Owner’s Manual Before using the instrument, be sure to read “PRECAUTIONS” on page 5.
The model number, serial number, power requirements, etc., may be found on or near the name plate, which is at the bottom of the unit. You should note this serial number in the space provided below and retain this manual as a permanent record of your purchase to aid identification in the event of theft. Model No. Serial No.
For USA FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
For CANADA This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadaʼs licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING Please keep this manual in a safe and handy place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Power supply Water warning • Do not place the power cord near heat sources such as heaters or radiators.
CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the product or other property. These precautions include, but are not limited to, the following: Location Handling • Do not place the product in an unstable position or a location with excessive vibration, where it might accidentally fall over and cause injury. • Do not insert your finger or hand in any gaps on the product.
NOTICE To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below. Handling • Do not connect this product to a public Wi-Fi and/or Internet service directly. Only connect this product to the Internet through a router with strong password protections. Consult your router manufacturer for information on optimum security practices.
Information About copyrights The copyright of the “content” *1 installed in this product belongs to Yamaha Corporation or its copyright holder. Except as permitted by copyright laws and other relevant laws, such as copying for personal use, it is prohibited to “reproduce or divert” *2 without the permission of the copyright holder. When using the content, consult with a copyright expert.
Congratulations! You are the proud owner of an extraordinary electronic keyboard. In addition to its stylish curved design, the Yamaha Genos2 combines the most advanced tone generation technology with state-of-the-art digital electronics to give you stunning sound with maximum musical versatility—a beautiful instrument from every perspective.
About the Manuals This instrument has the following documents and instructional materials. Included Documents • Owner’s Manual (this book) Provides overall explanations of Genos2 basic functions. Online Materials (Downloadable from the web) • Reference Manual (only in English, French, German, Italian, Dutch, Polish, and Chinese) Explains advanced features of the instrument, such as creating original Styles, Songs and Multi Pads, and making the settings of specific parameters.
Main Features Extraordinarily expressive and realistic Voices The Genos name is synonymous with formidable Voice quality. Genos2 stays true to this ethos with beautiful new pianos, powerful brass and legendary FM Voice technology from the Yamaha DX7, combining to give you the richest musical experience. Powerful DSP effect processing for enhancing the sound Main Features From Reverb to Distortion, Rotary Speaker to Compressor, Genos2 boasts unprecedented DSP power.
Contents PRECAUTIONS 5 NOTICE 7 Information 8 Included Accessories 9 About the Manuals 10 Main Features 11 Using Genos2—a Broad Overview 14 Major Functions 16 Panel Controls and Terminals 18 Starting Up 22 Audio Connections................................................................................................................................................................................................... 22 Power Supply..........................................................
Expressively Controlling Your Performance.................................................................................................................................................... 69 Playing and Controlling Super Articulation Voices...................................................................................................................................... 71 Controlling Multi Pad Playback......................................................................................................
Using Genos2—a Broad Overview This section provides a helpful overview of the wide range of functions available in Genos2, and places you can find necessary information on those topics. If you need help in understanding a feature, function or operation—or need to have a general understanding of what Genos2 can do and how to effectively use it—look through this section. OM : Genos2 Owner’s Manual (this book). The relevant chapter names are shown after this symbol.
Using Genos2 with a computer • Connecting a computer to the instrument OM Connections • Transferring files (Songs, Styles, Backup files, etc) Computer Related Operations* Using Genos2—a Broad Overview • Playing back Songs on a computer via the instrument sounds • Recording your keyboard performance to a computer • Obtaining the Expansion Packs made by Yamaha (also called “Premium Packs”) Genos2 product website https://manual.yamaha.
Major Functions This section briefly explains the main functions of Genos2, to help you better understand the overall capabilities of the instrument. Styles—Rhythm and Auto Accompaniment— Genos2 features a variety of accompaniment and rhythmic backing patterns (called “Styles”) in a variety of different musical genres including pop, jazz, and many others.
Registration Memory—Saving and recalling custom panel setups— The Registration Memory function allows you to save (or “register”) virtually all panel settings to a Registration Memory button, and then instantly recall your custom panel settings by simply pressing a single button. The registered settings for ten Registration Memory buttons are saved as a single Registration Bank (file).
Panel Controls and Terminals Top panel !6 !7 r e w q o !0 t !4 !9 !1 !5 @ !2 y !3 u i 1 [P] (Standby/On) switch............................. page 23 Turns on the instrument’s power or sets to standby. 2 [MASTER VOLUME] dial............................... page 23 Adjusts the overall volume. 3 [MIC GAIN] knob..........................................page 110 Adjusts the input sensitivity from the MIC INPUT jack. 4 MIC buttons..................................................
!8 Panel Controls and Terminals !7 @8 @6 @7 @0 !9 @4 @1 @2 @3 @5 ^ LIVE CONTROL (view/knobs/sliders) ..............................................................pages 26, 62 For controlling sounds in real time. & Touch LCD and related controls.................. page 30 * Gateway buttons.......................................... page 28 For calling up the Home display and other particular displays directly. ( ASSIGNABLE [1]–[3], [A]–[F] buttons..........
Rear Panel and Bottom #0 @9 @9 #1 #2 #3 #4 $3 J Slots...................................................... pages 21, 124 The four slots nearest the display panel are for connecting the music rest brackets; the other slots are for connecting the speaker brackets of the optional GNS-MS01 speakers. K [TO RIGHT SPEAKER] jack.......................... page 124 For connecting an optional set of speakers. L [HDMI] terminal.........................................
@9 #6 #5 $2 @9 $0 #7 1 Attach the two music rest brackets to the inside slots on the rear panel. 2 Attach the music rest to the brackets. 1 #9 $1 Panel Controls and Terminals Attaching the Music Rest #8 Using the USB TO DEVICE terminal underneath the instrument Genos2 has a convenient extra USB TO DEVICE terminal underneath the instrument, allowing you to semipermanently install USB flash drive that will always be available and be protected from harm or loss.
Starting Up Audio Connections Connecting headphones or a speaker system Since the instrument has no built-in speakers, you’ll need to use external equipment, such as headphones or a speaker system, to hear the sound of the instrument. Using headphones Connect a set of headphones to the [PHONES] jack. Using a speaker system For instructions on installing the optional speakers GNS-MS01, refer to page 124. For instructions on connecting other speakers, refer to page 112.
Power Supply 1 Connect the supplied power cord to the [AC IN] jack on the instrument’s rear panel. WARNING Use only the supplied power cord. WARNING Connect the other end of the power cord to an AC outlet. Starting Up 2 When setting up the product, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet.
