Owner’s Manual Before using the instrument, be sure to read “PRECAUTIONS” on page 5. v2.
SPECIAL MESSAGE SECTION PRODUCT SAFETY MARKINGS: Yamaha electronic products may have either labels similar to the graphics shown below or molded/stamped facsimiles of these graphics on the enclosure. The explanation of these graphics appears on this page. Please observe all cautions indicated on this page and those indicated in the safety instruction section. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK).
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING Please keep this manual in a safe and handy place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, shortcircuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Power supply/Power cord Water warning • Do not place the power cord near heat sources such as heaters or radiators.
Notices and Information NOTICE To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below. Handling • Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio may generate noise.
Information About copyrights • Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal use. • This product incorporates and bundles contents in which Yamaha owns copyrights or with respect to which Yamaha has license to use others’ copyrights.
Copyright Notice The followings are the titles, credits and copyright notices for the songs pre-installed in this instrument. Eye Of The Tiger Theme from ROCKY III Words and Music by Frank Sullivan and Jim Peterik Copyright (c) 1982 Sony/ATV Music Publishing LLC, Rude Music, Three Wise Boys LLC, WB Music Corp.
Congratulations! Included Accessories You are the proud owner of an extraordinary electronic keyboard. In addition to its stylish curved design, the Yamaha Genos combines the most advanced tone generation technology with state-of-the-art digital electronics to give you stunning sound with maximum musical versatility—a beautiful instrument from every perspective.
About the Manuals This instrument has the following documents and instructional materials. Included Documents Owner’s Manual (this book) Provides overall explanations of Genos basic functions. Online Materials (Downloadable from the web) Reference Manual (only in English, French, German, Italian, Dutch, and Polish) Explains advanced features of the instrument, such as creating original Styles, Songs and Multi Pads, and making the settings of specific parameters.
Main Features Replacing the hugely successful Tyros, Genos is the new benchmark in Digital Workstation sound, design and user experience. Whether you’re a professional musician or a hobbyist, Genos will inspire and intensify your musical performance and enjoyment. Extraordinarily expressive and realistic Voices Main Features The sonic quality of every Voice in Genos is beyond any other Digital Workstation you’ve ever played—this instrument is quite simply a game changer.
Contents PRECAUTIONS ....................................................................................................................................... 5 Included Accessories ............................................................................................................................... 9 About the Manuals ................................................................................................................................. 10 Main Features .....................................
Operation Guide 4 Singing with Song Playback—Operations While Performing 78 Controlling Song Playback..................................................................................................................... 78 Using Song Position Markers (MIDI Song only)..................................................................................... 81 Displaying Score, Lyrics, and Text files during Playback.......................................................................
Using Genos—A Broad Overview This section provides a helpful overview of the wide range of functions available in Genos, and places you can find necessary information on those topics. If you need help in understanding a feature, function or operation— or need to have a general understanding of what Genos can do and how to effectively use it—look through this section. OM * : Genos Owner’s Manual (this book). The relevant chapter names are shown after this symbol.
Using Genos with a computer Connecting a computer to the instrument OM Connections Transferring files (Songs, Styles, Backup files, etc) Computer Related Operations (*) Using Genos—A Broad Overview Playing back Songs on a computer via the instrument sounds Recording your keyboard performance to a computer Obtaining the Expansion Packs made by Yamaha (also called “Premium Packs”) Yamaha MusicSoft website https://www.yamahamusicsoft.
Main Functions This section briefly explains the main functions of Genos, to help you better understand the overall capabilities of the instrument. Styles—Rhythm and Auto Accompaniment— Genos features a variety of accompaniment and rhythmic backing patterns (called “Styles”) in a variety of different musical genres including pop, jazz, and many others. Styles feature sophisticated Auto Accompaniment patterns, letting you produce automatic accompaniment playback simply by playing chords with your left hand.
Registration Memory—Saving and recalling custom panel setups— The Registration Memory function allows you to save (or “register”) virtually all panel settings to a Registration Memory button, and then instantly recall your custom panel settings by simply pressing a single button. The registered settings for ten Registration Memory buttons are saved as a single Registration Bank (file).
Panel Controls and Terminals Top Panel !6 r e w q !0 t !1 y u !4 !3 !2 !5 @0 i o q [ ] (Standby/On) switch................................. Page 23 Turns on the instrument’s power or sets to standby. o [PHONES] jack................................................ Page 22 For connecting a pair of headphones. w [MASTER VOLUME] dial .............................Page 23 Adjusts the overall volume. !0 Cross Fader ......................................................
!8 Panel Controls and Terminals !7 @8 @6 @7 !9 @4 @1 @2 @3 @5 !7 Touch LCD and related controls .................... Page 30 !8 Gateway buttons............................................... Page 28 For calling up the Home display and other particular displays directly. !9 ASSIGNABLE buttons .................................. Page 100 For assigning shortcuts to often used functions. @0 DIRECT ACCESS button .....................
Rear Panel and Bottom @9 #0 @9 #1 #3 #2 #4 #5 $3 @9 Slots ......................................................... Pages 20, 118 The four slots nearest the display panel are for connecting the music rest brackets; the other slots are for connecting the speaker brackets of the optional GNS-MS01 speakers. #0 [TO RIGHT SPEAKER] jack....................... Page 118 For connecting an optional set of speakers. #1 [TO SUB WOOFER] terminal......................
@9 #7 #6 #8 NOTICE When using phantom power, observe the following to prevent noise and possible damage to Genos or connected equipment. • Do not connect or disconnect any devices while the phantom power switch is ON. • Set all output level controls to the minimum before turning the phantom power switch to ON or OFF. • When connecting a device not requiring phantom power to the MIC INPUT jack, make sure to turn the phantom power switch to OFF.
Starting Up Audio Connections Connecting headphones or a speaker system Since the instrument has no built-in speakers, you’ll need to use external equipment, such as headphones or a speaker system, to hear the sound of the instrument. Using headphones Connect a set of headphones to the [PHONES] jack. Using a speaker system CAUTION For instructions on installing the optional speakers GNS-MS01, refer to page 118. For instructions on connecting other speakers, refer to page 108.
