User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon and channel color
- Making HA (Head Amp) settings
- Sending a signal from an input channel to the STEREO/MONO buses
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Correcting delay between channels (Input Delay)
- Channel library operations
- Output channels
- EQ and Dynamics
- Grouping and linking
- Scene memory
- About scene memories
- Using scene memories
- Editing scene memories
- Using the Global Paste function
- Using the Focus function
- Using the Recall Safe function
- Using the Fade function
- Outputting a control signal to an external device in tandem with scene recall (GPI OUT)
- Playing back an audio file that links to a scene recall
- Using Preview mode
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, effects, and Premium Rack
- I/O device and external head amp
- MIDI
- User settings (Security)
- Recorder
- Help function
- Other functions
- About the SETUP screen
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Appendices
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Effects and tempo synchronization
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- Functions that can be assigned to USER DEFINED keys
- Functions that can be assigned to USER DEFINED knobs
- Functions that can be assigned to the assignable encoders
- MIDI Data Format
- Warning/Error Messages
- Electrical characteristics
- Mixer Basic Parameters
- M IDI Implementation Chart
- Index
Output channels
Reference Manual
54
Using the faders (SENDS ON FADER mode)
You can use the faders on the top panel to adjust signals that are sent from the MIX and STEREO/
MONO channels to a specific MATRIX bus.
1. Make sure that an output port is assigned to the MATRIX bus to which you want
to send signals, and that your monitor system etc. is connected to the
corresponding output port.
2. In the function access area, press the SENDS ON FADER button.
The CL series unit will switch to SENDS ON FADER mode. The faders in the Channel Strip
section and Master section will move to the send levels of the signals that are routed from each
channel to the currently-selected MIX/MATRIX bus. The [ON] keys will also change to the SEND
ON status.
In SENDS ON FADER mode, the Function Access Area in the display will show the buttons that
enable you to switch between MIX 1-16 ON FADER mode and MIX 17-24/MATRIX ON FADER
mode, and the buttons that enable you to select the destination MIX/MATRIX buses.
3. Use the MIX 1-16 and MIX 17-24/MATRIX select buttons to switch between MIX 1-
16 and MIX 17-24/MATRIX.
Now you can use the MIX/MATRIX bus select buttons to specify the destination MIX/MATRIX
buses.
4. Use the MIX/MATRIX bus selection buttons in the function access area to select the
send-destination MATRIX bus.
NOTE
• Alternatively, press a SEND LEVEL knob in the SELECTED CHANNEL section to display a
popup window, from which you can select a MIX/MATRIX bus.
• You can also select a MIX/MATRIX bus by using the Bank Select keys and the [SEL] keys in the
Centralogic section. If you switch buses by pressing the [SEL] keys, the setting of the MIX 1-16
and MIX 17-24/MATRIX ON FADER switch buttons will also be change automatically.
• If you press the currently-selected MIX/MATRIX bus select button again, cue monitoring will be
turned on for the corresponding MIX/MATRIX channel. This method is convenient if you want to
monitor the signal that is being sent to the selected MIX/MATRIX bus.
5. Use the faders in the top panel Centralogic section to adjust the send level from
the MIX and STEREO/MONO channels to the selected MATRIX bus.
NOTE
You can assign the SENDS ON FADER function to a USER DEFINED key. This lets you quickly
switch to SENDS ON FADER mode for a specific MIX/MATRIX bus, and quickly switch back
again.
6. Repeat steps 4–5 to adjust the send level for other MATRIX buses in the same way.
7. When you’re finished adjusting the MATRIX send levels, press the X symbol in the
function access area.
The Function Access Area display will return to its prior state, and the CL console will exit SENDS
ON FADER mode and return to normal mode.