Auto Power Off function To prevent unnecessary power consumption, this instrument features an Auto Power Off function that automatically turns the power off if the instrument is not operated for a specified period of time. The amount of time that elapses before the power is automatically turned off is approximately 30 minutes by default; however, you can change the setting (page 24). Disabling Auto Power Off (simple method) Turn the power on while holding down the lowest key on the keyboard.
Changing the Brightness of Displays and Lighting Buttons Here you can change the brightness of the lighting buttons. 1 Call up the operation display (Utility) (step 1 on page 24). 2 Call up the “Touch Screen/Display” display. 3 Change the settings by touching the display. Touch [Touch Screen/Display] on the display. Starting Up Main Display Touch the slider to adjust the brightness of the Main display.
Display Structure Genos2 has two displays (the LCD Touch Screen and the LIVE CONTROL view) and lighting buttons for visually helping you to understand the current status. LIVE CONTROL view (Sub Display) LCD (Main Display; touch screen) The LIVE CONTROL view indicates the parameters operated when you use the six LIVE CONTROL knobs and nine LIVE CONTROL sliders. For details on the display structure, see page 27. The LCD indicates the parameters and values related to the currently selected operation.
LIVE CONTROL View (Sub Display) Structure In the LIVE CONTROL view, you can see the parameters status controlled by the LIVE CONTROL knobs and the LIVE CONTROL sliders. There are two displays: knobs and sliders, and you can switch between these two displays while operating the instrument. To switch between the displays without changing parameter values, simply press the [KNOB ASSIGN]/[SLIDER ASSIGN] buttons.
Main Display Structure—Using the Gateway Buttons The Gateway buttons are just as their name suggests—a convenient, easy-to-understand “gateway” to Genos2. When the instrument is turned on, the Home display is called up. However, as you operate the instrument, you can directly call up the Home display and other desired displays directly by pressing the Gateway buttons on the front panel. Other functions and various detailed settings for the instrument can be accessed from the Menu display.
Display Structure Menu display By touching each of the icons, you can call up various functions, such as Song Score, Volume Balance and other detailed settings (page 33). Voice Part Setup display This is for making detailed settings such as Voice Edit and Effect settings of the keyboard parts. For details on the Voice Part Setup display, refer to the Reference Manual on the website. Playlist display This is for selecting and editing Playlists (page 100).
Basic Operations Display Configuration This section covers the most often used displays: Home, File Selection and Menu. The Home display appears when the power is turned on. The term “File Selection display” refers to all the various displays called up on the instrument from which you can select files. The Menu display is a portal display for various functions and can be called up by pressing the [MENU] button.
Information area in the Home display q r w t y e u Basic Operations 1 Bar/Beat/Tempo Displays the current position (bar/beat/tempo) in Style playback or MIDI Song playback. By rotating the Data dial, you can call up the Tempo pop-up display and adjust the tempo. 2 Upper Octave/Transpose Displays the amount that the upper octave value is shifted, and the amount of master transposition in semitone units (page 61). 3 Clock The current time is shown here.
File Selection Display The File Selection display is for selecting a Voice, Style, Song, Multi Pads and other items. You can call up this display by touching the name of the Voice, Style or Song on the Home display, or by pressing one of the VOICE SELECT buttons or [STYLE] button, etc. The displays are different, depending on which file type is selected. For example, when Voice is selected, the Voice Selection display is called up.
Menu Display This is the portal display for using various functions and can be called up by pressing the [MENU] button. Basic Operations Various convenient functions are shown via icons. Touching each of them calls up the corresponding function. This list consists of two pages, which you can select by touching [Menu 1] or [Menu 2]. For brief information on each function, refer to the “Function List” (page 122). NOTE You can also change pages by flicking horizontally.
Display-based Controls The display of this instrument is a special touch screen that allows you to select or change the desired parameter by simply touching the corresponding setting on the display. You can also decrease/increase the value in small steps by rotating the Data dial or pressing the [DEC]/[INC] button. Using the display (touch screen) NOTICE • Do not use any sharp or hard tools to operate the touch screen. Doing so may damage the display. • Take care not to leave objects on the touch LCD.
Using the Data dial, [ENTER] button, and [DEC]/[INC] buttons Depending on the display, the Data dial and the buttons can be used in the following two ways. Adjusting the parameter values After selecting the desired parameter, use the Data dial or the [DEC]/[INC] buttons to adjust the value. This is useful if you have difficulty adjusting by touching on the display, or want finer control over the adjustment.
Calling up the Desired Display Instantly—Direct Access With the convenient Direct Access function, you can instantly call up the desired display—with just a single additional button press. Refer to the “Direct Access Chart” on page 126 for a list of the displays that can be called up with the Direct Access function. 1 Press the [DIRECT ACCESS] button. 2 Press the button (or move the knob, slider, joystick or connected pedal) corresponding to the desired setting display to instantly call up that display.
File Management Data you have created such as recorded Song and edited Voice can be saved as files to the instrument (referred to as “User drive”) and a USB flash drive. If you’ve saved a lot of files, you may have trouble finding the desired file quickly. To make operation easier, you can organize your files in folders, rename the files, delete unnecessary files, etc. These operations are done in the File Selection display.
Creating a new folder Folders can be created, named and organized as desired, making it easier to find and select your original data. 1 In the File Selection display, touch the User tab (page 32) then select the location to which you want to create a new folder. To show the next higher level folder, touch (Up). 2 Touch 3 Touch [New Folder] to call up the Character Entry window. 4 Input the name of the new folder (page 40). (File Edit) to call up the File Edit pop-up window.
6 Select the desired destination (path) to paste the files/folders. 7 Touch [Copy here] or [Move here] to paste the files/folders you’ve selected in step 4. NOTE To cancel this operation, touch [Cancel] before going to step 7. The pasted file/folder appears on the display at the appropriate position among the files in alphabetical order. Deleting files/folders Basic Operations You can delete files/folders.
Entering Characters This section covers how to enter characters for naming your files/folders, inputting keywords on searching file, etc. Entering characters is done in the display shown below. 1 Touch the character type. 2 Touch [L]/[R], rotate the Data dial or the press [DEC]/[INC] buttons to move the cursor to the desired location. 3 Input the desired character one by one. Touching [Symbol] (or [abc]) switches between entering symbols or Roman letters (and numbers).