Power Supply 1 Connect the supplied power cord to the [AC IN] jack on the instrument’s rear panel. WARNING Use only the supplied power cord. CAUTION 2 Connect the other end of the power cord to an AC outlet. Starting Up When setting up the product, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet.
Auto Power Off and Auto Power Saving functions To prevent unnecessary power consumption, this instrument features an Auto Power Off function that automatically turns the power off if the instrument is not operated for a specified period of time. The amount of time that elapses before the power is automatically turned off is approximately 30 minutes by default; however, you can change the setting (page 25).
Auto Power Saving Lets you set the amount of time that elapses before the Auto Power Saving function decreases brightness of the LIVE CONTROL view. Touch this to call up the list of settings, then select the desired one. To disable Auto Power Saving, select “Disabled” here. Auto Power Off Lets you set the amount of time that elapses before the power is turned off by the Auto Power Off function (page 24). Touch this to call up the list of settings, then select the desired one.
Display Structure Genos has two displays (the LCD Touch Screen and the LIVE CONTROL view) and lighting buttons for visually helping you to understand the current status. LIVE CONTROL view (Sub Display) LCD (Main Display; touch screen) The LIVE CONTROL view indicates the parameters operated when you use the six LIVE CONTROL knobs and nine LIVE CONTROL sliders. For details on the display structure, see page 27. The LCD indicates the parameters and values related to the currently selected operation.
LIVE CONTROL View (Sub Display) Structure In the LIVE CONTROL view, you can see the parameters status controlled by the LIVE CONTROL knobs and the LIVE CONTROL sliders. There are two displays: knobs and sliders, and you can switch between these two displays while operating the instrument. To switch between the displays without changing parameter values, simply press the [KNOB ASSIGN]/[SLIDER ASSIGN] buttons.
Main Display Structure—Using the Gateway Buttons The Gateway buttons are just as their name suggests—a convenient, easy-to-understand “gateway” to Genos. When the instrument is turned on, the Home display is called up. However, as you operate the instrument, you can directly call up the Home display and other desired displays directly by pressing the Gateway buttons on the front panel. Other functions and various detailed settings for the instrument can be accessed from the Menu display.
Display Structure Menu display By touching each of the icons, you can call up various functions, such as Song Score, Volume Balance and other detailed settings. (page 33) Voice Part Setup display This is for making detailed settings such as Voice Edit and Effect settings of the keyboard parts. For details on the Voice Part Setup display, refer to the Reference Manual on the website. Playlist display This is for selecting and editing Playlists (page 96.
Basic Operations Display Configuration This section covers the most often used displays: Home, File Selection and Menu. The Home display appears when the power is turned on. The term “File Selection display” refers to all the various displays called up on the instrument from which you can select files. The Menu display is a portal display for various functions and can be called up by pressing the [MENU] button.
Information area in the Home display q r w t y e u Basic Operations q Bar/Beat/Tempo Displays the current position (bar/beat/tempo) in Style playback or MIDI Song playback. By rotating the Data dial, you can call up the Tempo pop-up display and adjust the tempo. w Upper Octave/Transpose Displays the amount that the upper octave value is shifted, and the amount of master transposition in semitone units (page 61). e Clock The current time is shown here.
File Selection Display The File Selection display is for selecting a Voice, Style, Song, Multi Pads and other items. You can call up this display by touching the name of the Voice, Style or Song on the Home display, or by pressing one of the VOICE SELECT buttons or [STYLE] button, etc. The displays are different, depending on which file type is selected. For example, when Voice is selected, the Voice Selection display is called up.
Menu Display This is the portal display for using various functions and can be called up by pressing the [MENU] button. Basic Operations Various convenient functions are shown via icons. Touching each of them calls up the corresponding function. This list consists of two pages, which you can select by touching [Menu 1] or [Menu 2]. For brief information on each function, refer to the “Function List” (page 116). NOTE You can also change pages by flicking horizontally.
Display-based Controls The display of this instrument is a special touch screen that allows you to select or change the desired parameter by simply touching the corresponding setting on the display. You can also decrease/increase the value in small steps by rotating the Data dial or pressing the [DEC]/[INC] button. Using the display (touch screen) NOTICE Do not use any sharp or hard tools to operate the touch screen. Doing so may damage the display.
Using the Data dial, [ENTER] button, and [DEC]/[INC] buttons Depending on the display, the Data dial and the buttons can be used in the following two ways. Adjusting the parameter values After selecting the desired parameter, use the Data dial or the [DEC]/[INC] buttons to adjust the value. This is useful if you have difficulty adjusting by touching on the display, or want finer control over the adjustment.
Calling up the Desired Display Instantly—Direct Access With the convenient Direct Access function, you can instantly call up the desired display—with just a single additional button press. Refer to the “Direct Access Chart” on page 120 for a list of the displays that can be called up with the Direct Access function. 1 Press the [DIRECT ACCESS] button. A message appears in the display prompting you to press the appropriate button.
File Management Data you have created such as recorded Song and edited Voice can be saved as files to the instrument (referred to as “User drive”) and a USB flash drive. If you’ve saved a lot of files, you may have trouble finding the desired file quickly. To make operation easier, you can organize your files in folders, rename the files, delete unnecessary files, etc. These operations are done in the File Selection display.
6 Touch [OK] in the Character Entry window to actually save the file. The saved file will be automatically located at the appropriate position among the files in alphabetical order. Creating a new folder Folders can be created, named and organized as desired, making it easier to find and select your original data. 1 In the File Selection display, touch the User tab (page 32) then select the location to which you want to create a new folder. To show the next higher level folder, touch (Up).
4 Select the desired files/folders by touching each item. One or more files/folders can be selected (highlighted). To cancel the selection, touch the same item again. Touch [Select All] to select all items indicated on the current display including the other pages. To cancel the selection, touch [All Off]. Touch [Copy] or [Move] at the top of the display, to call up the display for selecting the destination. 6 Select the desired destination (path) to paste the files/folders.
Entering Characters This section covers how to enter characters for naming your files/folders, inputting keywords on searching file, etc. Entering characters is done in the display shown below. 2, 3 1 1 Touch the character type. Touching [Symbol] (or [abc]) switches between entering symbols or Roman letters (and numbers). To switch between entering capital letters or small letters, touch (Shift).
