Motorcycle User Manual
Table Of Contents
- R1 EXUP DELTABOX V YZFR1X(C) OWNER'S MANUAL
- INTRODUCTION
- IMPORTANT MANUAL INFORMATION
- TABLE OF CONTENTS
- SAFETY INFORMATION
- DESCRIPTION
- INSTRUMENT AND CONTROL FUNCTIONS
- Main switch/steering lock
- Indicator and warning lights
- Multi-function meter unit
- Handlebar switches
- Clutch lever
- Shift pedal
- Brake lever
- Brake pedal
- Fuel tank cap
- Fuel
- Catalytic converters
- Seats
- Helmet holders
- Adjusting the front fork
- Adjusting the shock absorber assembly
- Luggage strap holders
- EXUP system
- Sidestand
- Ignition circuit cut-off system
- PRE-OPERATION CHECKS
- OPERATION AND IMPORTANT RIDING POINTS
- PERIODIC MAINTENANCE AND MINOR REPAIR
- PERIODIC MAINTENANCE
- Owner's tool kit
- Periodic maintenance chart for the emission control system
- General maintenance and lubrication chart
- Removing and installing cowlings and panels
- Checking the spark plugs
- Canister (for California only)
- Engine oil and oil filter cartridge
- Coolant
- Checking and replacing the air filter element
- Checking the engine idling speed
- Checking the throttle cable free play
- Valve clearance
- Tires
- Cast wheels
- Accessories and replacement parts
- Adjusting the clutch lever free play
- Adjusting the rear brake light switch
- Checking the front and rear brake pads
- Checking the brake fluid level
- Changing the brake fluid
- Drive chain slack
- Cleaning and lubricating the drive chain
- Checking and lubricating the cables
- Checking and lubricating the throttle grip and cable
- Checking and lubricating the brake and clutch levers
- Checking and lubricating the shift pedal
- Checking and lubricating the sidestand
- Lubricating the swingarm pivots
- Checking the front fork
- Checking the steering
- Checking the wheel bearings
- Battery
- Replacing the fuses
- Replacing a headlight bulb
- Tail/brake light
- Replacing a turn signal light bulb
- Replacing the license plate light bulb
- Replacing an auxiliary light bulb
- Supporting the motorcycle
- Front wheel
- Rear wheel
- Troubleshooting
- Troubleshooting charts
- MOTORCYCLE CARE AND STORAGE
- SPECIFICATIONS
- CONSUMER INFORMATION
- INDEX
INSTRUMENT AND CONTROL FUNCTIONS
3-7
3
3. Push the “SELECT” button, and
the minute digits will start flashing.
4. Push the “RESET” button to set
the minutes.
5. Push the “SELECT” button and
then release it to start the clock.
Odometer, tripmeter, and stopwatch
modes
Push the “SELECT” button to switch
the display between the odometer
mode “ODO”, the tripmeter modes
“TRIP A” and “TRIP B” and the stop-
watch mode in the following order:
TRIP A → TRIP B → ODO → Stop-
watch → TRIP A
If the fuel level warning light comes on
(see page 3-2), the odometer display
will automatically change to the fuel re-
serve tripmeter mode “F-TRIP” and
start counting the distance traveled
from that point. In that case, push the
“SELECT” button to switch the display
between the various tripmeter, odome-
ter, and stopwatch modes in the follow-
ing order:
F-TRIP → Stopwatch → TRIP A →
TRIP B → ODO → F-TRIP
To reset a tripmeter, select it by push-
ing the “SELECT” button, and then
push the “RESET” button for at least
one second. If you do not reset the fuel
reserve tripmeter manually, it will reset
itself automatically and the display will
return to the prior mode after refueling
and traveling 5 km (3 mi).
Stopwatch mode
To change the display to the stopwatch
mode, select it by pushing the “SE-
LECT” button. (The stopwatch digits
will start flashing.) Release the “SE-
LECT” button, and then push it again
for a few seconds until the stopwatch
digits stop flashing.
Standard measurement
1. Push the “RESET” button to start
the stopwatch.
2. Push the “SELECT” button to stop
the stopwatch.
3. Push the “SELECT” button again
to reset the stopwatch.
Split-time measurement
1. Push the “RESET” button to start
the stopwatch.
2. Push the “RESET” button or start
switch “” to measure split-times.
(The colon “:” will start flashing.)
3. Push the “RESET” button or start
switch “” to display the final split-
time or push the “SELECT” button
to stop the stopwatch and display
total elapsed time.
4. Push the “SELECT” button to reset
the stopwatch.
NOTE:
To change the display back to the prior
mode, push the “SELECT” button for a
few seconds until the stopwatch digits
flash.
1. Odometer/tripmeters/fuel reserve tripme-
ter/stopwatch
U4C811E0.book Page 7 Thursday, June 7, 2007 2:38 PM