Locking the Panel Settings (Panel Lock) When the panel settings are locked, nothing happens if you press any panel buttons. For example, when you take a break during your performance and leave the instrument unattended, this feature protects the panel settings from being accessed by others. 1 Call up the Panel Lock display via [MENU] à [Panel Lock]. 2 Input a four-number PIN code by touching the numeric keypad, then touch [OK] to enter it.
Quick Guide—for Performing on Genos2 Manual panel settings and performing a single song Playing the keyboard with Styles (Auto Accompaniment) Optimum panel settings for the current Style (One Touch Setting) ... p. 47 Setting up the Style ... p. 44 Calling up the most appropriate panel settings (Keyboard Parts, Harmony/Arpeggio, or Multi Pads) for the selected Style. or Setting up the Voices ... p. 48 (Setting up keyboard parts) Setting up Harmony/ Arpeggio ... p.
p. 62 Setting up Vocal Harmony ... p. 80 Quick Guide—for Performing on Genos2 Assigning functions to controllers ... Playing with Styles Operations during performance: p. 66 Setting up Multi Pads ... p. 59 Assigning functions to controllers ... p. 62 Setting up Vocal Harmony ... p. 80 Singing with Song playback Operations during performance: p. 82 Registering the Registration Memory in a Playlist ... p. 100 Editing the Playlist for your live performance set list ... p.
1 Operation Guide Playing with Styles—Setups This section gives you basic steps on how to enhance your keyboard performance with Styles (Rhythm and Auto Accompaniment). Go through the various instructions below to completely set up your performance of a single song: Style, Keyboard Part (Voice), Multi Pad, and various types of controllers. The settings made in this section can be collectively stored in the Registration Memory as one song setting (page 96).
Style Characteristics The particular type of Style is indicated the upper left of the Style name in the Style Selection display. The defining characteristics of these Styles and their performance advantages are described below. 1 Playing with Styles—Setups • Session: These Styles provide even greater realism and authentic backing by mixing in original chord types and changes, as well as special riffs with chord changes, with the Main sections.
Adjusting the tempo The TEMPO [−] and [+] buttons let you change the playback tempo of the Metronome, Style and MIDI Song. The tempo of the Style and MIDI Song can also be adjusted via the [TAP TEMPO] button. NOTE If you want to adjust the tempo of an Audio Song, use the Time Stretch function on page 84. TEMPO [−]/[+] buttons Press the TEMPO [−] or [+] button to call up the Tempo pop-up display. Use the TEMPO [−]/[+] buttons to decrease or increase the tempo over a range of 5–500 beats per minute.
Optimum Panel Settings for the Current Style (One Touch Setting) One Touch Setting is a powerful and convenient feature that automatically calls up the most appropriate panel settings (Voices, effects, etc.) for the currently selected Style, with the touch of a single button. If you’ve already decided which Style you wish to use, you can have One Touch Setting automatically select the appropriate Voice for you. 1 Select the desired Style (steps 1–2 on page 44).
Setting up Keyboard Parts There are four keyboard parts for your manual performance: LEFT, RIGHT 1, RIGHT 2 and RIGHT 3, and each part has one Voice. You can combine these parts by using the PART ON/OFF buttons to create luscious instrument textures and convenient performance combinations.
Holding the LEFT part Voice (Left Hold) By turning on the PART ON/OFF [LEFT HOLD] button when the LEFT part is ON, the LEFT part Voice is held even when the keys are released. Non-decaying Voices such as strings are held continuously, while decay-type Voices such as piano decay more slowly (as if the sustain pedal has been pressed). This function is convenient when used along with Style playback since the sound of the chords matching Style playback are maintained.
1 Split Point (Style + Left) Sets Split Point (Style) and Split Point (Left) to the same note. In this case, the Chord Section and the LEFT part section occupy the same area. Specify the Split Point directly from the keyboard by simultaneously holding [Style + Left] on the display and pressing the desired key on the keyboard. Split Point (Style + Left) Chord + LEFT part section (Left-hand section) 2 Split Point (Style, Left, Right 3) Right-hand section Sets each Split Point individually.
Specifying chords with your right hand for Style playback By changing the Chord Detection area from the left-hand section to the right-hand section, you can play a bass line with your left hand while using your right hand to play chords for controlling Style playback. 1 Call up the Split Point/Fingering window. 2 Make the necessary settings by touching the display. [MENU] à [Split & Fingering] 1 Playing with Styles—Setups Chord Detection Area Select “Upper.
Selecting a Voice for Each Keyboard Part 1 Press the VOICE SELECT button corresponding to the desired part. The Voice Selection display (for the desired part) appears. You can also call up the Voice Selection display via the Home display (page 30) or the Voice Part Setup display (Reference Manual on the web site). 2 Touch the desired Voice. NOTE For basic operations of the Voice Selection display, refer to “File Selection Display” (page 32).
Creating Original Organ Flutes Voices Genos2 uses advanced digital technology to recreate the legendary sound of vintage organs. Just as on a traditional electronic organ, you can create your own sound by increasing and decreasing the levels of the flute footages. The created Voice can be saved for future recall. NOTE The term “footage” is a reference to the sound generation of traditional pipe organs, in which the sound is produced by pipes of different lengths (in feet).
Using Ensemble Voices These are special settings of the keyboard parts that feature multiple Voices, used in realistic ensemble combinations, such as brass section and string quartet. Up to four special parts or instruments are provided within a single Voice. But rather than just being a combination, the parts are dynamically assigned to the notes, and are distributed among the intervals you play in exceptionally natural, musical ways—as if four different players were actually playing the parts live.
To return to the Home display Press the [EXIT] button or the [HOME] button. The Voice area shows the Ensemble Voice name. To call up the Voice Selection display again to select other presets, touch the Voice area of the Home display. 1 Playing with Styles—Setups Exiting from the Ensemble Voice mode 1 Press any one of the VOICE SELECT buttons to call up the Voice Selection display. 2 Select a Voice other than an Ensemble Voice.
Setting up Keyboard Harmony/Arpeggio You can apply the Keyboard Harmony or Arpeggio features to enhance or change the sound of the Right-hand parts (RIGHT 1–3). Keyboard Harmony applies performance effects such as harmony (duet, trio, etc.), echo, tremolo and trill to the notes played in the Right-hand section. The Arpeggio function lets you play arpeggios (broken chords) by simply pressing the notes of the chord.