Locking the Panel Settings (Panel Lock) When the panel settings are locked, nothing happens if you press any panel buttons. For example, when you take a break during your performance and leave the instrument unattended, this feature protects the panel settings from being accessed by others. 1 Call up the Panel Lock display via [MENU] [Panel Lock]. The numeric keypad for PIN code entry is called up.
Quick Guide—For Performing on Genos Manual panel settings and performing a single song Playing the keyboard with Styles (Auto Accompaniment) Optimum panel settings for the current Style (One Touch Setting) ... p. 47 Setting up the Style Calling up the most appropriate panel settings (Keyboard Parts, Harmony/Arpeggio, or Multi Pads) for the selected Style. or ... p. 44 Setting up the Voices ... p. 48 (Setting up keyboard parts) Setting up Harmony/ Arpeggio ... p.
Setting up Vocal Harmony ... p. 76 Quick Guide—For Performing on Genos Assigning functions to controllers ... p. 62 Playing with Styles Operations during performance: p. 64 Setting up Multi Pads ... p. 59 Assigning functions to controllers ... p. 62 Setting up Vocal Harmony ... p. 76 Singing with Song playback Operations during performance: p. 78 Registering the Registration Memory in a Playlist ... p. 96 Editing the Playlist for your live performance set list ... p.
1 Operation Guide Playing with Styles—Setups This section gives you basic steps on how to enhance your keyboard performance with Styles (Rhythm and Auto Accompaniment). Go through the various instructions below to completely set up your performance of a single song: Style, Keyboard Part (Voice), Multi Pad, and various types of controllers. The settings made in this section can be collectively stored in the Registration Memory as one song setting (page 92).
Style Characteristics The particular type of Style is indicated the upper left of the Style name in the Style Selection display. The defining characteristics of these Styles and their performance advantages are described below. 1 Playing with Styles—Setups • Session: These Styles provide even greater realism and authentic backing by mixing in original chord types and changes, as well as special riffs with chord changes, with the Main sections.
Adjusting the tempo The TEMPO [-] and [+] buttons let you change the playback tempo of the Metronome, Style and MIDI Song. The tempo of the Style and MIDI Song can also be adjusted via the [TAP TEMPO] button. NOTE If you want to adjust the tempo of an Audio Song, use the Time Stretch function on page 80. TEMPO [-]/[+] buttons Press the TEMPO [-] or [+] button to call up the Tempo pop-up display. Use the TEMPO [-]/[+] buttons to decrease or increase the tempo over a range of 5–500 beats per minute.
Optimum Panel Settings for the Current Style (One Touch Setting) One Touch Setting is a powerful and convenient feature that automatically calls up the most appropriate panel settings (Voices, effects, etc.) for the currently selected Style, with the touch of a single button. If you’ve already decided which Style you wish to use, you can have One Touch Setting automatically select the appropriate Voice for you. 1 Select the Desired Style (steps 1–2 on page 44).
Setting up Keyboard Parts There are four keyboard parts for your manual performance: LEFT, RIGHT 1, RIGHT 2 and RIGHT 3, and each part has one Voice. You can combine these parts by using the PART ON/OFF buttons to create luscious instrument textures and convenient performance combinations.
Holding the LEFT part Voice (Left Hold) By turning on the PART ON/OFF [LEFT HOLD] button when the LEFT part is ON, the LEFT part Voice is held even when the keys are released. Non-decaying Voices such as strings are held continuously, while decay-type Voices such as piano decay more slowly (as if the sustain pedal has been pressed). This function is convenient when used along with Style playback since the sound of the chords matching Style playback are maintained.
q Split Point (Style + Left) Sets Split Point (Style) and Split Point (Left) to the same note. In this case, the Chord Section and the LEFT part section occupy the same area. Specify the Split Point directly from the keyboard by simultaneously holding [Style + Left] on the display and pressing the desired key on the keyboard. Split Point (Style + Left) Chord + LEFT part section (Left-hand section) w Split Point (Style, Left, Right 3) Right-hand section Sets each Split Point individually.
Specifying chords with your right hand for Style playback By changing the Chord Detection area from the left-hand section to the right-hand section, you can play a bass line with your left hand while using your right hand to play chords for controlling Style playback. 1 Call up the Split Point/Fingering window. [MENU] [Split & Fingering] 2 Make the necessary settings by touching the display. 1 Playing with Styles—Setups Chord Detection Area Select “Upper.
Selecting a Voice for Each Keyboard Part 1 Press the VOICE SELECT button corresponding to the desired part. The Voice Selection display (for the desired part) appears. 2 Touch the desired Voice. To hear the characteristics of the Voices: Touch (Demo) to start demo playback of the selected Voice. Touch (Demo) again to stop playback. 3 NOTE You can also call up the Voice Selection display via the Home display (page 30) or the Voice Part Setup display (Reference Manual on the web site).
Creating Original Organ Flutes Voices Genos uses advanced digital technology to recreate the legendary sound of vintage organs. Just as on a traditional electronic organ, you can create your own sound by increasing and decreasing the levels of the flute footages. The created Voice can be saved for future recall. 1 On the Voice Selection display, select the desired Organ Flutes Voice.
Using Ensemble Voices These are special settings of the keyboard parts that feature multiple Voices, used in realistic ensemble combinations, such as brass section and string quartet. Up to four special parts or instruments are provided within a single Voice. But rather than just being a combination, the parts are dynamically assigned to the notes, and are distributed among the intervals you play in exceptionally natural, musical ways—as if four different players were actually playing the parts live.
To return to the Home display Press the [EXIT] button or the [HOME] button. The Voice area shows the Ensemble Voice name. To call up the Voice Selection display again to select other presets, touch the Voice area of the Home display. 1 Playing with Styles—Setups Exiting from the Ensemble Voice mode 1 Press any one of the VOICE SELECT buttons to call up the Voice Selection display. 2 Select a Voice other than an Ensemble Voice.
