User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Correcting delay between channels (Input Delay)
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- MIDI Data Format
- Input/Output Specifications
- Electrical characteristics
- Mixer Basic Parameters
- Pin Assignment Chart
- MIDI Implementation Chart
Recorder
Reference Manual
148
Channels that can be patched to the recorder’s outputs
• CH1–64 (QL5), CH1–32 (QL1)
............................. INPUT channel 1–64 (QL5) or INPUT channel 1–32 (QL1)
• STIN 1L/1R-STIN 8L/8R
............................. ST IN channels 1–8L/R
Recording audio to a USB flash drive
You can record the signal of the desired output channels as an audio file (MP3) onto the USB
flash drive inserted in the USB connector located to the right of the display.
NOTE
• The FREE SIZE field indicates the amount of free capacity in the USB flash drive.
• The signal being recorded will not be output from the recorder output jacks (PLAYBACK OUT).
• The level meter on the RECORDER screen shows the signal level before and after the recorder.
If necessary, use the GAIN knob in the RECORDER INPUT field to adjust the input level to the
recorder. Operating the GAIN knob will not affect the level of the signal being output to other ports
from the corresponding output channel.
• In the default state, the recorded audio file will be saved in the SONGS folder within the YPE
folder in the USB flash drive. However, you may also specify a folder of a level below the SONGS
folder.
• The recorded file will be given a default title and file name. You can change this later.
RECORDER screen (when selecting the USB tab)
TRANSPORT field
This field enables you to control recording and playback of a song.
1 Current song
Indicates the currently-selected song’s track number, title and artist name. The following
indicators will appear during playback or recording.
2 Elapsed time display
Indicates the elapsed playback time of the current song during playback, and the
elapsed recording time during recording.
3 Remaining time display
During playback, this indicates the remaining playback time of the current song.
4 Current song format
Indicates the file format information for the current song (the file being recorded).
STEP
1. Refer to “Assigning channels to the input/output of the recorder” on page 146 to
assign channels to the input/output of the recorder.
2. Connect a USB flash drive with sufficient free capacity to the USB connector.
3. To monitor the signal being recorded, raise the fader for the channel(s) that are
patched to the input of the recorder.
4. Press the REC RATE button in the lower right of the RECORDER screen, then select
the bit rate for the audio file that will be recorded.
5. Press the REC () button located at the bottom of the screen.
6. To start recording, press the PLAY/PAUSE ( ) button in the lower part of the
screen.
7. To stop recording, press the STOP () button.
8. To audition the recorded content, proceed as follows.
8-1. Press the PLAY/PAUSE ( ) button to play back the recording.
8-2. To stop playback, press the STOP () button.
1
2
3 4A0987 5 6
Playing
Recording