• When the [ACMP] button is off and the LEFT part is on: Split Point (Left) RIGHT 1–3 parts LEFT part and chord section for Harmony effect 1 • When both the [ACMP] button and the LEFT part are on: Split Point (Style) Split Point (Left) Playing with Styles—Setups LEFT part RIGHT 1–3 parts Chord section for Style playback and Harmony effect • Multi Assign The Multi Assign effect automatically assigns the notes of chords you play on the right-hand section of the keyboard to separate parts (Voices).
5 Play a note or notes to trigger the Arpeggio. The arpeggiated phrase differs depending on the notes played. To turn off the effect, turn the [HARMONY/ARPEGGIO] button off. 58 Genos2 Owner’s Manual NOTE • By using the Arpeggio Quantize function, Arpeggio playback can be synchronized with Song/Style playback, allowing any slight imperfections in the timing to be corrected. This can be set in the display: [MENU] à [VoiceSetting] à [S.Art2/ Arpeggio].
Setting up Multi Pads Selecting Multi Pads 1 Press the MULTI PAD CONTROL [SELECT] button to call up the Multi Pad Bank Selection display. NOTE You can also call up the Multi Pad Selection display via the Home display (page 30). 1 Touch the desired Multi Pad Bank. 3 If necessary, try out the selected Multi Pad(s). Simply press the MULTI PAD CONTROL [1]–[4] buttons to start playback of the corresponding phrase. To stop playback, press the [STOP] button.
Memorizing Original Panel Settings to One Touch Setting You can memorize your original panel settings (mainly Style, Voices, and Multi Pads) to a One Touch Setting (OTS). The newly created One Touch Setting will be saved in the User drive or a USB flash drive as a Style, and you can call up the One Touch Setting as a part of the Style. 1 Select the desired Style to memorize your One Touch Setting. 2 Make the desired panel settings, such as those for Voices and Effects.
Changing the Pitch of the Keyboard Transposing the pitch in semitones (TRANSPOSE [−]/[+]buttons) The TRANSPOSE [−]/[+] buttons transpose the overall pitch of the instrument (the keyboard sound, Style playback, MIDI Song playback, and so on) in semitone steps (from −12 to 12). To instantly reset the transpose value to 0, press the [−] and [+] buttons simultaneously. Master Transposes the pitch of the entire sound, with the exception of the Audio Song and input sound from a microphone or the AUX IN jacks.
Setting up Assignable Controllers You can assign parameters and functions to the LIVE CONTROL knobs/sliders, the ASSIGNABLE [A]–[F] and [1]–[3] buttons, joystick, or optional footswitches for quick operations and expressive control during your keyboard performance. The setup of assignable controllers is stored/recalled from the registration memory so you can change them all together.
Operating the LIVE CONTROL knobs/sliders Operating the LIVE CONTROL knobs • LEDs around each knob display the current value of the parameter corresponding to the knob, in the current Knob Assign Type. 1 • When any knob is operated, the LIVE CONTROL view automatically displays the current Knob Assign Type and current values (page 27). Playing with Styles—Setups • Operating a knob changes the corresponding parameter from its current value.
Selecting the Assign Types of the LIVE CONTROL joystick Each setup of assigned parameters for the joystick is called a “Joystick Assign Type.” There are three Joystick Assign Types (1–3) and they can be switched in sequence by pressing the ASSIGNABLE [1] button by default. The selected Assign Types for the joystick will be reset when the power is turned off; however, these can be conveniently saved to Registration Memory (page 96).
Assigning functions or shortcuts to the ASSIGNABLE buttons You can assign various control functions or shortcuts to the ASSIGNABLE [A]–[F] and [1]–[3] buttons, allowing you to quickly operate or call up the desired function. 1 Call up the Assignable display via [MENU] à [Assignable]. 1 2 Double-tap (touch twice) the desired item from the “Assignable Buttons” area. 3 Touch the desired function. Playing with Styles—Setups 2 The function selection pop-up window appears.
2 Operation Guide Playing with Styles—Operations While Performing If you’ve made all desired settings for a single song (in the previous sections), now you’re ready to play the keyboard. This section mainly explains the various Style-related operations you’ll use during your keyboard performance: Style playback, applying expressive effects, and Multi Pad playback. Operating Style Playback Starting and stopping Style playback [START/STOP] button Starts playback of the rhythm part of the current Style.
Fading In/Out The Fade In/Out function produces smooth fade-ins and fade-outs when starting/stopping the playback of a Style or Song. By default, this function can be used by pressing the ASSIGNABLE [2] button. • To start playback with a fade in: When playback is stopped, press the button to which this function has been assigned. Then press the [START/STOP] button for Style (or the [PLAY/PAUSE] button for MIDI Song).
[BREAK] button This lets you add dynamic breaks in the rhythm of the accompaniment. Press the [BREAK] button during Style playback. When the one-measure Break pattern finishes playing, Style playback automatically shifts to the Main section. About the lamp status of the section buttons (INTRO/MAIN VARIATION/BREAK/ENDING) • Red: The section is currently selected. • Red (flashing): The section will be played next, following the currently selected section.
4 Press the CHORD LOOPER [ON/OFF] button to stop loop playback. The playback of the chord sequence is stopped, and the Style will return to normal playback. NOTE • The [ON/OFF] button lights in blue to indicate the chord sequence has been recorded and loop playback stops. • Pressing the [ON/OFF] button restarts loop playback of the chord sequence recorded on steps 1–3.
Using the LIVE CONTROL joystick By default, by moving the joystick in a horizontal (X) or vertical (Y) direction, you can bend the notes up or down, or apply modulation effects. Move the joystick to control the sound while playing the keyboard. +Y −X +X −Y X: Pitch Bend Bends notes up (by moving the joystick to the right) or down (by moving the joystick to the left) while playing the keyboard. This is applied to all keyboard parts (RIGHT 1–3 and LEFT).
Applying sustain to the RIGHT 1–3 Voices The [SUSTAIN] button turns the Sustain function on and off. When on, all notes played on the keyboard with the right-hand parts (RIGHT 1, 2, 3) have a longer sustain. Playing and Controlling Super Articulation Voices The Super Articulation Voices (S.Art Voices and S.Art2 Voices) enable you to create subtle, very realistic expressive nuances, simply by how you play. The Voice type (S.Art, S.
Adding articulation effects by the [ART. 1]–[ART. 3] buttons When you select a Super Articulation Voice, the [ART. 1]/[ART. 2]/[ART. 3] buttons may light in blue. Pressing a lit button adds the effect (buttons not lit have no effect). Below are three examples of Super Articulation Effects by the buttons. Example 1 Pressing the available [ART] button triggers different playing effects and techniques, separate from your keyboard playing. For example, pressing the [ART] button for a S.
