User Manual
Table Of Contents
- PRECAUTIONS
- NOTICE
- Information
- Compatible formats for this instrument
- About the Manuals
- Included Accessories
- Contents
- Welcome to the World of CVP!
- Panel Controls
- Starting Up
- Basic Operations
- Display Structure
- Display Configuration
- Closing the Current Display
- Display-based Controls
- Using the ASSIGNABLE Buttons
- File Management
- Entering Characters
- Using the Pedals
- Using the Metronome
- Adjusting the Tempo
- Setting the Touch Sensitivity of the Keyboard
- Transposing the Pitch in Semitones
- Adjusting the Volume Balance
- Restoring the Factory-programmed Settings (Initializing)
- Data Backup
- Piano Room – Enjoying the Piano Performance –
- Voices – Playing the Keyboard –
- Playing Preset Voices
- Setting the Split Point
- Calling up the Appropriate Settings for Piano Performance (Piano Reset)
- Locking the Settings for Piano Performance (Piano Lock)
- Playing Realistic Resonance-enhanced Piano Sounds (VRM Voices)
- Playing Super Articulation Voices
- Creating Original Organ Flutes Voices
- Styles – Playing Rhythm and Accompaniment –
- Song Playback – Playing and Practice Songs –
- Song Recording – Recording Your Performance –
- Microphone – Adding Vocal Harmony Effects to Your Singing –
- Registration Memory/Playlist – Saving and Recalling Custom Panel Setups –
- Mixer – Editing the Volume and Tonal Balance –
- Connections – Using Your Instrument with Other Devices –
- I/O Connectors
- Connecting USB Devices ([USB TO DEVICE] terminal)
- Connecting to a Computer ([USB TO HOST] terminal/MIDI terminals)
- Connecting to a Smart Device ([AUX IN] jack/Bluetooth/[USB TO HOST] terminal/Wireless LAN)
- Listening to Audio Playback by the External Device through the Instrument’s Speaker ([AUX IN] jack/Bluetooth/[USB TO HOST] terminal)
- Using an External Speaker System for Playback (AUX OUT [L/L+R]/[R] jacks)
- Connecting External MIDI Devices (MIDI terminals)
- Viewing the Instrument’s Display on an External Monitor
- Connecting a Microphone or Guitar ([MIC/LINE IN] jack)
- Connecting a Footswitch/Foot Controller ([AUX PEDAL] jack)
- Menu Display Function List
- CVP-809 (Grand piano type) Assembly
- CVP-809 Assembly
- CVP-805 Assembly
- Troubleshooting
- Specifications
- Index
CVP-809/CVP-805 Owner’s Manual
115
CVP-809 (Grand piano type) Assembly
5 Install the pedal box.
1 Remove the twist tie and tape that affix the pedal cord to
the upper portion of the pedal box.
.
2 Attach the front side of the pedal box to the bottom of the
unit by finger-tightening the two fixing screws (6 x 20 mm).
3 Insert the lyre braces into the pedal box recesses and make
sure they fit securely.
4 Align the cord with the groove on the unit and attach the
backside of the pedal box using the two fixing screws (6 x
20 mm), and then securely tighten the two screws of the
front side of the pedal box that were attached in step 5-2.
5 Loosen the four screws that were attached in step 3, and
then securely tighten the four screws again while pushing
the lyre braces in the direction of arrows as illustrated.
6 Insert the pedal cord plug into the pedal connector. Insert
the plug so the arrow side faces front (toward the
keyboard).
If the plug will not go in easily, do not force it. Double-
check the orientation of the plug, then try again.
7 Attach the cord holder to the bottom of the main unit as
shown, then clip the holder around the cord.
Twist tie
Ta pe
6 x 20 mm
fixing screws
6 x 20 mm fixing screws
6
7
Insert the pedal
cord securely
until the metal
part of the cord
plug disappears
from view.
Otherwise, the
pedal may not
function properly.