Setting up Keyboard Harmony/Arpeggio You can apply the Keyboard Harmony or Arpeggio features to enhance or change the sound of the Right-hand parts (RIGHT 1–3). Keyboard Harmony applies performance effects such as harmony (duet, trio, etc.), echo, tremolo and trill to the notes played in the Right-hand section. The Arpeggio function lets you play arpeggios (broken chords) by simply pressing the notes of the chord.
• When the [ACMP] button is off and the LEFT part is on: Split Point (Left) RIGHT 1–3 parts LEFT part and chord section for Harmony effect • When both the [ACMP] button and the LEFT part are on: Split Point (Style) Split Point (Left) Playing with Styles—Setups LEFT part 1 RIGHT 1–3 parts Chord section for Style playback and Harmony effect Multi Assign The Multi Assign effect automatically assigns the notes of chords you play on the righthand section of the keyboard to separate parts (Voices).
5 Play a note or notes to trigger the Arpeggio. The arpeggiated phrase differs depending on the notes played. To turn off the effect, turn the [HARMONY/ARPEGGIO] button off. 58 Genos Owner’s Manual NOTE • By using the Arpeggio Quantize function, Arpeggio playback can be synchronized with Song/Style playback, allowing any slight imperfections in the timing to be corrected. This can be set in the display: [MENU] [VoiceSetting] [S.Art2/Arpeggio].
Setting up Multi Pads Selecting Multi Pads 1 Press the MULTI PAD CONTROL [SELECT] button to call up the Multi Pad Bank Selection display. NOTE You can also call up the Multi Pad Selection display via the Home display (page 30). 1 3 Touch the desired Multi Pad Bank. If necessary, try out the selected Multi Pad(s). Playing with Styles—Setups 2 NOTE For basic operations of the Multi Pad Selection display, refer to “File Selection Display” (page 32).
Memorizing Original Panel Settings to One Touch Setting You can memorize your original panel settings (mainly Style, Voices, and Multi Pads) to a One Touch Setting (OTS). The newly created One Touch Setting will be saved in the User drive or a USB flash drive as a Style, and you can call up the One Touch Setting as a part of the Style. 1 Select the desired Style to memorize your One Touch Setting. 2 Make the desired panel settings, such as those for Voices and Effects.
Changing the Pitch of the Keyboard Transposing the pitch in semitones (TRANSPOSE [-]/[+]buttons) The TRANSPOSE [-]/[+] buttons transpose the overall pitch of the instrument (the keyboard sound, Style playback, MIDI Song playback, and so on) in semitone steps (from -12 to 12). To instantly reset the transpose value to 0, press the [-] and [+] buttons simultaneously. Master Transposes the pitch of the entire sound, with the exception of the Audio Song and input sound from a microphone or the AUX IN jacks.
Setting up Assignable Controllers You can assign parameters and functions to the LIVE CONTROL knobs/sliders, the [ROTARY SP/ASSIGNABLE] button, or optional footswitches for quick operations and expressive control during your keyboard performance. The setup of assignable controllers is stored/recalled from the registration memory so you can change them all together.
Assigning functions to the [ROTARY SP/ASSIGNABLE] button Various functions can be assigned to the [ROTARY SP/ASSIGNABLE] button. 1 To call up the Edit display, touch [MENU] [Assignable]. 1 2 Playing with Styles—Setups 2 Double-tap (touch twice) the “Rotary Sp/Assignable” item on the display. The function selection pop-up window appears. 3 Touch the desired function. NOTE For details on assignable parameters and functions, refer to the Reference Manual on the website.
2 Operation Guide Playing with Styles—Operations While Performing If you’ve made all desired settings for a single song (in the previous sections), now you’re ready to play the keyboard. This section mainly explains the various Style-related operations you’ll use during your keyboard performance: Style playback, applying expressive effects, and Multi Pad playback. Operating Style Playback Starting and stopping Style playback [START/STOP] button Starts playback of the rhythm part of the current Style.
Fading In/Out The Fade In/Out function produces smooth fade-ins and fade-outs when starting/stopping the playback of a Style or Song. You can assign this function to the [ROTARY SP./ASSIGNABLE] button, footswitches, or the ASSIGNABLE [A]–[F] buttons. NOTE For information on assigning functions to each controller, refer to “Setting up Assignable Controllers” (page 62) and “Setting the Functions or Shortcuts to the ASSIGNABLE Buttons” (page 100).
[BREAK] button This lets you add dynamic breaks in the rhythm of the accompaniment. Press the [BREAK] button during Style playback. When the one-measure Break pattern finishes playing, Style playback automatically shifts to the Main section. About the lamp status of the section buttons (INTRO/MAIN VARIATION/BREAK/ENDING) • Red: The section is currently selected. • Red (flashing): The section will be played next, following the currently selected section.
Holding the Modulation value (MODULATION HOLD) The Joystick is self-centering when released. However, you can hold the current Modulation value by pressing the [MODULATION HOLD] button. • If the [MODULATION HOLD] button is turned on while the Joystick is moved, the Modulation value (Y-axis value) is fixed and held even after the Joystick is released. • If the [MODULATION HOLD] button is turned off, the Modulation value returns to the default value for the Voice of each Part.
S.Art2 Voices NOTE Some of the wind instrument and strings Voices feature a special technology called AEM, which utilizes detailed samples of special expressive techniques used on those specific instruments—to bend or slide into notes, to “join” different notes together, or to add expressive nuances at the end of a note, etc. You can add these articulations by playing legato or non-legato, or jumping between notes in octave intervals or greater.
Example 3 When an S.Art2 Voice is selected, pressing the available [ART] button and playing/releasing a note enables you to add articulation effects, such as bend up/down, glissando up/down, brass fall, etc. When you press the available [ART] button, it will flash in red until the effect is finished playing. You can cancel by pressing the button again while it flashes. Immediately after you press/release the note and articulation effect sounds, the button lights in red.
Controlling Multi Pad Playback Playing the Multi Pads 1 Press any of the MULTI PAD CONTROL [1]–[4] buttons to play a Multi Pad phrase. The corresponding phrase for the button starts playing back in its entirety at the currently set tempo. You can play up to four Multi Pads at the same time. 2 Press the [STOP] button to stop playback of the Multi Pad(s). If you want to stop a specific pad, simultaneously hold down the [STOP] button and press the pad(s) you wish to stop.