Example 3 effects can also be used as those the same manner as Example 2. Holding an [ART] button (the button flashes in red) and playing/releasing a note enables you to add the articulation effect several times in succession. NOTE Keeping with the realistic response of the original instruments, the effects applied vary depending on the keyboard range you are playing in. When Super Articulation Voices are Selected for Multiple Parts When you select S.Art/S.
Controlling Multi Pad Playback Playing the Multi Pads 1 Press any of the MULTI PAD CONTROL [1]–[4] buttons to play a Multi Pad phrase. The corresponding phrase for the button starts playing back in its entirety at the currently set tempo. You can play up to four Multi Pads at the same time. 2 Press the [STOP] button to stop playback of the Multi Pad(s). If you want to stop a specific pad, simultaneously hold down the [STOP] button and press the pad(s) you wish to stop.
Using the Multi Pad Synchro Start Function You can also start Multi Pad playback by playing the keyboard or by starting Style playback. 1 2 While holding the MULTI PAD CONTROL [SELECT] button, press the desired button or buttons from [1]–[4]. NOTE The corresponding buttons flash in red, indicating standby status. To cancel the standby status of the selected Pad, carry out the same operation, or simply press the [STOP] button to cancel the status of all Pads. Start playback of the Multi Pad.
3 Operation Guide Singing with Song Playback— Setting Up This section explains how to set up for your singing performance with Songs, using Song selection and Vocal Harmony settings. As is the case in Chapter 1, the settings made in this section can be collectively stored in the Registration Memory as one song setting (page 96). Setting Up Song Playback Songs—MIDI Song and Audio Song For Genos2, “Song” refers to MIDI or audio data which include preset songs, commercially available music files, etc.
Switching Song playback modes Genos2 features two modes of Song playback: Dual Player mode and Song List mode. Dual Player mode plays back two Songs (SONG A and SONG B) simultaneously and lets you make a smooth, DJ-like transition between the two, using the special Cross Fader. Song List mode plays back Songs continuously along with a Song List previously made. 1 Press the [SONG] button to call up the Song Playback display. 2 Touch the display to switch the Song playback mode.
Selecting Songs (Dual Player mode) 1 Press the [SONG] button to call up the Song Playback display. Make sure that Dual Player mode is selected. 2 2 Touch the Song name in the Song A or Song B area. 3 Select the desired Song for each, A and B. NOTE For selecting from Audio Songs, touch [Audio]. For selecting from MIDI Songs, touch [MIDI]. • For basic operations of the Song Selection display, refer to “File Selection Display” (page 32).
Selecting Songs (Song List mode) 1 Press the [SONG] button to call up the Song Playback display. Make sure that Song List mode is selected. 2 2 Prepare a Song List When creating a new Song List 3 Touching (New) on the display allows you to create a new Song List. For details on how to edit the Song List, refer to the Reference Manual on the website.
Applying Effects to the Microphone Sound (Vocal Harmony) You can automatically apply various Vocal Harmony effects to your voice as you sing, or you can use Synth Vocoder to graft the unique characteristics of your voice onto synthesizer and other sounds. Using Vocal Harmony 1 NOTE Make sure to connect a microphone before using Vocal Harmony and Synth Vocoder. For instructions on connecting a microphone and making necessary settings, refer to page 110.
5 Follow the steps below, depending on which Type (and mode) you selected. If you selected the Chordal Type: 5-1 Make sure that the [ACMP] button is turned on. 5-2 Play back a Style while playing chords, or play back a Song which contains chords. Vocal harmonies based on the chords are applied to your singing. If you selected the Vocoder or Vocoder-Mono Type: 5-1 As necessary, change the “Keyboard” setting to “Off,” “Upper,” or “Lower.
4 Operation Guide Singing with Song Playback— Operations While Performing This section explains operations you can do during your singing performance with Songs: Song playback, displaying score and lyrics, adjusting the volume between two Songs, and switching microphone-related functions. Controlling Song Playback Song playback can be controlled by pressing buttons on the panel or from the Song playback display which is called up by pressing the [SONG] button.
Moving the Song Playback Position (Song Position pop-up window) When you press and hold the [PREV] or [NEXT] button, a setting display appears showing the current position of the Song. When the window is shown on the display, you can also use the Data dial to move backward/ forward continuously through the current file. The Phrase Mark number appears only when a MIDI Song containing Phrase Marks is selected.
Playback Operations exclusively for Audio Song Vocal Cancel This let you cancel or attenuate the center position of the stereo sound in Audio Song playback. This lets you sing “karaoke” style with just instrumental backing, or play the melody part on the keyboard, since the vocal sound is usually at the center of the stereo image in most recordings. To turn the Vocal Cancel function on/off, first select an Audio Song, then turn on/off (Vocal Cancel).
Using Song Position Markers (MIDI Song only) Song Position markers (SP1–SP4) can be placed in the MIDI Song data. This not only lets you navigate quickly and easily through the MIDI Song data, but also lets you set up convenient playback loops—allowing you to create dynamic Song arrangements “on the fly,” as you perform. Entering Song Position Markers Select the desired MIDI Song (page 78), and start playback (page 82). 2 Enter the Song Position markers.
Using Markers in loop playback In this section, we’ll explain loop playback by the example of looping between markers [1] and [2]. 1 Touch 2 After passing the [1] point, touch (Play/Pause) to start playback from the top of the Song. (Loop) to turn the loop function on. The Song plays back up to the [2] point, then goes back to [1] and loops between the two points.
Displaying Score, Lyrics, and Text files during Playback Displaying Music Notation (Score) of the MIDI Song You can view the music notation (score) of the selected MIDI Song. We suggest that you read through the music notation before starting to practice. 1 Select a MIDI Song (page 78). 2 Touch display. NOTE (Score) on the Song Playback display to call up the Score You can look through the entire notation by touching [L] or [R] when Song playback is stopped.
Displaying Lyrics of the MIDI Song When the selected Song contains lyric data, you can view it on the instrument’s display during playback. 1 Select a MIDI Song (page 78). 2 Touch display. (Lyrics) on the Song Playback display to call up the Lyrics When the Song data contains lyrics data, the lyrics are shown on the display. You can look through the entire lyrics by touching [L] or [R] when Song playback is stopped.
