User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Correcting delay between channels (Input Delay)
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- MIDI Data Format
- Input/Output Specifications
- Electrical characteristics
- Mixer Basic Parameters
- Pin Assignment Chart
- MIDI Implementation Chart
Setup
Reference Manual
171
CUE
OUTPUT Switch CUE on/off.
CLEAR CUE
SPECIFIC CH *2) CUE the channel selected from list 2).
CUE MODE Select the CUE MODE.
EFFECT
BYPASS
EFFECT RACK1–8
PREMIUM RACK1A
PREMIUM RACK1B
:
PREMIUM RACK8A
PREMIUM RACK8B
GAIN KNOB
FUNCTION
LATCH —
Toggle the function of the GAIN knob (ANALOG
GAIN/DIGITAL GAIN). Lit when DIGITAL GAIN is
selected.
UNLATCH —
Assign the function of the GAIN knob (ANALOG
GAIN/DIGITAL) to DIGITAL GAIN only while held
down.
* However if the GAIN KNOB FUNCTION is
switched to DIGITAL GAIN in the PREFERENCE
screen etc., this will remain lit until the next time
it is pressed.
GEQ FREQ
BANK
INC
—
Adds or removes a frequency bank in the GEQ
EDIT screen.
DEC
GPI OUT
LATCH
PORT1–PORT5
Toggle the GPI OUT function. Lit when active.
UNLATCH Make GPI OUT active only while pressed.
HELP — —
Opens and closes the HELP window. Operating
the controllers on the panel (excluding faders),
or controllers on the screen, while holding down
this key will display the related information.
HOME
SELECTED CH VIEW — Displays the SELECTED CHANNEL VIEW screen.
OVERVIEW — Displays the OVERVIEW screen.
TOGGLE —
Each press of the key will alternately display the
SELECTED CHANNEL VIEW screen and the
OVERVIEW screen.
METER PEAK HOLD ON —
Turns the meter’s peak hold function on/off. Lit
when on.
MIDI
PROGRAM CHANGE PGM 1–128
Transmit the corresponding MIDI message.
CONTROL CHANGE
CC 1–31, 33–95,
102–119
NOTE ON
NOTE ON C-2 (0)
:
NOTE ON G 8 (127)
FUNCTION PARAMETER 1 PARAMETER 2 Explanation
MONITOR
MONITOR ON — Switch MONITOR on/off.
OUTPUT Switch the monitor output on/off.
SELECTED CH ASSIGN —
While holding down this key, press the SEL key
of a MIX or MATRIX channel to switch the
assignment on/off. During this time, the [SEL]
LED will be lit if assign is ON, or dark if OFF.
The assignment setting made while holding
down this key will be stored. Pressing the key
again will recall the stored setting. Settings can
be stored in multiple keys to facilitate rapid
assignment switching.
DIMMER ON
Enable the dimmer and attenuate the monitor
signal.
SOURCE SELECT
STEREO L/R
Recall the selected signal to the monitor.
MONO (C)
LCR
PB OUT
*5)
DEFINE
MUTE
MASTER
MUTE GROUP 1
— Switch MUTE GROUP MASTER on/off.:
MUTE GROUP 8
ALL MUTE —
Turns all MUTE GROUP MASTER settings on/off
together.
NUENDO
LIVE
TRANSPORT
GO TO PROJECT START
Operate the transport functions of Nuendo Live.
GO TO PREV MARKER
REWIND
FAST FORWARD
GO TO NEXT MARKER
GO TO PROJECT END
CYCLE
STOP
START
REC
EASY RECORDING
PEAK CLEAR —
Clear the peak indicators of the Nuendo Live
screen.
OSCILLATOR
OSCILLATOR ON — Switch the OSC on/off.
SELECTED CH ASSIGN —
While holding down this key, press a SEL key of a
channel to switch the assignment on/off. During
this time, the [SEL] LED will be lit if assign is ON,
or dark if OFF.
DIRECT ASSIGN *1)
Assign the oscillator to the channel selected
from list 1).
FUNCTION PARAMETER 1 PARAMETER 2 Explanation