Using the Multi Pad Synchro Start Function You can also start Multi Pad playback by playing the keyboard or by starting Style playback. 1 While holding the MULTI PAD CONTROL [SELECT] button, press the desired button or buttons from [1]–[4]. The corresponding buttons flash in red, indicating standby status. To cancel the standby status of the selected Pad, carry out the same operation, or simply press the [STOP] button to cancel the status of all Pads. 2 Start playback of the Multi Pad.
3 Operation Guide Singing with Song Playback—Setting Up This section explains how to set up for your singing performance with Songs, using Song selection and Vocal Harmony settings. As is the case in Chapter 1, the settings made in this section can be collectively stored in the Registration Memory as one song setting (page 92). Setting Up Song Playback Songs—MIDI Song and Audio Song For Genos, “Song” refers to MIDI or audio data which include preset songs, commercially available music files, etc.
Song File Compatibility You can play back the following types of Songs. • Preset Songs (MIDI Songs) • Your own recorded Songs (for instructions on recording, see page 90) • Commercially available Songs: MIDI files in SMF (Standard MIDI File) format, Audio files in WAV or MP3 format. WAV ....... 44.1 kHz sample rate, 16 bit resolution, stereo MP3 ....... MPEG-1 Audio Layer-3: 44.
Selecting Songs (Dual Player mode) 1 Press the [SONG] button to call up the Song Playback display. Make sure that Dual Player mode is selected. 2 2 Touch the Song name in the Song A or Song B area. The Song Selection display appears. 3 Select the desired Song for each, A and B. NOTE For selecting from Audio Songs, touch [Audio]. For selecting from MIDI Songs, touch [MIDI].
Selecting Songs (Song List mode) 1 Press the [SONG] button to call up the Song Playback display. Make sure that Song List mode is selected. 2 2 Prepare a Song List When creating a new Song List 3 Singing with Song Playback—Setting Up Touching (New) on the display allows you to create a new Song List. For details on how to edit the Song List, refer to the Reference Manual on the website.
Applying Effects to the Microphone Sound (Vocal Harmony) You can automatically apply various Vocal Harmony effects to your voice as you sing, or you can use Synth Vocoder to graft the unique characteristics of your voice onto synthesizer and other sounds. NOTE Make sure to connect a microphone before using Vocal Harmony and Synth Vocoder. For instructions on connecting a microphone and making necessary settings, refer to page 106.
5 Follow the steps below, depending on which Type (and mode) you selected. If you selected the Chordal Type: 5-1 Make sure that the [ACMP] button is turned on. 5-2 Play back a Style while playing chords, or play back a Song which contains chords. Vocal harmonies based on the chords are applied to your singing. If you selected the Vocoder or Vocoder-Mono Type: 5-1 As necessary, change the “Keyboard” setting to “Off,” “Upper,” or “Lower.
4 Operation Guide Singing with Song Playback—Operations While Performing This section explains operations you can do during your singing performance with Songs: Song playback, displaying score and lyrics, adjusting the volume between two Songs, and switching microphone-related functions. Controlling Song Playback Song playback can be controlled by pressing buttons on the panel or from the Song playback display which is called up by pressing the [SONG] button.
Moving the Song Playback Position (Song Position pop-up window) When you press and hold the [PREV] or [NEXT] button, a setting disFor Audio Songs play appears showing the current position of the Song. When the window is shown on the display, you can also use the Data dial to move backward/forward continuously through the current file. The Phrase Mark number appears only when a MIDI Song containing For MIDI Songs Phrase Marks is selected.
Playback Operations exclusively for Audio Song Vocal Cancel NOTE This let you cancel or attenuate the center position of the stereo sound in Audio Song playback. This lets you sing “karaoke” style with just instrumental backing, or play the melody part on the keyboard, since the vocal sound is usually at the center of the stereo image in most recordings. To turn the Vocal Cancel function on/off, first select an Audio Song, then turn on/off (Vocal Cancel).
Using Song Position Markers (MIDI Song only) Song Position markers (SP1–SP4) can be placed in the MIDI Song data. This not only lets you navigate quickly and easily through the MIDI Song data, but also lets you set up convenient playback loops—allowing you to create dynamic Song arrangements “on the fly,” as you perform. Entering Song Position Markers Select the desired MIDI Song (page 74), and start playback (page 78). 2 Enter the Song Position markers. (Song Position Memorize) to turn it on.
Using Markers in loop playback In this section, we’ll explain loop playback by the example of looping between markers [1] and [2]. 1 Touch Song. 2 After passing the [1] point, touch function on. (Play/Pause) to start playback from the top of the (Loop) to turn the loop The Song plays back up to the [2] point, then goes back to [1] and loops between the two points. Top of the song 3 Song Positions [1] [2] [3] [4] To stop the loop and continue normal playback, touch (Loop) again.
Displaying Score, Lyrics, and Text files during Playback Displaying Music Notation (Score) of the MIDI Song You can view the music notation (score) of the selected MIDI Song. We suggest that you read through the music notation before starting to practice. 1 Select a MIDI Song (page 74). 2 Touch (Score) on the Song Playback display to call up the Score display. You can look through the entire notation by touching [] or [] when Song playback is stopped.
Displaying Lyrics of the MIDI Song When the selected Song contains lyric data, you can view it on the instrument’s display during playback. 1 Select a MIDI Song (page 74). 2 Touch (Lyrics) on the Song Playback display to call up the Lyrics display. When the Song data contains lyrics data, the lyrics are shown on the display. You can look through the entire lyrics by touching [] or [] when Song playback is stopped.
Adjusting the Volume Balance between SONG A and SONG B (Cross Fader) In the Dual Player mode of Song playback, the Cross Fader lets you adjust the volume balance between SONG A and SONG B playback. Moving the fader leftward increases the volume of SONG A playback, and moving rightward increases the volume of SONG B playback.