Adjusting the Volume Balance between SONG A and SONG B (Cross Fader) In the Dual Player mode of Song playback, the Cross Fader lets you adjust the volume balance between SONG A and SONG B playback. Moving the fader leftward increases the volume of SONG A playback, and moving rightward increases the volume of SONG B playback.
5 Operation Guide Adjusting the Parameters of Each Part—Mixer The Mixer gives you intuitive control over aspects of the keyboard parts and Song/Style channels, including volume balance and the timbre of the sounds. It lets you adjust the levels and stereo position (pan) of each Voice to set the optimum balance and stereo image, and lets you set how the effects are applied. This section covers the basic procedures for the Mixer. For details, refer to the Reference Manual on the website.
4 Set the value of each parameter. 5 Save your Mixer settings. NOTE To reset each parameter to the default value, touch the number value or setting and hold it. To save the Panel Mixer settings: Register them to Registration Memory (page 97). To save the Style Mixer Settings: Save them as a Style file to the User drive or USB flash drive. If you want to recall the settings for future use, select the Style file saved here. 5-1 Call up the operation display via [MENU] à [Style Creator].
Turning Each Channel of the Style or MIDI Song On/Off You can add variations and change the feeling of a Style or a MIDI Song by selectively turning channels on/off. Style Channels Each Style contains the channels listed below. • Rhythm 1/2: These are the basic parts of the Style, containing the drum and percussion rhythm patterns. • Bass: The bass part uses various appropriate instrument sounds to match the Style.
Changing the Voice for Each Channel of the Style or MIDI Song You can change the Voice for each channel via the Mixer display. 1 In the Mixer display, touch the [Style] tab or [Song] tab. 2 Touch the instrument icon below the channel name to call up the Voice Selection display, then select the desired Voice. Voice 3 As necessary, make other settings then save them as a Style file or Song file (step 5 on page 91).
6 Operation Guide Song Recording This instrument allows you to record your performance in two ways: MIDI recording and Audio recording. In addition, each way of recording features two different methods: Quick Recording, which is the easiest, most convenient way to record, and Multi Recording, which allows you to record each channel or each track independently. In this section, we’ll take a look at MIDI Quick Recording and Audio Quick Recording.
2 Start recording. 3 After you finish your performance, touch [Stop] to stop recording. 4 Touch [Save] to call up the Song Selection display, then save the recorded performance as a file (page 37). You can start recording by playing the keyboard, starting the Style, playing a Multi Pad or touching [Play/Pause]. NOTICE The recorded Song will be lost if you close the display or you turn the power off without executing the save operation.
7 Operation Guide Storing and Calling up Custom Panel Setups—Registration Memory, Playlist The Registration Memory function and the Playlist function allow you to save (or “register”) virtually all panel settings, and then instantly recall your custom panel settings for your performances by a simple, one-touch operation.
Saving and Recalling Custom Panel Setups with Registration Memory Registering Your Panel Setups 1 Make the desired panel Settings, such as those for Voices, Styles and Effects. 2 Press the [MEMORY] button in the REGISTRATION MEMORY section to call up the Registration Memory window. The list of items to be registered to Registration Memory Selecting the items to be registered The Registration Memory window contains the list for selecting the items to be registered.
Saving the Registration Memory as a Bank file You can save all ten registered panel setups as a Single Registration Memory Bank file. 1 Press the REGIST BANK [−] and [+] buttons simultaneously to call up the Registration Bank Selection display. 2 NOTE You can tag Registration Memory Bank files for easy search. For details, refer to the Reference Manual on the website. 2 Touch (File Edit) to call up the pop-up window, and then touch [Save] to save the Bank file.
Confirming the Registration Memory Bank Information You can call up the information display to confirm which Voices, Style and Songs are memorized to the [1]–[10] buttons of a Registration Memory Bank. 1 Call up the Registration Bank Selection display, then select the desired Bank. 2 Touch (Menu) then [Regist Bank Info] to call up the Regist Bank Information display. This display consists of two pages: Voice-related, and Style-related. You can switch between the two via [Voice]/[Style] on the display.
Managing a Large Repertoire by Using the Playlist The Playlist is useful for managing multiple set lists for your live performances. You can select only the desired files from a large repertoire (the huge number of the Registration Memory Bank files) and create a new set list for each performance. Adding Records to the Playlist By adding a Record to the Playlist, you can directly recall your desired Registration Memory. 1 Press the [PLAYLIST] button to call up the Playlist display.
[Select from Playlist Record] The display for selecting the Playlist Record is called up. 2-3 Touch the name “All Records” to call up the Playlist Selection display, select the Playlist file containing the desired Record, and then close the display. 2-4 Select the desired Playlist Record. 2-5 Touch [Add to Playlist] to close the display, and the new Playlist Record is added. 3 If necessary, edit the Playlist Record. The newly added Playlist Record simply recalls the selected registration Bank file.
Recalling custom panel setups via the Playlist 1 Press the [PLAYLIST] button to call up the Playlist display. 2 2 Touch the Playlist file name to call up the Playlist File Selection display. 3 Touch the desired Playlist file, and then close the display. 4 Touch the Record name on the Playlist display, and then touch [Load]. The Registration Memory Bank registered as the Playlist Record is recalled and the Action you’ve made is executed (page 100.
Copying the Playlist Records (Append Playlist) “Append Playlist” allows you to copy the existing Playlist file as a new Playlist file. 1 Press the [PLAYLIST] button to call up the Playlist display. 2 Touch [Add Record] on the display, and then touch [Add Playlist] in the pop-up window. 3 Touch the desired Playlist file to append. 4 Touch The Playlist File Selection display appears. All Records in the selected Playlist file are added at the bottom of the current Playlist.
8 Operation Guide Customizing for Optimum Performance You can customize the instrument for your own personal preferences and optimum performance. This section covers how to edit shortcuts on the Home display, set ASSIGNABLE buttons, make global settings, adjust the sound at the final output, and add expansion contents, such as Voices and Styles. Customizing the Shortcuts on the Home Display You can register an often used function to a shortcut on the Home display.
Making Global Settings (Utility) The Utility function provides a variety of convenient tools and settings for Genos2. These include general settings that affect the entire instrument, as well as detailed settings for specific functions. Also included are data reset functions and storage media control, such as disk formatting. Basic Procedure 1 Call up the operation display. 2 Touch the desired tab to call up the desired page, and change the settings or execute the operation.
Adjusting the Sound at the Final Output (Master Compressor, Master EQ) You can adjust the sound quality and the volume at the final output from Genos2 by making the Master Compressor and the Master EQ settings. 1 Call up the Mixer display via [MENU] à [Mixer]. 2 Touch the “Master” tab. 2 3 3 Touch a tab for editing the desired parameters.
