User Manual

Appendices
Reference Manual
261
*1) CL5: CH1–CH72, CL3: CH1–CH64, CL1: CH1–CH48, ST IN 1L–ST IN 8R, MIX1–MIX24, MTRX1–MTRX8,
ST L, ST R, MONO(C)
*2) CL5: CH1–CH72, CL3: CH1–CH64, CL1: CH1–CH48, ST IN 1–ST IN 8, MIX1–MIX24, MTRX1–MTRX8,
STEREO, MONO(C)
*3) MIX1–MIX24, MTRX1–MTRX8, ST L, ST R, MONO(C)
*4) CL5: CH1–CH72, CL3: CH1–CH64, CL1: CH1–CH48, ST IN 1–ST IN 8, MIX1–MIX24, MTRX1–MTRX8,
STEREO, MONO(C), DCA1–DCA16
PAGE
CHANGE
BOOKMARK
Memorize the currently selected screen (hold
down the key for two seconds or longer), or
display the last-memorized screen (press and
release the key within two seconds). Popup
screens can also be memorized. In the case of a
rack, the number of that rack is also
memorized.
BOOKMARK with “SEL” —
Memorize the above BOOKMARK with the
addition of the SEL status.
PREVIOUS PAGE
— Display the previous/next page.
NEXT PAGE
CLOSE POPUP — Close the displayed popup window.
RECORDER
TRANSPORT
PLAY/PAUSE, STOP,
FF/NEXT,
REW/PREVIOUS, REC
Display the previous/next page.
AUTO REC
Shortcut function for STOP → REC → PLAY.
Recording will be initiated in a single action. If
this is executed during recording, the file being
recorded will first be closed, and then
recording will continue with a new file.
REC & START
Start recording immediately without entering
record-ready mode.
DIRECT PLAY
NO ASSIGN The specified audio file will be played once
from the beginning. Audio files to be played
should be saved in the SONGS folder inside the
YPE folder. Please note that a file cannot be
specified if it is saved in the root directory or in
any other folder. When you execute playback,
the path in the TITLE LIST screen will move to
\YPE\SONGS\.
(TITLE 1)
:
SCENE
INC RECALL — Recall the scene of the next existing number.
REC RECALL —
Recall the scene of the previous existing
number.
DIRECT RECALL SCENE #000–#300
Directly recall the scene of the specified
number.
RECALL UNDO — Execute RECALL UNDO.
STORE UNDO — Execute STORE UNDO.
SEND
ENCOD
ER
MODE
MIX1-16/MIX17-24,
MATRIX
—
If INPUT or ST IN is selected, switch the
function of the Selected Channel section’s send
encoders from TO MIX1-16/TO MIX17-24,
MATRIX.
SENDS ON
FADER
MIX1–MIX24
—
Switches the MIX ON FADER function for the
selected MIX on and off.
MTRX1–MTRX8
Switches the MATRIX ON FADER function for
the selected MATRIX on and off.
MIX ON FADER
Switches the MIX ON FADER function on and
off.
MATRIX ON FADER
Switches the MATRIX ON FADER function on
and off.
SENDS ON FADER
Switches the SENDS ON FADER function on
and off.
FUNCTION PARAMETER 1 PARAMETER 2 Explanation
SET BY SEL
SET [+48V]
—
Hold down this key and press SEL to switch it
on/off.
During this time, the [SEL] LED will be lit if on
or dark if off.
If SET [PRE SEND] is selected, “SEND ON
FADER” mode is engaged while you are
holding down the [SEL] key.
SET [Ø]
SET [INSERT ON]
SET [DIRECT OUT ON]
SET [PRE SEND]
SET [TO STEREO]
SET [TO MONO]
SET [TO LCR]
SET [GAIN
COMPENSATION]
SET DEFAULT
VALUE
——
While holding down this key, press a knob in
the Selected Channel or Centralogic section to
reset it to the default value.
SET
NOMINAL
VALUE
——
While holding down this key, press a [SEL] key
to set the fader of that channel to nominal
level.
TALKBACK
TALKBACK ON
LATCH Switch TALKBACK on/off.
UNLATCH Turn TALKBACK on while pressed.
SELECTED CH ASSIGN —
While holding down this key, press a SEL key of
an OUTPUT channel to switch the assignment
on/off. During this time, the [SEL] LED will be
lit if assign is ON, or dark if OFF.
The assignment setting made while holding
down this key will be stored. Pressing the key
again will recall the stored setting. Settings can
be stored in multiple keys to facilitate rapid
assignment switching.
DIRECT ASSIGN *3)
Assign TALKBACK to the channel selected from
list 3).
TAP TEMPO
CURRENT PAGE —
Use the tap tempo function in the displayed
screen.
EFFECT RACK1–8 —
Use the tap tempo function for the specified
effect.
FUNCTION PARAMETER 1 PARAMETER 2 Explanation