U5LV12.book Page 9 Thursday, June 27, 2002 5:49 PM CONSUMER INFORMATION EAU01063 YAMAHA EXTENDED SERVICE (Y.E.S.
U5LV12.
U5LV12.book Page 1 Thursday, June 27, 2002 5:49 PM INDEX A D K Accessories and replacement parts .......6-26 Air filter element, cleaning ......................6-19 Dimmer switch......................................... 3-6 Drive chain, lubricating .......................... 6-32 Drive chain slack ................................... 6-31 Adjusting .......................................... 6-31 Checking.......................................... 6-31 Key identification number .........................
U5LV12.book Page 2 Thursday, June 27, 2002 5:49 PM INDEX Shifting .................................................... 5-4 Decelerating....................................... 5-5 Shift points ......................................... 5-5 Starting out and accelerating.............. 5-4 Shift pedal ............................................... 3-7 Shock absorber assembly, adjusting ..... 3-14 Sidestand .............................................. 3-17 Spark plugs, checking ...........................
OWNER’S MANUAL FZS1000R FZS1000RC FZS1000SR FZS1000SRC YAMAHA MOTOR CO., LTD. PRINTED ON RECYCLED PAPER PRINTED IN JAPAN 2002.06-1.