Adding New Contents—Expansion Packs By installing Expansion Packs, you can add a variety of optional Voices and Styles to the “Expansion” folder in the User drive. The installed Voices and Styles can be selected via the User tab in the Voice or Style Selection displays, allowing you to expand your music performance and creation possibilities.
9 Operation Guide System Settings This section explains how to make important overall, system-related settings, including backup/restore of settings and file data. Confirming the Firmware Version and Hardware ID You can check the firmware version and hardware ID of this instrument. 1 Call up the operation display via [MENU] à [Utility]. 2 Touch [System]. The program version and the hardware ID are shown in the display.
Data Backup and Restore Data Backup You can back up all data in the User drive of this instrument (except for Expansion Voices/Styles) and all settings to the USB flash drive as a single file. This procedure is recommended for data security and backup in case of damage. 1 Connect the USB flash drive to the [USB TO DEVICE] terminal as backup destination. 2 Call up the display via [MENU] à [Utility] à [Factory Reset/ Backup] à page 2/2.
Connections—Using Your Instrument with Other Devices This chapter covers the connections of this instrument to other devices. To see where the connectors are located on the instrument, refer to pages 18 – 21. CAUTION Before connecting the instrument to other electronic components, turn off the power of all components. Also, before turning any components on or off, make sure to set all volume levels to minimum (0).
3 Connect a microphone to the [MIC INPUT] jack. For dynamic microphone connection, use the XLR connector or a standard 1/4" phone plug connector. For a condenser microphone, use the XLR connector. The combo jack accepts either XLR or 1/4" phone plug connectors. 4 When using a condenser microphone, turn the [+48V] switch on. 5 Return the [MASTER VOLUME] dial to the original level. NOTICE • Do not connect or disconnect any cables while turning on the [+48V] switch.
Disconnecting the microphone 1 Set the [MASTER VOLUME] knob and the [MIC GAIN] knob to the minimum position. 2 Set the [+48V] switch to off. 3 When using a condenser microphone, wait more than 10 seconds. 4 Disconnect the microphone from the [MIC INPUT] jack. NOTICE Disconnecting immediately can damage the condenser microphone and/or the instrument itself. Connecting the Optional Yamaha GNS-MS01 Speaker Use the [TO RIGHT SPEAKER], [TO LEFT SPEAKER] and [TO SUB WOOFER] jacks. Refer to page 124.
Using the LINE OUT SUB [3]–[4] jacks as AUX OUT jacks You can switch the function of the LINE OUT SUB [3]–[4] jacks to AUX OUT jacks from the instrument’s display called up via [MENU] à [Line Out]. For details, refer to the Reference Manual on the website. NOTICE Do not route the output from the AUX OUT jacks to the AUX IN jacks.
Connecting Footswitches/Foot Controllers (ASSIGNABLE FOOT PEDAL jacks) One or two optional Yamaha FC4A or FC5 Footswitches and an optional Yamaha FC7 Foot Controller can be connected to these ASSIGNABLE FOOT PEDAL jacks. A footswitch can be used for switching functions on and off, while a foot controller can be used to control continuous parameters, such as volume. FC7 FC5 NOTE Do not connect or disconnect any of the pedals when the power is on.
Connecting USB Devices ([USB TO DEVICE] terminal) You can connect a USB flash drive to the [USB TO DEVICE] terminal, and save data you’ve created on the instrument to the drive (page 37). Precautions when using the [USB TO DEVICE] terminal This instrument features a built-in [USB TO DEVICE] terminal. When connecting a USB device to the terminal, be sure to handle the USB device with care. Follow the important precautions below.
Formatting a USB flash drive or the internal User drive To format a USB flash drive or the internal User drive, execute the Format operation. In order to format a USB flash drive, make sure that a USB flash drive is properly connected to the [USB TO DEVICE] terminal beforehand. 1 Connect a USB flash drive for formatting to the [USB TO DEVICE] terminal. 2 Call up the operation display via [MENU] à [Utility] à [Storage]. NOTICE The Format operation deletes any previously existing data.
Connecting to a Computer ([USB TO HOST] terminal) By connecting a computer to the [USB TO HOST] terminal, you can transfer data between the instrument and the computer via MIDI, and transfer audio via the USB audio interface function. For details on using a computer with this instrument, refer to the “Computer-related Operations” on the website. NOTICE Use an AB type USB cable of less than 3 meters. USB 3.0 cables cannot be used.
Connecting to an Audio Player via Bluetooth communication Before using the Bluetooth function, be sure to read “About Bluetooth” on page 119. The playback sound of a Bluetooth-equipped device, such as a smartphone or portable audio player, can be sent to this instrument and heard through connected speakers or headphones. Bluetooth-equipped device: In this manual, “Bluetooth-equipped device” refers to a device that can transmit audio data to the instrument via Bluetooth wireless communication.
5 Play back audio data on the Bluetooth-equipped device to confirm that audio sound is output from the instrument. Once the device has been paired with the instrument, there is no need to perform pairing again. When you turn on the instrument the next time, the last-connected Bluetooth-equipped device will be connected to this instrument automatically, if the Bluetooth function of the Bluetooth-equipped device and the instrument is set to on.
Viewing the Instrument’s Display on an External Monitor By connecting with an external monitor such as a television via the HDMI terminal, you can separately show the lyrics/text or duplicate the instrument display (mirroring) on an external monitor. NOTICE When connecting to an external monitor, use a certified HDMI cable. External monitor HDMI cable Set the display content that is to be output via [MENU] à [Utility] à [Speaker/Connectivity]. Content Determines what is output to external monitor.
MEMO Connections—Using Your Instrument with Other Devices 121 Genos2 Owner’s Manual
Function List This section simply and very briefly explains what you can do in the displays called up by pressing the buttons on the panel, or by touching each icon on the Menu display. For more information, refer to the page indicated below or the Reference manual on the website. The “l” mark indicates that the detailed information is described in the Reference Manual.
Menu Description Pages Reference Manual Makes settings for the microphone sound. 111 l Vocal Harmony For adding Vocal Harmony effects to your singing. You can edit the Vocal Harmony and save as your original harmony. 80 l Regist Sequence Determines the order for calling up Registration Memory settings when using the pedal. - l Regist Freeze Determines the item(s) that remain unchanged even when you call up panel setups from the Registration Memory.