5 Operation Guide Adjusting the Parameters of Each Part— Mixer The Mixer gives you intuitive control over aspects of the keyboard parts and Song/Style channels, including volume balance and the timbre of the sounds. It lets you adjust the levels and stereo position (pan) of each Voice to set the optimum balance and stereo image, and lets you set how the effects are applied. This section covers the basic procedures for the Mixer. For details, refer to the Reference Manual on the website.
3 4 5 Touch a tab for editing the desired parameters. Filter For adjusting Resonance, and Cutoff (sound brightness). EQ For adjusting equalization parameters to correct the tone or timbre of the sound. Effect For selecting an Effect type and adjusting its depth for each part. Chorus/Reverb For selecting a Chorus/Reverb type and adjusting its depth for each part. Pan/Volume For adjusting panning and volume for each part. Set the value of each parameter. Save your Mixer settings.
Turning Each Channel of the Style or MIDI Song On/Off You can add variations and change the feeling of a Style or a MIDI Song by selectively turning channels on/off. Style Channels Each Style contains the channels listed below. • Rhythm 1/2: These are the basic parts of the Style, containing the drum and percussion rhythm patterns. • Bass: The bass part uses various appropriate instrument sounds to match the Style.
Changing the Voice for Each Channel of the Style or MIDI Song You can change the Voice for each channel via the Mixer display. 1 In the Mixer display, touch the [Style] tab or [Song] tab. 2 Touch the instrument icon below the channel name to call up the Voice Selection display, then select the desired Voice. Voice 3 As necessary, make other settings then save them as a Style file or Song file (step 5 on page 87).
6 Operation Guide Song Recording This instrument allows you to record your performance in two ways: MIDI recording and Audio recording. In addition, each way of recording features two different methods: Quick Recording, which is the easiest, most convenient way to record, and Multi Recording, which allows you to record each channel or each track independently. In this section, we’ll take a look at MIDI Quick Recording and Audio Quick Recording.
2 Start recording. You can start recording by playing the keyboard, starting the Style, playing a Multi Pad or touching [Play/Pause]. 3 After you finish your performance, touch [Stop] to stop recording. 4 Touch [Save] to call up the Song Selection display, then save the recorded performance as a file (page 37). NOTICE The recorded Song will be lost if you close the display or you turn the power off without executing the save operation.
7 Operation Guide Storing and Calling up Custom Panel Setups—Registration Memory, Playlist The Registration Memory function and the Playlist function allow you to save (or “register”) virtually all panel settings, and then instantly recall your custom panel settings for your performances by a simple, one-touch operation.
Saving and Recalling Custom Panel Setups with Registration Memory Registering Your Panel Setups 1 Make the desired panel Settings, such as those for Voices, Styles and Effects. 2 Press the [MEMORY] button in the REGISTRATION MEMORY section to call up the Registration Memory window. The list of items to be registered to Registration Memory Selecting the items to be registered The Registration Memory window contains the list for selecting the items to be registered.
Saving the Registration Memory as a Bank file You can save all ten registered panel setups as a Single Registration Memory Bank file. 1 Press the REGIST BANK [-] and [+] buttons simultaneously to call up the Registration Bank Selection display. 2 2 Touch (File Edit) to call up the pop-up window, and then touch [Save] to save the Bank file. For instructions on saving, refer to “File Management” (page 37). NOTE You can tag Registration Memory Bank files for easy search.
Confirming the Registration Memory Bank Information You can call up the information display to confirm which Voices, Style and Songs are memorized to the [1]–[10] buttons of a Registration Memory Bank. 1 Call up the Registration Bank Selection display, then select the desired Bank. 2 Touch (Menu) then [Regist Bank Info] to call up the Regist Bank Information display. This display consists of two pages: Voice-related, and Style-related. You can switch between the two via [Voice]/[Style] on the display.
Managing a Large Repertoire by Using the Playlist The Playlist is useful for managing multiple set lists for your live performances. You can select only the desired files from a large repertoire (the huge number of the Registration Memory Bank files) and create a new set list for each performance. Adding a Record to the Playlist By adding a Record to the Playlist, you can directly recall your desired Registration Memory. 1 Press the [PLAYLIST] button to call up the Playlist display.
3-2 Touch to edit the Record. Record Name Determines the name of the Record. Touching [Rename] calls up the Character Entry window. Action Additional actions after selecting the Record and recalling the Bank. • Load Regist Memory: Recalls the Registration Memory corresponding to the selected number. When no item is selected, no Registration Memory is recalled. • View: Displays the selected view. When no item is selected, no view is displayed. 3-3 Close the display. 4 Touch list file.
Creating a new Playlist 1 Press the [PLAYLIST] button to call up the Playlist display. 2 2 Touch (New) on the display. A new Playlist file is created. Copying the Playlist Records (Append Playlist) “Append Playlist” allows you to copy the existing Playlist file as a new Playlist file. 1 Press the [PLAYLIST] button to call up the Playlist display. 2 Touch [Append Playlist] on the display. The Playlist File Selection display appears. 3 Touch the desired Playlist file to append.
Changing the order of the Records in the Playlist 1 Press the [PLAYLIST] button to call up the Playlist display. 2 Change the order of the Records. 2-1 Touch the desired Record you want to move. 2-2 Touch (Up)/ (Down) to move the Record you selected in Step 2-1. 3 Touch (Save) to save the edited Playlist file. Deleting the Playlist Record from the Playlist 1 On the Playlist display, touch the desired Record to select it. 2 Touch [Delete] on the display. A confirmation message appears here.
8 Operation Guide Customizing for Optimum Performance You can customize the instrument for your own personal preferences and optimum performance. This section covers how to edit shortcuts on the Home display, set ASSIGNABLE buttons, make global settings, adjust the sound at the final output, and add expansion contents, such as Voices and Styles. Customizing the Shortcuts on the Home Display You can register an often used function to a shortcut on the Home display.
Making Global Settings (Utility) The Utility function provides a variety of convenient tools and settings for Genos. These include general settings that affect the entire instrument, as well as detailed settings for specific functions. Also included are data reset functions and storage media control, such as disk formatting. Basic Procedure 1 Call up the operation display.
