User Manual
Table Of Contents
- Notice regarding data copyright
- Notice regarding the content of this user guide
- Contents
- Chapter 1. An overview of MTX-MRX Editor
- An audio system control network
- Terms used in this user guide
- Data handled by MTX-MRX Editor
- Connection requirements for an MTX/MRX system
- MTX/MRX system configuration examples
- What are YDIF connections? (Cascade mode and Distribution mode)
- What are Dante connections? (Daisy-chain connection and Star connection)
- Patching
- Workflow
- About the screens
- Moving between screens
- Chapter 2. Menu bar and tool buttons
- Chapter 3. Project screen
- Chapter 4. System screen
- Chapter 5. Online and Synchronization
- Chapter 6. Presets
- Chapter 7. Dialog boxes/Software applications
- “Startup” dialog box
- “Network Setup” dialog box
- “Device Information” dialog box
- “Match Device by IP Address” dialog box
- “MTX Configuration” dialog box
- “Dante Information” dialog box
- “Word Clock” dialog box
- “Clock” dialog box
- “Daylight Saving Time” dialog box
- “Scheduler” dialog box
- “Remote Control” dialog box
- “External Events” dialog box
- “Digital Control Panel” dialog box
- “Wireless DCP” dialog box
- “MCP1” dialog box
- “PIN Setup” dialog box
- “Label” dialog box
- “Re-size Image” dialog box
- “PGM1/PGX1” dialog box
- “PGM1 Label Creator” application
- “GPI” dialog box
- “GPI Calibration” dialog box
- “Security Settings” dialog box
- “Project Information” dialog box
- “Configuration Diagram” dialog box
- “Get Log” dialog box
- “Sampling Rate Converter” dialog box
- “Input Source/Redundant” dialog box
- Appendix
Workflow Chapter 1. An overview of MTX-MRX Editor
MTX-MRX Editor User Guide
21
Make DCP, Wireless DCP, MCP1, PGM1/PGX1, GPI, and Scheduler settings.
You’ll make these settings in the following dialog boxes.
DCP settings: “Digital Control Panel” dialog box
(On the [Controller] menu, click [Digital Control Panel].)
Wireless DCP settings: “Wireless DCP” dialog box
(On the [Controller] menu, click [Wireless DCP].)
MCP1 settings: “MCP1” dialog box
(On the [Controller] menu, click [MCP1].)
PGM1/PGX1 settings: In the “ZONE” screen, [PAGING] and the “PGM1/PGX1”
dialog box
(On the [Controller] menu, click [PGM1/PGX1].)
GPI settings: “GPI” dialog box or “GPI Calibration” dialog box
(On the [System] menu, click [GPI] or [GPI Calibration].)
Schedule settings: “Scheduler” dialog box
(On the [System] menu, click [Scheduler])
Store the preset.
You’ l l u s e t h e “Preset” dialog box to store the preset. To open the “Preset” dialog box, click
the preset button.
For details on the DCP library, Wireless DCP library, MCP1 library, and audio file settings
that are recalled at the same time as a preset, refer to “Preset” dialog box.
Connect your devices as shown in the configuration diagram you printed.
Turn off the power of each device, and set the UNIT ID on the rear panel of the
MTX/MRX, XMV, EXi8/EXo8, and PGM1 units. For the MCP1, turn on the power
before setting the UNIT ID.
You can also print the configuration diagram by clicking [Print Configuration Diagram] on the
[File] menu.
First make sure that DIP switch 6 (IP SETTING) on the unit’s rear panel is set to [UNIT
ID]. If it is set to [PC], change it to [UNIT ID] and then restart the device.
“Preset” dialog box
Preset button
NOTE