Appendix Installing the Optional Speakers NOTICE Make sure that all of the parts below have been included in the GNS-MS01 speaker package. Satellite speakers (2) Subwoofer speaker (1) Speaker brackets (2) Phone cables (2) Use only the supplied cables. 8-pin mini DIN cable (1) AC power cord (1) 1 Turn Genos2’s power off, and disconnect the AC power cord. Also, make sure to disconnect the keyboard from any other external devices. 2 Insert the two speaker brackets to the rear panel of Genos2.
4 Use the phone cables to connect the speakers to the respective outputs on Genos2. Either cable can be used interchangeably with either output jack. 5 Use the 8-pin mini DIN cable to connect the subwoofer to Genos2. Genos2 Subwoofer 6 Connect the supplied AC power cord to the subwoofer. 7 Connect the power plugs of Genos2 and the subwoofer to an appropriate AC outlet. 8 Set the volume controls (MASTER VOLUME on Genos2 and MAIN VOLUME on the subwoofer) to minimum.
Direct Access Chart Press the [DIRECT ACCESS] button, then press one of the buttons (or move the appropriate knob, slider, joystick or pedal) listed below to call up the desired display.
Function of the accessed LCD display Operation: [DIRECT ACCESS] button + button listed below SLIDER Display Level Cursor TAB PAGE/POP UP Cursor Position 1 Slider 1 2 Slider 2 3 Slider 3 4 Slider 4 5 6 Menu Live Control Knob/Slider Slider 5 - Slider 6 7 Slider 7 8 Slider 8 9 Slider 9 ASSIGN - 1 ONE TOUCH SETTING 2 - - Style Information - MULTI PAD SELECT - - Multi Pad Edit Multi Pad 1 STOP Audio Link Multi Pad - - - 3 (Style Selection) 4 MULTI PAD 1 2 Multi
Function of the accessed LCD display Operation: [DIRECT ACCESS] button + button listed below Display Level Cursor TAB PAGE/POP UP Cursor Position REGIST BANK + - - REGIST BANK − - - FREEZE Registration Freeze - - - MEMORY Registration Sequence - - - Regist Bank Edit - 1 2 REGIST 3 4 Regist Bank Information: Voice page (Regist Bank Selection) 5 - 6 - 7 Regist Bank Information: Style page 8 9 10 ASSIGNABLE FOOT PEDAL 1 2 Pedal 1 Menu Assignable - - 3 *1: When the Organ
Troubleshooting Overall A click or pop is heard when the power is turned on or off. This is normal. Electrical current is being applied to the instrument. The power is automatically turned off. This is normal and due to the Auto Power Off function. If necessary, set the parameter of the Auto Power Off function (page 24). Noise is heard from the instrument. Noise may be heard if a mobile phone is used near the instrument or if the phone is ringing.
Style The Style does not start even when the [START/STOP] button is pressed. The Rhythm channel of the selected Style may not contain any data. Turn the [ACMP] button on and play the left-hand section on the keyboard to sound the accompaniment part of the Style. Only the rhythm channel plays. Make sure the Auto Accompaniment function is turned on; press the [ACMP] button. Make sure to play keys in the chord range of the keyboard. Styles in a USB flash drive cannot be selected.
In the Audio Recording function, an error message appears and audio cannot be recorded to the internal User drive. The data on the User drive is fragmented and cannot be used as is. Since there is no defragmentation function in the Audio Recording, the drive can only be defragmented by formatting it. To do this, first back up the data by using the data backup function (page 109), then format the drive, and finally restore the backup data.
Specifications Product Name Size/Weight Digital Keyboard Dimensions (W × D × H) Weight 14.2 kg (31 lb, 5 oz) Number of keys Keyboard Type Touch Response Joystick Other Controllers Control Interface Main Display Sliders 9 (Assignable, with LED gauge), Cross Fader 9 (A–F, 1–3) Articulation buttons ART. 1, ART. 2, ART.
Recording Data Capacity Playback Songs (Audio) Format Recording Recording (Multi) .aud (Genos original: 44.
Included Accessories • Owner’s Manual • AC power cord • Music Rest, two Music Rest brackets Separately Sold Accessories (May not be available depending on your area.) • • • • • • Option Speaker: GNS-MS01 Headphones: HPH-50, HPH-100, HPH-150 Footswitch: FC4A, FC5 Foot Controller: FC7 Wireless MIDI Adaptor: MD-BT01 Keyboard Stand: L-7B The contents of this manual apply to the latest specifications as of the publishing date.
MEMO Appendix Genos2 Owner’s Manual 135
Index A A-B Repeat.............................................................................................. 84 Accessories................................................................................................9 Accompaniment................................................................................... 44 AC IN......................................................................................................... 23 Action (Playlist)........................................................
Master EQ..............................................................................................106 Menu................................................................................................ 33, 122 Metronome.............................................................................................41 Mic Effect..................................................................................................16 Microphone......................................................................
Note on source code distribution For three years after the final factory shipment, you may request from Yamaha the source code for any portions of the product which are licensed under the GNU General Public License or GNU Lesser General Public License by writing to one of the Yamaha office addresses listed at the end of this Owner’s Manual. The source code will be provided at no charge; however, we may require you to reimburse Yamaha for the cost of delivering the source code to you.
For European Union and United Kingdom SIMPLIFIED EU DECLARATION OF CONFORMITY / SIMPLIFIED UK DECLARATION OF CONFORMITY Hereby, Yamaha Corporation declares that the radio equipment type [Genos2] is in compliance with Directive 2014/53/EU and the radio equipment regulations of UK. The full texts of the EU declaration of conformity and the UK declaration of conformity are available at the following internet address: https://europe.yamaha.com/en/support/compliance/doc.
Genos2 Owner’s Manual
Important Notice: U.S. LIMITED WARRANTY for Customers in the United States For detailed information about this Yamaha product and warranty service, please either visit the following website address (printable file is available at our website) or contact Customer Service at the address or telephone number identified below. Website Address: https://yamaha.
Yamaha Worldwide Representative Offices English For details on the product(s), contact your nearest Yamaha representative or the authorized distributor, found by accessing the 2D barcode below. Deutsch Wenden Sie sich für nähere Informationen zu Produkten an eine Yamaha-Vertretung oder einen autorisierten Händler in Ihrer Nähe. Diese finden Sie mithilfe des unten abgebildeten 2D-Strichodes.
Yamaha Global Site https://www.yamaha.com/ Yamaha Downloads https://download.yamaha.