Adjusting the Sound at the Final Output (Master Compressor, Master EQ) You can adjust the sound quality and the volume at the final output from Genos by making the Master Compressor and the Master EQ settings. 1 Call up the Mixer display via [MENU] [Mixer]. 2 Touch the “Master” tab. 2 3 3 4 5 Touch a tab for editing the desired parameters.
Adding New Contents—Expansion Packs By installing Expansion Packs, you can add a variety of optional Voices and Styles to the “Expansion” folder in the User drive. The installed Voices and Styles can be selected via the User tab in the Voice or Style Selection displays, allowing you to expand your music performance and creation possibilities.
9 Operation Guide System Settings This section explains how to make important overall, system-related settings, including backup/restore of settings and file data. Confirming the Firmware Version and Hardware ID You can check the firmware version and hardware ID of this instrument. 1 Call up the operation display via [MENU] [Utility]. 2 Touch [System]. The program version and the hardware ID are shown in the display.
Data Backup and Restore Data Backup You can back up all data in the User drive of this instrument (except for Expansion Voices/ Styles) and all settings to the USB flash drive as a single file. This procedure is recommended for data security and backup in case of damage. 1 Connect the USB flash drive to the [USB TO DEVICE] terminal as backup destination. 2 Call up the display via [MENU] [Utility] [Factory Reset/ Backup] page 2/2.
Connections—Using Your Instrument with Other Devices This chapter covers the connections of this instrument to other devices. To see where the connectors are located on the instrument, refer to pages 18–21. CAUTION Before connecting the instrument to other electronic components, turn off the power of all components. Also, before turning any components on or off, make sure to set all volume levels to minimum (0).
3 Connect a microphone to the [MIC INPUT] jack. For dynamic microphone connection, use the XLR connector or a standard 1/4” phone plug connector. For a condenser microphone, use the XLR connector. The combo jack accepts either XLR or 1/4” phone plug connectors. 4 5 When using a condenser microphone, turn the [+48V] switch on. Return the [MASTER VOLUME] dial to the original level. NOTICE NOTE When the [+48V] switch is turned on and off, the input from the [MIC IN] jack will be muted for a few seconds.
Disconnecting the microphone 1 Set the [MASTER VOLUME] knob and the [MIC GAIN] knob to the minimum position. 2 Set the [+48V] switch to off. 3 When using a condenser microphone, wait more than 10 seconds. 4 Disconnect the microphone from the [MIC INPUT] jack. NOTICE Disconnecting immediately can damage the condenser microphone and/or the instrument itself. Connecting the Optional Yamaha GNS-MS01 Speaker Use the [TO RIGHT SPEAKER], [TO LEFT SPEAKER] and [TO SUB WOOFER] jacks. Refer to page 118.
Using the LINE OUT SUB [3]–[4] jacks as AUX OUT jacks You can switch the function of the LINE OUT SUB [3]–[4] jacks to AUX OUT jacks from the instrument’s display called up via [MENU] [Line Out]. For details, refer to the Reference Manual on the website. NOTICE Do not route the output from the AUX OUT jacks to the AUX IN jacks.
Connecting Footswitches/Foot Controllers (ASSIGNABLE FOOT PEDAL jacks) One or two optional Yamaha FC4A or FC5 Footswitches and an optional Yamaha FC7 Foot Controller can be connected to these ASSIGNABLE FOOT PEDAL jacks. A footswitch can be used for switching functions on and off, while a foot controller can be used to control continuous parameters, such as volume. FC7 FC5 NOTE Do not connect or disconnect any of the pedals when the power is on.
Connecting USB Devices ([USB TO DEVICE] terminal) You can connect a USB flash drive to the [USB TO DEVICE] terminal, and save data you’ve created on the instrument to the drive (page 37). Precautions when using the [USB TO DEVICE] terminal This instrument features a built-in [USB TO DEVICE] terminal. When connecting a USB device to the terminal, be sure to handle the USB device with care. Follow the important precautions below.
Formatting a USB flash drive or the internal User drive To format a USB flash drive or the internal User drive, execute the Format operation. In order to format a USB flash drive, make sure that a USB flash drive is properly connected to the [USB TO DEVICE] terminal beforehand. 1 Connect a USB flash drive for formatting to the [USB TO DEVICE] terminal. 2 Call up the operation display via [MENU] [Utility] [Storage]. NOTICE The Format operation deletes any previously existing data.
Connecting to a Computer ([USB TO HOST] terminal) By connecting a computer to the [USB TO HOST] terminal, you can transfer data between the instrument and the computer via MIDI. For details on using a computer with this instrument, refer to the “Computer-related Operations” on the website. NOTICE Use an AB type USB cable of less than 3 meters. USB 3.0 cables cannot be used.
Viewing the Instrument’s Display on an External Monitor By connecting with an external monitor such as a television, you can separately show the lyrics/text or duplicate the instrument display (mirroring) on an external monitor. Use a USB display adaptor and a display cable which are compatible with both this instrument and the monitor to connect to the [USB TO DEVICE] terminal of this instrument. For a list of compatible USB display adaptors, visit the following website: https://download.yamaha.
Memo Connections—Using Your Instrument with Other Devices 115 Genos Owner’s Manual
Function List This section simply and very briefly explains what you can do in the displays called up by pressing the buttons on the panel, or by touching each icon on the Menu display. For more information, refer to the page indicated below or the Reference manual on the website. The “” mark indicates that the detailed information is described in the Reference Manual.
Menu Panel Lock Demo Voice Edit Style Creator Song Recording M.Pad Creator Voice Setting Style Setting Song Setting Chord Tutor Scale Tune Master Tune Transpose Keyboard/Joystick MIDI Utility Wireless LAN* Time Expansion Description For locking the panel settings. When the panel settings are locked, nothing happens even when pressing any panel buttons. For calling up the Demo display. For editing the preset Voices to create your own Voices.
Appendix Installing the Optional Speakers Make sure that all of the parts below have been included in the GNS-MS01 speaker package. Satellite speakers (2) Subwoofer speaker (1) Speaker brackets (2) Phone cables (2) 8-pin mini DIN cable (1) 1 Turn Genos’s power off, and disconnect the AC power cord. Also, make sure to disconnect the keyboard from any other external devices. 2 Insert the two speaker brackets to the rear panel of Genos.
