User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon and channel color
- Making HA (Head Amp) settings
- Sending a signal from an input channel to the STEREO/MONO buses
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Correcting delay between channels (Input Delay)
- Channel library operations
- Output channels
- EQ and Dynamics
- Grouping and linking
- Scene memory
- About scene memories
- Using scene memories
- Editing scene memories
- Using the Global Paste function
- Using the Focus function
- Using the Recall Safe function
- Using the Fade function
- Outputting a control signal to an external device in tandem with scene recall (GPI OUT)
- Playing back an audio file that links to a scene recall
- Using Preview mode
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, effects, and Premium Rack
- I/O device and external head amp
- MIDI
- User settings (Security)
- Recorder
- Help function
- Other functions
- About the SETUP screen
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Appendices
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Effects and tempo synchronization
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- Functions that can be assigned to USER DEFINED keys
- Functions that can be assigned to USER DEFINED knobs
- Functions that can be assigned to the assignable encoders
- MIDI Data Format
- Warning/Error Messages
- Electrical characteristics
- Mixer Basic Parameters
- M IDI Implementation Chart
- Index
Monitor and Cue functions
Reference Manual
101
8. To adjust the monitor level, use the MONITOR LEVEL knob located in the SCENE
MEMORY/MONITOR section of the top panel.
If PHONES LEVEL LINK is ON, use the MONITOR LEVEL knob and the monitor fader, as well
as the PHONES LEVEL knob to adjust the monitor level when monitoring through headphones.
9. Make settings for Dimmer, Delay, Monaural, and CUE INTERRUPTION as desired.
NOTE
Monitor on/off operations, selection of the monitor source, and dimmer on/off operations can also
be assigned to USER DEFINED keys (see page 169).
Using the Cue function
About CUE groups
Cue signals on the CL series console can be categorized into the following four groups.
1 INPUT CUE group
The cue signals of input channels make up this group. To enable Cue for this group, press the
[CUE] key for any input channel to turn Cue on.
NOTE
If input channels or ST IN channels are assigned to the Centralogic section, you can also use the
[CUE] keys in the Centralogic section to enable Cue for this group.
2 DCA CUE group
The cue signals of DCA groups make up this group. To enable Cue for this group, press the [CUE]
key of one of the DCA groups to turn Cue on.
3 OUTPUT CUE group
The cue signals of output channels make up this group. To enable Cue for this group, press the
[CUE] key of one of the output channels.
Input channel [CUE] key
Centralogic section [CUE] key
(when controlling DCA groups)
[CUE] key in the Master section