5 Use the 8-pin mini DIN cable to connect the subwoofer to Genos. Genos Subwoofer 6 Connect the supplied AC power cord to the subwoofer. 7 Connect the power plugs of Genos and the subwoofer to an appropriate AC outlet. 8 Set the volume controls (MASTER VOLUME on Genos and MAIN VOLUME on the subwoofer) to minimum. Genos (Rear panel) Turn on the power of Genos, then the subwoofer. Genos Subwoofer Installing the Optional Speakers 9 Subwoofer (Front panel) Turn the Genos on.
Direct Access Chart Press the [DIRECT ACCESS] button, then press one of the buttons (or move the appropriate knob, slider, joystick or pedal) listed below to call up the desired display.
MULTI PAD Control MULTI PAD SELECT STOP 1 2 3 4 ENTER EXIT DIAL INC DEC VOICE PART SELECT LEFT PART SELECT R1 PART SELECT R2 PART SELECT R3 PART ON/OFF LEFT PART ON/OFF R1 PART ON/OFF R2 PART ON/OFF R3 Display called up with the Direct Access function (Multi Pad Selection) - - Multi Pad Edit Menu Home - - - ASSIGNABLE Voice Setting - - Menu Assignable Menu Registration Bank Edit Registration Bank Edit Registration Freeze Registration Sequence - - - Chorus Reverb Panel - - - - -
Troubleshooting Overall A click or pop is heard when the power is turned on or off. This is normal. Electrical current is being applied to the instrument. The power is automatically turned off. This is normal and due to the Auto Power Off function. If necessary, set the parameter of the Auto Power Off function (page 24). Noise is heard from the instrument. Noise may be heard if a mobile phone is used near the instrument or if the phone is ringing.
Only the rhythm channel plays. Make sure the Auto Accompaniment function is turned on; press the [ACMP] button. Make sure to play keys in the chord range of the keyboard. Styles in a USB flash drive cannot be selected. If the size of the Style data is large (about 120 KB or greater), the Style cannot be selected because the data is too large to be read by the instrument. Style playback seems to “skip” when the keyboard is played. You are probably exceeding the maximum polyphony of the instrument.
Mixer The sound seems strange or different than expected when changing a rhythm Voice (drum kit, etc.) of the Style or Song from the Mixer. When changing the rhythm/percussion Voices (drum kits, etc.) of the Style and Song from the VOICE parameter, the detailed settings related to the drum voice are reset, and in some cases you may be unable to restore the original sound. You can restore the original sound by selecting the same Song or Style again.
Specifications Product Name Size/Weight Digital Keyboard Dimensions (W x D x H) 1234 mm x 456 mm x 138 mm (48-9/16” x 17-15/16” x 5-7/16”) Weight Control Interface Keyboard 13.0kg (28 lbs., 11 oz.
Multi Pads Number of Multi Pad Banks 448 Banks x 4 Pads Audio Link Functions Voices Styles Songs Yes Harmony Yes Arpeggio Yes Panel Sustain Yes Mono/Poly Yes Style Creator Yes OTS Information Yes Score Display Function Yes Lyrics Display Function Lesson/Guide Multi Pads Multi Pad Creator Registration Memory Number of Buttons Control Playlist Number of Records Search Transpose Tuning Octave Button Scale Type Others Storage and Connectivity Storage 2,500 (max.
Index A F A-B Repeat ..................................... 80 AC IN .............................................. 23 Accessories....................................... 9 Accompaniment .............................. 44 Action (Playlist) ............................... 97 AI Full Keyboard ............................. 46 Arpeggio.......................................... 57 ASSIGNABLE Buttons .................. 100 Audio Link Multi Pad ....................... 59 Audio Song .................................
R V Record Name (Playlist) ................... 97 Recording.................................. 17, 90 Reference Manual........................... 10 Registration Memory ................. 17, 92 Registration Memory Bank........ 31, 92 Registration Sequence.................... 31 Rename .......................................... 38 Restore ......................................... 105 Reverb ............................................ 87 Revo Drum, Revo SFX Voice.......... 52 Rewind ........................
GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright © 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble 2. The licenses for most software are designed to take away your freedom to share and change it.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 5.
GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright © 1991, 1999 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.
d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.
10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License.
libpng This copy of the libpng notices is provided for your convenience. In case of any discrepancy between this copy and the notices in the file png.h that is included in the libpng distribution, the latter shall prevail. COPYRIGHT NOTICE, DISCLAIMER, and LICENSE: If you modify libpng you may insert additional notices immediately following this sentence. This code is released under the libpng license. libpng versions 1.0.7, July 1, 2000 through 1.6.
FreeType libss2 / libcomerr2 Portions of this software are copyright © 2016 The FreeType Project (www.freetype.org). All rights reserved. Copyright 1987, 1988 by the Student Information Processing Board of the Massachusetts Institute of Technology ICU COPYRIGHT AND PERMISSION NOTICE Copyright © 1991-2016 Unicode, Inc. All rights reserved. Distributed under the Terms of Use in http://www.unicode.org/copyright.html.
Genos Owner’s Manual
1-YEAR LIMITED WARRANTY ON ARRANGER WORKSTATION KEYBOARDS Thank you for selecting a YAMAHA product. YAMAHA products are designed and manufactured to provide a high level of defect-free performance. Yamaha Corporation of America (“YAMAHA”) is proud of the experience and craftsmanship that goes into each and every YAMAHA product.
SIMPLIFIED EU DECLARATION OF CONFORMITY / SIMPLIFIED UK DECLARATION OF CONFORMITY Hereby, Yamaha Music Europe GmbH declares that the radio equipment type [Genos] is in compliance with Directive 2014/53/EU and the radio equipment regulations of UK. The full texts of the EU declaration of conformity and the UK declaration of conformity are available at the following internet address: https://europe.yamaha.com/en/support/compliance/doc.
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Toronto, Ontario M1S 3R1, Canada Tel: +1-416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Avenue, Buena Park, CA 90620, U.S.A.
Yamaha Global Site https://www.yamaha.com/ Yamaha Downloads https://download.yamaha.
